End-grafted low-molecular-weight PNIPAM does not collapse above the LCST

Deswelling Mechanisms of PNIPAM Grafted in Nanochannels: A Molecular Dynamics Simulation Study

Porous thermosensitive hydrogels exhibit a more flexible strategy for freshwater capture compared to conventional hydrogels. This study employs molecular dynamics (MD) simulation to investigate the deswelling behavior of poly(N-isopropylacrylamide) (PNIPAM) grafted within the nanochannel, aiming to elucidate the deswelling elimination process at various temperatures. Notably, a distinct phase separation is observed at specific temperatures above the lower solution temperature (LCST). Furthermore, this study takes the effect of heat flux into account, wherein distinct heat fluxes lead to varying levels of phase separation between water and the polymer. Specifically, the number of hydrogen bonds, volume of polymer chains, and density distribution of water molecules are statistically analyzed to reveal the mechanism of phase separation in a thermosensitive hydrogel. These findings provide insight into the accelerated deswelling kinetics of the PNIPAM polymer chain, which has guiding significance for the field of water harvesting by the enhancement of the water release capacity in thermosensitive hydrogels.

Biocompatible Polymer for Self-Humidification

Lung supportive devices (LSDs) have been extensively utilized in treating patients diagnosed with various respiratory disorders. However, these devices can cause moisture depletion in the upper airway by interfering with the natural lubrication and air conditioning process. To remedy this, current technologies implement heated humidification processes, which are bulky, costly, and nonfriendly. However, it has been demonstrated that in a breath cycle, the amount of water vapor in the exhaled air is of a similar quantity to the amount needed to humidify the inhaled air. This research proposes to trap the moisture from exhaled air and reuse it during inhalation by developing a state-of-the-art hydrophilic/hydrophobic polymer tuned to deliver this purpose. Using the atom transfer radical polymerization (ATRP) method, a substrate was successfully created by incorporating poly (N-isopropyl acrylamide) (PNIPAM) onto cotton. The fabricated material exhibited a water vapor release rate of 24.2 ± 1.054%/min at 32 °C, indicating its ability to humidify the inhaled air effectively. These findings highlight the potential of the developed material as a promising solution for applications requiring rapid moisture recovery.

Stimulus-Responsive Transport Properties of Nanocolloidal Hydrogels

Applications of polymer hydrogels in separation technologies, environmental remediation, and drug delivery require control of hydrogel transport properties that are largely governed by the pore dimensions. Stimulus-responsive change in pore size offers the capability to change gel's transport properties "on demand". Here, we report a nanocolloidal hydrogel that exhibits temperature-controlled increase in pore size and, as a result, enhanced transport of encapsulated species from the gel. The hydrogel was formed by the covalent cross-linking of aldehyde-modified cellulose nanocrystals and chitosan carrying end-grafted poly(N-isopropylacrylamide) (pNIPAm) molecules. Owing to the temperature-mediated coil-to-globule transition of pNIPAm grafts, they acted as a temperature-responsive "gate" in the hydrogel. At elevated temperature, the size of the pores showed up to a 4-fold increase, with no significant changes in volume, in contrast with conventional pNIPAm-derived gels exhibiting a reduction in both pore size and volume in similar conditions. Temperature-mediated transport properties of the gel were explored by studying diffusion of nanoparticles with different dimensions from the gel, leading to the established correlation between the kinetics of diffusion-governed nanoparticle release and the ratio nanoparticle dimensions-to-pore size. The proposed approach to stimulus-responsive control of hydrogel transport properties has many applications, including their use in nanomedicine and tissue engineering.

On the foundation of thermal "Switching": The culture substrate governs the phase transition mechanism of thermoresponsive brushes and their performance in cell sheet fabrication

