N-doped catalytic graphitized hard carbon for high-performance lithium/sodium-ion batteries

One-Pot Direct Mechanochemical Silicon Replacement of Sodium Fluorosilicate into Sodium Fluorozirconate and Functionalization of Graphite for Enhanced Sodium-Ion Storage

Efficient sodium ion storage in graphite is as yet unattainable, because of the thermodynamic instability of sodium ion intercalates-graphite compounds. In this work, sodium fluorozirconate (Na3ZrF7, SFZ) functionalized graphite (SFZ-G) is designed and prepared by the in situ mechanochemical silicon (Si) replacement of sodium fluorosilicate (Na2SiF6, SFS) and functionalization of graphite at the same time. During the mechanochemical process, the atomic Si in SFS is directly replaced by atomic zirconium (Zr) from the zirconium oxide (ZrO2) balls and container in the presence of graphite, forming SFZ-G. The resulting SFZ-G, working as an anode material for sodium ion storage, shows a significantly enhanced capacity of 418.7 mAh g-1 at 0.1 C-rate, compared to pristine graphite (35 mAh g-1) and simply ball-milled graphite (BM-G, 200 mAh g-1). In addition, the SFZ-G exhibits stable sodium-ion storage performance with 86% of its initial capacity retention after 1000 cycles at 2.0 C-rate.

Synthesis of multi-cavity mesoporous carbon nanospheres through solvent-induced self-assembly: Anode material for sodium-ion batteries with long-term cycle stability

Mesoporous carbon nanospheres (MCSs) are extensively employed in energy storage applications due to their ordered pore size, large specific surface area (SSA), and abundant active sites, resulting in excellent electrochemical performance for sodium storage. However, challenges persist in achieving precise structural control and stable synthesis reactions for these MCSs. Additionally, employing MCSs with a larger SSA in sodium storage applications can lead to increased side reactions and potential structural instability. To address these issues, we propose a solvent-induced self-assembly method for obtaining high nitrogen-containing multi-cavity MCSs with reduced SSA. The morphology and SSA of the nanospheres can be precisely adjusted by regulating the reaction time. Introducing an amine-phenol bridging structure into the polymer system significantly bolsters the structural and morphological stability of the mesoporous materials. The performance of these novel nanospheres in sodium-ion batteries (SIBs) is remarkable, exhibiting excellent sodium storage capability and exceptional ultra-long cycle stability. At a rate of 0.1 A g-1, the nanospheres achieved a high reversible capacity of 252 mAh g-1, and even after 20,000 cycles at 5 A g-1, a specific capacity of 136 mAh g-1 was retained. In summary, our study presents a novel approach for synthesizing mesoporous carbon materials and offers valuable insights for sodium storage research, opening new possibilities for enhancing energy storage applications.

Polydopamine Derived NaTi2(PO4)3-Carbon Core-Shell Nanostructures for Aqueous Batteries and Deionization Cells

Due to their stability and structural freedom, NASICON-structured materials such as NaTi₂(PO₄)₃ show a lot of promise as active electrode materials for aqueous batteries and deionization cells. However, due to their low intrinsic electronic conductivity, they must usually be composited with carbon to form suitable electrodes for power applications. In this work, two series of NaTi₂(PO₄)₃-carbon composite structures were successfully prepared by different approaches: postsynthetic pyrolytic treatment of citric acid and surface polymerized dopamine. The latter route allows for a superior carbon loading control and yields more uniform and continuous particle coatings. The homogeneity of the polydopamine derived core-shell carbon layer is supported by FTIR, TEM, and XPS analysis. Combustion elemental analysis also indicates significant nitrogen doping in the final carbonaceous structure. The galvanostatic charge and discharge cycling results show similar initial capacities and their retention, but at only half of the carbon loading in polydopamine derived samples. The overall results indicate that careful nanostructure engineering could yield materials with superior properties and stability suitable for various electrochemical applications such as aqueous Na-ion batteries and deionization cells.

