Single Biomolecule Imaging by Electrochemiluminescence

An integrated bipolar electrode with shared cathode for dual-mode detection and imaging of CEA

In this paper, we designed a novel shared cathode bipolar electrode chip based on Ohm 's law and successfully constructed a dual-mode dual-signal biosensor platform (DD-cBPE). The device integrates ELISA, ECL, and ECL imaging to achieve highly sensitive detection and visual imaging of carcinoembryonic antigen (CEA). The unique circuit structure of the device not only realizes the dual signal detection of the target, but also breaks the traditional signal amplification concept. The total resistance of the system is reduced by series-parallel connection of BPE, and the total current in the circuit is increased. In addition, Au@NiCo2O4@MnO2 nanozyme activity probe was introduced into the common cathode to enhance the conductivity of the material. At the same time, due to the excellent peroxidase (POD) activity of NiCo2O4@MnO2, the decomposition of H2O2 was accelerated, so that more electrons flowed to the BPE anode, and finally the dual amplification of the ECL signal was realized. The device affects the current in the circuit by regulating the concentration of the co-reactant TPrA, thereby affecting the resistance of the system. Finally, different luminescent reagents emit light at the same potential and the luminous efficiency is similar. In addition, the chip does not need external resistance regulation, which improves the sensitivity of the immunosensor and meets the needs of timely detection. It provides a new idea for the deviceization of bipolar electrodes and has broad application prospects in biosensors, clinical detection, and environmental monitoring.

DNA tetrahedral scaffold-corbelled self-feedback circuit for dual-mode ratiometric biosensing with Ru@COF-LZU1 accelerator

Sensitive, reliable, and specific detection of microRNAs (miRNAs) is a key objective for disease diagnosis and prognosis. Here, a ratiometric fluorescent/electrochemiluminescent (FL/ECL) sensor was designed for the dual-mode detection of miRNA-122, a hepatocellular carcinoma biomarker. The strong ECL emission was achieved from imine-linked covalent organic framework (COF-LZU1) accelerator enriched Ru(bpy)32+ molecules (Ru@COF-LZU1), which was applied as a delimited reaction micro-reactor to enhance ECL emission. Impressively, to construct an efficient sensing platform, self-feedback circuit was grafted at the vertex of DNA tetrahedral scaffold (DTS), which could provide a solution-phase-like environment and transform miRNA-122 into abundant single-stranded DNAs on the disposable electrode. Simultaneously, the carboxyfluorescein (FAM) tagged DNA segment was cleaved and released into the reaction solution, bringing in the recovery of FL response (FL on). Finally, the introduction of glucose oxidase (GOD) could generate H2O2 by in situ catalyzing GOD to glucose, resulting in the decrease of ECL signal (ECL off). Relying on FL/ECL ratio value, miRNA-122 was quantified with high sensitivity, well selectivity, stability and favorable practicability, suggesting that the proposed biosensor hold great potential for clinical diagnosis.

Electrochemiluminescence assay for the impact of Ganoderma lucidum polysaccharides on resisting arsenic-induced apoptosis

Ganoderma lucidum (G. lucidum) is a traditional edible fungus with strong medicinal value. G. lucidum polysaccharides (GLP) encapsulate many of the key beneficial properties of this species, providing a valuable tool for the treatment of a range of diseases. The present study was developed to explore the protective benefits of GLP treatment in the context of arsenic poisoning. Through microscopy and flow cytometry experiments, NaAsO2 was found to induce rat tracheal epithelial (RTE) cell apoptosis, together with reductions in cell surface epidermal growth factor receptor (EGFR) expression. GLP treatment, however, was able to reduce apoptosis rates and elevate the expression of EGFR relative to NaAsO2-treated cells. GLP extracts (50, 100, 200 mg·mL-1) prepared from four types of G. lucidum were administered to RTE cells damaged with arsenic, revealing limited differences in position resistance among these varieties. This work provides reference for the pharmaceutical and medical research of G. lucidum.

Electroprecipitating the Sulfate Radical Anion Amplifies Electrochemiluminescence in Space and Time

We have discovered a strategy to synthesize reactive radical salts, effectively bottling up radicals in space and time for future use. We apply this new principle to electrochemiluminescence (ECL) through the simultaneous electro-reduction of peroxydisulfate, S2O82-, and tris(bipyridine)ruthenium(II), [Ru(bpy)3]2+ in a water/acetonitrile mixture. The electrode generates a concentration profile exceeding the solubility of the cation and anion pair, promoting precipitation. After the application of a potential, leads are disconnected, and the crystals electrolessly chemiluminesce during dissolution and can be transported to other solutions for later chemiluminescence uses. Our method extends ECL hundreds of micrometers from the electrode surface and increases the ECL lifetime by orders of magnitude. Control experiments, including electron spin resonance, validate the crystallization of SO4•-, allowing detailed mechanistic insight. We demonstrate platform generalizability by precipitating a radical salt made of calcium and SO4•-, and we demonstrate the salt's ability to drive chemiluminescence. Our results emphasize the elegant chemical tenet that extremely reactive radicals can be bottled up as solids to be used as future reagents if precipitation occurs more quickly than the radical lifetime.

Insight into the charge transfer behavior of an electrochemiluminescence sensor based on porphyrin-coumarin derivatives with a donor-acceptor configuration

The excellent photophysical and electrochemical properties of porphyrins have inspired widespread interest in the realm of electrochemiluminescence (ECL). The aggregation-caused deficiency of ECL emission in aqueous solution, however, still severely impedes further applications. Herein, a molecule with a donor-acceptor (D-A) configuration, ATPP-Cou, consisting of monoaminoporphyrin as an electron donor and coumarin as an electron acceptor, was designed as an ECL luminophore to address the susceptibility of the porphyrin to aggregation-caused quenching (ACQ) in aqueous solution. ATPP-Cou demonstrated a three-fold enhanced ECL signal compared to pristine ATPP. Despite the acknowledged significance of intramolecular charge transfer (ICT) in generating excited states in ECL, there is a lack of quantitative descriptions. Herein, intensity-modulated photocurrent spectroscopy (IMPS) and scanning photoelectrochemical microscopy (SPECM) were utilized to validate the influence of ICT on the enhancement performance of D-A type ECL molecules. Additionally, ATPP-Cou was also developed as a probe for the successful detection of Cu2+ in aqueous solution. The present study not only enriches the repertoire of efficient porphyrin-based ECL luminophores applicable in aqueous environments but also exemplifies the successful integration of novel measurement techniques to provide more comprehensive insights into the underlying mechanisms responsible for improved ECL performance.

The tightest self-assembled ruthenium metal-organic framework combined with proximity hybridization for ultrasensitive electrochemiluminescence analysis of paraquat

Metal-organic frameworks (MOFs), as porous materials, have great potential for exploring high-performance electrochemiluminescence (ECL) probes. However, the constrained applicability of MOFs in the realm of ECL biosensing is primarily attributed to their inadequate water stability, which consequently impairs the overall ECL efficiency. Herein, we developed a competitive ECL biosensor based on a novel tightest structural ruthenium-based organic framework emitter combining the proximity hybridization-induced catalytic hairpin assembly (CHA) strategy and the quenching effect between the Ru-MOF and ferrocene for detecting paraquat (PQ). Through a simple hydrothermal synthesis strategy, ruthenium and 2,2'-bipyrimidine (bpm) are head-to-head self-assembled to obtain a novel tightest structural Ru-MOF. Due to the metal-ligand charge-transfer (MLCT) effect between ruthenium and the bpm ligand and the connectivity between the internal chromophore units, the Ru-MOF exhibits strong ECL emissions. Meanwhile, the coordination-driven Ru-MOF utilizes strong metal-organic coordination bonds as building blocks, which effectively solves the problem of serious leakage of chromophores caused by water solubility. The sensitive analysis of PQ is realized in the range of 1 pg/mL to 1 ng/mL with a detection limit of 0.352 pg/mL. The tightest structural Ru-MOF driven by the coordination of ruthenium and bridging ligands (2,2'-bipyrimidine, bpm) provides new horizons for exploring high-performance MOF-based ECL probes for quantitative analysis of biomarkers.

