Adsorption of lead(II) on O₂-plasma-oxidized multiwalled carbon nanotubes: thermodynamics, kinetics, and desorption

Enhanced Dye Adsorption on Cold Plasma-Oxidized Multi-Walled Carbon Nanotubes: A Comparative Study

The oxidation of multi-walled carbon nanotubes (MWCNTs) using cold plasma was investigated for their subsequent use as adsorbents for the removal of dyes from aqueous solutions. The properties of MWCNTs after plasma modification and their adsorption capacities were compared with pristine and chemically oxidized nanotubes. The modification process employed a reactor where plasma was generated through dielectric barrier discharges (DBD) powered by high-voltage nanosecond pulses. Various modification conditions were examined, such as processing time and pulse voltage amplitude. The degree of oxidation and the impact on the chemistry and structure of the nanotubes was investigated through various physicochemical and morphological characterization techniques (XPS, BET, TEM, etc.). Maximum oxidation (O/C = 0.09 from O/C = 0.02 for pristine MWCNTs) was achieved after 60 min of nanopulsed-DBD plasma treatment. Subsequently, the modified nanotubes were used as adsorbents for the removal of the dye methylene blue (MB) from water. The adsorption experiments examined the effects of contact time between the adsorbent and MB, as well as the initial dye concentration in water. The plasma-modified nanotubes exhibited high MB removal efficiency, with adsorption capacity proportional to the degree of oxidation. Notably, their adsorption capacity significantly increased compared to both pristine and chemically oxidized MWCNTs (~54% and ~9%, respectively). Finally, the kinetics and mechanism of the adsorption process were studied, with experimental data fitting well to the pseudo-second-order kinetic model and the Langmuir isotherm model. This study underscores the potential of plasma technology as a low-cost and environmentally friendly approach for material modification and water purification.

Transforming crystal structures of cobalt molybdate to generate electron-rich sites for electrochemical detection of Pb(II)

BACKGROUND

Most of the investigations on distinct crystal structures of catalysts are individually focused on the difference of surface functional groups or adsorption properties, but rarely explore the changes of active sites to affect the electrocatalytic performance. Catalysts with diverse crystal structures had been applied to modified electrodes in different electrocatalytic reactions. However, there is currently a lack of an essential understanding for the role of real active sites in catalysts with crystalline structures in electroanalysis, which is crucial for designing highly sensitive sensing interfaces.

RESULTS

Herein, cobalt molybdate with divergent crystal structures (α-CoMoO4 and β-CoMoO4) were synthesized by adjusting the calcination temperature, indicating that α-CoMoO4 (800 °C) (60.00 μA μM-1) had the highest catalytic ability than β-CoMoO4 (700 °C) (38.68 μA μM-1) and α-CoMoO4 (900 °C) (29.55 μA μM-1) for the catalysis of Pb(II). It was proved that the proportion of Co(II) and Mo(IV) as electron-rich sites in α-CoMoO4 (800 °C) were higher than β-CoMoO4 (700 °C) and α-CoMoO4 (900 °C), possessing more electrons to participate in the valence cycles of Co(II)/Co(III) and Mo(IV)/Mo(VI) to boost the catalytic reduction of Pb(II). Specifically, Co(II) transferred a part of electrons to Mo(VI), promoting the formation of Mo(IV). Co(II) and Mo(IV), as the electron-rich sites, providing electrons to Pb(II), further accelerating the conversion of Pb(II) into Pb(0).

SIGNIFICANCE

In the process of detecting Pb(II), the CoMoO4 structures under different temperatures have distinct content of electron-rich sites Co(II) and Mo(IV). α-CoMoO4 (800 °C), with the highest content are benefited to detect Pb(II). This work is conducive to understanding the effect of the changes of active sites resulting from crystal transformation on the electrocatalytic performance, and provides a way to construct sensitive electrochemical interfaces of distinct active sites.

Efficient adsorption of hexavalent chromium in water by torrefaction biochar from lignin-rich kiwifruit branches: The combination of experiment, 2D-COS and DFT calculation

A biochar (KBC) enriched with O functional groups was prepared by torrefaction using lignin-rich kiwifruit branches (KBM) as a raw material, which was characterized, and then KBC was used to adsorb hexavalent chromium (Cr6+) from water. The results showed that KBC contained more functional groups compared to KBM. The maximum adsorption of Cr6+ by KBC could reach 143.64 mg·g-1 and also had better adsorption performance than other adsorbents reported in some other reports. Cr6+ absorption by KBC was mainly a mechanism of electrostatic interaction and adsorption-reduction coupling. FTIR and XPS revealed that -OH, -COOH, CO and CC on KBC participated in Cr6+ adsorption and new groups (C=O) were generated during the process of adsorption, which implied that a redox reaction occurred. 2D-COS and DFT calculations showed that the order of functional groups on KBC interacting with Cr6+ was -OCH3 > -COOH > -OH > phenolic hydroxyl, and the binding tightness of the different functional groups to Cr6+ was -OCH3 (the shortest displacement of both groups after the adsorption) > -COOH > -OH > phenolic hydroxyl. KBC has good regeneration performance, and it is a good adsorbent for Cr6+.

