S defect-rich MoS2 aerogel with hierarchical porous structure: Efficient photocatalysis and convenient reuse for removal of organic dyes

To avoid the difficulty of separating solids from liquids when reusing powder photocatalysts, 3D stereoscopic photocatalysts were constructed. In this study, three-dimensional S defect-rich MoS2 hierarchical aerogel was prepared by chemical cross-linking of functional ultrathin 2D MoS2. Its phase, micro-morphology and structure were characterized, and it was used in the study of photocatalytic degradation of organic pollutants. Of the samples tested, MS@CA-3 (i.e., defect-rich 3D MoS2 aerogel with a loading of 30 mg of defect-rich MoS2) exhibited the best photocatalytic activity due to its suitable load, good light transmission, and a degradation rate of up to 91.0% after 3 h. In addition, MS@CA-3 aerogel offers high recyclability and structural stability, and the degradation rate of the organic pollutant methylene blue decreases only 9.8% after more than ten cycles of photocatalytic degradation. It combines the high catalytic performance of S defect-rich 2D MoS2 and the convenient reusability of hierarchical porous aerogel. This study provides valuable data and a reference for the practical promotion and application of photocatalytic technology in the field of environmental remediation.

Insights into starch-based gels: Selection, fabrication, and application

Starch a natural polymer, has made significant advancements in recent decades, offering superior performance and versatility compared to synthetic materials. This review discusses up-to-date diverse applications of starch gels, their fabrication techniques, and their advantages over synthetic materials. Starch gels renewability, biocompatibility, biodegradability, scalability, and affordability make them attractive. Also, advanced theoretical foundations and emerging industrial technologies could further expand their scope and functions inspiring new applications.

Chitosan-based supramolecular aerogel with "skeletal structure" constructed in natural deep eutectic solvents for medical dressings

Bacterial infection of wounds remains one of the major clinical challenges, calling for the urgent development of novel multifunctional biological dressings. In this study, we developed a chitosan-based supramolecular aerogel NADES/PVA/CS, constructed by hydrogen bonding between chitosan, a natural deep eutectic solvents and polyvinyl alcohol, as a novel wound dressing against bacterial infections. The effect of polyvinyl alcohol content and its incorporation within chitosan-based supramolecular aerogels were investigated. The results of antibacterial test and MTT assay showed that it has obvious inhibitory effect on Staphylococcus aureus and Escherichia coli, showing excellent biocompatibility and effectively promotes wound healing. The microstructure of chitosan-based supramolecular aerogel showed that by adjusting the addition amount of polyvinyl alcohol, it could exhibit a perfect skeleton-type 3D network structure, which also made it possess smaller density and larger porosity and exhibit excellent water absorption property, contributing to the wetting of wound surface. More importantly, chitosan-based supramolecular aerogel is an environment-friendly biomaterial, which has been verified by degradability experiment. In a word, these unique advantages provide a broad prospect for the medical application of chitosan-based supramolecular aerogel NADES/PVA/CS, and provide a new strategy for the construction of green polysaccharide medical materials.

Evaluation of ethanol-induced chitosan aerogels with human osteoblast cells

The following article provides an insight into the production of chitosan aerogels as potential materials for tissue engineering. Chitosan aerogels were prepared following two different protocols: formation in ethanol and formation in sodium hydroxide in an ethanol solution. The main objective was to apply a new route to obtain chitosan aerogels with no external cross-linkers and compare the mentioned preparation approaches. Forming chitosan aerogels in ethanol implies a simple, environmentally friendly, and efficient method. The prepared materials showed specific surface areas of up to 450 m2/g, highly porous networks and great mechanical properties. In vitro degradation studies revealed high stability for up to 10 weeks. The differences between the samples were significant. While the chitosan aerogels prepared in ethanol showed superior textural, morphological and mechanical properties, the chitosan aerogels prepared in the sodium hydroxide solution proved that a considerable influence on end properties could be made simply by adjusting the ageing medium. In vitro cell analysis with primary human osteoblasts showed good biocompatibility and pointed towards the potential use of these aerogels for orthopedic applications. This testing showed further that adjustments in structural properties by sodium hydroxide also come with a cost regarding their suitability to host bone cells.

Green surface functionalization of chitosan with spent tea waste extract for the development of an efficient adsorbent for aspirin removal

This study investigates the feasibility of spent tea waste extract (STWE) as a green modifying agent for the modification of chitosan adsorbent towards aspirin removal. Response surface methodology based on Box-Behnken design was employed to find the optimal synthesis parameters (chitosan dosage, spent tea waste concentration, and impregnation time) for aspirin removal. The results revealed that the optimum conditions for preparing chitotea with 84.65% aspirin removal were 2.89 g of chitosan, 18.95 mg/mL of STWE, and 20.72 h of impregnation time. The surface chemistry and characteristics of chitosan were successfully altered and improved by STWE, as evidenced by FESEM, EDX, BET, and FTIR analysis. The adsorption data were best fitted to pseudo 2nd order, followed by chemisorption mechanisms. The maximum adsorption capacity of chitotea was 157.24 mg/g, as fitted by Langmuir, which is impressive for a green adsorbent with a simple synthesis method. Thermodynamic studies demonstrated the endothermic nature of aspirin adsorption onto chitotea.