Enhanced Electrochemiluminescence at the Gas/Liquid Interface of Bubbles Propelled into Solution

Electrochemiluminescence (ECL) is typically confined to a micrometric region from the electrode surface. This study demonstrates that ECL emission can extend up to several millimeters away from the electrode employing electrogenerated chlorine bubbles. The mechanism behind this bubble-enhanced ECL was investigated using an Au microelectrode in chloride-containing and chloride-free electrolyte solutions. We discovered that ECL emission at the gas/solution interface is driven by two parallel effects. First, the bubble corona effect facilitates the generation of hydroxyl radicals capable of oxidizing luminol while the bubble is attached to the surface. Second, hypochlorite generated from chlorine sustains luminol emission for over 200 s and extends the emission range up to 5 mm into the solution, following bubble detachment. The new approach can increase the emission intensity of luminol-based assays 5-fold compared to the conventional method. This is demonstrated through a glucose bioassay, using a midrange mobile phone camera for detection. These findings significantly expand the potential applications of ECL by extending its effective range in time and space.

Stereoscopic Imaging of Single Molecules at Plasma Membrane of Single Cell Using Photoreduction-Assisted Electrochemistry

Stereoscopic imaging of single molecules at the plasma membrane of single cell requires spatial resolutions in 3 dimensions (x-y-z) at 10-nm level, which is rarely achieved using most optical super-resolution microscopies. Here, electrochemical stereoscopic microscopy with a detection limit down to a single molecule is achieved using a photoreduction-assisted cycle inside a 20-nm gel electrolyte nanoball at the tip of a nanopipette. On the basis of the electrochemical oxidation of Ru(bpy)3 2+ into Ru(bpy)3 3+ followed by the reduction of Ru(bpy)3 3+ into Ru(bpy)3 2+ by photogenerated isopropanol radicals, a charge of 1.5 fC is obtained from the cycling electron transfers involving one Ru(bpy)3 2+/3+ molecule. By using the nanopipette to scan the cellular membrane modified with Ru(bpy)3 2+-tagged antibody, the morphology of the cell membrane and the distribution of carcinoembryonic antigen (CEA) on the membrane are electrochemically visualized with a spatial resolution of 14 nm. The resultant stereoscopic image reveals more CEA on membrane protrusions, providing direct evidence to support easy access of membrane CEA to intravenous antibodies. The breakthrough in single-molecule electrochemistry at the cellular level leads to the establishment of high-resolution 3-dimensional single-cell electrochemical microscopy, offering an alternative strategy to remedy the imperfection of stereoscopic visualization in optical microscopes.

Dynamic Monitoring of Time-Dependent Evolution of Biomolecules Using Quantum Dots-Based Biosensors Assemblies

The dynamic monitoring of biomolecules that are part of cell membranes generally constitutes a challenge. Electrochemiluminescence (ECL) biosensor assemblies provide clear advantages concerning microscopic imaging. Therefore, this paper proposes and analyzes a quantum dots-based biosensor assembly. Thus, particular attention is granted to biomolecules that are part of cell membranes. Additionally, this paper describes and analyzes a quantum dots-based biosensor assembly, which is used to implement a fully functional color ECL visualization system that allows for cellular and biomolecular structures to be accurately visualized. The related nano-emitter allows the implementation of real-time bioimaging scenarios. Consequently, the proposed approach is thoroughly evaluated relative to the time-dependent evolution of biomolecules. It has been demonstrated that traditionally problematic structures, like the biomolecules that are part of cell membranes, can be studied and monitored relative to their time-dependent dynamic evolution using the proposed solution. The reported research process has been conducted in the realm of cooperation with a specialized biomedical engineering company, and the described results are expected to substantially support a better understanding of the biomolecules' time-dependent dynamic evolution.

Critical Aspects and Challenges in the Design of Small Molecules for Electrochemiluminescence (ECL) Application

Electrochemiluminescence (ECL) has gained renewed interest due to the strong parallel development of luminophores in the field of organic light emitting diodes (OLEDs) with which this technique shares several aspects. In this perspective review we discuss the most relevant advances of the past 15 years in the study of organic and organometallic compounds as ECL emitters, by dividing them in three different classes: i) fluorescent emitters, ii) phosphorescent emitters and iii) Thermally Activated Delayed Fluorescence (TADF) emitters; then, water-soluble organic luminophores will be also discussed. We focus on how their design, their photo- and electrochemical properties and, in particular, the nature of the emitter, affect their efficiency in ECL. Regardless of the type of luminophore or the photoluminescence quantum yield (PLQY), the literature converges on the fact that the most determining aspect is the stability of the oxidized/reduced form of the emitter. Even if phosphorescent emitters can show outstanding efficiency, this often requires the absence of oxygen. In the case of TADFs, there is also a strong dependence of photoluminescence both in terms of PLQY and emission energy on the polarity of the media, so compounds, that appear promising in organic solvents, may be very inefficient in aqueous media.

Pre-Adsorbed H-Mediated Electrochemiluminescence

In conventional electrochemiluminescence (ECL) systems, the presence of the competitive cathodic hydrogen evolution reaction (HER) in aqueous electrolytes is typically considered to be a side reaction, leading to a reduced ECL efficiency and stability due to H2 generation and aggregation at the electrode surface. However, the significant role of adsorbed hydrogen (H*) as a key intermediate, formed during the Volmer reaction in the HER process, has been largely overlooked. In this study, employing the luminol-H2O2 system as a model, we for the first time demonstrate a novel H*-mediated coreactant activation mechanism, which remarkably enhances the ECL intensity. H* facilitates cleavage of the O-O bond in H2O2, selectively generating highly reactive hydroxyl radicals for efficient ECL reactions. Experimental investigations and theoretical calculations demonstrate that this H*-mediated mechanism achieves superior coreactant activation compared to the conventional direct electron transfer pathway, which unveils a new pathway for coreactant activation in the ECL systems.

Highly sensitive and selective demethylase FTO detection using a DNAzyme-mediated CRISPR/Cas12a signal cascade amplification electrochemiluminescence biosensor with C-CN/PCNV heterojunction as emitter

Fat mass and obesity-associated protein (FTO) has gained attention as the first RNA N6-methyladenosine (m6A) modification eraser due to its overexpression being associated with various cancers. In this study, an electrochemiluminescence (ECL) biosensor for the detection of demethylase FTO was developed based on DNAzyme-mediated CRISPR/Cas12a signal cascade amplification system and carboxylated carbon nitride nanosheets/phosphorus-doped nitrogen-vacancy modified carbon nitride nanosheets (C-CN/PCNV) heterojunction as the emitter. The biosensor was constructed by modifying the C-CN/PCNV heterojunction and a ferrocene-tagged probe (ssDNA-Fc) on a glassy carbon electrode. The presence of FTO removes the m6A modification on the catalytic core of DNAzyme, restoring its cleavage activity and generating activator DNA. This activator DNA further activates the trans-cleavage ability of Cas12a, leading to the cleavage of the ssDNA-Fc and the recovery of the ECL signal. The C-CN/PCNV heterojunction prevents electrode passivation and improves the electron-hole recombination, resulting in significantly enhanced ECL signal. The biosensor demonstrates high sensitivity with a low detection limit of 0.63 pM in the range from 1.0 pM to 100 nM. Furthermore, the biosensor was successfully applied to detect FTO in cancer cell lysate and screen FTO inhibitors, showing great potential in early clinical diagnosis and drug discovery.

Electrochemiluminescence Microscopy

Electrochemiluminescence (ECL) is rapidly evolving from an analytical method into an optical microscopy. The orthogonality of the electrochemical trigger and the optical readout distinguishes it from classic microscopy and electrochemical techniques, owing to its near-zero background, remarkable sensitivity, and absence of photobleaching and phototoxicity. In this minireview, we summarize the recent advances in ECL imaging technology, emphasizing original configurations which enable the imaging of biological entities and the improvement of the analytical properties by increasing the complexity and multiplexing of bioassays. Additionally, mapping the (electro)chemical reactivity in space provides valuable information on nanomaterials and facilitates deciphering ECL mechanisms for improving their performances in diagnostics and (electro)catalysis. Finally, we highlight the recent achievements in imaging at the ultimate limits of single molecules, single photons or single chemical reactions, and the current challenges to translate the ECL imaging advances to other fields such as material science, catalysis and biology.