A polylactic acid-carbon nanofiber-based electro-conductive sensing material and paper-based colorimetric sensor for detection of nitrates

Plastics are ubiquitous in today's lifestyle, and their indiscriminate use has led to the accumulation of plastic waste in landfills and oceans. The waste accumulates and breaks into micro-particles that enter the food chain, causing severe threats to human health, wildlife, and the ecosystem. Environment-friendly and bio-based degradable materials offer a sustainable alternative to the vastly used synthetic materials. Here, a polylactic acid and carbon nanofiber-based membrane and a paper-based colorimetric sensor have been developed. The membrane had a surface area of 3.02 m2 g-1 and a pore size of 18.77 nm. The pores were evenly distributed with a pore volume of 0.0137 cm3 g-1. The membrane was evaluated in accordance with OECD guidelines and was found to be safe for tested aquatic and terrestrial models. The activated PLA-CNF membrane was further used as a bio-based electrode for the electrochemical detection of nitrates (NO3-) in water samples with a detection limit of 0.046 ppm and sensitivity of 1.69 × 10-4 A ppm-1 mm-2, whereas the developed paper-based colorimetric sensor had a detection limit of 156 ppm for NO3-. This study presents an environment-friendly, low-carbon footprint disposable material for sensing applications as a sustainable alternative to plastics.

High-Performance Flexible Temperature Sensors Based on Laser-Irradiated Ag-MWCNTs/PEDOT:PSS

Recently, flexible temperature sensors have attracted significant interest due to their wide-ranging applications in areas such as biomedical monitoring, environmental monitoring, electronic skin, and intelligent robots. However, a combination of high sensitivity and high resolution remains a critical challenge. These properties depend on the synthesis techniques of the sensitive materials. In this work, we use a laser irradiation method to prepare a silver nanoparticle-modified carbon nanotube (Ag-MWCNT) which is further mixed with poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS). The developed temperature sensor exhibited a high sensitivity of -0.45% °C-1 and linearity with an R2 value of 0.998 in the temperature range of 25-80 °C. Additionally, the sensor demonstrated remarkable repeatability, making it suitable for real-time temperature monitoring of the human body and environment. This temperature sensor is successfully demonstrated in practical applications such as monitoring the temperature of various parts of the human body and sensing the spatial temperature. These demonstrations highlight their significant potential in electronic skin and other related fields.

A Study on the O2 Plasma Etching Method of Spray-Formed SWCNT Films and Their Utilization as Electrodes for Electrochemical Sensors

In this study, we analyzed the morphological changes and molecular structure changes on the surface of single-walled carbon nanotube (SWCNT) films during oxygen plasma (O2) etching of SWCNT surfaces formed by the spray method and analyzed their potential use as electrochemical electrodes. For this purpose, a SWCNT film was formed on the surface of a glass substrate using a self-made spray device using SWCNT powder prepared with DCB as a solvent, and SEM, AFM, and XPS analyses were performed as the SWCNT film was O2 plasma etched. SEM images and AFM measurements showed that the SWCNT film started etching after about 30 s under 50 W of O2 plasma irradiation and was completely etched after about 300 s. XPS analysis showed that as the O2 plasma etching of the SWCNT film progressed, the sp2 bonds representing the basic components of graphite decreased, the sp3 bonds representing defects increased, and the C-O, C=O, and COO peaks increased simultaneously. This result indicates that the SWCNT film was etched by the O2 plasma along with the oxygen species. In addition, electrochemical methods were used to verify the damage potential of the remaining SWCNTs after O2 plasma etching, including cyclic voltammetry, Randles plots, and EIS measurements. This resulted in a reversible response based on perfect diffusion control in the cyclic voltammetry, and an ideal linear curve in the Randles plot of the peak current versus square root scan rate curve. EIS measurements also confirmed that the charge transfer resistance of the remaining SWCNTs after O2 plasma etching is almost the same as before etching. These results indicate that the remaining SWCNTs after O2 plasma etching do not lose their unique electrochemical properties and can be utilized as electrodes for biosensors and electrochemical sensors. Our experimental results also indicate that the ionic conductivity enhancement by O2 plasma can be achieved additionally.

High adsorption performance for trace lead (II) cation from sewage by Fe/Cu metal organic nanosheets modified with terephthalic acid

A two-dimensional nanoflake (Fe/Cu-TPA) was prepared through a simple ultrasonic-centrifuge method. Fe/Cu-TPA has prominent performance on the removal of Pb²⁺ with low consistences. More than 99% lead (II) (Pb²⁺) was removed. The adsorption equipoise was established within 60 min for 50 mg L^-1 Pb²⁺. Fe/Cu-TPA shows excellent regenerability with 19.04% decline of Pb²⁺ adsorption competence in 5 cycles. There are two models for Fe/Cu-TPA adsorption of Pb²⁺, pseudo-second-order dynamic model and Langmuir isotherm model, with a utmost adsorption competence of 213.56 mg g^-1. This work offers a new candidate material for the industrial-grade Pb²⁺ adsorbents with promising application prospect.

