Lignin Particles for Multifunctional Membranes, Antioxidative Microfiltration, Patterning, and 3D Structuring

Synthesis and Antibacterial Properties of Novel Quaternary Ammonium Lignins

The ongoing demand for effective antimicrobial materials persists, and lignin emerges as a promising natural antibacterial material with renewable properties. The adaptability of lignin to various chemical modifications offers avenues to enhance its antimicrobial activity. Here, we employed chloromethylation and subsequent functionalization with variable tertiary N-alkyl dimethyl amines to produce C6-C18 quaternary ammonium lignins (QALs) from hardwood (aspen), softwood (pine), and grass (barley straw). Successful synthesis of QALs was confirmed through NMR and FTIR analysis results along with an increase in the surface ζ-potential. Antibacterial activity of QALs against clinical strains of Klebsiella pneumoniae and methicillin-resistant Staphylococcus aureus was assessed using minimal bactericidal concentration (MBC) assay and agar growth inhibition zone (ZOI) test. The antibacterial activity of QALs was found to be higher than that of the unmodified lignins. QALs with longer alkyl chains demonstrated an MBC of 0.012 mg/L against K. pneumoniae already after 1 h of exposure with similar effect size reached after 24 h for S. aureus. For all the lignins, an increase in alkyl chain length resulted in an increase in their bactericidal activity. MBC values of C14-C18 QALs were consistently lower than the MBC values of QALs with shorter alkyl chains. Besides the alkyl chain length, MBC values of barley and pine QALs were negatively correlated with the surface ζ-potential. While alkyl chain length was one of the key properties affecting the MBC values in a liquid-based test, the agar-based ZOI test demonstrated an antibacterial optimum of QALs at C12-C14, likely due to limited diffusion of QALs with longer alkyl chains in a semisolid medium.

Overcoming Challenges of Lignin Nanoparticles: Expanding Opportunities for Scalable and Multifunctional Nanomaterials

ConspectusThe increasing demand for polymeric materials derived from petroleum resources, along with rising concerns about climate change and global plastic pollution, has driven the development of biobased polymeric materials. Lignin, which is the second most abundant biomacromolecule after cellulose, represents a promising renewable raw material source for the preparation of advanced materials. The lucrative properties of lignin include its high carbon content (>60 atom %), high thermal stability, biodegradability, antioxidant activity, absorbance of ultraviolet radiation, and slower biodegradability compared to other wood components. Moreover, the advent of lignin nanoparticles (LNPs) over the last ten years has circumvented many well-known shortcomings of technical lignins, such as heterogeneity and poor compatibility with polymers, thereby unlocking the great potential of lignin for the development of advanced functional materials.LNPs stand out owing to their well-defined spherical shape and excellent colloidal stability, which is due to the electrostatic repulsion forces of carboxylic acid and phenolic hydroxyl groups enriched on their surface. These forces prevent their aggregation in aqueous dispersions (pH 3-9) and provide a high surface area to mass ratio that has been exploited to adsorb positively charged compounds such as enzymes or polymers. Consequently, it is not surprising that LNPs have become a prominent player in applied research in areas such as biocatalysis and polymeric composites, among others. However, like all ventures of life, LNPs also face certain challenges that limit their potential end-uses. Solvent instability remains the most challenging aspect due to the tendency of these particles to dissolve or aggregate in organic solvents and basic or acidic pH, thus limiting the window for their chemical functionalization and applications. In addition, the need for organic solvent during their preparation, the poor miscibility with hydrophobic polymeric matrices, and the nascent phase regarding their use in smart materials have been identified as important challenges that need to be addressed.In this Account, we recapitulate our efforts over the past years to overcome the main limitations mentioned above. We begin with a brief introduction to the fundamentals of LNPs and a detailed discussion of their associated challenges. We then highlight our work on: (i) Preparation of lignin-based nanocomposites with improved properties through a controlled dispersion of LNPs within a hydrophobic polymeric matrix, (ii) Stabilization of LNPs via covalent (intraparticle cross-linking) and noncovalent (hydration barrier) approaches, (iii) The development of an organic-solvent-free method for the production of LNPs, and (iv) The development of LNPs toward smart materials with high lignin content. Finally, we also offer our perspectives on this rapidly growing field.

