Recent developments in the selective dispersion of single-walled carbon nanotubes using conjugated polymers

Performance Enhancement of Carbon Nanotube Network Transistors via SbI3 Inner-Doping in Selected Regions

Semiconducting single-wall carbon nanotubes (s-SWCNTs) represent one of the most promising materials for surpassing Moore's Law and developing the next generation of electronic devices. Despite numerous developed approaches, reducing the contact resistance of s-SWCNTs networks remains a significant challenge in achieving further enhancements in electronic performance. In this study, antimony triiodide (SbI3) is efficiently encapsulated within high-purity s-SWCNTs films at low temperatures, forming 1D SbI3@s-SWCNTs vdW heterostructures. The semiconductor-metal transition of individual SbI3@s-SWCNTs is characterized via sensitive dielectric force microscopy, with the results confirmed through electrical device tests. The electrical behavior transition is attributed to an interlayer charge transfer, as demonstrated by Kelvin probe force microscopy. Moreover, the electrical performance of s-SWCNTs thin-film transistors improves significantly with SbI3@s-SWCNTs networks as contact electrodes. This process reduces the contact resistance between the s-SWCNTs channel and the electrodes, enhancing electrical performance. Specifically, the contact resistance decreases to one-third of the original, the carrier mobility increases by ≈10 times, the on-off ratio exceeds 106, and the subthreshold swing reduces significantly to ≈65 mV dec-1. These results demonstrate the effectiveness of inner-doping-induced metallization of s-SWCNTs in the contact region, essential for advancing carbon nanotube electronic devices and circuits.

Efficient Sorting of Semiconducting Single-Walled Carbon Nanotubes in Bio-Renewable Solvents Through Main-Chain Engineering of Conjugated Polymers

Conjugated polymer sorting is recognized as an efficient and scalable method for the selective extraction of semiconducting single-walled carbon nanotubes (s-SWCNTs). However, this process typically requires the use of nonpolar and aromatic solvents as the dispersion medium, which are petroleum-based and carry significant production hazards. Moreover, there is still potential for improving the efficiency of batch purification. Here, this study presents fluorene-based conjugated polymer that integrates diamines containing ethylene glycol chains (ODA) as linkers within the main chain, to effectively extract s-SWCNTs in bio-renewable solvents. The introduction of ODA segments enhances the solubility in bio-renewable solvents, facilitating effective wrapping of s-SWCNTs in polar environments. Additionally, the ODA within the main chain enhances affinity to s-SWCNTs, thereby contributing to increased yields and purity. The polymer achieves a high sorting yield of 55% and a purity of 99.6% in dispersion of s-SWCNTs in 2-Methyltetrahydrofuran. Thin-film transistor arrays fabricated with sorted s-SWCNTs solution through slot-die coating exhibit average charge carrier mobilities of 20-23 cm2 V⁻¹ s⁻¹ and high on/off current ratios exceeding 105 together with high spatial uniformity. This study highlights the viability of bio-renewable solvents in the sorting process, paving the way for the eco-friendly approach to the purification of SWCNTs.

CO2 Responsive Thin-Film Transistors Using Conjugated Polymer Complexes with Single-Walled Carbon Nanotubes

Introduction of amidine groups within the side chains of a conjugated polyfluorene was carried out using copper-catalyzed azide-alkyne cycloaddition. The resulting polymer was shown to form strong supramolecular interactions with the sidewalls of single-walled carbon nanotubes (SWNTs), forming polymer-nanotube complexes that exhibited solubility in various organic solvents. It was shown that the polymer-SWNT complexes were responsive to CO2, where the amidine groups formed amidinium bicarbonate salts upon CO2 exposure, causing the polymer-SWNT complexes to precipitate. This reaction could be reversed by bubbling N2 through the solution, which caused the polymer-SWNT complexes to redissolve. Incorporation of the polymer-SWNT complexes within thin-film transistor (TFT) devices as the active layer resulted in a CO2-responsive TFT sensor. It was found that the sensory device underwent a reversible shift in its threshold voltage from 5 to -1 V as well as a 1 order of magnitude decrease in its on-current upon exposure to CO2. This work shows that conjugated polymer-wrapped SWNTs having sensory elements within the polymer side chain can be used as the active layer within functional SWNT-based TFT sensors.