Effects of deacetylation degree of chitosan on the structure of aerogels

Chitosan aerogels, obtained by (supercritical) CO2 drying of hydrogels, are novel adsorbents because of their large surface area and high porosity. Intrinsic properties of chitosan such as molecular weight (MW) and degree of deacetylation (DDA) had large impacts on the characteristics of chitosan aerogels. Although there are a few studies about the effects of solely DDA or MW on aerogel structure, none of them has focused on the mutual effects. The study aims to investigate the combined effects of MW and DDA of chitosan on aerogel properties. Hydrogels were produced in beads form by physical gelation of the chitosan solutions (2 % w/v in acetic acid of 1 %, v/v) in an alkaline environment (NaOH, 4 N). Supercritical CO2 dried aerogels were examined with respect to the bulk density, diameter as well as pore characteristics, and surface area by Barrett-Joyner-Halenda (BJH) and Brunauer-Emmett-Teller (BET) methods, respectively. Morphologies of aerogels were also examined by Scanning Electron Microscopy (SEM) images and structural changes of aerogels were observed by Fourier Transform Infrared (FTIR) Spectroscopy. Additional to BET-BJH analysis, proton relaxation dispersion was measured by Fast Field Cycling NMR (FFC-NMR) to determine the pore volume of the aerogels. Compact structures were obtained for higher MW chitosan and lower MW chitosans with higher DDA increasing the aerogel diameters. All types of aerogels obtained by different chitosan characteristics (MW and DDA) showed a porous structure and the highest DDA with the lowest MW caused the minimum bulk density with the highest water absorption rate. Although different N2 adsorption-desorption profiles were obtained in terms of pore volumes; all aerogels had Type IV isotherms with Type H1 hysteresis curve. FFC-NMR experiments showed that the coherence length values were associated with the pore volumes and FFC-NMR experiments were found to be meaningful as supportive experiments for the characterization of aerogels.

Hollow Particles Obtained by Prilling and Supercritical Drying as a Potential Conformable Dressing for Chronic Wounds

The production of aerogels for different applications has been widely known, but the use of polysaccharide-based aerogels for pharmaceutical applications, specifically as drug carriers for wound healing, is being recently explored. The main focus of this work is the production and characterization of drug-loaded aerogel capsules through prilling in tandem with supercritical extraction. In particular, drug-loaded particles were produced by a recently developed inverse gelation method through prilling in a coaxial configuration. Particles were loaded with ketoprofen lysinate, which was used as a model drug. The core-shell particles manufactured by prilling were subjected to a supercritical drying process with CO₂ that led to capsules formed by a wide hollow cavity and a tunable thin aerogel layer (40 μm) made of alginate, which presented good textural properties in terms of porosity (89.9% and 95.3%) and a surface area up to 417.0 m²/g. Such properties allowed the hollow aerogel particles to absorb a high amount of wound fluid moving very quickly (less than 30 s) into a conformable hydrogel in the wound cavity, prolonging drug release (till 72 h) due to the in situ formed hydrogel that acted as a barrier to drug diffusion.

Evaluating the Effect of Iron(III) in the Preparation of a Conductive Porous Composite Using a Biomass Waste-Based Starch Template

In this work, the effect of iron(III) in the preparation of a conductive porous composite using a biomass waste-based starch template was evaluated. Biopolymers are obtained from natural sources, for instance, starch from potato waste, and its conversion into value-added products is highly significant in a circular economy. The biomass starch-based conductive cryogel was polymerized via chemical oxidation of 3,4-ethylenedioxythiophene (EDOT) using iron(III) p-toluenesulfonate as a strategy to functionalize porous biopolymers. Thermal, spectrophotometric, physical, and chemical properties of the starch template, starch/iron(III), and the conductive polymer composites were evaluated. The impedance data of the conductive polymer deposited onto the starch template confirmed that at a longer soaking time, the electrical performance of the composite was improved, slightly modifying its microstructure. The functionalization of porous cryogels and aerogels using polysaccharides as raw materials is of great interest for applications in electronic, environmental, and biological fields.

Micro-mechanism insights into the adsorption of anionic dyes using quaternary ammonium-functionalised chitosan aerogels

The development of adsorbents with outstanding adsorption capacities, wide versatility, and excellent recyclability for the removal of organic dyes remains a challenge. In this study, a quaternised chitosan-based aerogel (QCSA) was fabricated via a facile method to effectively treat concomitant anionic dyes. Porous QCSA with high hydrophilicity, nontoxicity, excellent thermal stability, and sustainability exhibits adsorption properties superior to most previously reported adsorbents. The equilibrium adsorption capacities for Congo red, Sunset yellow, and Methyl orange were 1259.6, 550.2, and 607.5 mg/g, respectively. Notably, the spent QCSA exhibits excellent cyclic performance. The multilayer adsorption, external-internal mass transfer resistance, and adsorption on the active site models were employed to enable a more accurate description of the dynamic characteristics, confirming that double-layer chemisorption was the dominant process. A quantitative analysis of the electrostatic potential and the independent gradient model further verified that electrostatic interactions, hydrogen bonding, and van der Waals forces led to the highly efficient adsorption of dye molecules. Therefore, the eco-friendly and recyclable QCSA is a promising adsorbent for trapping anionic dyes from aquatic systems.