Thickness-Resolved Electrochemiluminescence Microscopy of Extracellular Matrix at Tumor Tissues for Rapid Cancer Diagnosis

The traditional recognition of extracellular matrix (ECM) at tissue sections relies on the time-consuming immunofluorescence that could not meet the demand of rapid diagnosis. Herein, we introduce a thickness-resolved electrochemiluminescence (ECL) microscopy to image thin-layer ECM at tissue sections for fast histopathological analysis. The unique surface-confined ECL mechanism enables to unveil the diversity and complexity of multiple tissue structures with varying thicknesses. Notably, the short lifetimes and the limited diffusion of electrogenerated coreactant radicals combined with their chemical reactivity result in a 2-fold increase in ECL intensity on ECM structures compared to the remaining tissue, enabling ECM visualization without specific labeling. The further quantitation of the ECM localization within tissue sections furnishes crucial insights into tumor progression and, more importantly, differentiates carcinoma and paracancerous tissues from patients in less than 30 min. Moreover, the reported electrochemistry-based microscopy is a dynamic approach allowing to investigate the transport, tortuosity, and trafficking properties through the tissues. This thickness-resolved recognition strategy not only opens new avenues for imaging complex samples but also holds promise for expediting tissue pathologic diagnosis, offering a more automated protocol with enhanced quantitative data compared to current intraoperative pathology methods.

Pyrenetetrasulfonate-grafted 2D ultrathin metal-organic layer as new electrochemiluminescence emitters for ultrasensitive microRNA-21 assay

The exploration of novel electrochemiluminescence (ECL) luminophores with excellent ECL properties is a current research hotspot in the ECL field. Herein, a novel high-efficiency Ru-complex-free ECL emitter PyTS-Zr-BTB-MOL has been prepared by using porous ultrathin Zr-BTB metal-organic layer (MOL) as carrier to coordinatively graft the cheap and easily available polycyclic aromatic hydrocarbon (PAH) derivative luminophore PyTS whose ECL performance has never been investigated. Gratifyingly, the ECL intensity and efficiency of PyTS-Zr-BTB-MOL were markedly enhanced compared to both PyTS monomers and PyTS aggregates. The main reason was that the distance between pyrene rings was greatly expanded after the PyTS grafting on the Zr6 clusters of Zr-BTB-MOL, which overcame the aggregation-caused quenching (ACQ) effect of PyTS and thus enhanced the ECL emission. Meanwhile, the porous nanosheet structure of PyTS-Zr-BTB-MOL could distinctly increase the exposure of PyTS luminophores and shorten the diffusion paths of coreactants and electrons/ions, which effectively promoted the electrochemical excitation of more PyTS luminophores and thus achieved a further ECL enhancement. In light of the remarkable ECL property of PyTS-Zr-BTB-MOL, it was employed as an ECL indicator to build a novel high-sensitivity ECL biosensor for microRNA-21 determination, possessing a satisfactory response range (100 aM to 100 pM) and an ultralow detection limit (10.4 aM). Overall, this work demonstrated that using MOLs to coordinatively graft the PAH derivative luminophores to eliminate the ACQ effect and increase the utilization rate of the luminophores is a promising and efficient strategy to develop high-performance Ru-complex-free ECL materials for assembling ultrasensitive ECL biosensing platforms.

Automatic Electrochemiluminescence Method for the Detection of Cancerous Exosomes Incorporating Specific Aptamer-Magnetic Beads and Signal Nanoprobes

Exosomes, as an emerging biomarker, have exhibited remarkable promise in early cancer diagnosis. Here, a highly sensitive, selective, and automatic electrochemiluminescence (ECL) method for the detection of cancerous exosomes was developed. Specific aptamer-(EK)4 peptide-tagged magnetic beads (MBs-(EK)4-aptamer) were designed as a magnetic capture probe in which the (EK)4 peptide was used to reduce the steric binding hindrance of cancerous exosomes with a specific aptamer. One new universal ECL signal nanoprobe (CD9 Ab-PEG@SiO2ϵRu(bpy)32+) was designed and synthesized by using microporous SiO2 nanoparticles as the carrier for loading ECL reagent Ru(bpy)32+, polyethylene glycol (PEG) layer, and anticluster of differentiation 9 antibody (CD9 Ab). A "sandwich" biocomplex was formed on the surface of the magnetic capture probe after mixing the capture probe, target exosomes, and ECL signal nanoprobe, and then it was introduced into an automated ECL analyzer for rapid and automatic ECL measurement. It was found that the designed signal nanoprobe shows a 270-fold improvement in the signal-to-noise ratio than that of the ruthenium complex-labeled CD9 antibody signal probe. The relative ECL intensity was proportional to MCF-7 exosomes as a model in the range of 102 to 104 particle/μL, with a detection limit of 11 particle/μL. Furthermore, the ECL method was employed to discriminate cancerous exosomes based on fingerprint responses using the designed multiple magnetic capture probes and the universal ECL signal nanoprobe. This work demonstrates that the utilization of a designed automated ECL tactic using the MBs-(EK)4-aptamer capture probe and the CD9 Ab-PEG@SiO2ϵRu(bpy)32+ signal nanoprobe will provide a unique and robust method for the detection and discrimination of cancerous exosomes.

Recent Advances in Electrochemiluminescence Visual Biosensing and Bioimaging

Electrochemiluminescence (ECL) is one of the most powerful techniques that meet the needs of analysis and detection in a variety of scenarios, because of its highly analytical sensitivity and excellent spatiotemporal controllability. ECL combined with microscopy (ECLM) offers a promising approach for quantifying and mapping a wide range of analytes. To date, ECLM has been widely used to image biological entities and processes, such as cells, subcellular structures, proteins and membrane transport properties. In this review, we first introduced the mechanisms of several classic ECL systems, then highlighted the progress of visual biosensing and bioimaging by ECLM in the last decade. Finally, the characteristics of ECLM were summarized, as well as some of the current challenges. The future research interests and potential directions for the application of ECLM were also outlooked.

An Encyclopedic Compendium on Chemosensing Supramolecular Metal-Organic Gels

Chemosensing, an interdisciplinary scientific domain, plays a pivotal role ranging from environmental monitoring to healthcare diagnostics and (inter)national security. Metal-organic gels (MOGs) are recognized for their stability, selectivity, and responsiveness, making them valuable for chemosensing applications. Researchers have explored the development of MOGs based on different metal ions and ligands, allowing for tailored properties and sensitivities, and have even demonstrated their applications as portable sensors such as paper-based test strips for practical use. Herein, several studies related to MOGs development and their applications in the chemosensing field via UV-visible or luminance along with electrochemical approach are presented. These papers explored MOGs as versatile materials with their use in sensing bio or environmental analytes. This review provides a foundational understanding of key concepts, methodologies, and recent advancements in this field, fostering the scientific community.

PdPt@SnS2 Nanosheets for a Novel Ultrasensitive Electrochemiluminescence Biosensor for miRNA-21 Assay

PdPt nanosheets decorated on SnS2 nanosheets (i.e., PdPt@SnS2 NSs) were fabricated for a novel electrochemiluminescence (ECL) biosensor for ultrasensitive detection of miRNA-21 based on catalytic hairpin assembly (CHA) cycles. The PdPt@SnS2 NSs serve as both the main luminophore and a highly effective coreaction accelerator in the ECL biosensor. In the CHA cycles, more miRNA-21 is captured, and the performance of the ECL biosensor is improved. When miRNA-21 is present, the hairpin chain DNA1 (i.e., H1) is opened, and the ferrocene (Fc)-modified hairpin chain DNA2 (i.e., Fc-H2) hybridizes with as-opened H1 by replacing miRNA-21 to stimulate CHA cycles of miRNA-21. During the CHA cycles, Fc-H2 quenches the ECL signal to monitor miRNA-21. As a result, the ECL biosensor shows ultrasensitive and highly selective detection of miRNA-21 from 1 aM to 1 nM with a detection limit (LOD) of 0.02 aM. In addition, the ECL biosensor exhibits excellent practicality for miRNA-21 detection in human serum samples.