Enhanced Catalytic Hydrodeoxygenation of Activated Carbon-Supported Metal Catalysts via Rapid Plasma Surface Functionalization

We employ a nonthermal, He/O₂ atmospheric plasma as an efficient surface functionalization method of activated carbons. We show that plasma treatment rapidly increases the surface oxygen content from 4.1 to 23.4% on a polymer-based spherical activated carbon in 10 min. Plasma treatment is 3 orders of magnitude faster than acidic oxidation and introduces a diverse range of carbonyl (C═O) and carboxyl (O-C═O) functionalities that were not found with acidic oxidation. The increased oxygen functionalities reduce the particle size of a high 20 wt % loading Cu catalyst by >44% and suppress the formation of large agglomerates. Increased metal dispersion exposes additional active sites and improves the yield of hydrodeoxygenation of 5-hydroxymethyl furfural to 2,5-dimethyl furan, an essential compound for biofuel replacement, by 47%. Surface functionalization via plasma can advance catalysis synthesis while being rapid and sustainable.

Chitosan-carbon nanofiber based disposable bioelectrode for electrochemical detection of oxytocin

Bioelectrodes with low carbon footprint can provide an innovative solution to the surmounting levels of e-waste. Biodegradable polymers offer green and sustainable alternatives to synthetic materials. Here, a chitosan-carbon nanofiber (CNF) based membrane has been developed and functionalized for electrochemical sensing application. The surface characterization of the membrane revealed crystalline structure with uniform particle distribution, and surface area of 25.52 m²/g and pore volume of 0.0233 cm³/g. The membrane was functionalized to develop a bioelectrode for the detection of exogenous oxytocin in milk. Electrochemical impedance spectroscopy was employed to determine oxytocin in a linear concentration range of 10 to 10⁵ ng/mL. The developed bioelectrode showed an LOD of 24.98 ± 11.37 pg/mL and sensitivity of 2.77 × 10^-10 Ω / log ng mL^-1/mm² for oxytocin in milk samples with 90.85-113.34 percent recovery. The chitosan-CNF membrane is ecologically safe and opens new avenues for environment-friendly disposable materials for sensing applications.

Efficient Removal of Pb2+ from Water by Bamboo-Derived Thin-Walled Hollow Ellipsoidal Carbon-Based Adsorbent

Lead ion (Pb²⁺) is one of the most common water pollutants. Herein, with bamboo as the raw material, we fabricate a thin-walled hollow ellipsoidal carbon-based adsorbent (CPCs900) containing abundant O-containing groups and carbon defects and having a specific surface area as large as 730.87 m² g^-1. CPCs900 shows a capacity of 37.26 mg g^-1 for adsorbing Pb²⁺ in water and an efficiency of 98.13% for removing Pb²⁺ from water. This is much better than the activated carbon commonly used for removing Pb²⁺ from water (12.19 mg g^-1, 30.48%). The bond interaction of Pb²⁺ with the O-containing groups on CPCs900 and the electrostatic interaction of Pb²⁺ with the electron-rich carbon defects on CPCs900 could be the main forces to drive Pb²⁺ adsorption on CPCs900. The outstanding adsorption performance of CPCs900 could be due to the abundant O-containing groups and carbon defects as well as the large specific surface area of CPCs900. Bamboo has a large reserve and a low price. The present work successfully converts bamboo into adsorbents with outstanding performances in removing Pb²⁺ from water. This is of great significance for meeting the huge industrial demand on highly efficient adsorbents for removing toxic metal ions from water.

Fabrication of 2D nanosheet sorbents through metastable emulsion droplets and subsequent two-step grafting polymerization for efficient blood lead removal in vitro

Hemoperfusion is a powerful and yet simple method for lead poisoning treatment, but creation of safe and effective sorbents with excellent selectivity remains a real challenge. To address this, we here construct 2D nanosheet sorbents (BM-SH) through metastable emulsion droplets and subsequent two-step grafting polymerization for efficient blood lead removal in vitro. Metastable emulsion droplets endow typical nanosized sheet-like structure (thickness of 30 nm) and relatively round shape. The consecutive two grafting processes using hydroxyethyl methacrylate (HEMA) and L-cysteine monomer (D-SH) provide BM-SH with a high density of accessible binding sites towards lead ions (Pb²⁺). A high adsorption capacity of 390.5 mg g^-1 and quick capture 97.35 % of Pb²⁺ within initial 10 min are obtained, surpassing most of the reported sorbents for lead removal. Besides, adsorption distribution coefficient (K_d) of BM-SH among four coexisting metal ions achieved 7792 mL g^-1, showing outstanding selectivity toward Pb²⁺. Importantly, a possible adsorption mechanism is recognized as coordination with carboxyl, sulfydryl and imino groups from L-cysteine, and mercapto ligand as the key chelating agent may be the reason for high Pb²⁺ affinity. And what's more, BM-SH displays good hemocompatibility and high efficiency of blood lead removal rate (above 86 % in vitro).