Development of Regular Hydrophobic Silica Aerogel Microspheres for Efficient Oil Adsorption

The objective of this research was to develop new hydrophobic silica aerogel microspheres (HSAMs) with water glass and hexmethyldisilazane for oil adsorption. The effects of the hexmethyldisilazane concentration and drying method on the structure and organic liquid adsorption capacity were investigated. The hexmethyldisilazane concentration of the modification solution did not influence the microstructure and pore structure in a noteworthy manner, which depended more on the drying method. Vacuum drying led to more volume shrinkage of the silica gel microsphere (SGM) than supercritical CO₂ drying, thus resulting in a larger apparent density, lower pore volume, narrower pore size distribution, and more compact network. Owing to the large pore volume and pore size, the HSAMs synthesized via supercritical CO₂ drying had a larger organic liquid adsorption capacity. The adsorption capacities of the HSAMs with pore volumes of 4.04-6.44 cm³/g for colza oil, vacuum pump oil, and hexane are up to 18.3, 18.9, and 11.8 g/g, respectively, higher than for their state-of-the-art counterparts. The new sorbent preparation method is facile, cost-effective, safe, and ecofriendly, and the resulting HSAMs are exceptional in capacity, stability, and regenerability.

Metformin delivery via iontophoresis based on κ-carrageenan cryogels

Transdermal drug delivery system (TDDS) is the system for transmitting a drug through the skin into the blood circulation. In this work, κ-Carrageenan (κC) was used as the drug matrix material. The porous κC matrices were fabricated by dissolving the κC in deionized water to obtain hydrogels and then using the freeze-dryer to obtain cryogels. The porous (κC) matrices showed interconnected pore sizes varying between 6.05 to 25.8 nm. In the drug release experiments, the drug diffusion coefficient increased and the drug release duration was reduced with decreasing κC concentration due to the larger κC pore sizes. The diffusion coefficient increased with a shorter release time under the applied electric strength of +1.0 V due to the electro-repulsive force between the Metformin and the anode. For the drug release-permeation of the κC 0.8 % v/v cryogel through the pig skin under applied positive electrical potentials, the amounts of drug release-permeation and diffusion coefficients were enhanced with shorter durations relative to without electrical potential. The κC 0.8 % v/v matrix at the applied electric strength of +6.0 V has been shown here to be potential to be used as the Metformin transdermal controlled delivery patch for abdominal obesity and diabetes.

A Brief Evaluation of Pore Structure Determination for Bioaerogels

This review discusses the most commonly employed methods for determining pore size and pore size distribution in bioaerogels. Aerogels are materials with high porosity and large surface areas. Most of their pores are in the range of mesopores, between 2 and 50 nm. They often have smaller or larger pores, which presents a significant challenge in determining the exact mean pore size and pore size distribution in such materials. The precision and actual value of the pore size are of considerable importance since pore size and pore size distribution are among the main properties of aerogels and are often directly connected with the final application of those materials. However, many recently published papers discuss or present pore size as one of the essential achievements despite the misinterpretation or the wrong assignments of pore size determination. This review will help future research and publications evaluate the pore size of aerogels more precisely and discuss it correctly. The study covers methods such as gas adsorption, from which BJH and DFT models are often used, SEM, mercury porosimetry, and thermoporometry. The methods are described, and the results obtained are discussed. The following paper shows that there is still no precise method for determining pore size distribution or mean pore size in aerogels until now. Knowing that, it is expected that this field will evolve in the future.

Composite Aerogel Comprised of Sodium Alginate and Bentonite via Supercritical CO2 Drying: An Efficient Adsorbent for Lysozyme

To meet the demand for the separation of specific substances, the construction of porous composite aerogels with a high specific surface area and a strong adsorption capacity is still a challenge. Herein, a sodium alginate/bentonite composite aerogel was efficiently prepared through supercritical fluid drying. The aerogel’s volume shrank less during supercritical drying, maintaining its original three-dimensional mesh structure. The resulting aerogel had a large specific surface area (445 m²/g), a low density (0.059 g/cm³), and a large pore volume (3.617 cm³/g). Due to the fixation and intercalation effects, bentonite was uniformly dispersed in the sodium alginate matrixes. The adsorption of lysozyme by the composite aerogel was evaluated, and the results showed that the optimal adsorption pH was 8 when the pH of the phosphoric acid buffer solution was between pH = 5 and 8.5. The time for adsorption to reach equilibrium was 8 h. The adsorption capacity increased with the increase in bentonite content, and when the initial concentration of lysozyme was from 0.2 to 1.2 g/L, the adsorption capacity first increased and then stabilized, and the maximum adsorption amount was 697 mg/g. The adsorption behavior was simulated in the isothermal region, and the linear correlation coefficient of Langmuir isothermal adsorption fitting was found to be 0.997. Thus, this composite aerogel with strong adsorption capacity can be used as a good alternative to enzymatic adsorbents or immobilized materials.