Thermally "switchable" poly(glycidyl ether) (PGE) brushes constitute effective coatings for the temperature-triggered harvest of confluent cell sheets. Based on a simple "grafting-to" approach, such coatings can be tethered to various applied plastic culture substrate materials. Herein, we elucidate the self-assembly of PGE brushes with tunable grafting densities up to 0.12 and 0.22 chains nm^-2 on polystyrene (PS) and tissue culture PS (TCPS), respectively. In terms of temperature-dependent wettability and protein adsorption, we found that brushes exhibit distinct grafting density-dependent properties which correlate with their cell sheet fabrication performance. In addition, temperature-ramped quartz-crystal microbalance with dissipation (QCM-D) measurements revealed marked substrate-specific PGE phase transitions which allowed us to deduce comprehensive switching mechanisms. Thus, we demonstrate that brushes tethered to hydrophilic TCPS (contact angle (CA) ∼ 60°) undergo a "cushioned" transition comprising a non-switchable, hydrated basal layer as well as a switchable top layer which regulates cell sheet detachment. In contrast, PGE brushes tethered to PS undergo a "grounded" transition which is substantially influenced by the dehydrating effect of the less hydrophilic PS substrate (CA ∼ 90°). These divergent phase transition mechanisms give rise to a broad scope in cell sheet fabrication performance, yielding staggered detachment times within a 30 min to 3 h range. Hence, we emphasize the importance of a detailed knowledge on the effect of applied culture substrates on the thermal switchability and phase transition characteristics of thermoresponsive brush coatings to accomplish an optimized design for functional cell culture dishes. STATEMENT OF SIGNIFICANCE: As the first comparative study of its kind, we elucidate the substrate-dependent thermal switchability of thermoresponsive brush coatings and evaluate their grafting density-dependent phase transition mechanism and its effect on cell sheet fabrication performance.

Stabilization and Kinetics of an Adsorbed Protein Depends on the Poly(N-isopropylacrylamide) Grafting Density

The solubility transition at the lower critical solution temperature (LCST, 32 °C) of poly(N-isopropylacrylamide) (PNIPAM) is widely used as a thermal switch to rapidly and reversibly capture and release proteins and cells. It is generally assumed that proteins adsorbed to PNIPAM above the LCST are unaffected by polymer interactions. Here we show that the folding stability of the enzyme phosphoglycerate kinase (PGK) is increased by interactions with end-grafted PNIPAM films above the LCST. We systematically compare two protein mutants with different stabilities. The stabilization mirrors the degree of protein adsorption under grafting conditions studied previously. Maximum stabilization occurs when proteins adsorb to low density, collapsed polymer "mushrooms". In the denser polymer "brush" regime, protein stabilization decreases back to a value indistinguishable from the bulk solution, consistent with low protein adsorption on dense, collapsed brushes. The temperature-dependent kinetics measured by Fast Relaxation Imaging reveals that PNIPAM does not affect the overall folding/unfolding mechanism. Based on the different stabilizations of two mutants and the relaxation kinetics, we hypothesize that the polymer acts mainly by increasing the conformational entropy of the folded protein by interacting with the protein surface and less by crowding the unfolded state of PGK.

Constrained thermoresponsive polymers - new insights into fundamentals and applications

In the last decades, numerous stimuli-responsive polymers have been developed and investigated regarding their switching properties. In particular, thermoresponsive polymers, which form a miscibility gap with the ambient solvent with a lower or upper critical demixing point depending on the temperature, have been intensively studied in solution. For the application of such polymers in novel sensors, drug delivery systems or as multifunctional coatings, they typically have to be transferred into specific arrangements, such as micelles, polymer films or grafted nanoparticles. However, it turns out that the thermodynamic concept for the phase transition of free polymer chains fails, when thermoresponsive polymers are assembled into such sterically confined architectures. Whereas many published studies focus on synthetic aspects as well as individual applications of thermoresponsive polymers, the underlying structure-property relationships governing the thermoresponse of sterically constrained assemblies, are still poorly understood. Furthermore, the clear majority of publications deals with polymers that exhibit a lower critical solution temperature (LCST) behavior, with PNIPAAM as their main representative. In contrast, for polymer arrangements with an upper critical solution temperature (UCST), there is only limited knowledge about preparation, application and precise physical understanding of the phase transition. This review article provides an overview about the current knowledge of thermoresponsive polymers with limited mobility focusing on UCST behavior and the possibilities for influencing their thermoresponsive switching characteristics. It comprises star polymers, micelles as well as polymer chains grafted to flat substrates and particulate inorganic surfaces. The elaboration of the physicochemical interplay between the architecture of the polymer assembly and the resulting thermoresponsive switching behavior will be in the foreground of this consideration.