A Multifunctional Coating on Sulfur-Containing Carbon-Based Anode for High-Performance Sodium-Ion Batteries

A sulfur doping strategy has been frequently used to improve the sodium storage specific capacity and rate capacity of hard carbon. However, some hard carbon materials have difficulty in preventing the shuttling effect of electrochemical products of sulfur molecules stored in the porous structure of hard carbon, resulting in the poor cycling stability of electrode materials. Here, a multifunctional coating is introduced to comprehensively improve the sodium storage performance of a sulfur-containing carbon-based anode. The physical barrier effect and chemical anchoring effect contributed by the abundant C-S/C-N polarized covalent bond of the N, S-codoped coating (NSC) combine to protect SGCS@NSC from the shuttling effect of soluble polysulfide intermediates. Additionally, the NSC layer can encapsulate the highly dispersed carbon spheres inside a cross-linked three-dimensional conductive network, improving the electrochemical kinetic of the SGCS@NSC electrode. Benefiting from the multifunctional coating, SGCS@NSC exhibits a high capacity of 609 mAh g^-1 at 0.1 A g^-1 and 249 mAh g^-1 at 6.4 A g^-1. Furthermore, the capacity retention of SGCS@NSC is 17.6% higher than that of the uncoated one after 200 cycles at 0.5 A g^-1.

Ecofriendly Synthesis of Waste-Tire-Derived Graphite Nanoflakes by a Low-Temperature Electrochemical Graphitization Process toward a Silicon-Based Anode with a High-Performance Lithium-Ion Battery

Here, the successful transformation of graphitic carbon with a high degree of graphitization and a nanoflake structure from pyrolytic tire carbon black was demonstrated. First, amorphous carbon black with a porous structure was obtained after pyrolysis and simple preacid treatments. Subsequently, the carbon black was converted into a highly graphitic structure at a relatively low temperature (850 °C) through a facile electrochemical route using molten salt, which is ecofriendly and has high potential for large-scale graphitization compared to conventional incineration techniques. Moreover, we further improved the crystallinity and uniformity of the product simultaneously by directly mixing the metal oxide catalyst Fe₂O₃ with a carbon precursor. The mechanism of this metal-catalyzed electrochemical graphitization has been discussed in detail. To confirm their potential in practical applications, the as-prepared graphitized nanoflakes were used as conductive additives for silicon anodes in lithium-ion batteries, which showed a performance comparable to those utilizing commercial Super-P additives, exhibiting an initial Coulombic efficiency of approximately 79.7% and a high capacity retention of approximately 45.8% after 100 cycles with a reversible capacity of 1220 mAh g^-1 at a current rate of 400 mA g^-1. Hence, successfully recovered waste-tire-derived carbon black utilizing a low-temperature Fe₂O₃-catalyzed electrochemical process opens a pathway in low-temperature graphitization toward a sustainable value-added application in the field of energy storage.

Biomass Alginate Derived Oxygen-Enriched Carbonaceous Materials with Partially Graphitic Nanolayers for High Performance Anodes in Lithium-Ion Batteries

Lithium-ion batteries with high reversible capacity, high-rate capability, and extended cycle life are vital for future consumer electronics and renewable energy storage. There is a great deal of interest in developing novel types of carbonaceous materials to boost lithium storage properties due to the inadequate properties of conventional graphite anodes. In this study, we describe a facile and low-cost approach for the synthesis of oxygen-doped hierarchically porous carbons with partially graphitic nanolayers (Alg-C) from pyrolyzed Na-alginate biopolymers without resorting to any kind of activation step. The obtained Alg-C samples were analyzed using various techniques, such as X-ray diffraction, Raman, X-ray photoelectron spectroscopy, scanning electron microscope, and transmission electron microscope, to determine their structure and morphology. When serving as lithium storage anodes, the as-prepared Alg-C electrodes have outstanding electrochemical features, such as a high-rate capability (120 mAh g^-1 at 3000 mA g^-1) and extended cycling lifetimes over 5000 cycles. The post-cycle morphologies ultimately provide evidence of the distinct structural characteristics of the Alg-C electrodes. These preliminary findings suggest that alginate-derived carbonaceous materials may have intensive potential for next-generation energy storage and other related applications.