Size Matters in Conjugated Polymer Chirality-Selective SWCNT Extraction

Carbon-based nanomaterials have catalyzed breakthroughs across various scientific and engineering disciplines. The key to unlocking a new generation of tailor-made nanomaterials based on single-walled carbon nanotubes (SWCNTs) lies in the precise sorting of raw material into individual chiralities, each possessing unique properties. This can be achieved using conjugated polymer extraction (CPE), but to a very limited extent since the process generates only a few chirality-enriched suspensions. Therefore, it is imperative to comprehend the mechanism of the wrapping of SWCNTs by polymers to unleash CPE's full potential. However, the lack of a diverse palette of chirality-selective polymers with varying macromolecular parameters has hindered a comprehensive understanding of how the nature of the polymer affects the performance and selectivity of SWCNT isolation. To address this gap, multiple batches of such polymers are synthesized to elucidate the impact of molecular weight and dispersity on the purity and concentrations of the generated SWCNT suspensions. The obtained results explain the inconsistent outcomes reported in the literature, greatly improving the application potential of this promising SWCNT sorting approach. Concomitantly, the discovered significant influence of the macromolecular characteristics of conjugated polymers on the SWCNT isolation efficacy sheds considerable insight into the unresolved mechanism of this sorting technique.

Conjugated Polymers with Self-Immolative Sidechain Linkers for Carbon Nanotube Dispersion

Single-walled carbon nanotubes (SWNTs) are promising materials for generating high-performance electronic devices. However, these applications are greatly restricted by their lack of purity and solubility. Commercially available SWNTs are a mixture of semi-conducting (sc-) and metallic (m-) SWNTs and are insoluble in common solvents. Conjugated polymers can selectively disperse either sc- or m-SWNTs and increase their solubility; however, the conductivity of conjugated polymer-wrapped SWNTs is largely affected by the polymer side chains. Here, a poly(fluorene-co-phenylene) polymer that contains a self-immolative linker as part of its sidechains is reported. The self-immolative linker is stabilized with a tert-butyldimethylsilyl ether group that, upon treatment with tetra-n-butylammonium fluoride (TBAF), undergoes a 1,6-elimination reaction to release the sidechain. Sonication of this polymer with SWNTs in tetrahydrofuran (THF) results in concentrated dispersions that are used to prepare polymer-SWNT thin films. Treatment with TBAF caused side-chain cleavage into carbon dioxide and the corresponding diol, which can be easily removed by washing with solvent. This process is characterized by a combination of absorption and Raman spectroscopy, as well as four-point probe measurements. The conductance of the SWNT thin films increased ≈60-fold upon simple TBAF treatment, opening new possibilities for producing high-conductivity SWNT materials for numerous applications.

PdNPs/NiNWs as a welding tool for the synthesis of polyfluorene derivatives by Suzuki polycondensation under microwave radiation

Conjugated polymers are promising tools to differentiate various types of semiconducting single-walled carbon nanotubes (s-SWCNTs). However, their synthesis is challenging. Insufficient control over molecular weights, and unpredictive/unrepeatable batches hinder possible applications and scale-up. Furthermore, commercial homogeneous catalysts often require inert conditions and are almost impossible to recycle. To overcome these problems, we present a nanocatalyst consisting of magnetic nickel nanowires decorated with highly active palladium nanoparticles. A two-step wet chemical reduction protocol with the assistance of sonochemistry was employed to obtain a heterogeneous catalyst capable of conducting step-growth Suzuki polycondensation of a fluorene-based monomer. Additionally, we enhanced the performance of our catalytic system via controlled microwave irradiation, which significantly shortened the reaction time from 3 d to only 1 h. We studied the influence of the main process parameters on the yield and polymer chain length to gain insight into phenomena occurring in the presence of metallic species under microwave irradiation. Finally, the produced polymers were used to extract specific s-SWCNTs by conjugated polymer extraction to validate their utility.