Thermoresponsive Gigaporous Microspheres Facilitate the Efficient Refolding of Recombinant Nitrilase Inclusion Bodies

In order to assist the refolding of recombinant nitrilase inclusion bodies, a series of thermoresponsive media were prepared by grafting poly(N-isopropylacrylamide-co-butyl-methacrylate) [P(NIPAM-co-BMA)] brushes onto PS microspheres with various particles and pore sizes via an atom transfer radical polymerization (ATRP) method. The effects of particle sizes, pore sizes, and brush grafting amounts of thermoresponsive microspheres on nitrilase refolding were investigated preliminarily. The results showed that the PS-P(NIPAM-co-BMA) microspheres with the medium particle size (74 μm), gigapore size (320 nm), and high grafting amount (35.6 mg/m²) were the most effective candidates. The final nitrilase activity yield could be up to 84.5% with a high initial protein concentration (1 mg/mL) at 30 °C, which was 52.5% higher than that of a simple dilution refolding method at the initial protein concentration (0.1 mg/mL). After the refolding process, the PS-P(NIPAM-co-BMA) microspheres can be easily separated by self-precipitation, and the activity yield of nitrilase still reached 74.5% after being reused for five batches. These results indicated that the thermoresponsive gigaporous medium was an ideal alternative as an artificial chaperone.

Lubrication and drug release behaviors of mesoporous silica nanoparticles grafted with sulfobetaine-based zwitterionic polymer

Osteoarthritis, which is characterized by irreversible destruction of articular cartilage and severe inflammation of joint capsule, may be effectively treated via the synergistic therapy of lubrication restoration and local drug intervention. In this study, zwitterionic polymer-grafted mesoporous silica nanoparticles (MSNs@pSBMA) with the property of enhanced lubrication and sustained drug release were successfully synthesized via photopolymerization of 3-[dimethyl-[2-(2-methylprop-2-enoyloxy) ethyl] azaniumyl] propane-1-sulfonate polymer (pSBMA) on the surface of MSNs. The tribiological test showed that the lubrication performance of MSNs@pSBMA was remarkably improved, with a reduction of 80% in friction coefficient compared with MSNs. It was attributed to hydration lubrication mechanism by which a tenacious hydration layer was formed surrounding the N⁺(CH₂)₂(CH₃)₂ and SO₃^- headgroups in the pSBMA polyelectrolyte polymer. Additionally, the surface morphology analysis of the tribopairs demonstrated that MSNs@pSBMA were endowed with excellent anti-wear performance. Importantly, the drug release test illustrated that, compared with MSNs, MSNs@pSBMA achieved good sustained drug release behavior. In summary, the MSNs@pSBMA nanoparticles developed herein, as an injectable lubricant with enhanced lubrication and drug delivery, may represent a promising approach for the treatment of osteoarthritis.

Responsive Adsorption of N-Isopropylacrylamide Based Copolymers on Polymer Brushes

We investigate the adsorption of pH- or temperature-responsive polymer systems by ellipsometry and neutron reflectivity. To this end, temperature-responsive poly (N-isopropylacrylamide) (PNIPAM) brushes and pH-responsive poly (acrylic acid) (PAA) brushes have been prepared using the "grafting onto" method to investigate the adsorption process of polymers and its reversibility under controlled environment. To that purpose, macromolecular brushes were designed with various chain lengths and a wide range of grafting density. Below the transition temperature (LCST), the characterization of PNIPAM brushes by neutron reflectivity shows that the swelling behavior of brushes is in good agreement with the scaling models before they collapse above the LCST. The reversible adsorption on PNIPAM brushes was carried out with linear copolymers of N-isopropylacrylamide and acrylic acid, P(NIPAM-co-AA). While these copolymers remain fully soluble in water over the whole range of temperature investigated, a quantitative adsorption driven by solvophobic interactions was shown to proceed only above the LCST of the brush and to be totally reversible upon cooling. Similarly, the pH-responsive adsorption driven by electrostatic interactions on PAA brushes was studied with copolymers of NIPAM and N,N-dimethylaminopropylmethacrylamide, P(NIPAM-co-MADAP). In this case, the adsorption of weak polycations was shown to increase with the ionization of the PAA brush with interactions mainly located in the upper part of the brush at pH 7 and more deeply adsorbed within the brush at pH 9.

3D printed nanocomposites using polymer grafted graphene oxide prepared by multicomponent Passerini reaction

The surface of commercial graphene oxide was modified with polymers using Passerini reaction, which enhances the compatibility between nanoparticles and 3D printing resin.