Design of Three-Dimensional Metallic Biphenylene Networks for Na-Ion Battery Anodes with a Record High Capacity

Na-ion batteries (NIBs) capture intensive research interest in large-scale energy storage applications because of sodium's abundant resources and low cost. However, the low capacity, poor conductivity, and short cycle life of the commonly used anodes are the main challenges in developing advanced NIBs. Here, stimulated by the recent successful synthesis of biphenylene [Science 2021, 372, 852], we show that these problems can be curbed by assembling armchair biphenylene nanoribbons of different widths into three-dimensional architectures, which lead to homogeneously distributed nanopores with robust structural and mechanical stability. Through density functional theory and molecular dynamics calculations combined with the tight-binding model, we find that the assembled 3D biphenylene structures are metallic and thermally stable up to 2500 K, where the metallicity is further identified to originate from the p_z-orbitals (π-bonds) of the sp² carbon atoms. Especially, the optimal assembled structures HexC28 (HexC46) deliver a gravimetric capacity of 956 (1165) mA h g^-1 and a volumetric capacity of 1109 (874) mA h mL^-1, which are much higher than those of graphite and hard carbon anodes. Moreover, they also show a suitable average potential, negligible volume change, and low diffusion energy barrier. These findings demonstrate that assembling biphenylene nanoribbons is a promising strategy for designing next-generation NIB anodes.

Structural and Interfacial Characterization of a Sustainable Si/Hard Carbon Composite Anode for Lithium-Ion Batteries

The effects of a biomass-derived hard carbon matrix and a sustainable cross-linked binder are investigated as electrode components for a silicon-based anode in lithium-ion half-cells, in order to reduce the capacity fade due to volume expansion and shrinkage upon cycling. Ex situ Raman spectroscopy and impedance spectroscopy are used to deeply investigate the structural and interfacial properties of the material within a single cycle and upon cycling. An effective buffering of the volume changes of the composite electrode is evidenced, even at a high Si content up to 30% in the formulation, resulting in the retention of structural and interfacial integrity. As a result, a high capacity performance and a very good rate capability are displayed even at high current densities, with a stable cycling behavior and low polarization effects.

Investigation of pyrolysed anthracite as an anode material for sodium ion batteries

Due to the increasingly serious problems of the greenhouse effect and environmental pollution caused by the continuous consumption of traditional fossil energy, renewable and clean energy (such as solar energy and wind energy) is facing new opportunities and challenges.

Nitrogen-Doped Carbon Aerogels Derived from Starch Biomass with Improved Electrochemical Properties for Li-Ion Batteries

Among all advanced anode materials, graphite is regarded as leading and still-unrivaled. However, in the modern world, graphite-based anodes cannot fully satisfy the customers because of its insufficient value of specific capacity. Other limitations are being nonrenewable, restricted natural graphite resources, or harsh conditions required for artificial graphite production. All things considered, many efforts have been made in the investigation of novel carbonaceous materials with desired properties produced from natural, renewable resources via facile, low-cost, and environmentally friendly methods. In this work, we obtained N-doped, starch-based carbon aerogels using melamine and N₂ pyrolysis as the source of nitrogen. The materials were characterized by X-ray powder diffraction, elemental analysis, X-ray photoelectron spectroscopy, galvanostatic charge-discharge tests, cyclic voltammetry, and electrochemical impedance spectroscopy. Depending on the doping method and the nitrogen amount, synthesized samples achieved different electrochemical behavior. N-doped, bioderived carbons exhibit far better electrochemical properties in comparison with pristine ones. Materials with the optimal amount of nitrogen (such as MCAGPS-N8.0%-carbon aerogel made from potato starch modified with melamine and CAGPS-N1.2%-carbon aerogel made from potato starch modified by N₂ pyrolysis) are also competitive to graphite, especially for high-performance battery applications. N-doping can enhance the efficiency of Li-ion cells mostly by inducing more defects in the carbon matrix, improving the binding ability of Li⁺ and charge-transfer process.

Algae-derived hard carbon anodes for Na-ion batteries

Abstract

In this work, the production of low cost and environment friendly anodes for sodium ion batteries is investigated. Algae are selected as bio-source of non-graphitic Hard Carbon (HC) with open structure acting as intercalation active material for Na ions storage. Chlorella vulgaris algae were pyrolyzed at temperatures comprised between 800 and 1100 °C. The decomposition products have been characterized with Scanning Electrode Microscope (SEM) and X-Ray Diffraction (XRD) analyses and their structure compared to one of the synthetic commercial HC. Thermogravimetric analysis (TGA) allowed to assess the decomposition process throughout the selected temperature scan. The obtained algae-derived HC is tested as anodic material for Na-ion battery, investigating the effect of pyrolysis temperature on the electrochemical behaviour. Their performances are compared with respect to a commercial synthetic HC active material. The results allow to consider algae as an environmentally benign and sustainable high added-value material for the production of HC anodes for Na-ion batteries.

