NOx Storage−Reduction Catalysis: From Mechanism and Materials Properties to Storage−Reduction Performance

Utilization of Reactive Nitrogen Compounds for Nitrogen Circular Economy

Nitrogen oxides (NOx) should be purified according to environmental regulations, being restricted increasingly year by year. A wide variety of denitration technologies, such as selective catalytic reduction (SCR) of NOx to nitrogen (N2) and NOx storage reduction (NSR) to N2 by injecting reducing agents like ammonia (NH3), has so far been developed practically. Sophisticated catalytic approaches are perhaps mandatory for the sustainability in energy including complete purification of NOx. As one of the solutions to overcome problems for environment and resource simultaneously, this concept article focuses on the utilization of reactive nitrogen (Nr) compounds, mainly NOx, for encouraging an opening to consider nitrogen circular economy. For the recycling of NOx via NH3, a challenging but rational catalytic technology can be proposed by an alternate switching the inlet gas between NOx containing oxidative gas and H2 containing reductive one without an operation to change the reaction temperature. Considering the reactivity of NOx higher than that of N2, this kind of NOx to NH3 (NTA) process is promising for synthesizing NH3, being valuable not only as fertilizer but also as fuel in near future.

Kinetics and H2O Influence on NOx Trapping and Selective Catalytic Reduction over Ce/Pd Doping Catalyst

In this paper, the removal effects and activation energy of Ce and Pd doping on pollutants (CO, C3H6, and NO) were comparatively analyzed by using characterization methods and constructed kinetic equations. Furthermore, the problems of the water influence mechanism on the NSR process were also discussed. The results show the following: (1) Pd doping effectively improves the removal of CO (80%) and C3H6 (71%) in the low-temperature section of the catalyst (150-250 °C) compared to Ce doping, while Ce doping exhibits excellent low-temperature conversion of NO. (2) The reaction activation energy of the LaKMnPdO3 catalyst was 9784 kJ/mol, which was significantly lower than that of the LaKMnCeO3 catalyst. (3) The presence of H2O has an important enhancement effect in the storage performance of the LaKMnPdO3 catalyst for NOx but decreases the catalytic reduction of NO. It provides a solution for the effective treatment of the increasing problems of particulate matter and ozone pollution.

Dielectric Properties of Materials Used for Microwave-Based NOx Gas Dosimeters

Nitrogen oxides (NOx), primarily generated from combustion processes, pose significant health and environmental risks. To improve the coordination of measures against excessive NOx emissions, it is necessary to effectively monitor ambient NOx concentrations, which requires the development of precise and cost-efficient detection methods. This study focuses on developing a microwave- or radio frequency (RF)-based gas dosimeter for NOx detection and addresses the optimization of the dosimeter design by examining the dielectric properties of LTCC-based (Low-Temperature Co-fired Ceramics) sensor substrates and barium-based NOx storage materials. The measurements taken utilizing the Microwave Cavity Perturbation (MCP) method revealed that these materials exhibit more pronounced changes in dielectric losses when storing NOx at elevated temperatures. Consequently, operating such a dosimeter at high temperatures (above 300 °C) is recommended to maximize the sensor signal. To evaluate their high-temperature applicability, LTCC substrates were analyzed by measuring their dielectric losses at temperatures up to 600 °C. In terms of NOx storage materials, coating barium on high-surface-area alumina resolved issues related to limited NOx adsorption in pure barium carbonate powders. Additionally, the adsorption of both NO and NO2 was enabled by the application of a platinum catalyst. The change in dielectric losses, which provides the main signal for an RF-based gas dosimeter, only depends on the stored amount of NOx and not on the specific type of nitrogen oxide. Although the change in dielectric losses increases with the temperature, the maximum storage capacity of the material decreases significantly. In addition, at temperatures above 350 °C, NOx is mostly weakly bound, so it will desorb in the absence of NOx. Therefore, in the future development of a reliable RF-based NOx dosimeter, the trade-off between the sensor signal strength and adsorption behavior must be addressed.