Tuning the properties of porous chitosan: Aerogels and cryogels

Highly porous chitosan-based materials were prepared via dissolution, non-solvent induced phase separation and drying using different methods. The goal was to tune the morphology and properties of chitosan porous materials by varying process parameters. Chitosan concentration, concentration of sodium hydroxide in the coagulation bath and aging time were varied. Drying was performed via freeze-drying leading to "cryogels" or via drying with supercritical CO₂ leading to "aerogels". Cryogels were of lower density than aerogels (0.03-0.12 g/cm³vs 0.07-0.26 g/cm³, respectively) and had a lower specific surface area (50-70 vs 200-270 m²/g, respectively). The absorption of simulated wound exudate by chitosan aerogels and cryogels was studied in view of their potential applications as wound dressing. Higher absorption was obtained for cryogels (530-1500%) as compared to aerogels (200-610%).

Polylactide-Grafted Metal-Alginate Aerogels

Τhis work describes the synthesis of PLA-grafted M-alginate (g-M-alginate; M: Ca²⁺, Co²⁺, Ni²⁺, Cu²⁺) aerogels. DL-lactide (LA) was attached on the surface of preformed M-alginate beads and was polymerized, using stannous octoate as catalyst and the –OH groups of the alginate backbone as initiators/points of attachment. The material properties of g-M-alginate aerogels were not affected much by grafting, because the linear PLA chains grew on the M-alginate framework like a brush and did not bridge their points of attachment as in polyurea-crosslinked M-alginate aerogels. Thus, all g-M-alginate aerogels retained the fibrous morphology of their parent M-alginate aerogels, and they were lightweight (bulk densities up to 0.24 g cm⁻³), macroporous/mesoporous materials with high porosities (up to 96% v/v). The BET surface areas were in the range of 154–542 m² g⁻¹, depending on the metal, the nature of the alginate framework and the PLA content. The latter was found at about 15% w/w for Ca- and Ni-based materials and at about 29% w/w for Co- and Cu-based materials. Overall, we have demonstrated a new methodology for the functionalization of alginate aerogels that opens the way to the synthesis of polylactide-crosslinked alginate aerogels with the use of multifunctional monomers.

Comparison of green bio-based cerium/alginate vs. copper/alginate beads: a study of vibrational and thermal properties using experimental and theoretical methods

Herein, bio-based alginates (Alg) containing metallic beads (Ce and Cu) were synthesized via an alginate cross-linking method, and their properties were studied using experimental techniques combined with theoretical simulations. Materials were characterized through Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and scanning electron microscope (SEM) images, to determine the cross-linking structural features, thermal stability, and surface morphology of alginates. Besides, density functional theory (DFT) methods were employed to calculate global reactivity parameters such as HOMO-LUMO gap energies (ΔE_H-L), electronegativity (χ), hardness (η), and electrophilic and nucleophilic indicators, using both gas and aqueous media for the study of the complexation process. Among other features, characterization of the thermal properties showed that Alg@Ce and Alg@Cu alginate beads behave differently as a function of the temperature. This behavior was also predicted by the conformation energy differences between Alg@Ce and Alg@Cu, which were found out theoretically and explained with the combined study of the vibrational modes between the carboxylate group with either Ce or Cu. Overall, the reactivity of the Alg@Ce alginate bead was higher than that of the Alg@Cu counterpart, results could be used as a cornerstone to employed the materials here studied in a wide range of applications.

Elastic and Dynamic Heterogeneity in Aging Alginate Gels

Anomalous aging in soft glassy materials has generated a great deal of interest because of some intriguing features of the underlying relaxation process, including the emergence of "ultra-long-range" dynamical correlations. An intriguing possibility is that such a huge correlation length is reflected in detectable ensemble fluctuations of the macroscopic material properties. We tackle this issue by performing replicated mechanical and dynamic light scattering (DLS) experiments on alginate gels, which recently emerged as a good model-system of anomalous aging. Here we show that some of the monitored quantities display wide variability, including large fluctuations in the stress relaxation and the occasional presence of two-step decay in the DLS decorrelation functions. By quantifying elastic fluctuation through the standard deviation of the elastic modulus and dynamic heterogeneities through the dynamic susceptibility, we find that both quantities do increase with the gel age over a comparable range. Our results suggest that large elastic fluctuations are closely related to ultra-long-range dynamical correlation, and therefore may be a general feature of anomalous aging in gels.

Colloidal structure and proton conductivity of the gel within the electrosensory organs of cartilaginous fishes

Cartilaginous fishes possess gel-filled tubular sensory organs called Ampullae of Lorenzini (AoL) that are used to detect electric fields. Although recent studies have identified various components of AoL gel, it has remained unclear how the molecules are structurally arranged and how their structure influences the function of the organs. Here we describe the structure of AoL gel by microscopy and small-angle X-ray scattering and infer that the material is colloidal in nature. To assess the relative function of the gel's protein constituents, we compared the microscopic structure, X-ray scattering, and proton conductivity properties of the gel before and after enzymatic digestion with a protease. We discovered that while proteins were largely responsible for conferring the viscous nature of the gel, their removal did not diminish proton conductivity. The findings lay the groundwork for more detailed studies into the specific interactions of molecules inside AoL gel at the nanoscale.