Spray Coating of Wood with Nanoparticles from Lignin and Polylactic Glycolic Acid Loaded with Thyme Essential Oils

Ensuring the longevity of wooden constructions depends heavily on the preservation process. However, several traditional preservation methods involving fossil-based compounds have become outdated because they pose a significant risk to the environment and to human health. Therefore, the use of bio-based and bioactive solutions, such as essential oils, has emerged as a more sustainable alternative in protecting wood from biotic attacks. The entrapment of essential oils in polymeric carrier matrices provides protection against oxidation and subsequent degradation or rapid evaporation, which implies the loss of their biocidal effect. In this work, lignin as well as PLGA nanoparticles containing the essential oils from two different thyme species (Thymus capitatus and T. vulgaris) were applied on beech wood samples using spray coating. The prepared coatings were investigated using FTIR imaging, SEM, as well as LSM analysis. Release experiments were conducted to investigate the release behavior of the essential oils from their respective lignin and PLGA carrier materials. The study found that lignin nanoparticles were more effective at trapping and retaining essential oils than PLGA nanoparticles, despite having larger average particle diameters and a more uneven particle size distribution. An analysis of the lignin coatings showed that they formed a uniform layer that covered most of the surface pores. PLGA nanoparticles formed a film-like layer on the cell walls, and after leaching, larger areas of native wood were evident on the wood samples treated with PLGA NPs compared to the ones coated with lignin NPs. The loading capacity and efficiency varied with the type of essential oil, while the release behaviors were similar between the two essential oil types applied in this study.

Lignin beyond the status quo: recent and emerging composite applications

The demand for biodegradable materials across various industries has recently surged due to environmental concerns and the need for the adoption of renewable materials. In this context, lignin has emerged as a promising alternative, garnering significant attention as a biogenic resource that endows functional properties. This is primarily ascribed to its remarkable origin and structure that explains lignin's capacity to bind other molecules, reinforce composites, act as an antioxidant, and endow antimicrobial effects. This review summarizes recent advances in lignin-based composites, with particular emphasis on innovative methods for modifying lignin into micro and nanostructures and evaluating their functional contribution. Indeed, lignin-based composites can be tailored to have superior physicomechanical characteristics, biodegradability, and surface properties, thereby making them suitable for applications beyond the typical, for instance, in ecofriendly adhesives and advanced barrier technologies. Herein, we provide a comprehensive overview of the latest progress in the field of lignin utilization in emerging composite materials.

Fabrication of transparent cellulose nanofibril composite film with smooth surface and ultraviolet blocking ability using hydrophilic lignin

Ecofriendly multifunctional films with only biomass-based components have gathered significant interest from researchers as next-generation materials. Following this trend, a TEMPO-oxidized cellulose nanofibril (TOCNF) film containing hydrophilic lignin (CL) was fabricated. To produce the lignin, peracetic acid oxidation was carried out, leading to the introduction of carboxyl groups into the lignin structure. By adding hydrophilic lignin, various characteristics (e.g., surface smoothness, UV protection, antimicrobial activity, and barrier properties) of the TOCNF film were enhanced. In particular, the shrinkage of CNF was successfully prevented by the addition of CL, which is attributed to the lower surface roughness (Ra) from 18.93 nm to 4.99 nm. As a result, the smooth surface of the TOCNF/CL film was shown compared to neat TOCNF film and TOCNF/Kraft lignin composite film. In addition, the TOCNF/CL film showed a superior UV blocking ability of 99.9 % with high transparency of 78.4 %, which is higher than that of CNF-lignin composite films in other research. Also, water vapor transmission rate was reduced after adding CL to TOCNF film. Consequently, the developed TOCNF/CL film can be potentially utilized in various applications, such as food packaging.

Multifunctional Bacterial Cellulose Films Enabled by Deep Eutectic Solvent-Extracted Lignin

Inspired by natural plant cells, lignin is utilized as a filler and a functional agent to modify bacterial cellulose (BC). By mimicking the lignin-carbohydrate structure, deep eutectic solvent (DES)-extracted lignin serves as a glue to strength the BC films and endows the films with diverse functionality. The lignin isolated by the DES (formed by choline chloride and lactic acid) is rich in phenol hydroxyl groups (5.5 mmol/g) and exhibits a narrow molecular weight distribution. A good interface compatibility can be obtained in the composite film, and lignin fills the void/gaps between BC fibrils. The integration of lignin endows the films with enhanced water-proof, mechanical, UV shielding, gas barrier, and antioxidant abilities. The BC/lignin composite film with 0.4 g of lignin addition (BL-0.4) exhibits an oxygen permeability and a water vapor transmission rate of 0.4 mL/m²/day/Pa and 0.9 g/m²/day, respectively. The multifunctional films are promising candidates for packing materials and exhibit a broad application prospect in the field of petroleum-based polymer replacement.

