Confinement-Induced Deviation of Chain Mobility and Glass Transition Temperature for Polystyrene/Au Nanoparticles

Temperature-Responsive Polymer Brush Coatings for Advanced Biomedical Applications

Modern biomedical technologies predict the application of materials and devices that not only can comply effectively with specific requirements, but also enable remote control of their functions. One of the most prospective materials for these advanced biomedical applications are materials based on temperature-responsive polymer brush coatings (TRPBCs). In this review, methods for the fabrication and characterization of TRPBCs are summarized, and possibilities for their application, as well as the advantages and disadvantages of the TRPBCs, are presented in detail. Special attention is paid to the mechanisms of thermo-responsibility of the TRPBCs. Applications of TRPBCs for temperature-switchable bacteria killing, temperature-controlled protein adsorption, cell culture, and temperature-controlled adhesion/detachment of cells and tissues are considered. The specific criteria required for the desired biomedical applications of TRPBCs are presented and discussed.

Optical Imaging of the Molecular Mobility of Single Polystyrene Nanospheres

An ultrathin surface layer with extraordinary molecular mobility has been discovered and intensively investigated on thin-film polymer materials for decades. However, because of the lack of suitable characterization techniques, it remains largely unexplored whether such a surface mobile layer also exists on individual polymeric nanospheres. Here, we propose a thermal-optical imaging technique to determine the glass transition (T_g) and rubber-fluid transition (T_f) temperatures of single isolated polystyrene nanospheres (PSNS) in a high-throughput and nonintrusive manner for the first time. Two distinct steps, corresponding to the glass transition and rubber-fluid transition, respectively, were clearly observed in the optical trace of single PSNS during temperature ramping. Because the transition temperature and size of the same individuals were both determined, single nanoparticle measurements revealed the reduced apparent T_f and increased T_g of single PSNS on the gold substrate with a decreasing radius from 130 to 70 nm. Further experiments revealed that the substrate effect played an important role in the increased T_g. More importantly, a gradual decrease in the optical signal was detected prior to the glass transition, which was consistent with a surface layer with enhanced molecular mobility. Quantitative analysis further revealed the thickness of this layer to be ∼8 nm. This work not only uncovered the existence and thickness of a surface mobile layer in single isolated nanospheres but also demonstrated a general bottom-up strategy to investigate the structure-property relationship of polymeric nanomaterials by correlating the thermal property (T_g and T_f) and structural features (size) at single nanoparticle level.

Inorganic reinforced poly(ionic liquid) microcapsules: confined cooling-assisted phase separation self-assembly and enhanced electro-responsive property

We report a simple preparation of inorganic reinforced poly(ionic liquid) (PIL) microcapsules by combining dispersion polymerization and confined cooling-assisted phase separation self-assembly. Silane coupling agent-modified PIL microbeads were first prepared by dispersion polymerization. Then, the microbeads were dissolved in a mixed solvent composed of good solvent and non-solvent to form hollow SiO_x microcapsules at a relatively high temperature. Finally, the solution was cooled to induce the nucleation and growth of dissolved PIL chains on the inner and outer surface of hollow SiO_x microcapsules to form inorganic reinforced microcapsules with asymmetric PIL/SiO_x /PIL sandwich-like shell. The morphology of microcapsules can be controlled by adjusting PIL concentration and cooling rate. The inorganic reinforced microcapsules show enhanced suspended stability and electro-responsive characteristic when used as the dispersed phase of smart suspensions. This article is protected by copyright. All rights reserved.

Glass transition temperature of single-chain polystyrene particles end-grafted to oxide-coated silicon

A method based on the PeakForce QNM atomic force microscopic (AFM) adhesion measurement is employed to investigate the glassy dynamics of polystyrene (PS) single-chain particles end-grafted to SiO₂-Si substrates with different diameters, D₀, of 3.4 nm-8.8 nm and molar masses, M_n, of 8-123 kg/mol. As temperature was increased, the adhesion force, F_ad, experienced by the AFM tip on pulling off the single chains after loading demonstrated a stepwise increase at an elevated temperature, which we identified to be T_g based on previous works. Our result shows that T_g of our grafted single chains increases with M_n in a manner consistent with the Fox-Flory equation, but the coefficient quantifying the M_n dependence of T_g is only (36 ± 6)% the value of bulk PS. In addition, the value of T_g in the M_n → ∞ limit is about 25 °C below the bulk T_g but more than 15 °C above that of (untethered) PS nanoparticles with D₀ ≈ 100 nm suspended in a solution. Our findings are consistent with T_g of our single chains being dominated by simultaneous effects of the interfaces, which depress T_g, and end-grafting, which enhances T_g. The latter is believed to exert its influence on the glass transition dynamics by a mechanism reliant on chain connectivity and does not vary with chain length.