Electric field-assisted NSR process for lean NOx reduction at low temperatures

Lean-burn engines are gaining attention for their lower CO2 emissions, higher thermal efficiency, and improved fuel economy compared to traditional combustion engines. However, they present some difficulty for reducing nitrogen oxides (NOx) because of residual oxygen. To address this difficulty, NOx storage reduction (NSR) system, which combines noble metals and NOx adsorbents, is developed as a viable approach. But it requires cyclic operation, which adversely affects fuel efficiency. A novel approach proposed in this work is electric field-assisted lean NOx reduction, which applies an electric field to the NSR catalyst during lean conditions. This innovation uses surplus vehicle electricity for exhaust purification, enhances hydrogen transfer, and improves NOx reduction, even at low temperatures. Tests with a 3 wt% Pt-16 wt% BaO/CeO2 catalyst demonstrate markedly higher NOx conversion to N2 (13.1% vs. 2.9% without an electric field). This process is effective with extended electric field exposure, doubling the conversion rate. Electric field-assisted lean NOx reduction, by improving NSR technology, can enhance NOx conversion efficiency, reduce emissions, and optimize fuel efficiency in lean-burn engines.

Advances in photocatalytic NO oxidation by Z-scheme heterojunctions

The fast development of urbanisation and industrialisation has led to a rise in nitrogen oxide (NOx) emissions, specifically nitric oxide (NO). One effective method for reducing the harmful effects of this dangerous air pollutant on both human health and the environment is the photocatalytic oxidation of NO. Z-scheme heterojunctions enhance incident light utilisation and increase photocatalytic activity, eventually leading to better NO oxidation performance by encouraging the effective separation of charges and migration. A comprehensive discussion of Z-scheme-based heterojunctions is provided in this review paper, with a focus on their applications in the photocatalytic oxidation of NO. Significant progress has been made in the fabrication of efficient photocatalytic devices in recent years, with Z-scheme-based heterojunctions proving to be particularly successful. The review looks into the various methodologies used to create Z-scheme-based heterojunctions as well as photocatalytic NO oxidation mechanisms. Recent studies on photocatalysts employing Z-scheme heterojunctions for the photocatalytic oxidation of NO are also discussed. The possibilities for new opportunities as well as the present challenges, barriers, advances, and solutions have been emphasized.

Technological solutions for NOx, SOx, and VOC abatement: recent breakthroughs and future directions

NOx, SOx, and carbonaceous volatile organic compounds (VOCs) are extremely harmful to the environment, and their concentrations must be within the limits prescribed by the region-specific pollution control boards. Thus, NOx, SOx, and VOC abatement is essential to safeguard the environment. Considering the importance of NOx, SOx, and VOC abatement, the discussion on selective catalytic reduction, oxidation, redox methods, and adsorption using noble metal and non-noble metal-based catalytic approaches were elaborated. This article covers different thermal treatment techniques, category of materials as catalysts, and its structure-property insights along with the advanced oxidation processes and adsorption. The defect engineered catalysts with lattice oxygen vacancies, bi- and tri-metallic noble metal catalysts and non-noble metal catalysts, modified metal organic frameworks, mixed-metal oxide supports, and their mechanisms have been thoroughly reviewed. The main hurdles and potential achievements in developing novel simultaneous NOx, SOx, and VOC removal technologies are critically discussed to envisage the future directions. This review highlights the removal of NOx, SOx, and VOC through material selection, properties, and mechanisms to further improve the existing abatement methods in an efficient way.

Resistive Multi-Gas Sensor for Simultaneously Measuring the Oxygen Stoichiometry (λ) and the NOx Concentration in Exhausts: Engine Tests under Dynamic Conditions

Due to increasingly stringent limits for NO_x emissions, there is now more interest than ever in cost-effective, precise, and durable exhaust gas sensor technology for combustion processes. This study presents a novel multi-gas sensor with resistive sensing principles for the determination of oxygen stoichiometry and NO_x concentration in the exhaust gas of a diesel engine (OM 651). A screen-printed porous KMnO₄/La-Al₂O₃ film is used as the NO_x sensitive film, while a dense ceramic BFAT (BaFe_0.74Ta_0.25Al_0.01O_3-δ) film prepared by the PAD method is used for λ-measurement in real exhaust gas. The latter is also used to correct the O₂ cross-sensitivity of the NO_x sensitive film. This study presents results under dynamic conditions during an NEDC (new European driving cycle) based on a prior characterization of the sensor films in an isolated sensor chamber with static engine operation. The low-cost sensor is analyzed in a wide operation field and its potential for real exhaust gas applications is evaluated. The results are promising and, all in all, comparable with established, but usually more expensive, exhaust gas sensors.