Pickering Emulsions Stabilized by Lignin/Chitosan Nanoparticles for Biphasic Enzyme Catalysis

In this study, we construct a green and high-performance platform using Pickering emulsions for biphasic catalysis. The oil-in-water Pickering emulsions stabilized by the lignin/chitosan nanoparticles (Lig/Chi NPs) have great stability and alkali resistance, showing pH-responsive reversible emulsification and demulsification which can be recycled at least three times. The Pickering emulsion also has fluorescence and wide availability to different oil-to-water volume ratios, types of oil, storage times, temperatures, and ion concentrations. When this system is applied to the lipase-catalyzed reaction for the hydrolysis of p-nitrophenol palmitate, it will provide stable and large oil-water reaction interface areas, and the negatively charged lipase will enrich at the emulsion interface by electrostatic adsorption of the positively charged Lig/Chi NPs to achieve immobilization (lipase-Lig/Chi NPs). The reaction conversion rate can reach nearly 100% in 30 min, which is nearly three times higher than that of the conventional two-phase system. Moreover, the lipases in Pickering emulsion stabilized by Lig/Chi NPs exhibit great recyclability because of the protection of Lig/Chi NPs.

From residue to resource: new insights into the synthesis of functionalized lignin micro/nanospheres by self-assembly technology for waste resource utilization

Among the most abundant biopolymers in the biosphere, lignin is a renewable aromatic compound that represents an untapped opportunity to create new biological products. However, the complex interlacing structures of cellulose, hemicellulose and lignin, as well as the unique properties of lignin, limit the utilization of value-added lignin. Lignin-based nanomaterials open the door for lignin applications in environmental pollutant remediation, biofuel production, biomedicine, and other fields. Herein, we present various factors influencing the formation of micro-nanospheres by self-assembly techniques through a review of previous literature, and emphasize the simple and green synthesis of lignin micro/nanospheres (LMNPs) under non-modified conditions. More importantly, we discuss the mechanism of the formation of nanospheres. Considering the heterogeneity of lignin and the polarity of different solvents, we propose that self-assembly techniques should focus more on the influence brought by lignin itself or the solvent, so that the external conditions can be controlled to prepare LMNPs, which can be used in specific fields. A brief overview of the contribution of lignin-based nanomaterials in various fields is also presented. This review could provide insight for the development of lignin-based nanomaterials.

Room Temperature Fabrication of Macroporous Lignin Membranes for the Scalable Production of Black Silicon

Rising global demand for biodegradable materials and green sources of energy has brought attention to lignin. Herein, we report a method for manufacturing standalone lignin membranes without additives for the first time to date. We demonstrate a scalable method for macroporous (∼100 to 200 nm pores) lignin membrane production using four different organosolv lignin materials under a humid environment (>50% relative humidity) at ambient temperatures (∼20 °C). A range of different thicknesses is reported with densely porous films observed to form if the membrane thickness is below 100 nm. The fabricated membranes were readily used as a template for Ni²⁺ incorporation to produce a nickel oxide membrane after UV/ozone treatment. The resultant mask was etched via an inductively coupled plasma reactive ion etch process, forming a silicon membrane and as a result yielding black silicon (BSi) with a pore depth of >1 μm after 3 min with reflectance <3% in the visible light region. We anticipate that our lignin membrane methodology can be readily applied to various processes ranging from catalysis to sensing and adapted to large-scale manufacturing.

Deconstruction and Reassembly of Renewable Polymers and Biocolloids into Next Generation Structured Materials

This review considers the most recent developments in supramolecular and supraparticle structures obtained from natural, renewable biopolymers as well as their disassembly and reassembly into engineered materials. We introduce the main interactions that control bottom-up synthesis and top-down design at different length scales, highlighting the promise of natural biopolymers and associated building blocks. The latter have become main actors in the recent surge of the scientific and patent literature related to the subject. Such developments make prominent use of multicomponent and hierarchical polymeric assemblies and structures that contain polysaccharides (cellulose, chitin, and others), polyphenols (lignins, tannins), and proteins (soy, whey, silk, and other proteins). We offer a comprehensive discussion about the interactions that exist in their native architectures (including multicomponent and composite forms), the chemical modification of polysaccharides and their deconstruction into high axial aspect nanofibers and nanorods. We reflect on the availability and suitability of the latter types of building blocks to enable superstructures and colloidal associations. As far as processing, we describe the most relevant transitions, from the solution to the gel state and the routes that can be used to arrive to consolidated materials with prescribed properties. We highlight the implementation of supramolecular and superstructures in different technological fields that exploit the synergies exhibited by renewable polymers and biocolloids integrated in structured materials.

