HgSe Self-Doped Nanocrystals as a Platform to Investigate the Effects of Vanishing Confinement

In-Synthesis Se-Stabilization Enables Defect and Doping Engineering of HgTe Colloidal Quantum Dots

Colloidal Quantum Dots (CQDs) of mercury telluride (HgTe) hold particular appeal for infrared photodetection due to their widely tunable infrared absorption and good compatibility with silicon electronics. While advances in surface chemistry have led to improved CQD solids, the chemical stability of HgTe material is not fully emphasized. In this study, it is aimed to address this issue and identifies a Se-stabilization strategy based on the surface coating of Se on HgTe CQDs via engineering in the precursor reactivity. The presence of Se-coating enables HgTe CQDs with improved colloidal stability, passivation, and enhanced degree of freedom in doping tuning. This enables the construction of optimized p-i-n HgTe CQD infrared photodetectors with an ultra-low dark current 3.26 × 10-6 A cm⁻2 at -0.4 V and room-temperature specific detectivity of 5.17 × 1011 Jones at wavelength ≈2 um, approximately one order of magnitude improvement compared to that of the control device. The stabilizing effect of Se is well preserved in the thin film state, contributing to much improved device stability. The in-synthesis Se-stabilization strategy highlights the importance of the chemical stability of materials for the construction of semiconductor-grade CQD solids and may have important implications for other high-performance CQD optoelectronic devices.

Model-Based Practically Precise Fabrication of HgSe Quantum Dots toward Their Application in a Long-Wave Infrared Micro Spectrometer

Quantum dot (QD) passive filters present a simple and low-cost strategy for the micromation of spectrometers. In this field, the consistency between ultranarrow band gap QD fabrication and the precise control of its absorption characteristics is the key-challenge to extend QD spectrometers into the long-wave infrared (LWIR) region. Here, we show the model-based, practically precise fabrication of HgSe QDs as well as their specific spectral responses. Both the theoretical and experimental models of the HgSe QDs r-λ are formulated, which reveals the variation of transmission spectrum with the size of HgSe QDs. Then, the HgSe QDs synthesis parameter-spectral response hyperplane model and neural network model were obtained by using traditional polynomial fitting and machine learning, respectively. We also demonstrate the model-based precise fabrication of HgSe QDs with transmission characteristic peaks within 14 μm. The further simulation also shows that the 255─element QD filter array has the signal-to-noise ratio up to 14.57 dB with detection resolution about 5 cm-1.

Infrared Imaging Using Thermally Stable HgTe/CdS Nanocrystals

Transferring nanocrystals (NCs) from the laboratory environment toward practical applications has raised new challenges. HgTe appears as the most spectrally tunable infrared colloidal platform. Its low-temperature synthesis reduces the growth energy cost yet also favors sintering. Once coupled to a read-out circuit, the Joule effect aggregates the particles, leading to a poorly defined optical edge and large dark current. Here, we demonstrate that CdS shells bring the expected thermal stability (no redshift upon annealing, reduced tendency to form amalgams, and preservation of photoconduction after an atomic layer deposition process). The electronic structure of these confined particles is unveiled using k.p self-consistent simulations showing a significant exciton binding energy of ∼200 meV. After shelling, the material displays a p-type behavior that favors the generation of photoconductive gain. The latter is then used to increase the external quantum efficiency of an infrared imager, which now reaches 40% while presenting long-term stability.

Microbial antagonistic mechanisms of Hg(II) and Se(IV) in efficient wastewater treatment using granular sludge