Functionalized carbon nanotube field-effect transistor biosensor for highly sensitive detection of exosomal protein

Since the exosomal protein level is related to many diseases, sensitive detection of exosomal protein is highly desirable. Here, we describe a polymer-sorted high-purity semiconducting carbon nanotubes (CNTs) films-based field-effect transistor (FET) biosensor for ultrasensitive and label-free detection of MUC1, a transmembrane protein highly expressed in breast cancer exosomes. Polymer-sorted semiconducting CNTs hold advantages including high purity (>99%), high CNT concentration, and short processing time (<1 h), but they are difficult to be stably functionalized with biomolecules because of lacking hanging bonds on their surface. To solve this issue, poly-lysine (PLL) was employed to modify the CNT films after they were deposited on the sensing channel surface of the fabricated FET chip. To specifically recognize the exosomal protein, sulfhydryl aptamer probes were immobilized on the gold nanoparticles (AuNPs) surface that was assembled on PLL substrate. The aptamer-modified CNT FET was capable of sensitively and selectively detecting exosomal MUC1 as high as 0.34 fg/mL. Moreover, the CNT FET biosensor was able to recognize breast cancer patients from healthy individuals by comparing the expression level of exosomal MUC1. The developed CNT FET biosensor is expected to be a novel assay for early diagnosis of cancer.

Decoration of Polyfluorene-Wrapped Carbon Nanotubes with Photocleavable Side-Chains

Functionalizing polyfluorene-wrapped carbon nanotubes without damaging their properties is effective via Copper-Catalyzed Azide-Alkyne Cycloaddition (CuAAC). However, the length and nature of polymer side-chains can impact the conductivity of polyfluorene-SWNT films by preventing close contact between the nanotubes. Here, we investigate the functionalization of a polyfluorene-SWNT complex using photocleavable side-chains that can be removed post-processing. The cleavage of the side-chains containing an ortho-nitrobenzyl ether derivative is efficient when exposed to a UV lamp at 365 nm. The photoisomerization of the o-nitrobenzyl ether linker into the corresponding o-nitrosobenzaldehyde was first monitored via UV-Vis absorption spectroscopy and 1H-NMR spectroscopy on the polymer, which showed efficient cleavage after 2 h. We next investigated the cleavage on the polyfluorene-SWNT complex via UV-Vis-NIR absorption spectroscopy. The precipitation of the nanotube dispersion and the broad absorption peaks after overnight irradiation also indicated effective cleavage. In addition, Raman spectroscopy post-irradiation showed that the nanotubes were not damaged upon irradiation. This paper reports a proof of concept that may find applications for SWNT-based materials in which side-chain removal could lead to higher device performance.

Efficient Selective Sorting of Semiconducting Carbon Nanotubes Using Ultra-Narrow-Band-Gap Polymers

Conjugated polymers with narrow band gaps are particularly useful for sorting and discriminating semiconducting single-walled carbon nanotubes (s-SWCNT) due to the low charge carrier injection barrier for transport. In this paper, we report two newly synthesized narrow-band-gap conjugated polymers (PNDITEG-TVT and PNDIC8TEG-TVT) based on naphthalene diimide (NDI) and thienylennevinylene (TVT) building blocks, decorated with different polar side chains that can be used for dispersing and discriminating s-SWCNT. Compared with the mid-band-gap conjugated polymer PNDITEG-AH, which is composed of naphthalene diimide (NDI) and head-to-head bithiophene building blocks, the addition of a vinylene linker eliminates the steric congestion present in head-to-head bithiophene, which promotes backbone planarity, extending the π-conjugation length and narrowing the band gap. Cyclic voltammetry (CV) and density functional theory (DFT) calculations suggest that inserting a vinylene group in a head-to-head bithiophene efficiently lifts the highest occupied molecular orbital (HOMO) level (-5.60 eV for PNDITEG-AH, -5.02 eV for PNDITEG-TVT, and -5.09 eV for PNDIC8TEG-TVT). All three polymers are able to select for s-SWCNT, as evidenced by the sharp transitions in the absorption spectra. Field-effect transistors (FETs) fabricated with the polymer:SWCNT inks display p-dominant properties, with higher hole mobilities when using the NDI-TVT polymers as compared with PNDITEG-AH (0.6 cm² V^-1 s^-1 for HiPCO:PNDITEG-AH, 1.5 cm² V^-1 s^-1 for HiPCO:PNDITEG-TVT, and 2.3 cm² V^-1 s^-1 for HiPCO:PNDIC8TEG-TVT). This improvement is due to the better alignment of the HOMO level of PNDITEG-TVT and PNDIC8TEG-TVT with that of the dominant SWCNT specie.

