Defect Sites and Their Distributions on MgO(100) by Li and Ca Adsorption Calorimetry

A comparative study on the morphological features of highly ordered MgO:AgO nanocube arrays prepared via a hydrothermal method

II–VI semiconductor nanotubes are a recently developed class of nanomaterials whose unique photophysical properties are helping to create a new generation of nanomaterials in the field of photonics and microelectronics.

A compact low-temperature single crystal adsorption calorimetry setup for measuring coverage dependent heats of adsorption at cryogenic temperatures

Here we present the modification of an already existing Single Crystal Adsorption Calorimetry (SCAC) apparatus which has been extended by a compact cooling system to measure the coverage dependent heats of adsorption of gaseous compounds on thin metal substrates in a temperature range from 80 K to 430 K. The setup is characterized and its performance is tested by studying the adsorption of CO on Pt(111) at 150 K and 300 K. Coverage dependent sticking probabilities and heat of adsorption measurements are compared to previous experimental and theoretical studies proving the reliability of our compact low-temperature-SCAC setup.

Adsorption calorimetry during metal vapor deposition on single crystal surfaces: increased flux, reduced optical radiation, and real-time flux and reflectivity measurements

Thin films of metals and other materials are often grown by physical vapor deposition. To understand such processes, it is desirable to measure the adsorption energy of the deposited species as the film grows, especially when grown on single crystal substrates where the structure of the adsorbed species, evolving interface, and thin film are more homogeneous and well-defined in structure. Our group previously described in this journal an adsorption calorimeter capable of such measurements on single-crystal surfaces under the clean conditions of ultrahigh vacuum [J. T. Stuckless, N. A. Frei, and C. T. Campbell, Rev. Sci. Instrum. 69, 2427 (1998)]. Here we describe several improvements to that original design that allow for heat measurements with ~18-fold smaller standard deviation, greater absolute accuracy in energy calibration, and, most importantly, measurements of the adsorption of lower vapor-pressure materials which would have previously been impossible. These improvements are accomplished by: (1) using an electron beam evaporator instead of a Knudsen cell to generate the metal vapor at the source of the pulsed atomic beam, (2) changing the atomic beam design to decrease the relative amount of optical radiation that accompanies evaporation, (3) adding an off-axis quartz crystal microbalance for real-time measurement of the flux of the atomic beam during calorimetry experiments, and (4) adding capabilities for in situ relative diffuse optical reflectivity determinations (necessary for heat signal calibration). These improvements are not limited to adsorption calorimetry during metal deposition, but also could be applied to better study film growth of other elements and even molecular adsorbates.

The energetics of supported metal nanoparticles: relationships to sintering rates and catalytic activity

Transition metal nanoparticles on the surfaces of oxide and carbon support materials form the basis for most solid catalysts and electrocatalysts, and have important industrial applications such as fuel production, fuels, and pollution prevention. In this Account, I review my laboratory group's research toward the basic understanding of the effects of particle size and support material on catalytic properties. I focus on studies of well-defined model metal nanoparticle catalysts supported on single-crystalline oxide surfaces. My group structurally characterized such catalysts using a variety of ultrahigh vacuum surface science techniques. We then measured the energies of metal atoms in these supported nanoparticles, using adsorption calorimetry tools that we developed. These metal adsorption energies increase with increasing size of the nanoparticles, until their diameter exceeds about 6 nm. Below 6 nm, the nature of the oxide support surface reaches also greatly affects the metal adsorption energies. Using both adsorption calorimetry and temperature programmed desorption (TPD), we measured the energy of adsorbed catalytic intermediates on metal nanoparticles supported on single crystal oxide surfaces, as a function of particle size. The studies reveal correlations between a number of characteristics. These include the size- and support-dependent energies of metal surface atoms in supported metal nanoparticles, their rates of sintering, how strongly they bind small adsorbates, and their catalytic activity. The data are consistent with the following model: the more weakly the surface metal atom is attached to the nanomaterial, the more strongly it binds small adsorbates. Its strength of attachment to the nanomaterial is dominated by the number of metal-metal bonds which bind it there, but also by the strength of metal/oxide interfacial bonding. This same combination of bond strengths controls sintering rates as well: the less stable a surface metal atom is in the nanomaterial, the greater is the thermodynamic driving force for it to sinter, and the faster is its sintering rate. These correlations provide key insights into how and why specific structural properties of catalyst nanomaterials dictate their catalytic properties. For example, they explain why supported Au catalysts must contain Au nanoparticles smaller than about 6 nm to have high activity for combustion and selective oxidation reactions. Only below about 6 nm are the Au atoms so weakly attached to the catalyst that they bind oxygen sufficiently strongly to enable the activation of O₂. By characterizing this interplay between industrially important rates (of net catalytic reactions, of elementary steps in the catalytic mechanism, and of sintering) and their thermodynamic driving forces, we can achieve a deeper fundamental understanding of supported metal nanoparticle catalysts. This understanding may facilitate development of better catalytic nanomaterials for clean, sustainable energy technologies.

Adsorption microcalorimetry: recent advances in instrumentation and application

Adsorption microcalorimetry measures the energetics of adsorbate-surface interactions and can be performed by use of several different techniques. This review focuses on three methods: single-crystal adsorption calorimetry (SCAC), isothermal titration calorimetry (ITC), and electrochemical adsorption calorimetry. SCAC is a uniquely powerful technique that has been applied to a variety of atoms and molecules that represent a large variety of well-defined adsorbate species on a wide range of single-crystal surfaces. ITC and electrochemical microcalorimetry are useful for studying adsorption energies in liquid solutions (on surfaces of suspended powders) and at the electrode-electrolyte interface, respectively. Knowledge of the energetics of adsorbate formation is valuable to ongoing research in many fields, including catalysis, fuel cells, and solar power. In addition, calorimetric measurements serve as benchmarks for the improvement of computational approaches to understanding surface chemistry. We review instrumentation and applications, emphasizing our own work.