Heavy metal removal by biomass-derived carbon nanotubes as a greener environmental remediation: A comprehensive review

The concentrations of heavy metal ions found in waterways near industrial zones are often exceed the prescribed limits, posing a continued danger to the environment and public health. Therefore, greater attention has been devoted into finding the efficient solutions for adsorbing heavy metal ions. This review paper focuses on the synthesis of carbon nanotubes (CNTs) from biomass and their application in the removal of heavy metals from aqueous solutions. Techniques to produce CNTs, benefits of modification with various functional groups to enhance sorption uptake, effects of operating parameters, and adsorption mechanisms are reviewed. Adsorption occurs via physical adsorption, electrostatic interaction, surface complexation, and interaction between functional groups and heavy metal ions. Moreover, factors such as pH level, CNTs dosage, duration, temperature, ionic strength, and surface property of adsorbents have been identified as the common factors influencing the adsorption of heavy metals. The oxygenated functional groups initially present on the surface of the modified CNTs are responsible towards the adsorption enhancement of commonly-encountered heavy metals such as Pb²⁺, Cu²⁺, Cd²⁺, Co²⁺, Zn²⁺, Ni²⁺, Hg²⁺, and Cr⁶⁺. Despite the recent advances in the application of CNTs in environmental clean-up and pollution treatment have been demonstrated, major obstacles of CNTs such as high synthesis cost, the agglomeration in the post-treated solutions and the secondary pollution from chemicals in the surface modification, should be critically addressed in the future studies for successful large-scale applications of CNTs.

Adsorption Performance of Amino Functionalized Magnetic Molecular Sieve Adsorbent for Effective Removal of Lead Ion from Aqueous Solution

Lead ion (Pb²⁺) has high toxicity and brings great harm to human body. It is very important to find an effective method to address lead ion pollution. In this work, amino functionalized CoFe₂O₄/SBA–15 nanocomposite (NH₂–CoFe₂O₄/SBA–15) was prepared for the effective removal of Pb²⁺ from aqueous solution. The prepared NH₂–CoFe₂O₄/SBA–15 adsorbent was manifested by using scanning electron microscope (SEM), energy dispersive spectroscopy (EDS), Fourier transform infrared spectrum (FTIR), X-ray powder diffraction (XRD), and Brunauer-Emmett-Teller (BET) analysis. In the meantime, the adsorption conditions, including pH, adsorbent dosage, and adsorption time, were studied. The investigation of adsorption kinetics revealed that the adsorption results conform to the pseudo-first-order kinetic model. The adsorption isotherms research displayed that the adsorption was consistent with the Freundlich model, demonstrating that the adsorption for Pb²⁺ with the prepared adsorbent was a multimolecular layer adsorption process. In addition, the thermodynamic investigations (ΔG < 0, ΔH > 0, ΔS > 0) demonstrated that the adsorption for Pb²⁺ with the prepared adsorbent was endothermic and spontaneous. Moreover, the prepared adsorbent showed superior anti-interference performance and reusability, implying the potential application of the adsorbent in actual water treatment. Furthermore, this research may provide a reference and basis for the study of other heavy metal ions.

Functionalized Carbon Nanotubes (CNTs) for Water and Wastewater Treatment: Preparation to Application

As the world human population and industrialization keep growing, the water availability issue has forced scientists, engineers, and legislators of water supply industries to better manage water resources. Pollutant removals from wastewaters are crucial to ensure qualities of available water resources (including natural water bodies or reclaimed waters). Diverse techniques have been developed to deal with water quality concerns. Carbon based nanomaterials, especially carbon nanotubes (CNTs) with their high specific surface area and associated adsorption sites, have drawn a special focus in environmental applications, especially water and wastewater treatment. This critical review summarizes recent developments and adsorption behaviors of CNTs used to remove organics or heavy metal ions from contaminated waters via adsorption and inactivation of biological species associated with CNTs. Foci include CNTs synthesis, purification, and surface modifications or functionalization, followed by their characterization methods and the effect of water chemistry on adsorption capacities and removal mechanisms. Functionalized CNTs have been proven to be promising nanomaterials for the decontamination of waters due to their high adsorption capacity. However, most of the functional CNT applications are limited to lab-scale experiments only. Feasibility of their large-scale/industrial applications with cost-effective ways of synthesis and assessments of their toxicity with better simulating adsorption mechanisms still need to be studied.

RETRACTED: Preparation of molecularly imprinted metal-organic frameworks by in situ self-assembly template strategy for selective adsorption of antibiotics

This article has been retracted: please see Elsevier Policy on Article Withdrawal ( https://www.elsevier.com/about/our-business/policies/article-withdrawal). This article has been retracted at the request of the Authors. The corresponding author informed the journal that there were severe problems with the testing instrument that rendered the subsequent conclusions invalid. The authors apologise for any inconvenience caused.