Adhesion and Particle Removal from Surface-Tethered Poly(N-Isopropylacrylamide) Coatings Using Hydrodynamic Shear Forces

Thermally responsive coatings of poly(N-isopropylacrylamide), or poly(NIPAAm), have a volume phase transition temperature (VPTT) near 32 °C. Below this temperature, the coating imbibes water and swells. Above this temperature, the coating rejects water and collapses. Herein, a spinning disk method is used to determine the hydrodynamic shear stress necessary to remove 10 μm polystyrene (PS) microspheres capped with either carboxylic acid (COOH) functionality or immunoglobulin (IgG) proteins from the coatings as a function of coating thickness and temperature. In the case of the PS-COOH, the hydrodynamic shear stress necessary to remove the microspheres was consistently larger below the VPTT than above the VPTT of the poly(NIPAAm) coating. In the case of PS-IgG, the trend was reversed, in which the hydrodynamic shear stress necessary to remove the microspheres was consistently smaller below the VPTT than above the VPTT. Simple scaling relationships were developed to explain the findings within the Johnson-Kendall-Roberts (JKR) model of contact mechanics, which illustrates the delicate interplay between the pull-off force and contact radius (as determined by the coating shear modulus) in governing particle removal from soft surfaces with hydrodynamic forces.

Poly(N-isopropylacrylamide) Response to Salt Concentration and Anion Identity: A Brush-on-Brush Study

The stability of poly(N-isopropylacrylamide) (PNIPAM) brush-modified colloidal silica particles was compared to asymmetric and symmetric PNIPAM brush direct force measurements in the presence of 1, 10, and 500 mM aqueous salt solution of KCl, KNO₃, and KSCN between 10 and 45 °C. Dynamic light scattering measurements highlighted subtle variations in the salt-mediated thermoresponse, while atomic force microscopy (AFM) force curves between a bare silica or PNIPAM brush-modified colloid probe and a planar PNIPAM brush elucidated differences in brush interactions. The AFM force curves in the presence of KCl primarily revealed steric interactions between the surfaces, while KNO₃ and KSCN solutions exhibited electrosteric interactions on approach as a function of the chaotropic nature of the ion and the solution concentration. The symmetric PNIPAM brush interaction highlighted significant variations between KCl and KSCN at 1 and 500 mM concentrations, while the approach and retraction force curves were relatively similar at 10 mM concentration. The combination of these techniques enabled the stability of PNIPAM brush-modified colloidal dispersions in the presence of electrolyte to be better understood with specific ion binding and the solution Debye length playing a significant role.

Block copolymers as bile salt sequestrants: intriguing structures formed in a mixture of an oppositely charged amphiphilic block copolymer and bile salt

To study the formation and characterize the structure of mixed complexes of oppositely charged block copolymers and surfactants are of great significance for practical applications, e.g., in drug carrier formulations that are based on electrostatically assisted assembly. In this context, biocompatible block copolymers and biosurfactants (like bile salts) are particularly interesting. In this work, we report on the co-assembly in dilute aqueous solution between a cationic poly(N-isopropyl acryl amide) (PNIPAM) diblock copolymer and the oppositely charged bile salt surfactant sodium deoxycholate at ambient temperature. The cryogenic transmission electron microscopy (cryo-TEM) experiments revealed the co-existence of two types of co-assembled complexes of radically different morphology and inner structure. They are formed mainly as a result of the electrostatic attraction between the positively charged copolymer blocks and bile salt anions and highlight the potential of using linear amphiphilic block copolymers as bile salt sequestrants in the treatment of bile acid malabsorption and hypercholesterolemia. The first complex of globular morphology has a coacervate core of deoxycholate anions and charged copolymer blocks surrounded by a PNIPAM corona. The second complex has an intriguing tape-like supramolecular morphology of several micrometer in length that is striped in the direction of the long axis. A model is presented in which the stretched cationic blocks of several block copolymers interact electrostatically with the bile salt molecules that are associated to form a zipper-like structure. The tape is covered on both sides by the PNIPAM chains that stabilize the overall complex in solution. In addition to cryo-TEM, the mixed system was investigated in a range of molar charge fractions at a constant copolymer concentration by static light scattering, small angle X-ray scattering, and electrophoretic mobility measurements.

Highly-branched poly(N-isopropyl acrylamide) functionalised with pendant Nile red and chain end vancomycin for the detection of Gram-positive bacteria

This study shows how highly branched poly(N-isopropyl acrylamide) (HB-PNIPAM) with a chain pendant solvatochromic dye (Nile red) could provide a fluorescence signal, as end groups bind to bacteria and chain segments become desolvated, indicating the presence of bacteria. Vancomycin was attached to chain ends of HB-PNIPAM or as pendant groups on linear polymers each containing Nile red. Location of the dye was varied between placement in the core of the branched polymer coil or the outer domains. Both calorimetric and fluorescence data showed that branched polymers responded to binding of both the peptide target (D-Ala-D-Aa) and bacteria in a different manner than analogous linear polymers; binding and response was more extensive in the branched variant. The fluorescence data showed that only segments located in the outer domains of branched polymers responded to binding of Gram-positive bacteria with little response when linear analogous polymer or branched polymer with the dye in the inner core was exposed to Staphylococcus aureus.