Extrusion-Based 3D Printing for Highly Porous Alginate Materials Production

Three-dimensional (3D) printing is a promising technology for solving a wide range of problems: regenerative medicine, tissue engineering, chemistry, etc. One of the potential applications of additive technologies is the production of highly porous structures with complex geometries, while printing is carried out using gel-like materials. However, the implementation of precise gel printing is a difficult task due to the high requirements for “ink”. In this paper, we propose the use of gel-like materials based on sodium alginate as “ink” for the implementation of the developed technology of extrusion-based 3D printing. Rheological studies were carried out for the developed alginate ink compositions. The optimal rheological properties are gel-like materials based on 2 wt% sodium alginate and 0.2 wt% calcium chloride. The 3D-printed structures with complex geometry were successfully dried using supercritical drying. The resulting aerogels have a high specific surface area (from 350 to 422 m²/g) and a high pore volume (from 3 to 3.78 cm³/g).

A comprehensive survey upon diverse and prolific applications of chitosan-based catalytic systems in one-pot multi-component synthesis of heterocyclic rings

Heterocyclic compounds are among the most prestigious and valuable chemical molecules with diverse and magnificent applications in various sciences. Due to the remarkable and numerous properties of the heterocyclic frameworks, the development of efficient and convenient synthetic methods for the preparation of such outstanding compounds is of great importance. Undoubtedly, catalysis has a conspicuous role in modern chemical synthesis and green chemistry. Therefore, when designing a chemical reaction, choosing and or preparing powerful and environmentally benign simple catalysts or complicated catalytic systems for an acceleration of the chemical reaction is a pivotal part of work for synthetic chemists. Chitosan, as a biocompatible and biodegradable pseudo-natural polysaccharide is one of the excellent choices for the preparation of suitable catalytic systems due to its unique properties. In this review paper, every effort has been made to cover all research articles in the field of one-pot synthesis of heterocyclic frameworks in the presence of chitosan-based catalytic systems, which were published roughly by the first quarter of 2020. It is hoped that this review paper can be a little help to synthetic scientists, methodologists, and catalyst designers, both on the laboratory and industrial scales.

Mesoporous Biopolymer Architecture Enhanced the Adsorption and Selectivity of Aqueous Heavy-Metal Ions

Halloysite nanotubes (HNT) and ball-milled biochar (BC) incorporated biocompatible mesoporous adsorbents (HNT-BC@Alg) were synthesized for adsorption of aqueous heavy-metal ions. HNT-BC@Alg outperformed the BC, HNT, and BC@Alg in removing cadmium (Cd), copper (Cu), nickel (Ni), and lead (Pb). Mesoporous structure (∼7.19 to 7.56 nm) of HNT-BC@Alg was developed containing an abundance of functional groups induced from encapsulated BC and tubular HNT, which allowed heavy metals to infiltrate and interact with the adsorbents. Siloxane groups from HNT, oxygen-containing functional groups from BC, and hydroxyl and carboxyl groups from alginate polymer play a significant role in the adsorption of heavy-metal ions. The removal percentage of heavy metals was recorded as Pb (∼99.97 to 99.05%) > Cu (∼95.01 to 90.53%) > Cd (∼92.5 to 55.25%) > Ni (∼80.85 to 50.6%), even in the presence of 0.01/0.001 M of CaCl₂ and Na₂SO₄ as background electrolytes and charged organic molecule under an environmentally relevant concentration (200 μg/L). The maximum adsorption capacities of Ni, Cd, Cu, and Pb were calculated as 2.85 ± 0.08, 6.96 ± 0.31, 16.87 ± 1.50, and 26.49 ± 2.04 mg/g, respectively. HNT-BC@Alg has fast sorption kinetics and maximum adsorption capacity within a short contact time (∼2 h). Energy-dispersive X-ray spectroscopy (EDS) elemental mapping exhibited that adsorbed heavy metals co-distributed with Ca, Si, and Al. The reduction of surface area, pore volume, and pore area of HNT-BC@Alg (after sorption of heavy metals) confirms that mesoporous surface (2-18 nm) supports diffusion, infiltration, and interaction. However, a lower range of mesoporous diameter of the adsorbent is more suitable for the adsorption of heavy-metal ions. The adsorption isotherm and kinetics fitted well with the Langmuir isotherm and the pseudo-second-order kinetic models, demonstrating the monolayer formation of heavy-metal ions through both the physical sorption and chemical sorption, including pore filling, ion exchange, and electrostatic interaction.

Tuning bio-aerogel properties for controlling theophylline delivery. Part 1: Pectin aerogels

A comprehensive study of release kinetics of a hydrophilic drug from bio-aerogels based on pectin was performed. Pectin aerogels were made by polymer dissolution, gelation (in some cases this step was omitted), solvent exchange and drying with supercritical CO₂. Theophylline was loaded and its release was studied in the simulated gastric fluid during 1 h followed by the release in the simulated intestinal fluid. Pectin concentration, initial solution pH and concentration of calcium were varied to tune the properties of aerogel. The kinetics of theophylline release was monitored and correlated with aerogel density, specific surface area, and aerogel swelling and erosion. Various kinetic models were tested to identify the main physical mechanisms governing the release.