CuCeOx/CuO Catalyst Derived from the Layered Double Hydroxide Precursor: Catalytic Performance in NO Reduction with CO in the Presence of Water and Oxygen

Valencies of metal species and lattice defects, such as oxygen vacancies, play a pivotal role in metal oxide-catalyzed reactions. Herein, we report a promising synthetic strategy for preparing CuO-supported CuCeO_x catalysts (CuCeO_x/CuO) by calcination of a hydrotalcite precursor [Cu₆Ce₂(OH)₁₆]CO₃·nH₂O. The structural and chemical properties of catalysts were characterized by XRD, ICP-AES, TEM, TPR, NH₃-TPD, XPS, Raman spectroscopy, and N₂ adsorption, which revealed that the thermal pretreatment in an oxidative atmosphere caused segregation and reconstitution processes of the precursor, resulting in a mesoporous catalyst consisting of well-dispersed CuO-supported CuCeO_x clusters of 1.8-3.2 nm in size with a high population of oxygen vacancies. The as-prepared catalyst shows excellent catalytic performance in the reduction of NO by CO in the absence as well as in the presence of water and oxygen. This behavior is attributed to its high oxygen defect concentration facilitating the interplay of the redox equilibria between Cu²⁺ and reduced copper species (Cu⁺/Cu⁰) and (Ce⁴⁺/Ce³⁺). The high surface population of oxygen vacancies and in situ-generated metallic copper species have been evidenced by Raman spectroscopy and X-ray photoelectron spectroscopy. The layered double hydroxide-derived CuCeO_x/CuO also showed good water tolerance and long-term stability. In situ infrared spectroscopy investigations indicated that adsorbed hyponitrite species are the main reaction intermediates of the NO conversion as also corroborated by theoretical simulations.

CuO decorated vacancy-rich CeO2 nanopencils for highly efficient catalytic NO reduction by CO at low temperature

With the rapid development of transportation and vehicles, the elimination of NO_x and CO has highly attracted public attention. In this work, vacancy-rich CeO₂ nanopencil supported CuO catalysts (CuO/CeO₂-NPC) were successfully prepared for NO reduction by CO. Importantly, CeO₂ with nanopencil-like shape (CeO₂-NPC) have been synthesis by solvothermal method for the first time. The physicochemical properties of all samples were studied in detail by combining the means of X-ray diffraction (XRD), Raman spectroscopy, electron paramagnetic resonance (EPR), X-ray photoelectron spectroscopy (XPS), H₂-temperature-programmed reduction (H₂-TPR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), N₂ physisorption (Brunauer-Emmett-Teller), and NO and CO temperature-programmed desorption (NO-TPD and CO-TPD) techniques. Compared with CeO₂ nanorods and nanoparticles supported CuO catalysts (CuO/CeO₂-NR and CuO/CeO₂-NP), the CuO/CeO₂-NPC catalysts showed the highest catalytic activity, affording more than 90% NO conversion at 69 °C as well as excellent H₂O tolerance at 150 °C, which is superior to catalysts previously reported. Characterization results indicated that the synergistic effect between the well-dispersed CuO and the CeO₂ nanopencil support enables a favorable electron transfer between these components and enhances the density of surface oxygen vacancies and Cu⁺ species, which consequently accelerating the redox cycle. The results indicated that the morphology control of CeO₂ support could be an efficient way to evidently enhance the catalytic performance for NO + CO reaction.

Exceptionally high and reversible NOx uptake by hollow Mn-Fe composite nanocubes derived from Prussian blue analogues

Noble metal-based catalysts are widely used as passive NO_x adsorbers (PNA) for cold-start NO_x emissions; however, efficient porous materials as an alternative have great development potential. Herein, porous Mn-Fe composites with hollow nanocubes derived from Prussian blue analogue (PBA) precursors were used as PNA. The effects of O₂, the molar ratio of Mn/Fe, calcination temperature and reaction temperature on their adsorption capacity were explored. The physicochemical properties of the obtained catalysts were systematically characterized by XRD, SEM, BET surface area, TGA, XPS and DRIFT techniques. The developed Mn₁Fe₂-450 presented excellent NO_x uptake (more than 2.16 mmol g^-1 at 200 °C). Moreover, a high NO_x adsorption performance was also retained in the presence of 10% water vapor. The existing Mn³⁺ and Fe²⁺ species could contribute to the NO_x adsorption and gaseous O₂ can accelerate NO activation to form more easily adsorbed NO₂. Surface NO₂ is further diffused and stored into the bulk of the Mn-Fe composite in the form of nitrite and nitrate. This work revealed a novel candidate for PNA catalysts, which might provide inspiration for the design of new adsorbent materials.

