Interfacial Transformation of an Amorphous Carbon Nanofilm upon Fe@Ag@Si Nanoparticle Landing and its Colloidal Nanoscrolls: Enhanced Nanocompositing-Based Performance for Bioapplications

Application of photothermal effects of nanomaterials in food safety detection

Numerous nanomaterials endowed with outstanding light harvesting and photothermal conversion abilities have been extensively applied in various fields, such as photothermal diagnosis and therapy, trace substance detection, and optical imaging. Although photothermal detection methods have been established utilizing the photothermal effect of nanomaterials in recent years, there is a scarcity of reviews regarding their application in food safety detection. Herein, the recent advancements in the photothermal conversion mechanism, photothermal conversion efficiency calculation, and preparation method of photothermal nanomaterials were reviewed. In particular, the application of photothermal nanomaterials in various food hazard analyses and the newly established photothermal detection methods were comprehensively discussed. Moreover, the development and promising future trends of photothermal nanomaterial-based detection methods were discussed, which provide a reference for researchers to propose more effective, sensitive, and accurate detection methods.

Stimulus-Responsive Ultrathin Films for Bioapplications: A Concise Review

The term "nanosheets" has been coined recently to describe supported and free-standing "ultrathin film" materials, with thicknesses ranging from a single atomic layer to a few tens of nanometers. Owing to their physicochemical properties and their large surface area with abundant accessible active sites, nanosheets (NSHs) of inorganic materials such as Au, amorphous carbon, graphene, and boron nitride (BN) are considered ideal building blocks or scaffolds for a wide range of applications encompassing electronic and optical devices, membranes, drug delivery systems, and multimodal contrast agents, among others. A wide variety of synthetic methods are employed for the manufacturing of these NSHs, and they can be categorized into (1) top-down approaches involving exfoliation of layered materials, or (2) bottom-up approaches where crystal growth of nanocomposites takes place in a liquid or gas phase. Of note, polymer template liquid exfoliation (PTLE) methods are the most suitable as they lead to the fabrication of high-performance and stable hybrid NSHs and NSH composites with the appropriate quality, solubility, and properties. Moreover, PTLE methods allow for the production of stimulus-responsive NSHs, whose response is commonly driven by a favorable growth in the appropriate polymer chains onto one side of the NSHs, resulting in the ability of the NSHs to roll up to form nanoscrolls (NSCs), i.e., open tubular structures with tunable interlayer gaps between their walls. On the other hand, this review gives insight into the potential of the stimulus-responsive nanostructures for biosensing and controlled drug release systems, illustrating the last advances in the PTLE methods of synthesis of these nanostructures and their applications.

Simultaneous optical and magnetophoretic monitoring of DNA hybridization using superparamagnetic and plasmonic colloids

The detection and separation of small biomolecules from complex mixtures and the possibility of their recovering for further analyses have great benefits for the early diagnosis and prognosis of diseases. Developing simple, sensitive, and cost-effective tools that allow the rapid and accurate assembly and isolation of molecular biomarkers has the potential to improve both patient care and hospital logistic efficiency towards personalized and affordable treatments of diseases.In this work, we presenta method consisting ofUV-vis-spectroscopy assisted-magnetophoresis for the monitoring of DNA hybridization. For this purpose, a magnetic device generating 7.5 T/m uniform magnetic field gradient was designed and incorporated to a commercial spectrophotometer. Different batches of colloidal superparamagnetic particles (SMPs), with different elemental compositions, were functionalized with twenty-mer complementary oligonucleotides, TB1 and TB2. When the functionalized SMPs-TB1 and SMPs-TB2 are mixed and incubated, the hybridization process of TB1 and TB2 occurs resulting in the formation of colloidal aggregates. When brought under the magnetic field, depending on the magnetic strength (Γ) of the formed aggregates, they separate either faster or slower than the non-functionalized SMPs. The difference in magnetic separation time (Δt) is optically monitored by measuring the real time transparency of the suspension at specific wavelengths. The detection of aggregates at concentrations of 0.001% w/v was achieved, showing Δt ranging from 113-228 s. Based on the changes of Δt, the study addresses how electrosteric, magnetic, and hydrogen bonding interactions affect the hybridization process and suggests optimum experimental conditions for accurate monitoring of TB1-TB2 hybridization.