Deterioration in the Physico-Mechanical and Thermal Properties of Biopolymers Due to Reprocessing

Biopolymers are an emerging class of materials being widely pursued due to their ability to degrade in short periods of time. Understanding and evaluating the recyclability of biopolymers is paramount for their sustainable and efficient use in a cost-effective manner. Recycling has proven to be an important solution, to control environmental and waste management issues. This paper presents the first recycling assessment of Solanyl, Bioflex, polylactic acid (PLA) and PHBV using a melt extrusion process. All biopolymers were subjected to five reprocessing cycles. The thermal and mechanical properties of the biopolymers were investigated by GPC, TGA, DSC, mechanical test, and DMA. The molecular weights of Bioflex and Solanyl showed no susceptible effect of the recycling process, however, a significant reduction was observed in the molecular weight of PLA and PHBV. The inherent thermo-mechanical degradation in PHBV and PLA resulted in 20% and 7% reduction in storage modulus, respectively while minimal reduction was observed in the storage modulus of Bioflex and Solanyl. As expected from the Florry-Fox equation, recycled PLA with a high reduction in molecular weight (78%) experienced 9% reduction in glass transition temperature. Bioflex and Solanyl showed 5% and 2% reduction in molecular weight and experienced only 2% reduction in glass transition temperature. These findings highlight the recyclability potential of Bioflex and Solanyl over PLA and PHBV.

Enhancing Electroresponsive Electrorheological Effect and Temperature Dependence of Poly(ionic liquid) Particles by Hard Core Confinement

Monodisperse core-shell-structured SiO₂@poly(ionic liquid) (SiO₂@PIL) particles are prepared by the polymerization of ionic liquid monomer on the surface of methacryloxypropyltrimethoxysilane-modified SiO₂ particles. The electroresponsive electrorheological (ER) effect of SiO₂@PIL particles when dispersed in insulating carrier liquid is investigated and compared with that of pure poly(ionic liquid) (PIL) particles based on temperature-modulated rheology under electric fields. It is demonstrated that hard SiO₂ core not only enhances the ER effect of PIL particles but also improves the temperature dependence of ER effect. By dielectric spectroscopy analysis, the mechanism behind the property enhancement was discussed. It indicates that the hard SiO₂ core can not only increase the interfacial polarization strength of SiO₂@PIL particles by core-shell architecture but also restrain the segment relaxation or softening of the PIL shell and influence the ion dynamics above the calorimetric glass transition of PILs by the so called "substrate confinement effect", and this should be responsible for the enhanced electroresponsive ER effect and temperature stability of the SiO₂@PIL particles.

Do Carbon Nanotubes Improve the Thermomechanical Properties of Benzoxazine Thermosets?

Fillers are widely used to improve the thermomechanical response of polymer matrices, yet often in an unpredictable manner because the relationships between the mechanical properties of the composite material and the primary (chemical) structure of its molecular components have remained elusive so far. Here, we report on a combined theoretical and experimental study of the structural and thermomechanical properties of carbon nanotube (CNT)-reinforced polybenzoxazine resins, as prepared from two monomers that only differ by the presence of two ethyl side groups. Remarkably, while addition of CNT is found to have no impact on the glass-transition temperature ( T_g) of the ethyl-decorated resin, the corresponding ethyl-free composite features a surge by ∼47 °C (50 °C) in T_g, from molecular dynamics simulations (dynamic mechanical analysis measurements), as compared to the neat resin. Through a detailed theoretical analysis, we propose a microscopic picture for the differences in the thermomechanical properties of the resins, which sheds light on the relative importance of network topology, cross-link and hydrogen-bond density, chain mobility, and free volume.