Recent Advances in Structure Separation of Single-Wall Carbon Nanotubes and Their Application in Optics, Electronics, and Optoelectronics

Structural control of single-wall carbon nanotubes (SWCNTs) with uniform properties is critical not only for their property modulation and functional design but also for applications in electronics, optics, and optoelectronics. To achieve this goal, various separation techniques have been developed in the past 20 years through which separation of high-purity semiconducting/metallic SWCNTs, single-chirality species, and even their enantiomers have been achieved. This progress has promoted the property modulation of SWCNTs and the development of SWCNT-based optoelectronic devices. Here, the recent advances in the structure separation of SWCNTs are reviewed, from metallic/semiconducting SWCNTs, to single-chirality species, and to enantiomers by several typical separation techniques and the application of the corresponding sorted SWCNTs. Based on the separation procedure, efficiency, and scalability, as well as, the separable SWCNT species, purity, and quantity, the advantages and disadvantages of various separation techniques are compared. Combined with the requirements of SWCNT application, the challenges, prospects, and development direction of structure separation are further discussed.

Selective separation of single-walled carbon nanotubes in aqueous solution by assembling redox nanoclusters

The selective separation of soluble and individual single-walled carbon nanotubes (SWCNTs) in aqueous solution is a key step for harnessing the extraordinary properties of these materials. Manipulating the strong van der Waals intertube interactions between the SWCNT bundles is very important in selective separation, which is a long-standing challenge. Here we reported the ability of redox polyoxometalate clusters to modulate the intertube π-π stacking interaction through electron transfer and achieved the diameter-selective separation of SWCNTs in a surfactant aqueous solution. The large-diameter SWCNTs concentrated at ∼1.3-1.4 nm were selectively separated when ∼1 nm clusters encapsulated within the tube cavity, and the dispersion of subnanometer ∼0.7-0.9 nm SWCNTs was boosted when clusters were adsorbed on the outer surface of small-diameter nanotubes. The mechanism of diameter-selective separation of SWCNTs associated with the size-dependent interaction between cluster-tubes and the steric hindrance effect of clusters was revealed by optical absorption and Raman spectroscopy. This simple method thus enables the selective separation of individual high-quality SWCNTs in aqueous solutions without harsh sonication with the potential for other separation applications.

Synthesis of a Poly(3-dodecylthiophene) Bearing Aniline Groups for the Covalent Functionalization of Carbon Nanotubes

The functionalization of carbon nanotubes by polymers necessitates two steps, first their modification by oxidizing them or by covalently attaching small compounds to them, then the growth of the polymer chains from these anchors or their grafting onto them. In order to better control the process and the rate of functionalization, we develop polymers able to covalently react with the carbon nanotubes by their side chains in one step. We describe the synthesis of a copolymer of dodecylthiophene and its analogue bearing an aniline group at the end of the dodecyl side chain. This copolymer can functionalize single-walled carbon nanotubes (SWNTs) non-covalently and disperse more SWNTs than its hexyl analogues. UV-Vis and fluorescence spectroscopies show that in these non-covalent hybrids, the polymer forms p-stacked aggregates on the SWNTs. The non-covalent hybrids can be transformed into covalent ones by diazonium coupling. In these covalent hybrids the polymer is no longer p-stacked. According to Raman spectroscopy, the conformation of the poly(3-hexylthiophene) backbone is more ordered in the non-covalent hybrids than in the covalent ones.

The Impacts of Polyisoprene Physical Interactions on Sorting of Single-Wall Carbon Nanotubes

Conjugated polymer sorting is currently the best method to select large-diameter single-walled carbon nanotubes (SWCNTs) with tunable narrow chirality in the adaption of highly desired electronics applications. The acceleration on conjugated polymers-SWCNTs interaction with long-term stability through different molecular designs; for example, longer alkyl side-chains or conjugation moieties have been extensively developed in recent years. However, the importance of the macromolecules with abundant van der Waals (VDW) interaction in the conjugated-based block copolymer system acting during SWCNTs sorting is not clearly demonstrated. In this work, a conjugated diblock copolymer involving polyisoprene (PI) and highly dense π-interaction of poly (9,9-dioctylfluorene) (PFO) is utilized to investigate the impact of natural rubber PI physical interaction on sorting effectiveness and stability. Through the rational design of diblock copolymer, PFO with ≈1200 isoprene units can remarkably enhance SWCNTs sorting ability and selected few chiralities with a diameter of ≈0.83-1.1 nm and highly stable solution for more than 1 year. The introduction of long-chain PI system is attributed not only to form weak VDW force with SWCNTs and strengthen the wrapping of PFO around the semiconducting SWCNTs but also to act as a barrier among nanotubes to prevent reaggregation of sorted SWCNTs.