Culturing rhodotorula glutinis in fermentation-friendly deep eutectic solvent extraction liquor of lignin for producing microbial lipid

Currently, deep eutectic solvents (DES) have attracted increasing attention due to their excellent performance in delignification. However, few studies focused on the treatment of DES waste liquid after extraction of lignin. In this work, the fermentation-friendly DES comprised of glycerol, choline chloride (ChCl) and acetic acid (AA) was applied for delignification of lignocellulose. Subsequently, the extraction effects of different DES were investigated, and the DES extraction liquor was used for lipid production. Results shows ChCl made little difference to lipid synthesis, while excessive AA exerted inhibitory effect on the growth of cells. Following pretreatment, the delignification exceeded 63%. When the DES liquid obtained after lignin extraction was used to produce lipid, the delay period was obvious, while the lipid yield and content were unaffected. Not only is the DES prepared in this study effective in delignification of lignocellulose, it is also applicable as raw material to produce lipid.

Multifunctional lignin-based nanocomposites and nanohybrids

Significant progress in lignins valorization and development of high-performance sustainable materials have been achieved in recent years. Reports related to lignin utilization indicate excellent prospects considering green chemistry, chemical engineering, energy, materials and polymer science, physical chemistry, biochemistry, among others. To fully realize such potential, one of the most promising routes involves lignin uses in nanocomposites and nanohybrid assemblies, where synergistic interactions are highly beneficial. This review first discusses the interfacial assembly of lignins with polysaccharides, proteins and other biopolymers, for instance, in the synthesis of nanocomposites. To give a wide perspective, we consider the subject of hybridization with metal and metal oxide nanoparticles, as well as uses as precursor of carbon materials and the assembly with other biobased nanoparticles, for instance to form nanohybrids. We provide cues to understand the fundamental aspects related to lignins, their self-assembly and supramolecular organization, all of which are critical in nanocomposites and nanohybrids. We highlight the possibilities of lignin in the fields of flame retardancy, food packaging, plant protection, electroactive materials, energy storage and health sciences. The most recent outcomes are evaluated given the importance of lignin extraction, within established and emerging biorefineries. We consider the benefit of lignin compared to synthetic counterparts. Bridging the gap between fundamental and application-driven research, this account offers critical insights as far as the potential of lignin as one of the frontrunners in the uptake of bioeconomy concepts and its application in value-added products.

Unravelling the Hydration Barrier of Lignin Oleate Nanoparticles for Acid- and Base-Catalyzed Functionalization in Dispersion State

Lignin nanoparticles (LNPs) are promising renewable nanomaterials with applications ranging from biomedicine to water purification. However, the instability of LNPs under acidic and basic conditions severely limits their functionalization for improved performance. Here, we show that controlling the degree of esterification can significantly improve the stability of lignin oleate nanoparticles (OLNPs) in acidic and basic aqueous dispersions. The high stability of OLNPs is attributed to the alkyl chains accumulated in the shell of the particle, which delays protonation/deprotonation of carboxylic acid and phenolic hydroxyl groups. Owing to the enhanced stability, acid‐ and base‐catalyzed functionalization of OLNPs at pH 2.0 and pH 12.0 via oxirane ring‐opening reactions were successfully performed. We also demonstrated these new functionalized particles as efficient pH‐switchable dye adsorbents and anticorrosive particulate coatings.

Enhancing the Radical Scavenging Activity and UV Resistance of Lignin Nanoparticles via Surface Mannich Amination toward a Biobased Antioxidant

In recent years, lignin specific activities, such as antioxidation and antibacterial and anti-ultraviolet performance, have drawn more and more attention. Nevertheless, the insufficient radical scavenging (antioxidation) activity has become one of the main drawbacks that limits its high-value application. In this study, lignin nanoparticles (LNPs) were prepared via a facile acid treatment strategy. Subsequently, surface amination of LNPs (a-LNPs) was carried out through the Mannich reaction. Specifically, the antioxidant behavior of LNPs and modified LNPs was evaluated by DPPH/DMPO radical scavenging and in vitro HeLa cell reactive oxygen species (ROS) scavenging tests, which demonstrated that the antioxidation activity of a-LNPs was more evident than that of both LNPs and butylated hydroxytoluene (BHT) commercial antioxidant. The mechanism of the radical scavenging ability of aminated LNPs was elucidated and proved to be related to the bond dissociation enthalpy of Ar-O···H, determined by the electron-donating effect of the substituted groups in the ortho-position. Meanwhile, the morphologies, solubilities, and UV-absorbing and antibacterial behavior of LNPs and a-LNPs were also studied, and the results showed that a-LNP sample exhibited higher UV resistance performance than LNPs. We expected that the modified LNPs with high antioxidation activity can serve as a safe and lower-cost biobased antioxidant.