In vitro and in vivo biocompatibility and bio-tribological properties of the calcium/amorphous-C composite films for bone tissue engineering application

Carbon-and diamond-like-carbon coated Ti alloys hold great promise for tissue engineering applications. Unfortunately, their strong intrinsic stress leads to the adhesion failure of the films. Herein, a series of a-C films with different Ca content were prepared on Ti₆Al₄V via co-sputtering deposition technology. Homogeneous spherical Ca nanoclusters, with an inner diameter of 2-6 nm, were formed in an amorphous carbon matrix. The addition of Ca induced indistinctive variation in either phase composition or topography. However, the introduction of Ca not only improved the mechanical properties of a-C film but also significantly strengthened its adhesion to osteoblasts. The bio-tribological properties of Ca/a-C films were also assessed using a tribometer in FBS solution. The Ca/a-C films exhibited a low friction coefficient of 0.083 and a low wear rate of 1.02-1.24×10^-6 mm³/Nm. The low coefficient of friction (COF) of the Ca/a-C films indicates their superior mechanical properties, making them the promising target of nanocomposite films used in bio-tribological applications. Well-stretched cells and the developed actin filaments were distinctly observed on the Ca/a-C films in the osteoblast cell adhesion experiments. In addition, the Ca/a-C films promoted cell proliferation and showed high cell viability. After being implanted for 4 weeks, the Ca/a-C implant material still adhered well to the muscle tissue, without inducing hyperergic or inflammatory reactions. Collectively, our results suggest that the Ca/a-C film is an ideal mounting material for bone tissue engineering.

Functionalized acupuncture needle as a SERS-active platform for rapid and sensitive determination of adenosine triphosphate

The development of sensitive and rapid methods for analysis and detection of small molecules is highly desirable for medical diagnostics and therapeutics. We report an acupuncture needle functionalized with gold nanoparticles (Au NPs) and a macrocyclic amine (MA) Raman tag as the platform to realize the sensitive detection of adenosine triphosphate (ATP) by surface-enhanced Raman spectroscopy (SERS). The assembled Au NPs with abundant hot spots on the surface of the needle avoids the aggregation of Au NPs and results in a good signal response. Moreover, there is strong combination between ATP and MA through electrostatic adsorption, hydrogen-bonding interactions, and π-π stacking, and as a consequence, this functionalized needle can be used as a SERS platform for detection of ATP (25 nM) through a decrease of the Raman signal of MA resulting from the high chemical affinity of ATP for MA. Specially, the Au NP/MA-functionalized needle is conveniently used to monitor ATP (100 nM) added to serum, and demonstrates great promise in the study and detection of ATP in a complex sample, laying the foundation for SERS applications in complex acupuncture specimens with fast response and simple operation. Graphical abstract.

Carbon Nanoscrolls for Aluminum Battery

This design provides a scalable route for in situ synthesizing of special carbon nanoscrolls as the cathode for an aluminum battery. The frizzy architectures are generated by a few graphene layers convoluting into the hollow carbon scroll, possessing rapid electronic transportation channels, superior anion storage capability, and outstanding ability of accommodating a large volume expansion during the cycling process. The electrochemical performance of the carbon nanoscroll cathode is fully tapped, displaying an excellent reversible discharge capacity of 104 mAh g^-1 at 1000 mA g^-1. After 55 000 cycles, this cathode retains a superior reversible specific capacity of 101.24 mAh g^-1 at an ultrafast rate of 50 000 mA g^-1, around 100% of the initial capacity, which demonstrates a superior electrochemical performance. In addition, anionic storage capability and structural stability are discussed in detail. The battery capacity under a wide temperature range from -80 to 120 °C is examined. At a low temperature of -25 °C, the battery delivers a discharge capacity of 62.83 mAh g^-1 after 10 000 cycles, obtaining a capacity retention near 100%. In addition, it achieves a capacity of 99.5 mAh g^-1 after 4000 cycles at a high temperature of 80 °C, with a capacity retention close to 100%. The carbon nanoscrolls possess an outstanding ultrafast charging/variable discharging rate performance surpassing all the batteries previously reported, which are highly promising for being applied in energy storage fields.

Controlled fabrication of electrically contacted carbon nanoscrolls

Carbon nanoscrolls (CNS) with their open ended morphology have recently attracted interest due to the potential application in gas capture, biosensors and interconnects. However, CNS currently suffer from the same issue that have hindered widespread integration of CNTs in sensors and devices: formation is done ex situ, and the tubes have to be placed with precision and reliability-a difficult task with low yield. Here, we demonstrate controlled in situ formation of electrically contacted CNS from suspended graphene nanoribbons with slight tensile stress. Formation probability depends on the length to width aspect ratio. Van der Waals interaction between the overlapping layers fixes the nanoscroll once formed. The stability of these CNSs is investigated by helium nano ion beam assisted in situ cutting. The loose stubs remain rolled and mostly suspended unless subject to a moderate helium dose corresponding to a damage rate of 4%-20%. One CNS stub remaining perfectly straight even after touching the SiO₂ substrate allows estimation of the bending moment due to van der Waals force between the CNS and the substrate. The bending moment of 5400 eV is comparable to previous theoretical studies. The cut CNSs show long-term stability when not touching the substrate.