Adsorption of methylene blue onto betel nut husk-based activated carbon prepared by sodium hydroxide activation process

In this study, activated carbon (AC) was prepared from agro-waste betel nut husks (BNH) through the chemical activation method. Different characterization techniques described the physicochemical nature of betel nut husks activated carbon (BNH-AC) through Fourier transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET), scanning electron microscopy (SEM), and pH point of zero charge. Later, the produced AC was used for methylene blue (MB) adsorption via numerous batch experimental parameters: initial concentrations of MB dye (25-250 mg/L), contact time (0.5-24 hours) and initial pH (2-12). Dye adsorption isotherms were also assessed at three temperatures where the maximum adsorption capacity (381.6 mg/g) was found at 30 °C. The adsorption equilibrium data were best suited to the non-linear form of the Freundlich isotherm model. Additionally, non-linear pseudo-second-order kinetic model was better fitted with the experimental value as well. Steady motion of solute particles from the boundary layer to the BNH-AC's surface was the possible reaction dynamics concerning MB adsorption. Thermodynamic study revealed that the adsorption process was spontaneous and exothermic in nature. Saline water emerged as an efficient eluent for the desorption of adsorbed dye on AC. Therefore, the BNH-AC is a very promising and cost-effective adsorbent for MB dye treatment and has high adsorption capacity.

Synergistic removal of copper and tetracycline from aqueous solution by steam-activated bamboo-derived biochar

Steam-activated biochar (SBC) was prepared and showed excellent performance for synergistic removal of Cu²⁺ and tetracycline (TC). The adsorption capacity of SBC and mutual effect of TC and Cu²⁺ were investigated via single and binary system and the adsorption isotherm. The adsorption capacity of TC was significantly enhanced when it coexisted with Cu²⁺. Likewise, increased amounts of Cu²⁺ were adsorbed in the presence of TC. The presence of NaCl exerted a negative influence on the adsorption of Cu²⁺, while the inhibitory effect of salinity on TC was neutralized by bridge enhancement in the binary system. Bridge enhancement and site competition were involved in the synergistic removal of TC and Cu²⁺. Considering the stable application in simulated and real water samples, SBC showed great potential for synergistic removal of antibiotics and heavy metals.

Plasma-Assisted Surface Modification on the Electrode Interface for Flexible Fiber-Shaped Zn-Polyaniline Batteries

A novel flexible fiber-shaped zinc-polyaniline battery (FZPB) is proposed to enhance the electrochemical performance, mass loading, and stability of polyaniline cathodes. To this end, electron-cyclotron-resonance oxygen plasma-modified carbon fibers are employed. During plasma treatment, on the carbon-fiber surface, O₂⁺ plasma breaks the C-C, C-H, and C-N bonds to form C radicals, while the O₂ molecules are broken down to reactive oxygen species (O⁺, O²⁺, O₂⁺, and O₂²⁺). The C radicals and the reactive oxygen species are combined to homogeneously form oxygen functional groups, such as -OH, -COOH, and -C═O. The surface area and total pore volume of the treated carbon fibers increase as the plasma attacks. During electrodeposition, aniline interacts with the oxygen functional groups to form N-O and N-H bonds and π-π stacking, resulting in a homogeneous and high-loading polyaniline structure and improved adhesion between polyaniline and carbon fibers. In an FZPB, the cathode with plasma-treated carbon fibers and a polyaniline loading of 0.158 mg mg_CF^-1 (i.e., 2.36 mg cm_CF^-1) exhibits a capacity retention of 95.39% after 200 cycles at 100 mA g^-1 and a discharge capacity of 83.96 mA h g^-1 at such a high current density of 2000 mA g^-1, which are ∼1.67 and 1.24 times those of the pristine carbon-fiber-based one, respectively. Furthermore, the FZPB exhibits high flexibility with a capacity retention of 86.4% after bending to a radius of 2.5 mm for 100 cycles as a wearable energy device.

Adsorption of dissolved organic matter from landfill leachate using activated carbon prepared from sewage sludge and cabbage by ZnCl2

Sewage sludge and cabbage (Brassica oleracea) were used to prepare activated carbon by high-temperature inert carbonization with the activator ZnCl₂. The physicochemical characteristics of the sludge-based activated carbon (SAC) were analyzed, and the effects on the removal of chemical oxygen demand (COD) from the landfill leachate by the adsorbent dosage, adsorption time, and the solution pH were investigated in different adsorbents. Three-dimensional fluorescence spectroscopy and gas chromatography-mass spectrometry were used to analyze the organic compounds in the leachate before and after adsorption. The results demonstrated that the average iodine content of the SAC was 535.01 mg/g. The average specific surface area was 917.72 m²/g, and the dominant pore size was in the mesoporous range. The optimum parameters for adsorption were a dosage of 3%, adsorption time of 60 min, and pH = 8, and the COD removal rate reached 85.61%. The adsorption of COD on the SAC was best fitted by the Freundlich model. Additionally, the SAC was found to have a high removal efficiency for refractory organic matter and short-chain alkanes, such as humic acid-like substances, in the leachate but was not effective for long-chain alkanes.