A Spin-Coated Hydrogel Platform Enables Accurate Investigation of Immobilized Individual Single-Walled Carbon Nanotubes

Single-walled carbon nanotubes (SWCNTs) have been used in a variety of sensing and imaging applications over the past few years due to their unique optical properties. In the solution phase, SWCNTs are employed as near-infrared (NIR) fluorescence-based sensors of target analytes via modulations in emission intensity and/or wavelength. In an effort to lower the limit of detection, research has been conducted into isolating SWCNTs adhered to surfaces for potential single molecule analyte detection. However, it is known that SWCNT fluorescence is adversely affected by the inherently rough surfaces that are conventionally used for their observation (e.g., glass coverslip), potentially interfering with fluorescence-based analyte detection. Here, using a spin-coating method with thin films of alginate and SWCNTs, we demonstrate that a novel hydrogel platform can be created to investigate immobilized individual SWCNTs without significantly perturbing their optical properties as compared to solution-phase values. In contrast to the glass coverslip, which red-shifted DNA-functionalized (6,5)-SWCNTs by an average of 3.4 nm, the hydrogel platform reported emission wavelengths that statistically matched the solution-phase values. Additionally, the heterogeneity in the wavelength measurements, as determined from the width of created histograms, was reduced nearly by a factor of 3 for the SWCNTs in the hydrogel platform when compared to glass coverslips. Using long SWCNTs, i.e., those with an average length above the diffraction limit of our microscope, we show that a glass coverslip can induce optical heterogeneity along the length of a single SWCNT regardless of its surface functionalization. This is again significantly mitigated when examining the long SWCNTs in the hydrogel platform. Finally, we show that upon the addition of a model analyte (calcium chloride), the optical response can be spatially resolved along the length of a single SWCNT, enabling localized analyte detection on the surface of a single nanoscale sensor.

Host-Guest Molecular Interaction Enabled Separation of Large-Diameter Semiconducting Single-Walled Carbon Nanotubes

Semiconducting single-walled carbon nanotubes (s-SWCNTs) with a diameter of around 1.0-1.5 nm, which present bandgaps comparable to silicon, are highly desired for electronic applications. Therefore, the preparation of s-SWCNTs of such diameters has been attracting great attention. The inner surface of SWCNTs has a suitable curvature and large contacting area, which is attractive in host-guest chemistry triggered by electron transfer. Here we reported a strategy of host-guest molecular interaction between SWCNTs and inner clusters with designed size, thus selectively separating s-SWCNTs of expected diameters. When polyoxometalate clusters of ∼1 nm in size were filled in the inner cavities of SWCNTs, s-SWCNTs with diameters concentrated at ∼1.3-1.4 nm were selectively extracted with the purity of ∼98% by a commercially available polyfluorene derivative. The field-effect transistors built from the sorted s-SWCNTs showed a typical behavior of semiconductors. The sorting mechanisms associated with size-dependent electron transfer from nanotubes to inner polyoxometalate were revealed by the spectroscopic and in situ electron microscopic evidence as well as the theoretical calculation. The polyoxometalates with designable size and redox property enable the flexible regulation of interaction between the nanotubes and the clusters, thus tuning the diameter of sorted s-SWCNTs. The present sorting strategy is simple and should be generally feasible in other SWCNT sorting techniques, bringing both great easiness in dispersant design and improved selectivity.