Grafting density dominant glass transition of dry polystyrene brushes

The effects of the grafting densities (σ_p), molecular weights (M_n) and thicknesses of dry polystyrene (PS) brushes on their glass transition temperature (T) were investigated by ellipsometry. The results show that T strongly depends on the grafting density of the PS brushes. The T of the PS brushes with σ_p > 0.30 increases with decreasing M_n (or brush thickness) and is mainly dominated by entropic effects, in which the grafted chains are highly extended along the film thickness direction resulting in a sharp reduction in configurational entropy. The T of PS brushes with σ_p < 0.30 decreases with decreasing M_n (or brush thickness) which is mainly dominated by surface effects. For intermediate-density brushes (σ_p = 0.30), T becomes independent of M_n or brush thickness. The reason for this grafting density dependence of T is attributed to the transition of the PS brush conformation from mushroom-to-brush.

Glass transition of polymers in bulk, confined geometries, and near interfaces

When cooled or pressurized, polymer melts exhibit a tremendous reduction in molecular mobility. If the process is performed at a constant rate, the structural relaxation time of the liquid eventually exceeds the time allowed for equilibration. This brings the system out of equilibrium, and the liquid is operationally defined as a glass-a solid lacking long-range order. Despite almost 100 years of research on the (liquid/)glass transition, it is not yet clear which molecular mechanisms are responsible for the unique slow-down in molecular dynamics. In this review, we first introduce the reader to experimental methodologies, theories, and simulations of glassy polymer dynamics and vitrification. We then analyse the impact of connectivity, structure, and chain environment on molecular motion at the length scale of a few monomers, as well as how macromolecular architecture affects the glass transition of non-linear polymers. We then discuss a revised picture of nanoconfinement, going beyond a simple picture based on interfacial interactions and surface/volume ratio. Analysis of a large body of experimental evidence, results from molecular simulations, and predictions from theory supports, instead, a more complex framework where other parameters are relevant. We focus discussion specifically on local order, free volume, irreversible chain adsorption, the Debye-Waller factor of confined and confining media, chain rigidity, and the absolute value of the vitrification temperature. We end by highlighting the molecular origin of distributions in relaxation times and glass transition temperatures which exceed, by far, the size of a chain. Fast relaxation modes, almost universally present at the free surface between polymer and air, are also remarked upon. These modes relax at rates far larger than those characteristic of glassy dynamics in bulk. We speculate on how these may be a signature of unique relaxation processes occurring in confined or heterogeneous polymeric systems.

Role of Dynamical Heterogeneities on the Mechanical Response of Confined Polymer

Confinement induces various modifications in the dynamics of polymers as compared to bulk. We focus here on the role of dynamical heterogeneities on the mechanics of confined polymers. Using a simple model that allows computation of the mechanical response over 10 decades in frequency, we show that the local mechanical coupling controlling the macroscopic response in the bulk disappears in a confined geometry. The slowest domains significantly contribute to the mechanical response for increasing confinement. As a consequence, the apparent glass transition is broadened and shifted towards lower frequencies as confinement increases. We compare our numerical predictions with experiments performed on poly(ethylacrylate) chains in model filled elastomers. We suggest that the change of elastic coupling between domains induced by confinement should contribute significantly to the polymer mobility shift observed on filled systems.

Local Dielectric Property Detection of the Interface between Nanoparticle and Polymer in Nanocomposite Dielectrics

The interface between nanoparticles and polymer matrix is considered to have an important effect on the properties of nanocomposites. In this experimental study, electrostatic force microscopy (EFM) is used to study the local dielectric property of the interface of low density polyethylene (LDPE)/TiO₂ nanocomposites at nanometer scale. The results show that the addition of TiO₂ nanoparticles leads to a decrease in local permittivity. We then carry out the finite element simulation and confirm that the decrease of local permittivity is related to the effect of interface. According to the results, we propose several models and validate the dielectric effect and range effect of interface. Through the analysis of DSC and solid-state NMR results, we find TiO₂ nanoparticles can suppress the mobility of local chain segments in the interface, which influences the dipolar polarization of chain segments in the interface and eventually results in a decrease in local permittivity. It is believed the results would provide important hint to the research of the interface in future research.

Effect of geometric curvature on vitrification behavior for polymer nanotubes confined in anodic aluminum oxide templates

The glass transition behavior of polystyrene (PS) nanotubes confined in cylindrical alumina nanopores was studied as a function of pore diameter (d) and polymer tube thickness (δ). Both the calorimetric glass transition temperature and the microstructure measured by a nonradiative energy transfer method indicated that the polymer nanotube, or concave polymer thin film, exhibited significant differences in vitrification behavior compared to the planar one. A closer interchain proximity and an increased T_{g} were observed for polymer nanotubes with respect to the bulk polymer. T_{g} for polymer nanotubes was primarily dependent on the curvature radius d of the template, while it was less dependent on the thickness δ of the PS tube wall in the range of 11-23 nm. For small nanotubes (d=55nm), the T_{g} increased as high as 18 °C above the bulk value. This vitrified property reverted back to the bulk value when the substrate was chemically removed, which indicated the crucial importance of the interfacial effect imposed by the hard wall with a concave geometry.