Shadow electrochemiluminescence imaging of giant liposomes opening at polarized electrodes

In this work, the release of giant liposome (∼100 μm in diameter) content was imaged by shadow electrochemiluminescence (ECL) microscopy. Giant unilamellar liposomes were pre-loaded with a sucrose solution and allowed to sediment at an ITO electrode surface immersed in a solution containing a luminophore ([Ru(bpy)3]2+) and a sacrificial co-reactant (tri-n-propylamine). Upon polarization, the electrode exhibited illumination over its entire surface thanks to the oxidation of ECL reagents. However, as soon as liposomes reached the electrode surface, dark spots appeared and then spread over time on the surface. This observation reflected a blockage of the electrode surface at the contact point between the liposome and the electrode surface, followed by the dilution of ECL reagents after the rupture of the liposome membrane and release of its internal ECL-inactive solution. Interestingly, ECL reappeared in areas where it initially faded, indicating back-diffusion of ECL reagents towards the previously diluted area and thus confirming liposome permeabilization. The whole process was analyzed qualitatively and quantitatively within the defined region of interest. Two mass transport regimes were identified: a gravity-driven spreading process when the liposome releases its content leading to ECL vanishing and a diffusive regime when ECL recovers. The reported shadow ECL microscopy should find promising applications for the imaging of transient events such as molecular species released by artificial or biological vesicles.

Electrochemiluminescent evaluation of GLUT4 expression in rat adipocytes induced by Ganoderma lucidum polysaccharides

Glucose transporter 4 (GLUT4) directly facilitates cellular uptake of glucose and plays a crucial role in mammalian adipose tissue glucose metabolism. In this work, we constructed a cytosensor for sensitive electrochemiluminescence (ECL) detection of GLUT4 in rat adipocytes (RA cells). A carbon nanotube sponge (CNTSP) was selected to fabricate a permeable electrode to overcome the steric hindrance of cells on the electrode. The expression of GLUT4 after treatment with Ganoderma lucidum polysaccharide (GLP) was assessed by analyzing the luminescence emitted from cell-surface ECL probes. Our preliminary results suggest that GLP promote the expression of GLUT4, thereby enhancing the uptake of the fluorescent glucose 2-NBDG. Treatment with GLP affected GLUT4 expression in RA cells in a dose-dependent manner. Additionally, the ECL cytosensor contributes to the development of ECL imaging of receptors on the cell surface for clinical drug evaluation.

From theory to practice: understanding the challenges in the implementation of electrogenerated chemiluminescence for analytical applications

Electrogenerated chemiluminescence (ECL) stands out as a remarkable phenomenon of light emission at electrodes initiated by electrogenerated species in solution. Characterized by its exceptional sensitivity and minimal background optical signals, ECL finds applications across diverse domains, including biosensing, imaging, and various analytical applications. This review aims to serve as a comprehensive guide to the utilization of ECL in analytical applications. Beginning with a brief exposition on the theory at the basis of ECL generation, we elucidate the diverse systems employed to initiate ECL. Furthermore, we delineate the principal systems utilized for ECL generation in analytical contexts, elucidating both advantages and challenges inherent to their use. Additionally, we provide an overview of different electrode materials and novel ECL-based protocols tailored for analytical purposes, with a specific emphasis on biosensing applications.

Enhanced Aggregation-Induced Delayed Electrochemiluminescence Triggered by Spatial Perturbation of Organic Dots

Development of highly efficient, heavy-metal-free electrochemiluminescence (ECL) materials is attractive but still challenging. Herein, we report an aggregation-induced delayed ECL (AIDECL) active organic dot (OD) composed of a tert-butoxy-group-substituted benzophenone-dimethylacridine compound, which shows high ECL efficiency. The resultant ODs exhibit 2.1-fold higher ECL efficiency compared to control AIDECL-active ODs. Molecular stacking combined with theoretical calculations suggests that tert-butoxy groups effectively participate in the intermolecular interactions, further inhibiting the molecular motions in the aggregated states and thus accelerating radiative decay. On the basis of these ODs exhibiting excellent ECL performance, a proof-of-concept biosensor is constructed for the detection of miR-16 associated with Alzheimer's disease, which demonstrates excellent detection ability with the limit of detection of 1.7 fM. This work provides a new approach to improve the ECL efficiency and enriches the fundamental understanding of the structure-property relationship.

Logic Signal Amplification System for Sensitive Electrochemiluminescence Detection and Subtype Identification of Cancer Cells

Achieving sensitive detection and accurate identification of cancer cells is vital for diagnosing and treating the disease. Here, we developed a logic signal amplification system using DNA tetrahedron-mediated three-dimensional (3D) DNA nanonetworks for sensitive electrochemiluminescence (ECL) detection and subtype identification of cancer cells. Specially designed hairpins were integrated into DNA tetrahedral nanostructures (DTNs) to perform a catalytic hairpin assembly (CHA) reaction in the presence of target microRNA, forming hyperbranched 3D nanonetworks. Benefiting from the "spatial confinement effect," the DNA tetrahedron-mediated catalytic hairpin assembly (DTCHA) reaction displayed significantly faster kinetics and greater cycle conversion efficiency than traditional CHA. The resulting 3D nanonetworks could load a large amount of Ru(phen)32+, significantly enhancing its ECL signal, and exhibit detection limits for both miR-21 and miR-141 at the femtomolar level. The biosensor based on modular logic gates facilitated the distinction and quantification of cancer cells and normal cells based on miR-21 levels, combined with miR-141 levels, to further identify different subtypes of breast cancer cells. Overall, this study provides potential applications in miRNA-related clinical diagnostics.

Electrochemiluminescence-Based Single-Particle Tracking of the Biomolecules Moving along Intercellular Membrane Nanotubes between Live Cells

Electrochemiluminescence (ECL) imaging, a rapidly evolving technology, has attracted significant attention in the field of cellular imaging. However, its primary limitation lies in its inability to analyze the motion behaviors of individual particles in live cellular environments. In this study, we leveraged the exceptional ECL properties of quantum dots (QDs) and the excellent electrochemical properties of carbon dots (CDs) to develop a high-brightness ECL nanoprobe (CDs-QDs) for real-time ECL imaging between living cells. This nanoprobe has excellent signal-to-noise ratio imaging capabilities for the single-particle tracking (SPT) of biomolecules. Our finding elucidated the enhanced ECL mechanism of CDs-QDs in the presence of reactive oxygen species through photoluminescence, electrochemistry, and ECL techniques. We further tracked the movement of single particles on membrane nanotubes between live cells and confirmed that the ECL-based SPT technique using CD-QD nanoparticles is an effective approach for monitoring the transport behaviors of biomolecules on membrane nanotubes between live cells. This opens a promising avenue for the advancement of ECL-based single-particle detection and the dynamic quantitative imaging of biomolecules.

Self-Assembly-Induced Enhancement of Cathodic Electrochemiluminescence of Copper Nanoclusters for a Split-Type Matrix Metalloproteinase 14 Sensing Platform

The unique optoelectronic and tunable luminescent characteristics of copper nanoclusters (Cu NCs) make them extremely promising as luminophores. However, the limited luminescence intensity and stability of Cu NCs have restricted their application in the field of electrochemiluminescence (ECL). Herein, a self-assembly-induced enhancement strategy was successfully employed to enhance the cathodic ECL performance of flexible ligand-stabilized Cu NCs. Specifically, Cu NCs form ordered sheetlike structures through intermolecular force. The restriction of ligand torsion in this self-assembled structure leads to a significant improvement in the ECL properties of the Cu NCs. Experimental results demonstrate that the assembled nanoscale Cu NC sheets exhibit an approximately three-fold increase in cathodic ECL emission compared to the dispersed state of Cu NCs. Furthermore, assembled nanoscale Cu NCs sheets were utilized as signal probes in conjunction with a specific short peptide derived from the catalytic structural domain of matrix metalloproteinase 14 (MMP 14) as the identification probe, thereby establishing a split-type ECL sensing platform for the quantification of NMP 14. The investigation has revealed the exceptional performance of assembled nanoscale Cu NCs sheets in ECL analysis, thus positioning them as novel and promising signal probes with significant potential in the field of sensing.