Nitrogen atom coordination tuned transition metal catalysts for NO oxidation and reduction

Developing an efficient catalyst for NO oxidation and reduction at ambient temperature is a significant challenge. Recent studies have suggested that the N-coordinated transition metal (TM) single atom catalysts (SACs) have high catalytic activity and stability. Herein, we report the activation potential of a series of 3d TM atoms supported on N coordination-tuned graphene (GR) for NO oxidation and reduction. The results show that the N coordination pattern can greatly alter the catalytic reactivity of TM on the catalysts, and the TM atom on the catalysts with three-coordinated pyridinic nitrogen TM-N₃@GR exhibit the strongest chemical activity. Among the TM-N₃@GR catalysts, Ti-N₃@GR is the most promising candidate. The rate constants and equilibrium constants were calculated to evaluate the kinetic and thermodynamic feasibility of the catalytic reaction, respectively. Our results demonstrate that the reduction of NO to N₂ on Ti-N₃@GR can occur at ambient temperature with a large exotherm of 6.99 eV, and the oxidation of NO to NO₂ on Ti-N₃@GR can easily proceed when the temperature reaches 360 K with a large equilibrium constant. Our studies are of great significance for understanding the performance of N coordination-tuned catalysts and designing Ti-based catalysts for NO oxidation and reduction.

On the Suitability of NOx-Storage-Catalysts for Hydrogen Internal Combustion Engines and a Radio Frequency-Based NOx Loading Monitoring

Hydrogen combustion engines can contribute to CO2-free mobility. However, they produce NOx emissions, albeit only to an extremely small extent when operated very leanly. One approach to reduce these emissions even further is to use exhaust gas aftertreatment systems like NOx storage catalysts (NSC). So far, they have mainly been used in diesel or gasoline applications. This contribution shows that under conditions such as those prevailing in hydrogen engines, the NSC can achieve not only a higher storage capacity for nitrogen oxides (NOx) but also a higher conversion. To ensure permanently high conversion rates, the amount of stored NOx has to be monitored permanently to prevent NOx breakthroughs. Conventional NOx sensors may not be accurate enough due to the very low NOx emissions. The functionality of the radio frequency (RF) sensor, which enables a direct determination of the NOx loading, is demonstrated for operation under hydrogen conditions. Furthermore, the influence of rich exhaust gas on the RF signal, which is relevant for a correct NOx loading determination during regeneration, is analyzed.

Enhanced Stability and Catalytic Performance of Active Rh Sites on Al2O3 Via Atomic Layer Deposited ZrO2

Modulating the Rh active sites on surfaces of Al₂O₃ is crucial to developing effective three-way catalysts. Herein, an ultralow amount of ZrO₂ (0.0179%) was deposited onto Al₂O₃ nanorods via atomic layer deposition (ALD) to form a catalyst with both thermal stability and low-temperature activity. The results demonstrate that the ALD-ZrO₂ is conducive to improve the catalytic activity of the Rh site and inhibit the formation of irreducible Rh species at high temperature. The obtained catalysts show satisfactory performance for a model NO-CO reaction even after thermal aging at 1050 °C. This strategy shows that a molecularly precise synthesis can lead to the robust promotion of Rh activity under low temperature and provide a promising path toward reducing the deactivation of catalysts at high temperature.

Al-Decorated C2N Monolayer as a Potential Catalyst for NO Reduction with CO Molecules: A DFT Investigation

Developing efficient and economical catalysts for NO reduction is of great interest. Herein, the catalytic reduction of NO molecules on an Al-decorated C2N monolayer (Al-C2N) is systematically investigated using density functional theory (DFT) calculations. Our results reveal that the Al-C2N catalyst is highly selective for NO, more so than CO, according to the values of the adsorption energy and charge transfer. The NO reduction reaction more preferably undergoes the (NO)2 dimer reduction process instead of the NO direct decomposition process. For the (NO)2 dimer reduction process, two NO molecules initially co-adsorb to form (NO)2 dimers, followed by decomposition into N2O and Oads species. On this basis, five kinds of (NO)2 dimer structures that initiate four reaction paths are explored on the Al-C2N surface. Particularly, the cis-(NO)2 dimer structures (Dcis-N and Dcis-O) are crucial intermediates for NO reduction, where the max energy barrier along the energetically most favorable pathway (path II) is as low as 3.6 kcal/mol. The remaining Oads species on Al-C2N are then easily reduced with CO molecules, being beneficial for a new catalytic cycle. These results, combined with its low-cost nature, render Al-C2N a promising catalyst for NO reduction under mild conditions.