Characterization of potential probiotic strain, L. reuteri B2, and its microencapsulation using alginate-based biopolymers

In this study, Lactobacillus reuteri B2 was isolated from the feces of C57BL/6 mice and assessed on probiotic activity. L. reuteri B2 was identified by 16S rDNA sequencing, which the cell viability in acidic conditions at pH 2.0 was 64% after 2 h, and in the presents of 0.30% of the bile salts, after 6 h, was 37%. Antimicrobial assay with L. reuteri B2 showed maximum diameters against Klebsiela oxytoca J7 (12.5 ± 0.71 mm). We further hypothesized if L. reuteri B2 strain in the free form can survive all conditions in the gastrointestinal tract (GIT) then the utilization of the appropriate biomaterials would ameliorate its stability and viability in GIT. L. reuteri B2 was microencapsulated into sodium alginate-(Na-alg) and different content of Na-alg and sodium maleate (SM) beads. Characterization materials enveloped their thermal characteristics (TGA/DTA analysis) and structure using: scanning electron microscopy (SEM), FTIR, and particle size distribution. The high survival rate of L. reuteri B2 at low pH from 2.0 to 4.0 and in the presence of the bile salts, at concentrations up to 0.30%, was obtained. L. reuteri B2 showed strong antimicrobial activity and the best protection microencapsulated with Na-alg + SM in simulated gastric juices (SGJ).

Applications of chitosan in environmental remediation: A review

Environmental biotechnology is the use of biotechnology to develop and regulate biological systems for the remediation of environmental contamination. Nature has gifted ample material for remediation of its resources, among which chitosan is one of the most important and largely available biomaterial globally. Chitosan is a biopolymer obtained by deacetylation of chitin extracted from marine waste and its applications from drug delivery to food additives are broadly available. Chitosan exhibit several properties such as availability, low cost, high biocompatibility, and biodegradability. These properties make it biologically and chemically acceptable for use in various fields. Due to some limitations of pure chitosan, there has been a growing interest in modifying the chitosan in order to improve the original properties and widen the applications of pure phase chitosan. Various modified forms of chitosan and their associated applications are reviewed here with emphasis on their use in environmental remediation. The demand of chitosan in the global industrial market is growing which is briefly explained in this paper. Chitosan is used for water purification since a long time and still progress is going on for making it more efficient in the removal process. It can be used as a flocculent and coagulant, as an adsorbent for removing the contaminants like heavy metals, dyes, pesticides, antibiotics, biological contaminants from wastewater. Soil remediation using chitosan material is explained in this review. Various other applications such as drug delivery, food additives, tissue engineering are thoroughly reviewed.

False Morphology of Aerogels Caused by Gold Coating for SEM Imaging

The imaging of non-conducting materials by scanning electron microscopy (SEM) is most often performed after depositing few nanometers thick conductive layers on the samples. It is shown in this work, that even a 5 nm thick sputtered gold layer can dramatically alter the morphology and the surface structure of many different types of aerogels. Silica, polyimide, polyamide, calcium-alginate and cellulose aerogels were imaged in their pristine forms and after gold sputtering utilizing low voltage scanning electron microscopy (LVSEM) in order to reduce charging effects. The morphological features seen in the SEM images of the pristine samples are in excellent agreement with the structural parameters of the aerogels measured by nitrogen adsorption-desorption porosimetry. In contrast, the morphologies of the sputter coated samples are significantly distorted and feature nanostructured gold. These findings point out that extra care should be taken in order to ensure that gold sputtering does not cause morphological artifacts. Otherwise, the application of low voltage scanning electron microscopy even yields high resolution images of pristine non-conducting aerogels.

Mechanism of Hydration and Hydration Induced Structural Changes of Calcium Alginate Aerogel

The most relevant properties of polysaccharide aerogels in practical applications are determined by their microstructures. Hydration has a dominant role in altering the microstructures of these hydrophilic porous materials. To understand the hydration induced structural changes of monolithic Ca-alginate aerogel, produced by drying fully cross-linked gels with supercritical CO₂, the aerogel was gradually hydrated and characterized at different states of hydration by small-angle neutron scattering (SANS), liquid-state nuclear magnetic resonance (NMR) spectroscopy, and magic angle spinning (MAS) NMR spectroscopy. First, the incorporation of structural water and the formation of an extensive hydration sphere mobilize the Ca-alginate macromolecules and induce the rearrangement of the dry-state tertiary and quaternary structures. The primary fibrils of the original aerogel backbone form hydrated fibers and fascicles, resulting in the significant increase of pore size, the smoothing of the nanostructured surface, and the increase of the fractal dimension of the matrix. Because of the formation of these new superstructures in the hydrated backbone, the stiffness and the compressive strength of the aerogel significantly increase compared to its dry-state properties. Further elevation of the water content of the aerogel results in a critical hydration state. The Ca-alginate fibers of the backbone disintegrate into well-hydrated chains, which eventually form a quasi-homogeneous hydrogel-like network. Consequently, the porous structure collapses and the well-defined solid backbone ceases to exist. Even in this hydrogel-like state, the macroscopic integrity of the Ca-alginate monolith is intact. The postulated mechanism accounts for the modification of the macroscopic properties of Ca-alginate aerogel in relation to both humid and aqueous environments.

Preparation of aerogel beads and microspheres based on chitosan and cellulose for drug delivery: A review

Spherical aerogels are not easily broken during use and are easier to transport and store which can be used as templates for drug delivery. This review summarizes the possible approaches for the preparation of aerogel beads and microspheres based on chitosan and cellulose, an overview to the methods of manufacturing droplets is presented, afterwards, the transition mechanisms from sol to a spherical gel are reviewed in detail followed by different drying processes to obtain spherical aerogels with porous structures. Additionally, a specific focus is given to aerogel beads and microspheres to be regarded as drug delivery carriers. Furthermore, a core/shell architecture of aerogel beads and microspheres for controlled drug release is described and subjected to inspire readers to create novel drug release system. Finally, the conclusions and outlooks of aerogel beads and microspheres for drug delivery are summarized.