Femtoliter oil droplets act as CO2 micropumps for uninterrupted electrochemiluminescence at the water|oil interface

Interfacial effects are well-known to significantly alter chemical reactivity, especially in confined environments, where the surface to volume ratio increases. Here, we observed an inhomogeneity in the electrogenerated chemiluminescence (ECL) intensity decrease over time in a multiphasic system composed of femtoliter water droplets entrapping femtoliter volumes of the 1,2-dichloroethane (DCE) continuous phase. In usual electrochemiluminescence (ECL) reactions involving an ECL chromophore and oxalate ([C2O4]2-), the build-up of CO2 diminishes the ECL signal with time because of bubble formation. We hypothesised that relative solubilities of chemical species in these environments play a dramatic role in interfacial reactivity. Water droplets, loaded with the ECL luminophore [Ru(bpy)3]2+ and the coreactant [C2O4]2- were allowed to stochastically collide and adsorb at the surface of a glassy carbon macroelectrode. When water droplets coalesce on the surface, they leave behind femtoliter droplets of the DCE phase (inclusions). We report the surprising finding that the addition of multiple interfaces, due to the presence of continuous phase's femtoliter inclusions, allows sustained ECL over time after successive potential applications at the triple-phase boundary between water droplet|electrode|DCE inclusion. When femtoliter droplets of DCE form on the electrode surface, bright rings of ECL are observed during the simultaneous oxidation of [Ru(bpy)3]2+ and [C2O4]2-. Control experiments and finite element modelling allowed us to propose that these rings arise because CO2 that is generated near the 1,2-dichloroethane droplet partitions in due to relative solubility of CO2 in 1,2-dichloroethane and builds up and/or is expelled at the top of the droplet. The small droplets of the DCE phase act as micropumps, pumping away carbon dioxide from the interface. These results highlight the unexpected point that confined microenvironments and their geometry can tune chemical reactions of industrial importance and fundamental interest.

Timescale correlation of shallow trap states increases electrochemiluminescence efficiency in carbon nitrides

Highly efficient interconversion of different types of energy plays a crucial role in both science and technology. Among them, electrochemiluminescence, an emission of light excited by electrochemical reactions, has drawn attention as a powerful tool for bioassays. Nonetheless, the large differences in timescale among diverse charge-transfer pathways from picoseconds to seconds significantly limit the electrochemiluminescence efficiency and hamper their broad applications. Here, we report a timescale coordination strategy to improve the electrochemiluminescence efficiency of carbon nitrides by engineering shallow electron trap states via Au-N bond functionalization. Quantitative electrochemiluminescence kinetics measurements and theoretic calculations jointly disclose that Au-N bonds endow shallow electron trap states, which coordinate the timescale of the fast electron transfer in the bulk emitter and the slow redox reaction of co-reagent at diffusion layers. The shallow electron trap states ultimately accelerate the rate and kinetics of emissive electron-hole recombination, setting a new cathodic electrochemiluminescence efficiency record of carbon nitrides, and empowering a visual electrochemiluminescence sensor for nitrite ion, a typical environmental contaminant, with superior detection range and limit.

Plasmonic Imaging of Single DNA with Charge Sensitive Monolayer WS2

Imaging the surface charge of biomolecules such as proteins and DNA, is crucial for comprehending their structure and function. Unfortunately, current methods for label-free, sensitive, and rapid imaging of the surface charge of single DNA molecules are limited. Here, we propose a plasmonic microscopy strategy that utilizes charge-sensitive single-crystal monolayer WS2 materials to image the local charge density of a single λ-DNA molecule. Our study reveals that WS2 is a highly sensitive charge-sensitive material that can accurately measure the local charge density of λ-DNA with high spatial resolution and sensitivity. The consistency of the surface charge density values obtained from the single-crystal monolayer WS2 materials with theoretical simulations demonstrates the reliability of our approach. Our findings suggest that this class of materials has significant implications for the development of label-free, scanning-free, and rapid optical detection and charge imaging of biomolecules.

Unveiling the Dynamic Electrocatalytic Activity of Online Synthesized Bimetallic Nanocatalysts via Electrochemiluminescence Microscopy

Effective bimetallic nanoelectrocatalysis demands precise control of composition, structure, and understanding catalytic mechanisms. To address these challenges, we employ a two-in-one approach, integrating online synthesis with real-time imaging of bimetallic Au@Metal core-shell nanoparticles (Au@M NPs) via electrochemiluminescence microscopy (ECLM). Within 120 s, online electrodeposition and in situ catalytic activity screening alternate. ECLM captures transient faradaic processes during potential switches, visualizes electrochemical processes in real-time, and tracks catalytic activity dynamics at the single-particle level. Analysis using ECL photon flux density eliminates size effects and yields quantitative electrocatalytic activity results. Notably, a nonlinear activity trend corresponding to the shell metal to Au surface atomic ratio is discerned, quantifying the optimal surface component ratio of Au@M NPs. This approach offers a comprehensive understanding of catalytic behavior during the deposition process with high spatiotemporal resolution, which is crucial for tailoring efficient bimetallic nanocatalysts for diverse applications.

Insulator-on-Conductor Fouling Amplifies Aqueous Electrolysis Rates

The chemical industry is a major consumer of fossil fuels. Several chemical reactions of practical value proceed with the gain or loss of electrons, opening a path to integrate renewable electricity into chemical manufacturing. However, most organic molecules have low aqueous solubility, causing green and cheap electricity-driven reactions to suffer from intrinsically low reaction rates in industry's solvent of choice: water. Here, we show that a strategic, partial electrode fouling with hydrophobic insulators (oils and plastics) offsets kinetic limitations caused by poor reactant solubility, opening a new path for the direct integration of renewable electricity into the production of commodity chemicals. Through electrochemiluminescence microscopy, we reveal for the oxidation of organic reactants up to 6-fold reaction rate increase at the "fouled" oil-electrolyte-electrode interface relative to clean electrolyte-electrode areas. Analogously, electrodes partially masked (fouled) with plastic patterns, deposited either photolithographically (photoresists) or manually (inexpensive household glues and sealants), outperform clean electrodes. The effect is not limited to reactants of limited water solubility, and, for example, net gold electrodeposition rates are up to 22% larger at fouled than clean electrodes. In a system involving a surface-active reactant, rate augmentation is driven by the synergy between insulator-confined reactant enrichment and insulator-induced current crowding, whereas only the latter and possibly localized decrease in iR drop near the insulator are relevant in a system composed of non-surface-active species. Our counterintuitive electrode design enhances electrolysis rates despite the diminished area of intimate electrolyte-electrode contact and introduces a new path for upscaling aqueous electrochemical processes.

Ultrastable Anion Radicals in Ligand-Dimerized Frameworks for Self-Accumulated Electrochemiluminescence

Electrochemiluminescence (ECL) is a light-emitting process that occurs via an annihilation reaction among energetic radical intermediates, whose stabilities determine the ECL efficiency. In this study, a ligand-dimerized metal-organic framework (MOF) with ultrastable anion radical is designed as an efficient nanoemitter for self-accumulated ECL. Due to the nonplanar structure of perylene diimide (PDI) derivate, two PDI ligands in the framework form a J-dimer unit with a vertical distance of ∼5.74 Å. In cathodic scanning, the ligand-dimerized MOF demonstrates three-step ECL emissions with a gradual increase in ECL intensity. Unlike the decrease in the PDI ligand, the self-accumulated ECL of the MOF was observed with 16.8-fold enhancement due to the excellent stability of radical intermediates in frameworks. Electron paramagnetic resonance demonstrated the ultrastability of free radicals in the designed frameworks, with 82.2% remaining even after one month of storage. Density functional theory calculations supported that PDI dimerization was energetically favorable upon successive electron injection. Moreover, the ECL wavelength is 610 nm, corresponding to the emission of excited dimers. The radical-stabilized reticular nanoemitters open up a new platform for decoding the fundamentals of self-accumulated ECL systems.