Graphic abstract

Sustainable Anodes for Lithium- and Sodium-Ion Batteries Based on Coffee Ground-Derived Hard Carbon and Green Binders

The reuse and recycling of products, leading to the utilization of wastes as key resources in a closed loop, is a great opportunity for the market in terms of added value and reduced environmental impact. In this context, producing carbonaceous anode materials starting from raw materials derived from food waste appears to be a possible approach to enhance the overall sustainability of the energy storage value chain, including Li-ion (LIBs) and Na-ion batteries (NIBs). In this framework, we show the behavior of anodes for LIBs and NIBs prepared with coffee ground-derived hard carbon as active material, combined with green binders such as Na-carboxymethyl cellulose (CMC), alginate (Alg), or polyacrylic acid (PAA). In order to evaluate the effect of the various binders on the charge/discharge performance, structural and electrochemical investigations are carried out. The electrochemical characterization reveals that the alginate-based anode, used for NIBs, delivers much enhanced charge/discharge performance and capacity retention. On the other hand, the use of the CMC-based electrode as LIBs anode delivers the best performance in terms of discharge capacity, while the PAA-based electrode shows enhanced cycling stability. As a result, the utilization of anode materials derived from an abundant food waste, in synergy with the use of green binders and formulations, appears to be a viable opportunity for the development of efficient and sustainable Li-ion and Na-ion batteries.

Nickel-Embedded Carbon Materials Derived from Wheat Flour for Li-Ion Storage

The biomass-based carbons anode materials have drawn significant attention because of admirable electrochemical performance on account of their nontoxicity and abundance resources. Herein, a novel type of nickel-embedded carbon material (nickel@carbon) is prepared by carbonizing the dough which is synthesized by mixing wheat flour and nickel nitrate as anode material in lithium-ion batteries. In the course of the carbonization process, the wheat flour is employed as a carbon precursor, while the nickel nitrate is introduced as both a graphitization catalyst and a pore-forming agent. The in situ formed Ni nanoparticles play a crucial role in catalyzing graphitization and regulating the carbon nanocrystalline structure. Mainly owing to the graphite-like carbon microcrystalline structure and the microporosity structure, the NC-600 sample exhibits a favorable reversible capacity (700.8 mAh g⁻¹ at 0.1 A g⁻¹ after 200 cycles), good rate performance (51.3 mAh g⁻¹ at 20 A g⁻¹), and long-cycling durability (257.25 mAh g⁻¹ at 1 A g⁻¹ after 800 cycles). Hence, this work proposes a promising inexpensive and highly sustainable biomass-based carbon anode material with superior electrochemical properties in LIBs.

Synthesis of Metal Oxide/Carbon Nanofibers via Biostructure Confinement as High-Capacity Anode Materials

For applications in energy storage and conversion, many metal oxide (MO)/C composite fibers have been synthesized using cellulose as the template. However, MO particles in carbon fibers usually experience anomalous growth to a size of >200 nm, which is detrimental to the overall performance of the composite. In this paper, we report the successful development of a generic approach to synthesize a fiber composite with highly dispersed MO nanoparticles (10-80 nm) via simple swelling, nitrogen doping, and carbonization of the cellulose microfibril. The growth of the MO nanoparticles is confined by the structure of the microfibrils. Density functional theory calculation further reveals that the doped N atoms supply ample nucleation sites for size confinement of the nanoparticles. The encapsulation structure of small MO nanoparticles in the conductive carbon matrix improves their electrochemical performance. For example, the formed SnO_x/carbon nanocomposite exhibits high specific capacities of 1011.0 mA h g^-1 at 0.5 A g^-1 and 581.8 mA h g^-1 at 5 A g^-1. Moreover, the fiber-like nanocomposite can be combined with carbon nanotubes to form a flexible binder-free electrode with a capacity of ∼10 mA h cm^-2, far beyond the commercial level. The process developed in this study offers an alternative approach to sophisticated electrospinning for the synthesis of other fiber-like MO/carbon nanocomposites for versatile applications.