Temperature-dependent structure and dynamics of highly-branched poly(N-isopropylacrylamide) in aqueous solution

Small-angle neutron scattering (SANS) and neutron spin-echo (NSE) have been used to investigate the temperature-dependent solution behaviour of highly-branched poly(N-isopropylacrylamide) (HB-PNIPAM). SANS experiments have shown that water is a good solvent for both HB-PNIPAM and a linear PNIPAM control at low temperatures where the small angle scattering is described by a single correlation length model. Increasing the temperature leads to a gradual collapse of HB-PNIPAM until above the lower critical solution temperature (LCST), at which point aggregation occurs, forming disperse spherical particles of up to 60 nm in diameter, independent of the degree of branching. However, SANS from linear PNIPAM above the LCST is described by a model that combines particulate structure and a contribution from solvated chains. NSE was used to study the internal and translational solution dynamics of HB-PNIPAM chains below the LCST. Internal HB-PNIPAM dynamics is described well by the Rouse model for non-entangled chains.

Temperature- and/or pH-Responsive Surfaces with Controllable Wettability: From Parahydrophobicity to Superhydrophilicity

Multifunctional surfaces with reversible wetting characteristics are fabricated utilizing end-anchored polymer chains on hierarchically roughened surfaces. Temperature- and/or pH-responsive surfaces are developed that exhibit reversible and controllable wettability, from the "parahydrophobic" behavior of natural plant leaves all the way to superhydrophilic properties in response to the external stimuli. For this purpose, dual scale micro/nanoroughened surfaces were prepared by laser irradiation of inorganic surfaces (Si wafers) utilizing ultrafast (femtosecond) laser pulses under a reactive gas atmosphere. End-functionalized polymer chains were anchored onto those surfaces utilizing the "grafting to" method; poly(N-isopropylacrylamide), PNIPAM, and poly(2-vinylpyridine), P2VP, were used for the formation of monofunctional as well as mixed brushes. The surfaces exhibit "parahydrophobic" behavior in the hydrophobic state (high temperature and/or high pH), with high static contact angles (∼120°) and high water adhesion (∼30° contact angle hysteresis), whereas they show superhydrophilic behavior in the hydrophilic state (low temperature and/or low pH). The surfaces were tested for their wettability under repetitive cycles and found to be stable and reproducible.

Thermoresponsive poly(glycidyl ether) brushes on gold: Surface engineering parameters and their implication for cell sheet fabrication

Thermoresponsive polymer coatings, optimized for cell adhesion and thermally-triggered cell detachment, allow the fabrication of confluent cell sheets with intact extracellular matrix. However, rational design guidelines for such coatings are rare, since temperature-triggered cell adhesion and detachment from thermoresponsive surfaces are mechanistically not well understood. Herein, we investigated the impact of molecular weight (2, 9, 24kDa), grafting density (0.04-1.4 chains nm^-2), morphology, and roughness of well-characterized thermoresponsive poly(glycidyl ether) brushes on the cell response at 37 and 20°C. NIH 3T3 mouse fibroblasts served as a model cell line for adhesion, proliferation, and cell sheet detachment. The cell response was correlated with serum protein adsorption from cell culture medium containing 10% fetal bovine serum. Intact cell sheets could be harvested from all the studied poly(glycidyl ether) coated surfaces, irrespective of the molecular weight, provided that the morphology of the coating was homogenous and the surface was fully shielded by the hydrated brush. The degree of chain overlap was estimated by the ratio of twice the polymer's Flory radius in a theta solvent to its interchain distance, which should be located in the strongly overlapping brush regime (2 R_f/l>1.4). In contrast, dense PNIPAM (2.5kDa) control monolayers did not induce protein adsorption from cell culture medium at 37°C and, as a result, did not allow a significant cell adhesion. These structural design parameters of functional poly(glycidyl ether) coatings on gold will contribute to future engineering of these thermoresponsive coatings on more common, cell culture relevant substrates.