The antagonistic effects of mercury (Hg) and selenium (Se) have been extensively studied in higher animals and plants. In this study, the microbial antagonistic effects of Hg and Se were utilized for wastewater treatment. We developed and optimized a new granular sludge approach to efficiently remove Hg(II) and Se(IV) from wastewater. Under anaerobic-oxic-anaerobic (AOA) conditions, the removal rates of Hg(II) and Se(IV) reached up to 99.91±0.07 % and 97.7 ± 0.8 %, respectively. The wastewater Hg(II) was mostly (97.43±0.01 %) converted to an inert mineral called tiemannite (HgSe) in the sludge, and no methylmercury (MeHg) was detected. The HgSe in sludge is less toxic, with almost no risk of secondary release, and it can be recovered with high purity. An inhibition experiment of mercury reduction and the high expression of the mer operon indicated that most Hg(II) (∼71 %) was first reduced to Hg0, and then Hg0 reacted with Se0 to synthesize HgSe. Metagenomic results showed that the final sludge (day 182) was dominated by two unclassified bacteria in the orders Rhodospirillales (27.7 %) and Xanthomonadales (6.3 %). Their metagenome-assembled genomes (MAGs) were recovered, suggesting that both of them can reduce Hg(II) and Se(IV). Metatranscriptomic analyses indicate that they can independently and cooperatively synthesize HgSe. In summary, granular sludge under AOA conditions is an efficient method for removing and recovering Hg from wastewater. The microbial transformation of Hg2+to Hg0 to HgSe may occur widely in both engineering and natural ecosystems.

Ultranarrow Mid-infrared Quantum Plasmon Resonance of Self-Doped Silver Selenide Nanocrystal

The infrared quantum plasmon resonance (IR QPR) of nanocrystals (NCs) exhibits the combined properties of classical and quantum mechanics, potentially overcoming the limitations of conventional optical features. However, research on the development of localized surface plasmon resonance (LSPR) from colloidal quantum dots has stagnated, owing to the challenge of increasing the carrier density of semiconductor NCs. Herein, we present the mid-IR QPR of a self-doped Ag2Se NC with an exceptionally narrow bandwidth. Chemical modification of the NC surface with chloride realizes this narrow QPR bandwidth by achieving a high free-carrier density in the NC. The mid-IR QPR feature was thoroughly analyzed by using various experimental methods such as Fourier transform (FT) IR spectroscopy, X-ray photoelectron spectroscopy, and current-voltage measurements. In addition, the optical properties were theoretically analyzed using the plamon-in-a-box model and a modified hydrodynamic model that revealed the effect of coupling with the intraband transition and the limited nature of electron density in semiconductor NCs. Integrating the quantum effect into the plasmonic resonance reduces the peak bandwidth to 19.7 meV, which is an extremely narrow bandwidth compared with that of the LSPR of conventional metal oxide or metal chalcogenide NCs. Our results demonstrate that self-doped silver selenide quantum dots are excellent systems for studying mid-IR QPR.

Mercury chalcogenide colloidal quantum dots for infrared photodetection: from synthesis to device applications

Commercial infrared (IR) photodetectors based on epitaxial growth inorganic semiconductors, e.g. InGaAs and HgCdTe, suffer from high fabrication cost, poor compatibility with silicon integrated circuits, rigid substrates and bulky cooling systems, which leaves a large development window for the emerging solution-processable semiconductor-based photo-sensing devices. Among the solution-processable semiconductors, mercury (Hg) chalcogenide colloidal quantum dots (QDs) exhibit unique ultra-broad and tuneable photo-responses in the short-wave infrared to far-wave infrared range, and have demonstrated photo-sensing abilities comparable to the commercial products, especially with advances in high operation temperature. Here, we provide a focused review on photodetectors employing Hg chalcogenide colloidal QDs, with a comprehensive summary of the essential progress in the areas of synthesis methods of QDs, property control, device engineering, focus plane array integration, etc. Besides imaging demonstrations, a series of Hg chalcogenide QD photodetector based flexible, integrated, multi-functional applications are also summarized. This review shows prospects for the next-generation low-cost highly-sensitive and compact IR photodetectors based on solution-processable Hg chalcogenide colloidal QDs.

The Historical Development of Infrared Photodetection Based on Intraband Transitions

The infrared technology is entering widespread use as it starts fulfilling a growing number of emerging applications, such as smart buildings and automotive sectors. Majority of infrared photodetectors are based on interband transition, which is the energy gap between the valence band and the conduction band. As a result, infrared materials are mainly limited to semi-metal or ternary alloys with narrow-bandgap bulk semiconductors, whose fabrication is complex and expensive. Different from interband transition, intraband transition utilizing the energy gap inside the band allows for a wider choice of materials. In this paper, we mainly discuss the recent developments on intraband infrared photodetectors, including 'bottom to up' devices such as quantum well devices based on the molecular beam epitaxial approach, as well as 'up to bottom' devices such as colloidal quantum dot devices based on the chemical synthesis.