Contributions of Washcoat Components in Different Configurations to the NOX and Oxygen Storage Performance of LNT Catalysts

In addition to SCR systems, lean NOX traps (LNTs) are also used for exhaust aftertreatment of lean burn internal combustion engines to sustainably reduce NOX emissions. Modern LNTs consist of different functional compounds to maximize the performance during NOX storage and regeneration. Based on the material analysis of a serial production LNT, PGM loaded BaO, Al2O3, MgAl2O4, and CeO2 were identified as the main base materials. In this paper, the NOX storage capacity (NSC) of these compounds is investigated both as single catalysts and as physical mixtures to identify possible synergistic effects. Therefore, commercially available support materials were loaded with Platinum and tested in granular form under realistic conditions. To optimize the performance by reducing the diffusion pathways for NOX molecules during storage, PGM, BaO, and Ceria were combined in a composite by the incipient wetness impregnation of alumina. As a result, the temperature dependent NSC of the commercial LNT could be reached with the Pt/Rh/Ba10Ce25/Al2O3 infiltration composite, while reducing the oxygen storage capacity by about 45%. Without the additional Rhodium coating, the low-temperature NSC was insufficient, highlighting the important contribution of this precious metal to the overall performance of LNTs.

Advances in Designing Efficient La-Based Perovskites for the NOx Storage and Reduction Process

To overcome the inherent challenge of NOx reduction in the net oxidizing environment of diesel engine exhaust, the NOx storage and reduction (NSR) concept was proposed in 1995, soon developed and commercialized as a promising DeNOx technique over the past two decades. Years of practice suggest that it is a tailor-made technique for light-duty diesel vehicles, with the advantage of being space saving, cost effective, and efficient in NOx abatement; however, the over-reliance of NSR catalysts on high loadings of Pt has always been the bottleneck for its wide application. There remains fervent interest in searching for efficient, economical, and durable alternatives. To date, La-based perovskites are the most explored promising candidate, showing prominent structural and thermal stability and redox property. The perovskite-type oxide structure enables the coupling of redox and storage centers with homogeneous distribution, which maximizes the contact area for NOx spillover and contributes to efficient NOx storage and reduction. Moreover, the wide range of possible cationic substitutions in perovskite generates great flexibility, yielding various formulations with interesting features desirable for the NSR process. Herein, this review provides an overview of the features and performances of La-based perovskite in NO oxidation, NOx storage, and NOx reduction, and in this way comprehensively evaluates its potential to substitute Pt and further improve the DeNOx efficiency of the current NSR catalyst. The fundamental structure–property relationships are summarized and highlighted to instruct rational catalyst design. The critical research needs and essential aspects in catalyst design, including poisoner resistance and catalyst sustainability, are finally addressed to inspire the future development of perovskite material for practical application.

Adsorption and Sensing Performances of Pristine and Au-Decorated Gallium Nitride Monolayer to Noxious Gas Molecules: A DFT Investigation

In this study, the adsorption of noxious gas molecules (NO, Cl₂, and O₃) on GaN and Au-decorated GaN was systematically scrutinized, and the adsorption energy, bond length, charge, density of state (DOS), partial density of state (PDOS), electron deformation density (EDD), and orbitals were analyzed by the density functional theory (DFT) method. It is found that the interaction between NO and pristine GaN is physical adsorption, while GaN chemically reacts with Cl₂ and O₃. These observations suggest that pristine GaN may be a candidate for the detection of Cl₂ and O₃. The highly activated Au-decorated GaN can enhance the adsorption performance toward NO and convert the physical adsorption for NO into chemical adsorption, explaining the fact that precious metal doping is essential for regulating the electronic properties of the substrate material. This further confirms the well-established role of Au-decorated GaN in NO gas-sensing applications. In addition, the adsorption performance of Au-decorated GaN for Cl₂ and O₃ molecules is highly improved, which provides guidance to scavenge toxic gases such as Cl₂ and O₃ by the Au-decorated GaN material.

Electrochemical reduction of NO catalyzed by boron-doped C60 fullerene: a first-principles study

The electrochemical reduction of nitrogen monoxide (NO) is one of the most promising approaches for converting this harmful gas into useful chemicals. Using density functional theory calculations, the work examines the potential of a single B atom doped C60 fullerene (C59B) for catalytic reduction of NO molecules. The results demonstrate that the NO may be strongly activated over the B atom of C59B, and that the subsequent reduction process can result in the formation of NH3 and N2O molecules at low and high coverages, respectively. Based on the Gibbs free energy diagram, it is inferred that the C59B has excellent catalytic activity for NO reduction at ambient conditions with no potential-limiting. At normal temperature, the efficient interaction between the *NOH and NO species might lead to the spontaneous formation of the N2O molecule. Thus, the findings of this study provide new insights into NO electrochemical reduction on heteroatom doped fullerenes, as well as a unique strategy for fabricating low-cost NO reduction electrocatalysts with high efficiency.