Fabrication of porous Na3V2(PO4)3/reduced graphene oxide hollow spheres with enhanced sodium storage performance

Sodium-ion batteries (SIBs) have long been recognized as a potential substitute for lithium-ion batteries, while their practical application is greatly hindered owing to the absence of suitable cathode materials with improved rate capability and prolonged cycling life. Na₃V₂(PO₄)₃ (NVP) has drawn extensive attention among the cathode materials for SIBs because of its fast Na⁺-transportable framework which enables high-speed charge transfer, but the poor electric conductivity of NVP significantly restricts the Na⁺ diffusion. To tackle this issue, in this work, porous NVP/reduced graphene oxide hollow spheres (NVP/rGO HSs) are constructed via a spray drying strategy. Due to the unique porous hollow architecture, the synthesized compound manifests a high reversible capacity of 116 mAh g^-1 at 1 C (1 C = 118 mA g^-1), an outstanding high-rate capability of 107.5 mAh g^-1 at 10 C and 98.5 mAh g^-1 at 20 C, as well as a stable cycling performance of 109 mAh g^-1 after 400 cycles at 1 C and 73.1 mAh g^-1 after 1000 cycles at 10 C. Moreover, galvanostatic intermittent titration technique demonstrates that the Na⁺ diffusion coefficient of NVP/rGO HSs is an order of magnitude larger than the pristine NVP. The remarkable electrochemical properties of NVP/rGO HSs in full cells further enable it a potential cathode for SIBs.

Recyclable High-Performance Polymer Electrolyte Based on a Modified Methyl Cellulose-Lithium Trifluoromethanesulfonate Salt Composite for Sustainable Energy Systems

Although energy-storage devices based on Li ions are considered as the most prominent candidates for immediate application in the near future, concerns with regard to their stability, safety, and environmental impact still remain. As a solution, the development of all-solid-state energy-storage devices with enhanced stability is proposed. A new eco-friendly polymer electrolyte has been synthesized by incorporating lithium trifluoromethanesulfonate into chemically modified methyl cellulose (LiTFS-LiSMC). The transparent and flexible electrolyte exhibits a good conductivity of near 1 mS cm^-1 . An all-solid-state supercapacitor fabricated from 20 wt % LiTFS-LiSMC shows comparable specific capacitances to a standard liquid-electrolyte supercapacitor and an excellent stability even after 20 000 charge-discharge cycles. The electrolyte is also compatible with patterned carbon, which enables the simple fabrication of micro-supercapacitors. In addition, the LiTFS-LiSMC electrolyte can be recycled and reused more than 20 times with negligible change in its performance. Thus, it is a promising material for sustainable energy-storage devices.

Rational Design of 1D Partially Graphitized N-Doped Hierarchical Porous Carbon with Uniaxially Packed Carbon Nanotubes for High-Performance Lithium-Ion Batteries

N-doped hierarchical porous carbon with uniaxially packed carbon nanotubes (CNTs) was prepared by copolymer single-nozzle electrospinning, carbonization, and KOH activation. Densely and uniaxially aligned CNTs improve the electrical conductivity and act as a structural scaffold, enhancing the electrochemical performance of the anode. A partially graphitized N-doped carbon shell, which has a rapid ion accessible pore network and abundant redox sites, was designed to expand the redox sites from the surface of the material to the whole material, including the inner part. As an anode, this material exhibited a superior reversible capacity of 1814.3 mA h g^-1 at 50 mA g^-1 and of 850.1 mA h g^-1 at 1000 mA g^-1. Furthermore, the reversible capacity decreased by only 36% after 400 cycles and showed superior rate capability to that of the same material without CNTs, indicating that the CNT acted successfully as a structural scaffold and enhanced the electrical conductivity. This study not only allowed the rational design of the ideal structure of CNT-based carbonaceous anode material, which has both a rapid ion accessible structure and fast electron-transfer path, but also shed light on a potential strategy by which to use CNTs to modify the nitrogen bonding configuration in N-doped carbon for better electrochemical performance.