Vanishing Confinement Regime in Terahertz HgTe Nanocrystals Studied under Extreme Conditions of Temperature and Pressure

While HgTe nanocrystals (NCs) in the mid-infrared region have reached a high level of maturity, their far-infrared counterparts remain far less studied, raising the need for an in-depth investigation of the material before efficient device integration can be considered. Here, we explore the effect of temperature and pressure on the structural, spectroscopic, and transport properties of HgTe NCs displaying an intraband absorption at 10 THz. The temperature leads to a very weak modulation of the spectrum as opposed to what was observed for strongly confined HgTe NCs. HgTe NC films present ambipolar conduction with a clear prevalence of electron conduction as confirmed by transistor and thermoelectric measurements. Under the application of pressure, the material undergoes phase transitions from the zinc blende to cinnabar phase and later to the rock salt phase which we reveal using joint X-ray diffraction and infrared spectroscopy measurements. We discuss how the pressure existence domain of each phase is affected by the particle size.

Mid-Infrared Intraband Photodetector via High Carrier Mobility HgSe Colloidal Quantum Dots

In this work, a room-temperature mixed-phase ligand exchange method is developed to obtain a relatively high carrier mobility (∼1 cm²/(V s)) on HgSe intraband colloidal quantum dot solids without any observable trap state. What is more, the doping from 1S_e to 1P_e state in the conduction band could be precisely controlled by additional salts during this method, proved by optical and transport experiments. The high mobility and controllable doping benefit the mid-infrared photodetector utilizing the 1S_e to 1P_e transition, with a 1000-fold improvement in response speed, which is several μs, a 55-fold increase in responsivity, which is 77 mA/W, and a 10-fold increase in specific detectivity, which is above 1.7 × 10⁹ Jones at 80 K. The high-performance photodetector could serve as an intraband infrared camera for thermal imaging, as well as a CO₂ gas sensor with a range from 0.25 to 2000 ppm.

Mid-IR Intraband Photodetectors with Colloidal Quantum Dots

In this paper, we investigate an intraband mid-infrared photodetector based on HgSe colloidal quantum dots (CQDs). We study the size, absorption spectra, and carrier mobility of HgSe CQDs films. By regulating the time and temperature of the reaction during synthesis, we have achieved the regulation of CQDs size, and the number of electrons doped in conduction band. It is experimentally verified by the field effect transistor measurement that dark current is effectively reduced by a factor of 10 when the 1Se state is doped with two electrons compared with other doping densities. The HgSe CQDs film mobility is also measured as a function of temperature the HgSe CQDs thin film detector, which could be well fitted by Marcus Theory with a maximum of 0.046 ± 0.002 cm2/Vs at room temperature. Finally, we experimentally discuss the device performance such as photocurrent and responsivity. The responsivity reaches a maximum of 0.135 ± 0.012 A/W at liquid nitrogen temperature with a narrow band photocurrent spectrum.

Synthesis and low-order optical nonlinearities of colloidal HgSe quantum dots in the visible and near infrared ranges

We synthesize colloidal HgSe quantum dots and characterize their nonlinear refraction and nonlinear absorption using a Nd:YAG laser and its second harmonic. The 7.5 nm quantum dots were synthesized using the hot-injection method. The nonlinear absorption (β = 9×10^-7 cm W^-1) and negative nonlinear refraction (γ = -5×10^-12 cm² W^-1) coefficients of colloidal quantum dots were determined using the 10 ns, 532 nm laser radiation. The joint influence of above processes was realized at a higher intensity of probe pulses. In the case of 10 ns, 1064 nm radiation, only negative nonlinear refraction dominated during z-scans of these quantum dots. The studies of optical limiting using two laser sources demonstrated the effectiveness of this process at 532 nm. The role of nonlinear scattering is analyzed. We discuss the mechanisms responsible for the nonlinear refraction processes in colloidal HgSe quantum dots.