Nanoporous Crystalline Composite Aerogels with Reduced Graphene Oxide

High-porosity monolithic composite aerogels of syndiotactic polystyrene (sPS) and poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) containing reduced graphene oxide (r-GO) were prepared and characterized. The composite aerogels obtained by supercritical carbon dioxide (scCO₂) extraction of sPS/r-GO and PPO/r-GO gels were characterized by a fibrillar morphology, which ensured good handling properties. The polymer nanoporous crystalline phases obtained within the aerogels led to high surface areas with values up to 440 m² g⁻¹. The role of r-GO in aerogels was studied in terms of catalytic activity by exploring the oxidation capacity of composite PPO and sPS aerogels toward benzyl alcohol in diluted aqueous solutions. The results showed that, unlike sPS/r-GO aerogels, PPO/r-GO aerogels were capable of absorbing benzyl alcohol from the diluted solutions, and that oxidation of c.a. 50% of the sorbed benzyl alcohol molecules into benzoic acid occurred.

Fabrication of nanostructured mesoporous starch encapsulating soy-derived phytoestrogen (genistein) by well-tuned solvent exchange method

The present research was concerned with preparation of mesoporous starch (MPS) as a carrier for genistein, a model of poorly water-soluble phytoestrogen isoflavone; and exploration of the impact of different fabrication parameters on structural and loading properties. MPS is considered as a highly porous biomaterial which typically possesses nanometer-sized porous microstructure and low density, providing a large effective specific surface area (SSA) and hydrophilic surface to improve solubility, stability and bioavailability of poorly water-soluble active agents. To fabricate MPS, various concentrations (8-14% w/v) of starch from different sources (corn, potato and tapioca) was used for gel formation and the successive solvent exchange process was performed with use of various ethanol concentrations (40-70% v/v), which were then dried by different techniques (rotary vacuum evaporation, microwave and freeze drying). MPS quality attributes such as SSA, total porous volume, BJH pore diameter and swelling ratio were determined and effects of the fabrication parameters were investigated using L9-Taguchi orthogonal array design. The results indicate that second order polynomial regression models were well fitted for all response variables. Interestingly, the starch components greatly influenced physical properties of MPS. Also, the drying type and ethanol concentration altered significantly the model equations. The overall best fabrication condition (14% corn starch, 100% ethanol concentration in aging step and rotary vacuum drying) resulted in favorable MPS preparation with mean size of 105.4 nm and unimodal distribution. In the next step, genistein was encapsulated in MPS microstructure at different ratios, resulting in high loading capacity and efficiency (44.71% and 79.9%, respectively) at 1:1 weight ratio. Equilibrium adsorption isotherm of genistein was evaluated also by four different kinetics models including Langmuir, Freundlich, Dubinin-Radushkevich, and Temkin isotherms. The experimental data were found to be fitted well to the Langmuir model (R2 = 0.989). According to the electron microscopy and XRD analysis, the degree of genistein crystallinity lowered remarkably after the impregnation in to MPS, indicating improved solubility. In-vitro release profile of genistein from MPS in the simulated gastrointestinal buffer solutions (pH 1.2 and 6.8) demonstrated that incorporating genistein into the MPS enhanced the dissolution rate compared with genistein powder. Release kinetic data were fitted to the Higuchi model (R2 = 0.98), indicating diffusion-controlled release mechanism. Altogether, well-tuned MPS fabrication method can be utilized for an efficient encapsulation and dissolution enhancement of poorly soluble phytochemicals, such as genistein.

Transparent, Aldehyde-Free Chitosan Aerogel

Aldehyde-free, transparent chitosan aerogel is reported. The aerogel was prepared by thermal decomposition of urea to induce gelation of a chitosan solution, followed by solvent exchange to ethanol, and supercritical drying. Low urea concentrations (≤ 25 g L^-1) result in transparent and highly mesoporous aerogels, while higher urea concentrations (≥ 30 g L^-1) produce opaque, more macroporous aerogels. The high surface areas of > 400 m² g^-1, large mesopore volumes up to 3.5 cm³ g^-1, and optical transparency of the low-urea aerogels indicate a high structural homogeneity at the mesoscale, and the properties comparable to previously reported transparent chitosan aerogels prepared with formaldehyde crosslinking. The macroscopic size changes of the wet gels indicate that microstructure formation is controlled by the timing of chitosan coagulation, which depends among others on urea concentration. The aldehyde-free, microstructure-tunable process provides a new series of transparent biopolymer aerogels with "true aerogel" mesoporous structures.