Experimental and numerical investigation of NO oxidation on Pt/Al2O3- and NOx storage on Pt/BaO/Al2O3-catalysts

Effects of temperature and inlet conditions on NO oxidation and NOx storage, as well as reduced NOx storage capacity over time – reflected by changes of measured NO concentration, which are reproduced by CFD using detailed reaction mechanisms.

Effect of the Configuration of Copper Oxide-Ceria Catalysts in NO Reduction with CO: Superior Performance of a Copper-Ceria Solid Solution

Various copper-ceria-based composites have attracted attention as efficient catalysts for the reduction of NO with CO. In this comparative study, we have examined the catalytic potential of different configurations of copper oxide-ceria catalysts, including catalysts based on a copper-ceria solid solution, copper oxide particles supported on ceria, and ball-milled copper oxide-ceria. The structurally different interfaces between the constituents of these catalysts afforded very different catalytic performances. The solid solution catalyst outperformed the corresponding ceria-supported and ball-milled CuO-CeO₂ catalysts. The copper cations incorporated into the ceria lattice strongly improved the activity, N₂ selectivity, and water vapor tolerance compared to the other catalyst configurations. The experimental observations are supported by first-principles density functional theory (DFT) studies of the reaction pathway, which indicate that the incorporation of Cu cations into the ceria matrix lowers the energy required for activating the lattice oxygen, thereby enhancing the formation and healing of oxygen vacancies, and thus promoting NO reduction with CO.

Ordered Nanostructure Catalysts Efficient for NOx Storage/Reduction (NSR) Processes

NOx emissions in the atmosphere can cause various environmental problems, which should be strictly controlled and regulated. Furthermore, because of the limited amount of crude oil resources in the world and severe global warming, the development of fuel-efficient vehicles has long been desired. Accordingly, efficient NOx storage and reduction catalysts have been developed over the decades, called NSR (NOx storage/reduction) catalysts. In the present article, recent advances in NSR catalysts which possess ordered nanostructures will be summarized, including our noble Pt/KNO3/K-titanate nanobelt (KTN), Pt-KNO3/CeO2 and Pt-KNO3/ZrO2 catalysts, as well as nanoporous Ni-phosphate (VSB-5) and Co-substituted VSB-5 catalysts.

NOx Storage on BaTi0.8Cu0.2O3 Perovskite Catalysts: Addressing a Feasible Mechanism

The NOx storage mechanism on BaTi_0.8Cu_0.2O₃ catalyst were studied using different techniques. The results obtained by XRD, ATR, TGA and XPS under NOx storage-regeneration conditions revealed that BaO generated on the catalyst by decomposition of Ba₂TiO₄ plays a key role in the NOx storage process. In situ DRIFTS experiments under NO/O₂ and NO/N₂ show that nitrites and nitrates are formed on the perovskite during the NOx storage process. Thus, it seems that, as for model NSR catalysts, the NOx storage on BaTi_0.8Cu_0.2O₃ catalyst takes place by both "nitrite" and "nitrate" routes, with the main pathway being highly dependent on the temperature and the time on stream: (i) at T < 350 °C, NO adsorption leads to nitrites formation on the catalyst and (ii) at T > 350 °C, the catalyst activity for NO oxidation promotes NO₂ generation and the nitrate formation.

Effect of Absorbents on NOx Removal through Polyvinylidene Fluoride (PVDF) Hollow Fiber Membrane Modules

NOx (NO and NO2) are air toxins that endanger life and represent a hazard to the environment, such as photochemical smog, global warming, acid rain, ozone depletion, and the occurrence of respiratory infections. Some technological strategies to diminish NOx emissions to meet regulations depend on two techniques: the dry process and the wet process. This study applies polyvinylidene fluoride (PVDF) hollow fiber membrane modules as a medium to remove NOx from solutions containing several absorbents such as hydrogen peroxide and nitric acid (H2O2-HNO3) solutions, sodium chlorite and sodium hydroxide (NaClO2-NaOH) solutions, and sodium chlorate and sodium hydroxide (NaClO3-NaOH) solutions. The experimental results showed that the oxidant’s strength influences NOx removal efficiency, where the absorbent solutions containing hydrogen peroxide had the highest removal efficiency as hydrogen peroxide is the most potent oxidant, followed by sodium chlorite and sodium chlorate. The three pairs of absorbents also gave a high NOx removal efficiency (above 90%), which means that all the absorbents used in the study are very potential to be used to diminish NOx via the wet process. NOx removal efficiency at the same feed gas flow rate increased as the number of fiber and absorbent concentrations is increased. However, NOx removal efficiency is reduced as the feed gas flow rate is increased at the same membrane module and absorbent concentration.