HgTe Nanocrystals for SWIR Detection and Their Integration up to the Focal Plane Array

Infrared applications remain too often a niche market due to their prohibitive cost. Nanocrystals offer an interesting alternative to reach cost disruption especially in the short-wave infrared (SWIR, λ < 1.7 μm) where material maturity is now high. Two families of materials are candidate for SWIR photoconduction: lead and mercury chalcogenides. Lead sulfide typically benefits from all the development made for a wider band gap such as the one made for solar cells, while HgTe takes advantage of the development relative to mid-wave infrared detectors. Here, we make a fair comparison of the two material detection properties in the SWIR and discuss the material stability. At such wavelengths, studies have been mostly focused on PbS rather than on HgTe, therefore we focus in the last part of the discussion on the effect of surface chemistry on the electronic spectrum of HgTe nanocrystals. We unveil that tuning the capping ligands is a viable strategy to adjust the material from the p-type to ambipolar. Finally, HgTe nanocrystals are integrated into multipixel devices to quantize spatial homogeneity and onto read-out circuits to obtain a fast and sensitive infrared laser beam profile.

A colloidal quantum dot infrared photodetector and its use for intraband detection

Wavefunction engineering using intraband transition is the most versatile strategy for the design of infrared devices. To date, this strategy is nevertheless limited to epitaxially grown semiconductors, which lead to prohibitive costs for many applications. Meanwhile, colloidal nanocrystals have gained a high level of maturity from a material perspective and now achieve a broad spectral tunability. Here, we demonstrate that the energy landscape of quantum well and quantum dot infrared photodetectors can be mimicked from a mixture of mercury selenide and mercury telluride nanocrystals. This metamaterial combines intraband absorption with enhanced transport properties (i.e. low dark current, fast time response and large thermal activation energy). We also integrate this material into a photodiode with the highest infrared detection performances reported for an intraband-based nanocrystal device. This work demonstrates that the concept of wavefunction engineering at the device scale can now be applied for the design of complex colloidal nanocrystal-based devices.

The field of wavefunction engineering using intraband transition to design infrared devices has been limited to epitaxially grown semiconductors. Here the authors demonstrate that a device with similar energy landscape can be obtained from a mixture of colloidal quantum dots made of HgTe and HgSe.

Colloidal quantum dots for thermal infrared sensing and imaging

Colloidal quantum dots provide a powerful materials platform to engineer optoelectronics devices, opening up new opportunities in the thermal infrared spectral regions where no other solution-processed material options exist. This mini-review collates recent research reports that push the technological envelope of colloidal quantum dot-based photodetectors toward mid- and long-wavelength infrared. We survey the synthesis and characterization of various thermal infrared colloidal quantum dots reported to date, discuss the basic theory of device operation, review the fabrication and measurement of photodetectors, and conclude with the future prospect of this emerging technology.

Road Map for Nanocrystal Based Infrared Photodetectors

Infrared (IR) sensors based on epitaxially grown semiconductors face two main challenges which are their prohibitive cost and the difficulty to rise the operating temperature. The quest for alternative technologies which will tackle these two difficulties requires the development of new IR active materials. Over the past decade, significant progresses have been achieved. In this perspective, we summarize the current state of the art relative to nanocrystal based IR sensing and stress the main materials, devices and industrial challenges which will have to be addressed over the 5 next years.

Wave-Function Engineering in HgSe/HgTe Colloidal Heterostructures To Enhance Mid-infrared Photoconductive Properties

The use of intraband transition is an interesting alternative path for the design of optically active complex colloidal materials in the mid-infrared range. However, so far, the performance obtained for photodetection based on intraband transition remains much smaller than the one relying on interband transition in narrow-band-gap materials operating at the same wavelength. New strategies have to be developed to make intraband materials more effective. Here, we propose growing a heterostructure of HgSe/HgTe as a means of achieving enhanced intraband-based photoconduction. We first tackle the synthetic challenge of growing a heterostructure on soft (Hg-based) material. The electronic spectrum of the grown heterostructure is then investigated using a combination of numerical simulation, infrared spectroscopy, transport measurement, and photoemission. We report a type-II band alignment with reduced doping compared with a core-only object and boosted hole conduction. Finally, we probe the photoconductive properties of the heterostructure while resonantly exciting the intraband transition by using a high-power-density quantum cascade laser. Compared to the previous generation of material based on core-only HgSe, the heterostructures have a lower dark current, stronger temperature dependence, faster photoresponse (with a time response below 50 μs), and detectivity increased by a factor of 30.