Strong, Machinable, and Insulating Chitosan-Urea Aerogels: Toward Ambient Pressure Drying of Biopolymer Aerogel Monoliths

Biopolymer aerogels are an emerging class of materials with potential applications in drug delivery, thermal insulation, separation, and filtration. Chitosan is of particular interest as a sustainable, biocompatible, and abundant raw material. Here, we present urea-modified chitosan aerogels with a high surface area and excellent thermal and mechanical properties. The irreversible gelation of an acidic chitosan solution is triggered by the thermal decomposition of urea at 80 °C through an increase in pH and, more importantly, the formation of abundant ureido terminal groups. The hydrogels are dried using either supercritical CO₂ drying (SCD) or ambient pressure drying (APD) methods to elucidate the influence of the drying process on the final aerogel properties. The hydrogels are exchanged into ethanol prior to SCD, and into ethanol and then heptane prior to APD. The surface chemistry and microstructure are monitored by solid-state NMR and Fourier transform infrared spectroscopy, scanning electron microscopy, and nitrogen sorption. Surprisingly, large monolithic aerogel plates (70 × 70 mm²) can be produced by APD, albeit at a somewhat higher density (0.17-0.42 g/cm³). The as prepared aerogels have thermal conductivities of ∼24 and ∼31 mW/(m·K) and surface areas of 160-170 and 85-230 m²/g, for SCD and APD, respectively. For a primarily biopolymer-based material, these aerogels are exceptionally stable at elevated temperature (TGA) and char and self-extinguish after direct flame exposure. The urea-modified chitosan aerogels display superior mechanical properties compared to traditional silica aerogels, with no brittle rupture up to at least 80% strain, and depending on the chitosan concentration, relatively high E-moduli (1.0-11.6 MPa), and stress at 80% strain values (σ₈₀ of 3.5-17.9 MPa). Remarkably, the aerogel monoliths can be shaped and machined with standard tools, for example, drilling and sawing. This first demonstration to produce monolithic and machinable, mesoporous aerogels from bio-sourced, renewable, and nontoxic precursors, combined with the potential for reduced production cost by means of simple APD, opens up new opportunities for biopolymer aerogel applications and marks an important step toward commercialization of biopolymer aerogels.

Novel alginate-chitosan aerogel fibres for potential wound healing applications

Aerogels produced from marine polymers, such as chitosan and alginate, are of interest for wound healing applications due to their attractive properties. These properties can be the aerogel's high porosity along with the antimicrobial activity of chitosan or the capacity to provide a moist environment of alginate. The aim of this work was to develop a new route towards hybrid alginate-chitosan aerogel fibres and to evaluate their potential for wound healing applications. The influence of chitosan molecular weight and its content on the fibres characteristics was evaluated. To produce the fibres, the formation of polyelectrolyte complex hydrogels of both polymers was performed by the emulsion-gelation method. Hydrogels were converted in alcogels through a solvent exchange followed by drying with supercritical CO₂. Resulting aerogels were observed to be light-weight, fluffy mesoporous fibres with a specific surface area of 162-302 m²/g and specific pore volume of 1.41-2.49 cm³/g. Biocompatibility of the fibres was evaluated, and the result showed that they were non-cytotoxic. Bioactivity of the fibres regarding the ability to close a wound on an in vitro scale and antibacterial activity were also evaluated. Aerogel fibres presented percentages of recovered scratch area of about 75%, higher than the untreated control (~50%) and a clear antibacterial activity against Staphylococcus aureus and Klebsiella pneumoniae. The obtained results suggest that these alginate-chitosan aerogel fibres could be good candidates for wound healing applications.

Supercritical carbon dioxide techniques for processing microbial exopolysaccharides used in biomedical applications

Microbial exopolysaccharides are polymers that show a great potential for biomedical applications, such as tissue engineering applications and drug delivery, due to their biocompatibility, biodegradability and their gelling properties. These polysaccharides are obtained from a microorganism culture with a relatively straightforward downstream process thanks to their extracellular character, and can be processed to obtain aerogels, fibers and micro- or nano-particles with conventional techniques. However, these techniques present several disadvantages in that they involve time-consuming processes and the use of toxic solvents. Supercritical carbon dioxide techniques can overcome these drawbacks, but their use for processing microbial exopolysaccharides is not extended in the scientific community. This review describes the most frequently used exopolysaccharides in biomedical applications and how they can be obtained, as well as the different supercritical carbon dioxide techniques that can be used for processing them and their challenges. Specifically, high pressure shows a great potential to process and sterilize exopolysaccharide biomaterials for biomedical applications (e.g. tissue engineering or drug delivery systems) in spite of the disadvantage concerning the hydrophilicity of this type of polymers.

Preparation and Characterization of Chitosan-Coated Pectin Aerogels: Curcumin Case Study

The following study describes the preparation of pectin aerogels and pectin aerogels coated with an external layer of chitosan. For the preparation of chitosan-coated pectin aerogels, a modified coating procedure was employed. Since pectin as well as pectin aerogels are highly water soluble, a function of chitosan coating is to slow down the dissolution of pectin and consequently the release of the active substances. Textural properties, surface morphologies, thermal properties, and functional groups of prepared aerogels were determined. Results indicated that the coating procedure affected the textural properties of pectin aerogels, resulting in smaller specific surface areas of 276 m²/g, compared to 441 m²/g. However, chitosan-coated pectin aerogels still retained favorable properties for carriers of active substances. The case study for prepared aerogels was conducted with curcumin. Prior to in-vitro release studies, swelling studies were performed. Curcumin’s dissolution from both aerogels showed to be successful. Pectin aerogels released curcumin in 3 h showing a burst release profile. Chitosan-coated pectin aerogels prolonged curcumin release up to 24 h, thus showing a controlled release profile.