Novel immunosensor based on electrochemiluminescence inner filter effect and static quenching between fibrillary Ag-MOGs and SiO2@PANI@AuNPs for enabling the sensitive detection of neuron-specific enolase

Metal-organic gels (MOGs) are unique supramolecular gels that are convenient to synthesize. In this work, a cathodic electrochemiluminescence (ECL) system based on Ag-MOGs as a luminophore and K2S2O8 as a co-reactor was developed. The ECL spectrum of the Ag-MOGs overlapped significantly with the strong UV-Vis spectrum of the SiO2@PANI@AuNPs, which effectively quenched the ECL luminescence of the Ag-MOGs. Relying on the inner filter effect between Ag-MOGs and SiO2@PANI@AuNPs, a novel ECL-IFE immunosensor was developed for the detection of neuron-specific enolase (NSE). Under optimal conditions, the ECL signal of the immunosensor displayed excellent linearity over the NSE concentration range of 10 fg/mL-100 ng/mL. The limit of detection (LOD) was 2.6 fg/mL (S/N = 3) with a correlation coefficient R2 of 0.9975. The ECL immunosensor also exhibited excellent stability and reproducibility for the detection of NSE. The results reported provide a feasible concept for the development analytical methods for the detection of other clinically relevant biomarkers.

Coupled Poly(ethylenimine) Coreactant to Enhance Electrochemiluminescence of Polymer Dots for Array Imaging of Protein Biomarkers

Traditional electrochemiluminescent (ECL) bioanalysis suffers from the demand for excessive external coreactants and the damage of reaction intermediates. In this work, a poly(ethylenimine) (PEI)-coupled ECL emitter was proposed by covalently coupling tertiary amine-rich PEI to polymer dots (Pdots). The coupled PEI might act as a highly efficient coreactant to enhance the ECL emission of Pdots through intramolecular electron transfer, reducing the electron transfer distance between emitter and coreactant intermediates and avoiding the disadvantages of traditional ECL systems. Through modification of the PEI-Pdots with tDNA, a sequence partially complementary to cDNA that was complementary to the aptamer of target protein biomarker (aDNA), tDNA-PEI-Pdots were obtained. The biosensors were produced using Au/indium tin oxide (ITO) with an aDNA/cDNA hybrid, and an ECL imaging biosensor array was constructed for ultrasensitive detection of protein biomarkers. Using vascular endothelial growth factor 165 (VEGF165) as a protein model, the proposed ECL imaging method containing two simple incubations with target samples and then tDNA-PEI-Pdots showed a detectable range of 1 pg mL-1 to 100 ng mL-1 and a detection limit of 0.71 pg mL-1, as well as excellent performance such as low toxicity, high sensitivity, excellent selectivity, good accuracy, and acceptable fabrication reproducibility. The PEI-coupled Pdots provide a new avenue for the design of ECL emitters and the application of ECL imaging in disease biomarker detection.

Electrochemiluminescence of iridium(III)/ruthenium(II) complexes with naphthyl tags in solutions and host-guest thin films

Herein we report electrochemiluminescence (ECL) generation from three new iridium(III)/ruthenium(II) (Ir(III)/Ru(II)) complexes with naphthyl (nap) tags in solutions and host-guest thin films. In comparison with its parent structure, the addition of a nap tag to [4-(2-naphthalenyl)-1,10-phenanthroline]bis(2,2'-bipyridine)ruthenium(II) results in a 6.1-fold enhancement in the ECL efficiency. Moreover, the nap tag enables the non-covalent immobilization of Ir(III)/Ru(II) complexes via host-guest interactions. Therefore, a molecular thin film was constructed by hydrophobic effects between the cavity of β-cyclodextrin and the nap tags, which emits stable and strong ECL emission in the presence of tri-n-propylamine (TPrA). These results give a mechanistic insight into ECL generation from (Ir(III)/Ru(II)) complexes with host-guest recognition tags and may help in the development of host-guest thin film-based ECL sensors.

Controllable and Low-Loss Electrochemiluminescence Waveguide Supported by a Micropipette Electrode

One-dimensional molecular crystal waveguide (MCW) can transmit self-generated electrochemiluminescence (ECL), but heavy optical loss occurs because of the small difference in the refractive index between the crystal and its surroundings. Herein, we report a micropipette electrode-supported MCW (MPE/MCW) for precisely controlling the far-field transmission of ECL in air with a low optical loss. ECL is generated from one terminal of the MCW positioned inside the MPE, which is transmitted along the MCW to the other terminal in air. In comparison with conventional waveguides on solid substrates or in solutions, the MPE/MCW is propitious to the total internal reflection of light at the MCW/air interface, thus confining the ECL efficiently in MCW and improving the waveguide performance with an extremely low-loss coefficient of 4.49 × 10-3 dB μm-1. Moreover, by regulation of the gas atmosphere, active and passive waveguides can be resolved simultaneously inside MPE and in air. This MPE/MCW offers a unique advantage of spatially controlling and separating ECL signal readout from its generation, thus holding great promise in biosensing without or with less electrical/chemical disturbance.

Pyrenecarboxaldehyde@Graphene Oxide Acted as a Highly Efficient ECL Emitter and Target-Triggered the Recyclable Cascade System as an Amplifier for Ultrasensitive APE1 Activity Detection

Herein, pyrenecarboxaldehyde@graphene oxide (Pyc@GO) sheets with highly efficient electrochemiluminescence (ECL) as emitters were prepared by a noncovalent combination to develop a neoteric ECL biosensing platform for the ultrasensitive assessment of human apurinic/apyrimidinic endonuclease1 (APE1) activity. Impressively, the pyrenecarboxaldehyde (Pyc) molecules were able to form stable polar functional groups on the surface of GO sheets through the noncovalent π-π stacking mechanism to prevent intermolecular restacking and simultaneously generate Pyc@GO sheets. Compared with the tightly packed PAH nanocrystals, the Pyc@GO sheets significantly reduced internal filtering effects and diminished nonactivated emitters to enhance ECL intensity and achieve strong ECL emission. Furthermore, the APE1-activated initiators could trigger the recyclable cascade amplified system based on the synergistic cross-activation between catalytic hairpin assembly (CHA) and DNAzyme, which improved the signal amplification and transduction ability. Consequently, the developed ECL platform for the detection of APE1 activity displayed exceptional sensitivity with a low detection limit of 4.6 × 10-9 U·mL-1 ranging from 10-8 to 10-2 U·mL-1. Therefore, the proposed strategy holds great promise for the future development of sensitive and reliable biosensing platforms for the detection of various biomarkers.

ZnO nanostructures: A promising frontier in immunosensor development

This review addresses the design of immunosensors, which employ ZnO nanostructures. Various methods of modifying ZnO nanostructures with antibodies or antigens are discussed, including covalent and non-covalent approaches and cross-linking techniques. Immunosensors based on different properties of ZnO nanomaterials are described and compared. This article provides a comprehensive review of electrochemical immunosensors based on ZnO nanostructures and various detection techniques, including cyclic voltammetry (CV), differential pulse voltammetry (DPV), photoelectrochemical (PEC) detection, electrochemical impedance spectroscopy (EIS), and other electrochemical methods. In addition, this review article examines the application of optical detection techniques, including photoluminescence (PL) and electrochemiluminescence (ECL), in the development of immunosensors based on ZnO nanostructures.