NOx Storage Performance at Low Temperature over Platinum Group Metal-Free SrTiO3-Based Material

Pt-based catalysts are commonly employed as NOx-trapping catalysts for automobiles, while perovskite oxides have received attention as Pt-free NOx-trapping catalysts. However, the NOx storage performance of perovskite catalysts is significantly inferior at low temperatures and with coexisting gases such as H2O, CO2, and SO2. This study demonstrates that NOx storage reactions proceed over redox site (Mn, Fe, and Co)-doped SrTiO3 perovskites. Among the examined catalysts, Mn-doped SrTiO3 exhibited the highest NOx storage capacity (NSC) and showed a high NSC even at a low temperature of 323 K. Moreover, the high NOx storage performance of Mn-doped SrTiO3 was retained in the presence of poisoning gases (H2O, CO2, and SO2). NO oxidation experiments revealed that the NSC of Co-doped SrTiO3 was dependent on the NO oxidation activity from NO to NO2 via lattice oxygen, which resulted in an inferior NSC at low temperatures. On the other hand, Mn-doped SrTiO3 successfully adsorbed NO molecules onto its surface at 323 K without the NO oxidation process using lattice oxygens. This unique adsorption behavior of Mn-doped SrTiO3 was concluded to be responsible for the high NSC in the presence of poisoning gases.

A Robust Mesoporous Al2 O3 -Based Nanocomposite Catalyst for Abundant NOx Storage with Rational Design of Pt and Ba Species

The nanostructural design of heterogeneous catalysts has often been demanded for assessing synergetic effects, which should be developed further by using high-surface-area porous metal oxide supports. However, such opportunities have been undermined by the poor stability of ordered mesoporous structures. Herein, rational design is demonstrated to obtain nanocomposite catalysts showing improved NO_x storage properties owing to the presence of Ba species over a well-designed mesoporous alumina (Al₂ O₃ ) support. It is found that Ba species are impregnated successfully only after the stabilization of the mesoporous structure by full crystallization of Al₂ O₃ frameworks to the γ-phase, with the formation of Pt nanoparticles coinciding with complete removal of organic components. All the insights during this synthetic procedure are essential for designing high-performance catalysts to purify and recover NO_x molecules, and are applied for designing a variety of cutting-edge mesoporous nanocomposite catalysts.

Improving the Performance of Gd Addition on Catalytic Activity and SO2 Resistance over MnOx/ZSM-5 Catalysts for Low-Temperature NH3-SCR

SO2 poisoning is a great challenge for the practical application of Mn-based catalysts in low-temperature selective catalytic reduction (SCR) reactions of NOx with NH3. A series of Gadolinium (Gd)-modified MnOx/ZSM-5 catalysts were synthesized via a citric acid–ethanol dispersion method and evaluated by low-temperature NH3-SCR. Among them, the GdMn/Z-0.3 catalyst with the molar ratio of Gd/Mn of 0.3 presented the highest catalytic activity, in which a 100% NO conversion could be obtained in the temperature range of 120–240 °C. Furthermore, GdMn/Z-0.3 exhibited good SO2 resistance compared with Mn/Z in the presence of 100 ppm SO2. The results of Brunauer–Emmett–Teller (BET), X-ray photoelectron spectroscopy (XPS), temperature-programmed reduction of H2 (H2-TPR) and temperature-programmed desorption of NH3 (NH3-TPD) illustrated that such catalytic performance was mainly caused by large surface area, abundant Mn4+ and surface chemisorbed oxygen species, strong reducibility and the suitable acidity of the catalyst. The in situ diffuse reflectance infrared Fourier transform spectra (DRIFTS) results revealed that the addition of Gd greatly inhibited the reaction between the SO2 and MnOx active sites to form bulk manganese sulfate, thus contributing to high SO2 resistance. Moreover, in situ DRIFTS experiments also shed light on the mechanism of low-temperature SCR reactions over Mn/Z and GdMn/Z-0.3, which both followed the Langmuir–Hinshelwood (L–H) and Eley–Rideal (E–R) mechanism.