Adsorptive removal of lead (II) ion from water and wastewater media using carbon-based nanomaterials as unique sorbents: A review

Carbon-based nanomaterials and its derivatives such as carbon nanotubes, graphene, reduced graphene oxide, and graphene oxide have been widely used as unique sorbents for removal of both organic and inorganic contaminants due to unique physical and chemical properties. In the review, application of the carbon-based nanomaterials or nanocomposites is considered with particular focus on the lead(II) removal from water and wastewater samples. Moreover, various procedures of synthesis and functionalization of each class of carbon-based nanomaterials were reviewed. A critical review has been given to the adsorption behavior of these nanomaterials and interaction type between the sorbent and lead(II) ion s due to changes in their surface structure and functional group modification for the removal of lead(II)ions. The adsorption capacity, the sorbent selectivity and structure, and the adsorption mechanism for lead(II) ion adsorption with these sorbents were studied and compared. Specific consideration is devoted to effecting of pH of samples as a critical factor in the adsorption of lead(II)ions on each class of carbon-based nanomaterials. Also, the advantages and disadvantages of the nanomaterials or nanocomposites for the adsorption of lead(II) ion were evaluated in detail. In this way, the paper will contribute to presenting suggestions for the preparation of new sorbents to researchers for future study, as well as the remaining research challenges in this field.

Polypyrrole modified magnetic reduced graphene oxide composites: synthesis, characterization and application for selective lead adsorption

To enhance the ability to remove lead from water, polypyrrole modified magnetic Fe₃O₄/reduced graphene oxide composites (PPy-FG) were prepared via in situ polymerization and employed for the Pb(ii) adsorption. The physicochemical structure and adsorption mechanism of the prepared magnetic PPy-FG were studied via vibrating sample magnetometer, X-ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, Brunauer–Emmett–Teller analysis, and X-ray photoelectron spectroscopy. The effects of several factors on Pb(ii) adsorption were evaluated, including pH value, temperature, and competitive ions. Under the optimal conditions (pH 5 and 298 K), the maximum adsorption capacity of PPy-FG was 93.2 mg g⁻¹ giving an improvement of 31% over that of 71 mg g⁻¹ for Fe₃O₄/reduced graphene oxide (Fe₃O₄/rGO). Moreover, the experimental data were well fitted with the Langmuir adsorption model and the pseudo-second-order kinetics model, indicating that the adsorption process was mainly a monolayer chemical adsorption. Thermodynamic studies revealed a spontaneous and endothermic adsorption process. The selective adsorption of Pb(ii) by PPy-FG is superior to that of Fe₃O₄/rGO in the presence of similar metals in the same medium. In addition, the adsorption performance of PPy-FG showed great potential in the remediation of heavy metal contaminated water through using its magnetic properties and excellent affinity for heavy metals.

Compared to Fe₃O₄/rGO, the PPy-FG composites showed desirable adsorption capacity and selectivity for Pb(ii) from water.

A novel hierarchical stiff carbon foam with graphene-like nanosheet surface as the desired adsorbent for malachite green removal from wastewater

A novel hierarchical stiff carbon foam (HSCF) was successfully prepared via a carbothermal reduction between the carbon foam with two-level pore structure and the Al₂O₃ from aluminum sulfate, and used as a bulk adsorbent for removing malachite green (MG) dye. The structures of the HSCF were characterized using SEM, XRD, FTIR, BET, and XPS, and the effects of adsorption condition on the MG removal were studied through batch adsorption experiments. Results show that large-sized and complex-shaped HSCF can be easily fabricated with a high compression strength of 1.58 MPa at a low bulk density (0.10 g cm^-3). The HSCF possesses a fluffy graphene-like nanosheet surface with a mesoporous structure and meanwhile exhibits good hydrophilicity loaded with aluminum hydroxide. The experimental maximum adsorption capacity for MG reaches 425.2 mg g^-1 with a relatively high partition coefficient of 9.38 mg g^-1 μM^-1 at the optimal condition. The experimental data are in good agreement with Langmuir isotherm and pseudo-second-order kinetic model, and meanwhile, the adsorption of MG onto the HSCF is a spontaneous and endothermic process. Also, the HSCF still exhibits good adsorption ability and stability after seven regeneration cycles.

Super Effective Removal of Toxic Metals Water Pollutants Using Multi Functionalized Polyacrylonitrile and Arabic Gum Grafts