Infrared photoinduced electrochemiluminescence microscopy of single cells

Electrochemiluminescence (ECL) is evolving rapidly from a purely analytical technique into a powerful microscopy. Herein, we report the imaging of single cells by photoinduced ECL (PECL; λem = 620 nm) stimulated by an incident near-infrared light (λexc = 1050 nm). The cells were grown on a metal-insulator-semiconductor (MIS) n-Si/SiOx/Ir photoanode that exhibited stable and bright PECL emission. The large anti-Stokes shift allowed for the recording of well-resolved images of cells with high sensitivity. PECL microscopy is demonstrated at a remarkably low onset potential of 0.8 V; this contrasts with classic ECL, which is blind at this potential. Two imaging modes are reported: (i) photoinduced positive ECL (PECL+), showing the cell membranes labeled with the [Ru(bpy)3]2+ complex; and (ii) photoinduced shadow label-free ECL (PECL-) of cell morphology, with the luminophore in the solution. Finally, by adding a new dimension with the near-infrared light stimulus, PECL microscopy should find promising applications to image and study single photoactive nanoparticles and biological entities.

Chemical-chemical redox cycling for improving the sensitivity of the fluorescent assay: A proof-of-concept towards DNA methylation detection

Ultrasensitive analytical methods are still urgent for the discovery of trace level biomarkers and the early clinical diagnosis of disease. In this work, an ultrasensitive universal sensing platform was constructed by integrating fluorescent assay with chemical-chemical redox cycling signal amplification strategy. Using Ru@SiO2 nanoparticles wrapped by MnO2 nanosheets (Ru@SiO2@MnO2) as fluorescent probe, the chemical-chemical redox cycling system was conducted upon ascorbic acid (AA) and tris(2-carboxyethyl)phosphine (TCEP) as reductants and MnO2 nanosheets as oxidant. The MnO2 nanosheets not only could quench the fluorescence of Ru@SiO2 nanoparticles to reduce the background, but also could serve as oxidants to react with AA, generating dehydroascorbic acid (DHA). The DHA was reduced by TCEP in turn to form AA that participated in the next cycling of chemical-chemical redox reaction. Thus, the constantly released AA from the chemical-chemical redox cycling system could massively etch MnO2 nanosheets on Ru@SiO2 surface, making the fluorescence of Ru@SiO2 nanoparticles greatly recovered. It was shown that the sensitivity of the fluorescent assay was improved almost 52 times by utilizing the chemical-chemical redox cycling signal amplification strategy. This strategy was further employed to detect DNA methylation with the aid of AA-encapsulated liposomes that were modified with 5 mC antibodies to bind with the methylated DNA captured in 96-well plate. A detection of limit down to 16.2 fM was achieved for the detection of methylated DNA. It's believed that the incorporation of chemical-chemical redox cycling signal amplification strategy into fluorescent sensing paves a new way for ultrasensitive detection of biomarkers.

Enhancing electrochemiluminescence by modifying Fe3CuO4 and CdS@ZnS: A novel ECL sensor for highly sensitive detection of permethrin

A novel electrochemiluminescence (ECL) sensor was constructed for the detection of permethrin by modifying Fe3CuO4-Ru(bpy)32+ and GO-CdS@ZnS on the electrode. Fe3CuO4 was used as a carrier to adsorb more luminous reagent Ru(bpy)32+ to promote luminescence. Meanwhile, it also can be used as a co-reaction promoter to amplify the initial signal of Ru(bpy)32+-tri-n-propylamine (TPrA) system. When GO-CdS@ZnS was introduced into this system, the ECL signal was further enhanced. The porous nature of graphene oxide (GO) was utilized to load a large amount of CdS@ZnS, in which CdS@ZnS acted as the co-reactant to amplify the ECL signal. The amount of permethrin (PMT) increased and the ECL signal decreased. Under the optimum conditions, the ECL response was linearly related to the logarithm of PMT concentration. The developed ECL sensor allowed for sensitive determination of PMT and exhibited a wide linear range from 1.0 × 10-11 mol L-1 to 1.0 × 10-7 mol L-1. The limit of detection was 3.3 × 10-12 mol L-1 (S/N = 3). It can be used for the detection of PMT in vegetable samples.

An Alternating Current Electroosmotic Flow-Based Ultrasensitive Electrochemiluminescence Microfluidic System for Ultrafast Monitoring, Detection of Proteins/miRNAs in Unprocessed Samples

Early diagnosis of acute diseases is restricted by the sensitivity and complex process of sample treatment. Here, an ultrasensitive, rapid, and portable electrochemiluminescence-microfluidic (ECL-M) system is described via sandwich-type immunoassay and surface plasmonic resonance (SPR) assay. Using a sandwich immunoreaction approach, the ECL-M system employs cardiac troponin-I antigen (cTnI) as a detection model with a Ru@SiO2 NPs labeled antibody as the signal probe. For miR-499-5p detection, gold nanoparticles generate SPR effects to enhance Ru(bpy)3 2+ ECL signals. The system based on alternating current (AC) electroosmotic flow achieves an LOD of 2 fg mL-1 for cTnI in 5 min and 10 aM for miRNAs in 10 min at room temperature. The point-of-care testing (POCT) device demonstrated 100% sensitivity and 98% specificity for cTnI detection in 123 clinical serum samples. For miR-499-5p, it exhibited 100% sensitivity and 97% specificity in 55 clinical serum samples. Continuous monitoring of these biomarkers in rats' saliva, urine, and interstitial fluid samples for 48 hours revealed observations rarely documented in biotic fluids. The ECL-M POCT device stands as a top-performing system for ECL analysis, offering immense potential for ultrasensitive, rapid, highly accurate, and facile detection and monitoring of acute diseases in POC settings.

Ultrasensitive Electrochemiluminescence Biosensor to Detect Ampicillin Resistance Gene (ARGAMP) Based on a Novel Near-Infrared Ruthenium Carbene Complex/TPrA/PEI Ternary ECL System

The establishment of rapid target identification and analysis methods for antibiotic resistance genes (ARGs) is urgently needed. In this study, we unprecedently designed a target-catalyzed hairpin assembly (CHA) electrochemiluminescent (ECL) biosensor for the ultrasensitive detection of ampicillin resistance genes (ARGAMP) based on a novel, efficient near-infrared ruthenium carbene complex/TPrA/PEI ternary ECL system with low oxidation potential. The ternary NIR-ECL system illustrated in this work displayed double ECL intensity in comparison with their corresponding traditional binary ECL system. The as-prepared ECL biosensor illustrated in this work demonstrates highly selective and sensitive determination of ARGAMP from 1 fM to 1 nM and a low detection limit of 0.23 fM. Importantly, it also exhibits good accuracy and stabilities to identify ARGAMP in plasmid and bacterial genome DNA, which demonstrates its excellent reliability and great potential in detecting ARGAMP in real environmental samples.

All-Optical Electrochemiluminescence at Metal-Insulator-Semiconductor Diodes

Pt/InGa/n-Si/SiOx/Pt devices were prepared by using standard chemical and sputtering processes. These systems are diodes comprising a frontside photoactive metal-insulator-semiconductor (MIS) n-Si/SiOx/Pt junction and a backside Pt/InGa/n-Si Ohmic contact. Pt/InGa/n-Si/SiOx/Pt was first characterized by dark-solid-state electrical and impedance measurements. Then, each side of the device was investigated by electrochemical means in the dark and under near-IR illumination at 850 nm in the luminol-H2O2 electrochemiluminescence (ECL) electrolyte. The results suggested the possibility of triggering an all-optical ECL (AO-ECL) at Pt/InGa/n-Si/SiOx/Pt. This was confirmed by studying AO-ECL at the monolithic, all-integrated Pt/InGa/n-Si/SiOx/Pt device, immersed in the ECL electrolyte. The conversion process can occur with good stability and the intensity of the visible emission (440 nm) depends on tunable parameters such as the illumination power density, O2 concentration, or the concentration of added H2O2. These results are important for the next developments of AO-ECL in sensing and microscopy.