STATEMENT OF SIGNIFICANCE

Cell sheet engineering as a scaffold-free approach towards tissue engineering resembles a milestone in regenerative medicine. The fabrication of confluent cell sheets maintains the extracellular matrix of cells which serves as the physiological cell scaffold. Thermoresponsive poly(glycidyl ether)s are highly cell-compatible and brushes thereof promote cell adhesion and growth without modification with additional cell adhesive ligands. Thus, a direct correlation of temperature-dependent serum protein adsorption and cell response with surface design parameters such as grafting density and molecular weight became accessible. Hence, surface engineering parameters of well-defined poly(glycidyl ether) monolayers for reproducible cell sheet fabrication have been identified. These design guidelines may also prove beneficial in the development of other brush-like thermoresponsive coatings for cell sheet engineering.

Preparation of a surface-grafted imprinted ceramic membrane for selective separation of molybdate anion from water solutions

A surface-grafted imprinted ceramic membrane (IIP-PVI/CM) for recognizing molybdate (Mo(VI)) anion was prepared by surface-initiated graft-polymerization. Firstly, raw alumina ceramic membrane (CM) was deposited with SiO₂ active layer by situ hydrolysis deposition method. Subsequently, γ-methacryloxy propyl trimethoxyl silane (MPS) was used as a coupling agent to introduce double bonds onto the SiO₂ layer (MPS-CM). Then, 1-vinylimidazole (VI) was employed as a functional monomer to graft-polymerization onto the MPS-CM (PVI-CM). During the graft-polymerization, the influence factors of grafting degree of PVI were investigated in detail. Under optimum conditions (monomer concentration 20wt%, temperature 70°C, initiator amount 1.1wt% and reaction time 8h), the grafting degree of 20.39g/100g was obtained. Further, Mo(VI) anion was used as a template to imprint in the PVI-CM by employing 1,6-dibromohexane as a cross-linking agent, and then Mo(VI) was removed, obtaining the IIP-PVI/CM with many imprinted cavities for Mo(VI). Thereafter, static adsorption and dynamic separation properties of IIP-PVI/CM for Mo(VI) were studied. Results indicate that IIP-PVI/CM shows a specific selectivity for Mo(VI) with the adsorption capacity of 0.69mmol/100g, and the selectivity coefficient of IIP-PVI/CM is 7.48 for molybdate to tungstate anions. During the dynamic separation, IIP-PVI/CM has also good selectivity for separation of Mo(VI) and W(VI) anions.

Nanostructured Thermal Responsive Materials Synthesized by Soft Templating

We capitalized herein the inherent tortuosity of bicontinuous microemulsion to conceive nanostructured drug-delivery devices. First, we show that it is possible to synthesize bicontinuous materials with continuous hydrophilic domains of the poly(N-isopropylacrylamide) (PNIPAM) network entangled with continuous hydrophobic polymer domains, with dual-phase continuity being imposed by the bicontinuous microemulsions used as a soft template. Particular attention is paid to the microemulsion formulations using a surfmer to preserve the one-to-one replication of the bicontinuous nanostructure after polymerization. These materials keep a volume phase transition with temperature that allows considering them as drug carriers for controlled release. PNIPAM, which plays the role of the active ingredient reservoir, is confined in the bicontinuous structure. As expected, the PNIPAM enclosure limits the surface area in contact with the releasing aqueous solution and thus slows down the desorption of aspirin, which is used as a model drug. The hydrophobic polymers play the role of in situ-created transport barriers without hindering it as all the loaded aspirin in this bicontinuous structure still remains available.

On the formation of inclusion complexes at the solid/liquid interface of anchored temperature-responsive PNIPAAM diblock copolymers with γ-cyclodextrin

The thermal responsive behavior of adsorbed layers of diblock copolymers of poly(N-isopropylacrylamide) (PNIPAAM) and poly((3-acrylamidopropyl)trimethylammonium chloride) (PAMPTMA(+)) with γ-cyclodextrin (γ-CD) at the solid/liquid interface has been investigated using three in situ techniques: null ellipsometry, quartz-crystal microbalance with dissipation monitoring, and neutron reflectometry. The measurements provided information about the adsorbed amounts, the layer thickness, hydration and viscoelastic properties, and the interfacial structure and composition. The copolymers adsorb to silica with the cationic PAMPTMA(+) blocks sitting as anchors in a flat conformation and the PNIPAAM chains extending into the solution. The copolymer system alone exhibits reversible collapse above the lower critical solution temperature of PNIPAAM. The addition of γ-CD to pre-adsorbed copolymer layers results in a highly extended conformation as well as some loss of copolymer from the surface, which we discuss in terms of the formation of surface-invoked lateral steric repulsion of formed inclusion complexes.