Insight into the Surface Properties of Wood Fiber-Polymer Composites

The surface properties of wood fiber (WF) filled polymer composites depend on the filler loading and are closely related to the distribution and orientation in the polymer matrix. In this study, wood fibers (WF) were incorporated into thermoplastic composites based on non-recycled polypropylene (PP) and recycled (R-PP) composites by melt compounding and injection moulding. ATR-FTIR (attenuated total reflection Fourier transform infrared spectroscopy) measurements clearly showed the propagation of WF functional groups at the surface layer of WF-PP/WF-R-PP composites preferentially with WF loading up to 30%. Optical microscopy and nanoindentation method confirmed the alignment of thinner skin layer of WF-PP/WF-R-PP composites with increasing WF addition. The thickness of the skin layer was mainly influenced by the WF loading. The effect of the addition of WF on modulus and hardness, at least at 30 and 40 wt.%, varies for PP and R-PP matrix. On the other hand, surface zeta potential measurements show increased hydrophilicity with increasing amounts of WF. Moreover, WF in PP/R-PP matrix is also responsible for the antioxidant properties of these composites as measured by DPPH (2,2′-diphenyl-1-picrylhydrazyl) assay.

State-of-the-Art: Applications and Industrialization of Lignin Micro/Nano Particles

As a new product of high-value utilization of lignin, lignin micro/nano particles (LMNPs) have attracted the attention of researchers due to their non-toxicity, corrosion-resistance, UV resistance, and other excellent characteristics and potential application value. This article outlined the main preparation methods of LMNPs at the current stage, summarized and compared them from three perspectives of preparation technology, final product state and product composition. Subsequently, based on the different focuses of the properties of LMNPs, their application research progress as fillers, UV blockers, drug delivery carriers, among others, were introduced. Then a concise analysis of the technical and economic assessment and life cycle assessment of LMNPs in the process of industrialization was made. Finally, the main problems at present and the future development directions were analyzed and prospected to provide references for the deep processing of forest resources and the development of bio-based nanomaterials.

Lignin Nanoparticle Nucleation and Growth on Cellulose and Chitin Nanofibers

Cellulose (CNF) and chitin (ChNF) nanofibers are known to form materials that are both tough and strong. In this study, we hypothesize that the inertness of networks produced from CNF and ChNF makes them ideal templates for heterogeneous reactions and in situ formation of nanoarchitectures. We expand nanoparticle templating on polysaccharide colloids by introducing a new and facile process that leads to the growth of organic nanoparticles on CNF and ChNF in aqueous media. The process, based on solvent shifting supported on solid interfaces, is demonstrated by direct observation of lignin nanoparticles that are further used for their photocatalytic activity. Importantly, the dynamics of nanoparticle nucleation and growth is correlated with the surface chemistry of the templating nanopolysaccharides. Electrostatic repulsion between the deprotonated lignin molecules and the slightly negative CNF support led to limited adsorption and was effective in producing free (nonbound) lignin nanoparticles (28 ± 7 nm) via precipitation. In contrast, the stronger interfacial interactions between the positively charged ChNF and lignin molecules facilitated instantaneous and extensive lignin adsorption, followed by nucleation and growth into relatively larger nanoparticles (46 ± 17 nm). The latter were homogeneously distributed and strongly coupled to the ChNF support. Overall, we introduce lignin nanoparticle nucleation and growth on renewable nanopolysaccharides, offering an effective route toward in situ synthesis of highly functional fibrils and related cohesive films that offer a great potential in packaging and other applications.