Dual-Signal Imaging Mode Based on Fluorescence and Electrochemiluminescence for Ultrasensitive Visualization of SARS-CoV-2 Spike Protein

Accurate and reliable detection of SARS-CoV-2 is critical for the effective prevention and rapid containment of COVID-19. Current approaches suffer from complex procedures or a single signal readout, resulting in an increased risk of false negatives and low sensitivity. Here, we developed a fluorescence (FL) and electrochemiluminescence (ECL) dual-mode imaging platform based on a self-powered DNAzyme walker to achieve accurate surveillance of SARS-CoV-2 spike protein at the single-molecule level. The specific activation of the DNAzyme walker by the target protein provides the power for the system's continuous running, enabling the simultaneous recording of the reduction in fluorescence spots and the appearance of ECL spots generated by the Ru-doped metal-organic framework (MOF) emitter. Therefore, the constructed imaging platform can achieve dual-mode detection of spike protein via reverse dual-signal feedback, which could effectively eliminate false-positive or false-negative signals and improve the detection accuracy and sensitivity with a low detection limit. In particular, the dual-mode accuracy of spike protein diagnosis in samples has been significantly improved compared to single-signal output means. In addition, this dual-mode imaging platform may become a prospective diagnostic device for other infectious viruses.

Optics Determines the Electrochemiluminescence Signal of Bead-Based Immunoassays

Electrochemiluminescence (ECL) is an optical readout technique that is successfully applied for the detection of biomarkers in body fluids using microbead-based immunoassays. This technology is of utmost importance for in vitro diagnostics and thus a very active research area but is mainly focused on the quest for new dyes and coreactants, whereas the investigation of the ECL optics is extremely scarce. Herein, we report the 3D imaging of the ECL signals recorded at single microbeads decorated with the ECL labels in the sandwich immunoassay format. We show that the optical effects due to the light propagation through the bead determine mainly the spatial distribution of the recorded ECL signals. Indeed, the optical simulations based on the discrete dipole approximation compute rigorously the electromagnetic scattering of the ECL emission by the microbead and allow for reconstructing the spatial map of ECL emission. Thus, it provides a global description of the ECL chemical reactivity and the associated optics. The outcomes of this 3D imaging approach complemented by the optical modeling provide insight into the ECL optics and the unique ECL chemical mechanism operating on bead-based immunoassays. Therefore, it opens new directions for mechanistic investigations, ultrasensitive ECL bioassays, and imaging.

Amplification of an Electrochemiluminescence-Emissive Aptamer into DNA Nanotags for Sensitive Fecal Calprotectin Determination

The precision additive manufacturing and tessellated multitasking out of the structural DNA nanotechnology enable a configurable expression of densified electrochemiluminescent (ECL) complexes, which would streamline the bioconjugation while multiplying signals. Herein, a completely DNA-scaffold ECL "polyploid" was replicated out via the living course of rolling circle amplification. The amplicon carried the aptameric sequences of ZnPPIX/TSPP porphyrin as photoreactive centers that rallied at periodical intervals of the persistent extension into a close-packed nanoflower, ZnPDFI/II. Both microscopies and electrophoresis proved the robust nesting of guests at their deployed gene loci, while multispectral comparisons among cofactor substituents pinpointed the pivotal roles of singlet seclusion and Zn2+-chelation for the sake of intensive ECL irradiation. The adversity-resilient hydrogel texture made lipoidal filmogens as porphyrinic ECL prerequisites to be of no need at all, thus not only simplifying assay flows but also inspiring an in situ labeling plan. Upon bioprocessing optimization, an enriched probe ZnPDFIII was further derived that interpolated the binding motif related to calprotectin as validated by molecular docking and affinity titration. With it being a strongly indicative marker of inflammatory bowel disease (IBD), a competitive ECL aptasensing strategy was contrived, managing a signal-on and sensitive detection in mild conditions with a subnanogram-per-milliliter limit of detection by 2 orders of magnitude lower than the standard method as well as a comparable accuracy in clinical stool sample testing. Distinct from those conventional chemophysical rebuilding routes, this de novo biosynthetic fusion demonstrated a promising alternative toward ECL-source bioengineering, which may intrigue vibrant explorations of other ECL-shedding fabrics and, accordingly, a new bioanalytic mode downstream.

Application and outlook of electrochemical technology in single-cell analysis

Cellular heterogeneity, especially in some important diseased cells like tumor cells, acts as an invisible driver for disease development like cancer progression in the tumor ecosystem, contributing to differences in the macroscopic and microscopic detection of disease lesions like tumors. Traditional analysis techniques choose group information masked by the mean as the analysis sample, making it difficult to achieve precise diagnosis and target treatment, on which could be shed light via the single-cell level determination/bioanalysis. Hence, in this article we have reviewed the special characteristic differences among various kinds of typical single-cell bioanalysis strategies and electrochemical techniques, and then focused on the recent advance and special bio-applications of electrochemiluminescence and micro-nano electrochemical sensing mediated in single-cell bioimaging & bioanalysis. Especially, we have summarized the relevant research exploration of the possibility to establish the in-situ single-cell electrochemical methods to detect cell heterogeneity through determination of specific biomolecules and bioimaging of some important biological processes. Eventually, this review has explored some important advances of electrochemical single-cell detection techniques for the real-time cellular bioimaging and diagnostics of some disease lesions like tumors. It raises the possibility to provide the specific in-situ platform to exploit the versatile, sensitive, and high-resolution electrochemical single-cell analysis for the promising biomedical applications like rapid tracing of some disease lesions or in vivo bioimaging for precise cancer theranostics.

T Cell Antigen Recognition and Discrimination by Electrochemiluminescence Imaging

Adoptive T lymphocyte (T cell) transfer and tumour-specific peptide vaccines are innovative cancer therapies. An accurate assessment of the specific reactivity of T cell receptors (TCRs) to tumour antigens is required because of the high heterogeneity of tumour cells and the immunosuppressive tumour microenvironment. In this study, we report a label-free electrochemiluminescence (ECL) imaging approach for recognising and discriminating between TCRs and tumour-specific antigens by imaging the immune synapses of T cells. Various T cell stimuli, including agonistic antibodies, auxiliary molecules, and tumour-specific antigens, were modified on the electrode's surface to allow for their interaction with T cells bearing different TCRs. The formation of immune synapses activated by specific stimuli produced a negative (shadow) ECL image, from which T cell antigen recognition and discrimination were evaluated by analysing the spreading area and the recognition intensity of T cells. This approach provides an easy way to assess TCR-antigen specificity and screen both of them for immunotherapies.

Ultrasensitive miRNA Detection Based on Magnetic Upconversion Nanoparticle Enhancement and CRISPR/Cas13a-Driven Signal Amplification

MicroRNAs (miRNAs), a class of small molecules with important regulatory functions, have been widely used in the field of biosensing as biomarkers for the early diagnosis of various diseases. Therefore, it is crucial to develop an miRNA detection platform with high sensitivity and specificity. Here, we have designed a CRISPR/Cas13-based enzymatic cyclic amplification system and regarded the magnetic upconversion nanoparticles (MUCNPs) as a biosensor of outputting the detection signal for the highly sensitive and high-fidelity detection of miRNAs. MUCNPs were composed of UCNPs (fluorescence donors) and Fe3O4@AuNPs (fluorescence acceptors) through double-stranded DNA hybrid coupling. The target miRNA acted as an activator, which could activate the trans-cleavage activity of Cas13a to the well-designed Trigger containing two uracil ribonucleotides (rU) in its loop and trigger a strand displacement reaction to generate a large amount of single-stranded DNA, resulting in the release of the UCNPs from MUCNPs. Benefiting from the high fidelity and high selectivity of CRISPR/Cas13a, the great effect of triggered enzymatic cycle amplification, and the high-intensity luminescent signal of MUCNPs, this method possessed miRNA detection capability with high sensitivity and specificity even in the complex environment with 10% fetal bovine serum (FBS) and a serum sample. Meanwhile, the detection limit could be as low as 83.2 fM. In addition, this method effectively reduced the effect of photobleaching and maintained high stability, which was expected to achieve efficient and sensitive miRNA detection.