Dynamics-based selective 2D (1)H/(1)H chemical shift correlation spectroscopy under ultrafast MAS conditions

Dynamics plays important roles in determining the physical, chemical, and functional properties of a variety of chemical and biological materials. However, a material (such as a polymer) generally has mobile and rigid regions in order to have high strength and toughness at the same time. Therefore, it is difficult to measure the role of mobile phase without being affected by the rigid components. Herein, we propose a highly sensitive solid-state NMR approach that utilizes a dipolar-coupling based filter (composed of 12 equally spaced 90° RF pulses) to selectively measure the correlation of (1)H chemical shifts from the mobile regions of a material. It is interesting to find that the rotor-synchronized dipolar filter strength decreases with increasing inter-pulse delay between the 90° pulses, whereas the dipolar filter strength increases with increasing inter-pulse delay under static conditions. In this study, we also demonstrate the unique advantages of proton-detection under ultrafast magic-angle-spinning conditions to enhance the spectral resolution and sensitivity for studies on small molecules as well as multi-phase polymers. Our results further demonstrate the use of finite-pulse radio-frequency driven recoupling pulse sequence to efficiently recouple weak proton-proton dipolar couplings in the dynamic regions of a molecule and to facilitate the fast acquisition of (1)H/(1)H correlation spectrum compared to the traditional 2D NOESY (Nuclear Overhauser effect spectroscopy) experiment. We believe that the proposed approach is beneficial to study mobile components in multi-phase systems, such as block copolymers, polymer blends, nanocomposites, heterogeneous amyloid mixture of oligomers and fibers, and other materials.

Observation of strong nano-effect via tuning distributed architecture of graphene oxide in poly(propylene carbonate)

For optimum reinforcement in polymer nanocomposite, a critical challenge is to realize the full 'nano-effect' of nanofillers at a high content, which is largely hindered by the strong tendency to aggregation of nanofillers. Here, by using a solvent-exchange and solution casting approach, we could incorporate a high-content graphene oxide (GO) into a soft biodegradable CO2-based poly(propylene carbonate) (PPC) up to 20 wt% with excellent dispersion. Based on this, the distributed architecture of GO could be tuned from a 'GO dotted dispersion' and 'GO network' to strong 'GO co-continuous structure' with increasing GO content. As a result, a very strong 'nano-effect' of GO in the PPC matrix was observed: (1) the glass transition temperature of PPC was improved from 25 to 45 ° C for slightly confined molecular chains, and even to 100 ° C for highly confined ones; (2) the modified PPC showed drastically enhanced high-temperature mechanical properties, comparable to those of traditional polymers such as polypropylene (PP) and biopolymer poly(lactic acid) (PLA); and (3) such modified PPC exhibited an exciting solvent resistance compared to neat PPC. Our work provides an example to improve the high-temperature properties of a polymer via formation of filler co-continuous structure.

Characterization of the mobility and reactivity of water molecules on TiO2 nanoparticles by 1H solid-state nuclear magnetic resonance

Understanding interfacial water behavior is essential to improving our understanding of the surface chemistry and interfacial properties of nanomaterials. Here using 1H solid-state nuclear magnetic resonance (1H SSNMR), we successfully monitored ligand exchange reaction between oleylamine (OLA) and adsorbed water on titanium dioxide nanoparticles (TiO2 NPs). Three different types of interfacial waters with different reactivities were distinguished. The mobility of the adsorbed water molecules was characterized by dipolar filtered 1H SSNMR. Our experimental results demonstrate that the adsorbed water can be categorized into three different layers: (i) rigid water species with restricted mobility closest to the surface of TiO2 NPs, (ii) less mobile water species weakly confined on TiO2 NPs, and (iii) water molecules with high mobility. Water in the third layer could be replaced by OLA, while water in the first and second layers remained intact. The finding that the interfacial water with the highest mobility has the strongest reactivity has guiding significance for tailoring the hydrophilic and hydrophobic properties of TiO2 NPs.