Residual lignin in cellulose nanofibrils enhances the interfacial stabilization of Pickering emulsions

Lignocellulose nanofibrils (LCNF) were used to prepare oil-in-water Pickering emulsions and to assess the role residual lignin in interfacial stabilization. Two LCNF fractions of similar morphology (length ∼700 nm and width ∼8 nm) and structure (polymorphism and crystallinity) were obtained by microfluidization of fibers obtained by hydrothermal treatment of wood with a recyclable organic acid. The LCNF with higher residual lignin was less hydrophilic and, correspondingly, performed better as Pickering stabilizer, producing emulsions of smaller droplet size and higher resistance to creaming. Long-term emulsion stabilization (over 40 days) was achieved with LCNF at concentrations as low as 0.24 (w/v)% based on emulsion volume. We conclude that LCNF-stabilized Pickering emulsions can be finely tuned by varying the residual lignin content, providing a rationale for LCNF selection according to lignin type and concentration as variables affecting stabilization. Complementary considerations include the possible benefits of the residual lignin in LCNF, including antioxidant and UV absorption properties.

Three-Dimensional Printed Cell Culture Model Based on Spherical Colloidal Lignin Particles and Cellulose Nanofibril-Alginate Hydrogel

Three-dimensional (3D) printing has been an emerging technique to fabricate precise scaffolds for biomedical applications. Cellulose nanofibril (CNF) hydrogels have attracted considerable attention as a material for 3D printing because of their shear-thinning properties. Combining cellulose nanofibril hydrogels with alginate is an effective method to enable cross-linking of the printed scaffolds in the presence of Ca²⁺ ions. In this work, spherical colloidal lignin particles (CLPs, also known as spherical lignin nanoparticles) were used to prepare CNF-alginate-CLP nanocomposite scaffolds. High-resolution images obtained by atomic force microscopy (AFM) showed that CLPs were homogeneously mixed with the CNF hydrogel. CLPs brought antioxidant properties to the CNF-alginate-CLP scaffolds in a concentration-dependent manner and increased the viscosity of the hydrogels at a low shear rate, which correspondingly provide better shape fidelity and printing resolution to the scaffolds. Interestingly, the CLPs did not affect the viscosity at high shear rates, showing that the shear thinning behavior typical for CNF hydrogels was retained, enabling easy printing. The CNF-alginate-CLP scaffolds demonstrated shape stability after printing, cross-linking, and storage in Dulbecco's phosphate buffer solution (DPBS +) containing Ca²⁺ and Mg²⁺ ions, up to 7 days. The 3D-printed scaffolds showed relative rehydration ratio values above 80% after freeze-drying, demonstrating a high water-retaining capability. Cell viability tests using hepatocellular carcinoma cell line HepG2 showed no negative effect of CLPs on cell proliferation. Fluorescence microscopy indicated that HepG2 cells grew not only on the surfaces but also inside the porous scaffolds. Overall, our results demonstrate that nanocomposite CNF-alginate-CLP scaffolds have high potential in soft-tissue engineering and regenerative-medicine applications.

Three-Dimensional Printed Cell Culture Model Based on Spherical Colloidal Lignin Particles and Cellulose Nanofibril-Alginate Hydrogel

Three-dimensional (3D) printing has been an emerging technique to fabricate precise scaffolds for biomedical applications. Cellulose nanofibril (CNF) hydrogels have attracted considerable attention as a material for 3D printing because of their shear-thinning properties. Combining cellulose nanofibril hydrogels with alginate is an effective method to enable cross-linking of the printed scaffolds in the presence of Ca2+ ions. In this work, spherical colloidal lignin particles (CLPs, also known as spherical lignin nanoparticles) were used to prepare CNF-alginate-CLP nanocomposite scaffolds. High-resolution images obtained by atomic force microscopy (AFM) showed that CLPs were homogeneously mixed with the CNF hydrogel. CLPs brought antioxidant properties to the CNF-alginate-CLP scaffolds in a concentration-dependent manner and increased the viscosity of the hydrogels at a low shear rate, which correspondingly provide better shape fidelity and printing resolution to the scaffolds. Interestingly, the CLPs did not affect the viscosity at high shear rates, showing that the shear thinning behavior typical for CNF hydrogels was retained, enabling easy printing. The CNF-alginate-CLP scaffolds demonstrated shape stability after printing, cross-linking, and storage in Dulbecco's phosphate buffer solution (DPBS +) containing Ca2+ and Mg2+ ions, up to 7 days. The 3D-printed scaffolds showed relative rehydration ratio values above 80% after freeze-drying, demonstrating a high water-retaining capability. Cell viability tests using hepatocellular carcinoma cell line HepG2 showed no negative effect of CLPs on cell proliferation. Fluorescence microscopy indicated that HepG2 cells grew not only on the surfaces but also inside the porous scaffolds. Overall, our results demonstrate that nanocomposite CNF-alginate-CLP scaffolds have high potential in soft-tissue engineering and regenerative-medicine applications.