Super adsorbent polymers can be considered to be a very efficient solution for wastewater treatment. In general, their adsorption capacities depend on the type and amount of the functional groups present on the surface of the polymers, while their economic value is affected by their cost. Therefore, this study aims to understand the effect of multi-functionalization of cheap Arabic gum on the adsorption capability toward heavy metals. Graft copolymers of polyacrylonitrile (PAN) onto Arabic gum (AG) were prepared in aqueous solution using (KMnO₄/HNO₃) as a redox initiator. Chemical modification of the graft copolymer was carried out by reaction with hydrazine hydrochloride followed by hydrolysis in the basic medium. The modified graft product was characterized by various techniques, such as Fourier transform infrared spectroscopy (FTIR), elemental analysis, scanning electron microscope (SEM), and X-ray powder diffraction (XRD). The modified graft copolymer was used to adsorb Pb²⁺, Cd²⁺ and Cu²⁺ from their aqueous solutions using batch extraction. Different parameters influence the uptake behavior, including contact time, pH, and the initial concentration of the metal ions; all of these were investigated. The kinetics were investigated using the pseudo first order and pseudo second order, and the equilibrium data were analyzed using the Langmuir and Freundlich model. The modified graft product showed the superadsorbent capacity to obtain maximum values (Qmax) 1017, 413 and 396 mg/g for Pb²⁺, Cd²⁺ and Cu²⁺, respectively. Acid treatment with 0.2 M HNO₃ resulted in 96%, 99% and 99% metal recovery for the Pb²⁺, Cd²⁺ and Cu²⁺, respectively. This indicates the recyclability of product for further usage upon drying between treatments.

Carbon Nanomaterials for the Treatment of Heavy Metal-Contaminated Water and Environmental Remediation

Nanotechnology is an advanced field of science having the ability to solve the variety of environmental challenges by controlling the size and shape of the materials at a nanoscale. Carbon nanomaterials are unique because of their nontoxic nature, high surface area, easier biodegradation, and particularly useful environmental remediation. Heavy metal contamination in water is a major problem and poses a great risk to human health. Carbon nanomaterials are getting more and more attention due to their superior physicochemical properties that can be exploited for advanced treatment of heavy metal-contaminated water. Carbon nanomaterials namely carbon nanotubes, fullerenes, graphene, graphene oxide, and activated carbon have great potential for removal of heavy metals from water because of their large surface area, nanoscale size, and availability of different functionalities and they are easier to be chemically modified and recycled. In this article, we have reviewed the recent advancements in the applications of these carbon nanomaterials in the treatment of heavy metal-contaminated water and have also highlighted their application in environmental remediation. Toxicological aspects of carbon-based nanomaterials have also been discussed.

Novel ternary nanohybrids of tetraethylenepentamine and graphene oxide decorated with MnFe2O4 magnetic nanoparticles for the adsorption of Pb(II)

Novel ternary nanohybrids, consisting of tetraethylenepentamine (TEPA), graphene oxide (GO) and manganese ferrite magnetic nanoparticles (TEPA-GO/MnFe₂O₄), were prepared by a facile hydrothermal method and utilized to remove Pb(II) from aqueous solution effectively. The adsorbents were characterized by SEM, TEM, XRD, FTIR, zeta potential analysis, magnetization hysteresis loop, BET and XPS. These nanoparticles exhibited superparamagnetic behavior as well as high removal efficiency for Pb(II). Moreover, numerous amino groups of the functionalized pendant TEPA on GO coupled with the porous structure of TEPA-GO/MnFe₂O₄ contribute to high Pb(II) adsorption capacity. The maximum Pb(II) adsorption capacity of TEPA-GO/MnFe₂O₄ was determined to be 263.2 mg/g at the optimized solution pH of 5.5, much higher than that of GO/MnFe₂O₄ (133.3 mg/g) and GO (196.1 mg/g). The kinetics and isotherm data fitted well with the pseudo-second-order kinetics and the Langmuir isotherm model, respectively. Thermodynamic studies revealed that the Pb(II) adsorption of TEPA-GO/MnFe₂O₄ was a endothermic and spontaneous process. The experimental results corroborated that TEPA-GO/MnFe₂O₄ can be efficaciously reused after washed with HCl, indicative of its potential applications in environmental cleanup.

Patulin removal from apple juice using a novel cysteine-functionalized metal-organic framework adsorbent

Patulin (PAT) is one of the most common toxic contaminants of apple juice, which causes severe food safety issues throughout the apple industry. In order to remove PAT efficiently, a metal-organic framework-based adsorbent (UiO-66(NH₂)@Au-Cys) was successfully synthesized and used for PAT removal from juice-pH simulation solution and real apple juice. Batch adsorption experiments were systematically performed to study the adsorption behavior for PAT. The results showed that adsorption process could be well described by the Pseudo-second order model and Freundlich isotherm model. The maximum adsorption capacity (4.38 µg/mg) was 10 times higher than the microbe-based biosorbents. Thermodynamic investigation demonstrated that adsorption process was spontaneous and endothermic. Furthermore, no marked cytotoxicity on NIH 3T3 cell lines was observed when the concentration of the adsorbent was lower than 10 μg/mL. Therefore, UiO-66(NH₂)@Au-Cys is a potential adsorbent for PAT removal from apple juice with little quality changes.