Synergistic Effects of Bound Micelles and Temperature on the Flexibility of Thermoresponsive Polymer Brushes

The persistence length is a key parameter for the quantitative interpretation of the flexibility of polymers. We have studied complexes composed of a spherical poly(N-isopropylacrylamide) (PNIPAM) brush and a sodium dodecyl sulfate micelle in an effort to characterize the flexibility of tethered PNIPAM below the lower critical solution temperature T_LCST. An analytical mean-field model is used to describe the persistence length L_p in a broad range of ψ, the number of bound micelles per chain. The persistence length of micelle-constrained PNIPAM is quantitatively correlated with the thermal energy k_BT, electrostatic repulsion f_C, and effective excluded-volume parameter ν_eff. The persistence length per ψ, which depends on T and f_C, is found to scale with a synergistic effect f_C/(ψk_BT). The results reveal that the bound-micelle charges affecting the persistence length are analogous to the fixed charges of polyelectrolytes, though the bound micelles are separated by a large number of neutral monomers. The extension ⟨L⟩ of micelle-constrained PNIPAM decreases as ⟨L⟩ ∼ f_C^-β_F with f_C, where β_F ≈ 0.58-0.8 depending on ψ, but as the universal power law ⟨L⟩ ∼ (f_C/k_BT)^-0.6 with the synergistic effect f_C/(k_BT), irrespective of ψ. In spite of the intricate interplay among the multiple components in the system, the extension scales as a function of ν_eff as ⟨L⟩ ∼ (ν_eff/ψL_p)^-β_V, where β_V ≈ 0.35 for the significant monomer interaction and β_V ≈ 0.2 for the weak or negligible monomer interaction.

Triggered Release from Thermoresponsive Polymersomes with Superparamagnetic Membranes

Magnetic polymersomes were prepared by self-assembly of the amphiphilic block copolymer poly(isoprene-b-N-isopropylacrylamide) with monodisperse hydrophobic superparamagnetic iron oxide nanoparticles (SPION). The specifically designed thermoresponsive block copolymer allowed for efficient incorporation of the hydrophobic nanoparticles in the membrane core and encapsulation of the water soluble dye calcein in the lumen of the vesicles. Magnetic heating of the embedded SPIONs led to increased bilayer permeability through dehydration of the thermoresponsive PNIPAM block. The entrapped calcein could therefore be released in controlled doses solely through exposure to pulses of an alternating magnetic field. This hybrid SPION-polymersome system demonstrates a possible direction for release applications that merges rational polymersome design with addressed external magnetic field-triggered release through embedded nanomaterials.

Sorption of Water and Initial Stages of Swelling of Thin PNIPAM Films Using in Situ GISAXS Microfluidics

The sorption of low-molecular penetrants by thin polymer films, as well as structural changes provoked therein, is of high relevance for many fields of application. Complex permeation, diffusion, swelling, and dissolution processes are often induced within films by solvents or gases. Here, we use a novel in situ microfluidics-grazing incidence small-angle X-ray scattering (GISAXS) setup to examine changes in film thickness and in the surface structure of a thin polymer film that sorbs a good solvent. Thus, this technique is highly complementary to the established techniques on the field of diffusion in polymers. The initial stages of water uptake and swelling are resolved for a 50 nm thin, hydrophilic poly(N-isopropylacrylamide) (PNIPAM) film, before its dissolution sets in. The initial stages of swelling are tentatively described by anomalous swelling induced by a time- and space-dependent diffusion coefficient.

Poly(N-isopropylacrylamide)-Based Mixed Brushes: A Computer Simulation Study

Temperature-sensitive poly(N-isopropylacrylamide) (PNIPAM) polymer brushes of fixed molecular weight and grafting density are modeled in the framework of a coarse-grained model with soft, nonbonded interactions and an implicit solvent. This model has been developed to address experimentally relevant, large invariant degrees of polymerization, and nonbonded interactions are expressed via a third-order (virial) expansion of the equation of state. The choice of interaction parameters is intended to mimic the swelling behavior of PNIPAM in water as the temperature increases toward the lower critical solution temperature (T(LCST)). Results of molecular dynamics simulations for one component brushes are compared to experimental data. Mixed brushes incorporating small and large amounts of grafted poly(ethylene glycol) polymers are then considered. The effects of mixing polymer components on the response of the mixed brushes to temperature changes are monitored, and the results are compared to experimental data. In the end, two design principles for biomolecule triggering using temperature-sensitive mixed polymer brushes with functional and switchable end-groups are proposed and studied. This work is in favor of establishing qualitative rules for the design, optimization, and comprehension of binary polymer brushes for bioengineering purposes.