Oxidation and Storage Mechanisms for Nitrogen Oxides on Variously Terminated (001) Surfaces of SrFeO3-δ and Sr3Fe2O7-δ Perovskites

The Ruddlesden-Popper (RP)-type layered perovskite is a candidate material for a new nitrogen oxide (NO_x) storage catalyst. Here, we investigate the adsorption and oxidation of NO_x on the (001) surfaces of RP-type oxide Sr₃Fe₂O_7-δ for all of the terminations by comparing to those of simple perovskite SrFeO_3-δ by the density functional theory (DFT) calculations. The possible (001) cleavages of Sr₃Fe₂O₇ generate two FeO₂- and three SrO-terminated surfaces, and the calculated surface energies indicated that the SrO-terminated surface generated by the cleavage at the rock salt layer is the most stable one. The oxygen of the FeO₂-terminated surfaces could be removed with significantly low energy because the process involves the favorable reduction of the Fe⁴⁺ site. Consequently, the surface oxygen at the FeO₂ site could easily oxidize adsorbed NO to NO₂ by the Mars-van Krevelen mechanism. The resulting oxygen vacancy in the surface would be filled easily with lattice oxygen in bulk. The oxidation of NO with adsorbed molecular O₂ was unfavorable by both the Langmuir-Hinshelwood and Eley-Rideal mechanisms because this process does not involve the reduction of the Fe⁴⁺ site. The oxygen of the SrO-terminated surfaces was tightly bound and acted as the adsorption site of NO and NO₂. An electron transfer strengthened the NO_x binding to the surface by forming nitrite (NO₂^-) or nitrate (NO₃^-) species. The DFT calculations revealed that the RP-type structure promoted NO_x oxidation and storage properties by forming active oxygen due to the Jahn-Teller distortion and by exposing SrO-terminated surfaces due to the cleavage at the rock salt layer.

NO reduction with CO over CuOx/CeO2 nanocomposites: influence of oxygen vacancies and lattice strain

The morphology-dependent population of oxygen vacancies in CuOx/CeO2 nanocomposites used for NO reduction with CO and its pivotal role in the reaction mechanism are examined in this combined experimental and first-principles study.

A first-principles understanding of the CO-assisted NO reduction on the IrRu/Al2O3 catalyst under O2-rich conditions

The IrRu alloy offered optimal energetics for NO reduction by CO. The ensemble effect plays a key role in promoting the reactivity of the IrRu alloy. Making the IrRu surface alloy is better for CO-SCR than forming an alloy over the bulk structure.

Understanding the promotional effect of 3d transition metals (Fe, Co, Cu) on Pd/TiO2 for H2-SCR

The addition of 3d transition metal (Fe, Co, Cu) oxides on Pd/TiO₂ catalysts show that the formation of monodentate nitrates is the rate limiting step in the formation of NH_x species, which is active intermediate for the enhancement of H₂-SCR activities.

New advances in using Raman spectroscopy for the characterization of catalysts and catalytic reactions

Gaining insight into the mode of operation of heterogeneous catalysts is of great scientific and economic interest. Raman spectroscopy has proven its potential as a powerful vibrational spectroscopic technique for a fundamental and molecular-level characterization of catalysts and catalytic reactions. Raman spectra provide important insight into reaction mechanisms by revealing specific information on the catalysts' (defect) structure in the bulk and at the surface, as well as the presence of adsorbates and reaction intermediates. Modern Raman instrumentation based on single-stage spectrometers allows high throughput and versatility in design of in situ/operando cells to study working catalysts. This review highlights major advances in the use of Raman spectroscopy for the characterization of heterogeneous catalysts made during the past decade, including the development of new methods and potential directions of research for applying Raman spectroscopy to working catalysts. The main focus will be on gas-solid catalytic reactions, but (photo)catalytic reactions in the liquid phase will be touched on if it appears appropriate. The discussion begins with the main instrumentation now available for applying vibrational Raman spectroscopy to catalysis research, including in situ/operando cells for studying gas-solid catalytic processes. The focus then moves to the different types of information available from Raman spectra in the bulk and on the surface of solid catalysts, including adsorbates and surface depositions, as well as the use of theoretical calculations to facilitate band assignments and to describe (resonance) Raman effects. This is followed by a presentation of major developments in enhancing the Raman signal of heterogeneous catalysts by use of UV resonance Raman spectroscopy, surface-enhanced Raman spectroscopy (SERS), and shell-isolated nanoparticle surface-enhanced Raman spectroscopy (SHINERS). The application of time-resolved Raman studies to structural and kinetic characterization is then discussed. Finally, recent developments in spatially resolved Raman analysis of catalysts and catalytic processes are presented, including the use of coherent anti-Stokes Raman spectroscopy (CARS) and tip-enhanced Raman spectroscopy (TERS). The review concludes with an outlook on potential future developments and applications of Raman spectroscopy in heterogeneous catalysis.