A superfast hexavalent chromium scavenger: Magnetic nanocarbon bridged nanomagnetite network with excellent recyclability

In this work, a nanocarbon bridged nanomagnetite network (NC-NMN) is developed through the electrospinning of epichlorohydrin functionalized polystyrene (f-PS), followed by the direct calcination of f-PS and ferric nitrate, which is capable of superfast removing hexavalent chromium (Cr(VI)) from polluted water within only 15 s benefiting from its gridding framework, with an adsorption rate constant of 1.64 g mg^-1 min^-1 according to the pseudo-second-order kinetics. The well-fitted Langmuir isotherm model indicates a monolayer adsorption for Cr(VI) on NC-NMN. The thermodynamic parameters including negative ΔG° and positive ΔH° demonstrate that the Cr(VI) adsorption on NC-NMN is spontaneous and endothermic. The Cr(VI) adsorption retention, which is only 3.8%, is achieved for NC-NMN after five cycles, exhibiting a prominent stability and an excellent recyclability. X-ray photoelectron spectroscopy (XPS), zeta potential and energy-filter transmission electron spectroscopy (EFTEM) results illustrate that both the electrostatic attraction and the network structure of NC-NMN are responsible for the superior Cr(VI) adsorption performance. This work intends to provide a new method for designing the novel structure materials for polluted water treatment.

MnFe2O4-graphene oxide magnetic nanoparticles as a high-performance adsorbent for rare earth elements: Synthesis, isotherms, kinetics, thermodynamics and desorption

In recent decades, considerable amounts of rare earth elements have been used and then released into industrial wastewater, which caused serious environmental problems. In this work, in order to recycle rare earth cations (La³⁺ and Ce³⁺) from aqueous solutions, MnFe₂O₄-Graphene oxide magnetic nanoparticles were synthesized and after characterization studies, their adsorption isotherms, kinetics, thermodynamics and desorption were comprehensively investigated. Characterized was performed using XRD, FE-SEM, FT-IR, Raman spectroscopy, VSM, BET and DLS. REE adsorption on MnFe₂O₄-GO was studied for the first time in the present work and the maximum adsorption capacity at the optimum condition (room temperature and pH = 7) for La³⁺ and Ce³⁺ were 1001 and 982 mg/g respectively, and the reactions were completed within 20 min. In addition, the adsorption data were well matched with the Langmuir model and the adsorption kinetics were fitted with the pseudo-second order model. The thermodynamic parameters were calculated and the reactions were found to be endothermic and spontaneous. Moreover, the Dubinin-Radushkevich model predicted chemical ion-exchange adsorption. Desorption studies also demonstrated that MnFe₂O₄-GO can be regenerated for multiple reuses. Overall, high adsorption capacity, chemical stability, reusability, fast kinetics, easy magnetic separation, and simple synthesis method indicated that MnFe₂O₄-GO is a high-performance adsorbent for REE.

Development of an auto-phase separable and reusable graphene oxide-potato starch based cross-linked bio-composite adsorbent for removal of methylene blue dye

In this work, we report the development of a cross-linked bio-composite consisting of graphene oxide, potato starch, cross-linker glutaraldehyde and its application to adsorption of the industrial dye, methylene blue, from aqueous solution. The inexpensiveness, non-hazardous nature and easy bio-degradability are the major reasons for the selection of starch material as one of the components of the bio-composite. The bio-composite has been characterized by FTIR, SEM, XRD, particle size and zeta potential analysis. The FTIR analysis reveals the nature of the binding sites and surface morphology of the bio-composite can be understood through SEM. The auto-phase separability of the adsorbent i.e., the precipitation of the adsorbent without any mechanical means is another factor which makes this particular material very attractive as an adsorbent. Parameters like adsorbent dosage, pH, temperature, rotation speed and salt concentration have been varied to find out the suitable dye adsorption conditions. Furthermore, the time dependence of adsorption process has been analyzed using pseudo-first and pseudo-second order kinetics. The adsorption isotherms have been constructed to suggest convincing mechanistic pathway for this adsorption process. Finally, desorption studies have been successfully performed in 3 cycles, establishing the reusability of the material, which should allow the adsorbent to be economically promising for practical application in wastewater treatment.

High Electrochemical Sensitivity of TiO2- x Nanosheets and an Electron-Induced Mutual Interference Effect toward Heavy Metal Ions Demonstrated Using X-ray Absorption Fine Structure Spectra

Mutual interference is a severe issue that occurs during the electrochemical detection of heavy metal ions. This limitation presents a notable drawback for its high sensitivity to specific targets. Here, we present a high electrochemical sensitivity of ∼237.1 μA cm^-2 μM^-1 toward copper(II) [Cu(II)] based on oxygen-deficient titanium dioxide (TiO_{2- x}) nanosheets. We fully demonstrated an atomic-level relationship between electrochemical behaviors and the key factors, including the high-energy (001) facet percentage, oxygen vacancy concentration, surface -OH content, and charge carrier density, is fully demonstrated. These four factors were quantified using Raman, electron spin resonance, X-ray photoelectron spectroscopy spectra, and Mott-Schottky plots. In the mutual interference investigation, we selected cadmium(II) [Cd(II)] as the target ion because of the significant difference in its stripping potential (∼700 mV). The results show that the Cd(II) can enhance the sensitivity of TiO_{2- x} nanosheets toward Cu(II), exhibiting an electron-induced mutual interference effect, as demonstrated by X-ray absorption fine structure spectra.