Temperature-dependent drug release from DPPC:C12H25-PNIPAM-COOH liposomes: control of the drug loading/release by modulation of the nanocarriers' components

Novel polymer-modified thermosensitive liposomes were developed for the delivery of indomethacin in order to control its release profile. When attached to 1,2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC) liposomes, the end functionalized C12H25-poly(N-isopropylacrylamide)-COOH (C12H25-PNIPAM-COOH) polymer was membrane-disruptive in a temperature-dependent manner. The interest for this polymer is driven by its famous lower critical solution temperature (LCST) behavior, where heating an aqueous solution of PNIPAM above 32°C induces nanophase separation and polymer chain aggregation. The physicochemical/structural behavior of these polymer-modified thermosensitive liposomes was found to depend on the PNIPAM:lipid molar ratio and the composition of the polymeric guest. The incorporation of PNIPAM has caused alterations in the thermotropic behavior of DPPC liposomes, as the differential scanning calorimetry (DSC) experiments revealed. The drug loading and the release were found to be strongly dependent on the thermotropic characteristics of the PNIPAM grafted DPPC liposomes. Namely, the in vitro release is immediate at 37°C (>LCST) ("burst" effect), while the prepared mixed nanocarriers did not release the encapsulated bioactive substance at <32°C (<LCST). Thus, the thermosensitivity and the drug loading/release properties of the prepared formulations can be modulated by varying the ratio of DPPC/PNIPAM components, as well as the molecular characteristics of the polymeric guest.

Novel conjugated Ag@PNIPAM nanocomposites for an effective antibacterial wound dressing

It is well known that nanosilver or silver ions could act as an effective antibacterial agent without the development of bacterial resistance but long term exposure may induce in vivo toxicity.

Effects of terminal group and chain length on temperature-responsive chromatography utilizing poly(N-isopropylacrylamide) synthesized via RAFT polymerization

Even using the same homo poly(N-isopropylacrylamide) immobilized silica beads as stationary phases, terminal functional group and chain length significantly affected temperature-dependent elution behavior of steroids.

phase instability and molecular kinetics provoked by repeated crossing of the demixing transition of PNIPAM solutions

The demixing process of aqueous poly(N-isopropylacrylamide) (PNIPAM) solutions can occur either via a nucleation and growth process or via spinodal decomposition. The ensuing self-assembly, leading to heterogeneous morphologies within the PNIPAM solution, is codetermined by kinetic processes caused by molecular transport. By subjecting PNIPAM solutions to cyclic changes in temperature leading to repeated crossing of the demixing transition, we are able to assess the importance of kinetics as well as of overheating and supercooling of the phase transition within the metastable range delimited by the binodal and spinodal lines. First indications about the location of these stability limits for the low- and high-temperature phases, separated by about 1.6 K, could be gained by detailed kinetic studies of the refractive index. These investigations are made possible due to the novel technique of temperature-modulated optical refractometry.

Collapse from the top: brushes of poly(N-isopropylacrylamide) in co-nonsolvent mixtures

Using a combination of ellipsometry and friction force microscopy, we study the reversible swelling, collapse and variation in friction properties of covalently bound poly(N-isopropylacrylamide) (PNIPAM) layers on silicon with different grafting densities in response to exposure to good solvents and co-nonsolvent mixtures. Changes in the thickness and segment density distribution of grafted films are investigated by in situ ellipsometry. Based on quantitative modelling of the ellipsometry spectra, we postulate a structural model, which assumes that collapse takes place in the contacting layer between the brush and the co-nonsolvent and the top-collapsed brushes remain hydrated in the film interior. Using the structural model derived from ellipsometry spectra, we analyse the AFM based friction force microscopy data, which were obtained by silica colloidal probes. Results show a large increase of the friction coefficient of PNIPAM grafts when the grafts swollen by water are brought in contact with co-nonsolvents. For instance, the value of the friction coefficient for a medium density brush in water is four times lower than the value observed in a water-methanol (50% v/v) mixture. This increase of friction is accompanied by an increase in adherence between the PNIPAM chains and the silica colloidal probes, and is a result of chain collapse in the graft when contacted by a co-nonsolvent mixture in agreement with the model postulated on the basis of ellipsometric characterisation. The kinetic behaviour of the collapse is assessed by measuring the temporal variation of friction in situ as a function of elapsed time following contact with the co-nonsolvent as a function of graft density. In conclusion, the effect of co-nonsolvency influenced both the thickness of the PNIPAM brushes and the tribological behavior of the brush surfaces.