Excess Polymer in Single-Walled Carbon Nanotube Thin-Film Transistors: Its Removal Prior to Fabrication Is Unnecessary

Ultrapure semiconducting single-walled carbon nanotube (sc-SWNT) dispersions produced through conjugated polymer sorting are ideal candidates for the fabrication of solution-processed organic electronic devices on a commercial scale. Protocols for sorting and dispersing ultrapure sc-SWNTs with conjugated polymers for thin-film transistor (TFT) applications have been well refined. Conventional wisdom dictates that removal of excess unbound polymer through filtration or centrifugation is necessary to produce high-performance TFTs. However, this is time-consuming, wasteful, and resource-intensive. In this report, we challenge this paradigm and demonstrate that excess unbound polymer during semiconductor film fabrication is not necessarily detrimental to device performance. Over 1200 TFT devices were fabricated from 30 unique polymer-sorted SWNT dispersions, prepared using two different alternating copolymers. Detailed Raman spectroscopy, x-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) studies of the random-network semiconductor films demonstrated that a simple solvent rinse during TFT fabrication was sufficient to remove unbound polymer from the sc-SWNT films, thus eliminating laborious polymer removal before TFT fabrication. Furthermore, below a threshold polymer concentration, the presence of excess polymer during fabrication did not significantly impede TFT performance. Preeminent performance was achieved for devices prepared from native polymer-sorted SWNT dispersions containing the "original" amount of excess unbound polymer (immediately following enrichment). Lastly, we developed an open-source Machine Learning algorithm to quantitatively analyze AFM images of SWNT films for surface coverage, number of tubes, and tube alignment.

Highly Aligned Array of Heterostructured Polyflourene-Isolated Boron Nitride and Carbon Nanotubes

Boron nitride nanotubes (BNNTs) have attracted increasing attention for their exceptional thermal, electronic, and optical properties. However, the progress in BNNTs applications has largely been limited by the low purity of as-synthesized BNNTs and inefficient solution-processing protocols due mainly to the instability of BNNTs in most of the solvents. Therefore, fabrication of highly pure, stable, and fully individualized BNNTs in a rational manner is required. Here, we report a significant improvement in the preparation of well-dispersed BNNTs, utilizing conjugated polymers that interact with BNNTs, allowing selective sorting and individualization of the nanotubes. Evidence of strong interactions between the polymers and BNNTs was observed by optical absorption and photoluminescence spectroscopies, while effective individualization was observed by electron microscopy. The sorted BNNTs were successfully used in a solution-processing protocol called dose-controlled, floating evaporative self-assembly (DFES) previously established for single-walled carbon nanotubes (SWCNT) array fabrication. A device fabricated via DFES from the sorted BNNTs mixed with polymer-wrapped, semiconducting single-walled carbon nanotubes (s-SWCNTs) exhibited an on-state conductance of 253 ± 6 μS μm^-1 and an on/off ratio of 10^6.6±0.4 for a gate voltage of -0.1 V. This breakthrough in BNNT dispersion and isolation is a significant advancement toward the exploitation of BNNTs in future applications.

Separation of Semiconducting Carbon Nanotubes Using Conjugated Polymer Wrapping

In the past two decades, single-walled carbon nanotubes (SWNTs) have been explored for electronic applications because of their high charge carrier mobility, low-temperature solution processability and mechanical flexibility. Semiconducting SWNTs (s-SWNTs) are also considered an alternative to traditional silicon-based semiconductors. However, large-scale, as-produced SWNTs have poor solubility, and they are mixtures of metallic SWNTs (m-SWNTs) and s-SWNTs, which limits their practical applications. Conjugated polymer wrapping is a promising method to disperse and separate s-SWNTs, due to its high selectivity, high separation yield and simplicity of operation. In this review, we summarize the recent progress of the conjugated polymer wrapping method, and discuss possible separation mechanisms for s-SWNTs. We also discuss various parameters that may affect the selectivity and sorting yield. Finally, some electronic applications of polymer-sorted s-SWNTs are introduced. The aim of this review is to provide polymer chemist a basic concept of polymer based SWNT separation, as well as some polymer design strategies, influential factors and potential applications.

Pentiptycene Polymer/Single-Walled Carbon Nanotube Complexes: Applications in Benzene, Toluene, and o-Xylene Detection

We report the dispersion of single-walled carbon nanotubes (SWCNTs) using pentiptycene polymers and their use in chemiresistance-based and QCM-D sensors. Poly(p-phenylene ethynylene)s (PPEs) incorporating pentiptycene moieties present a concave surface that promotes π-π interactions and van der Waals interactions with SWCNTs. In contrast to more common polymer-dispersing mechanisms that involve the wrapping of polymers around the SWCNTs, we conclude that the H-shape of pentiptycene groups and the linear rigid-rod structure creates a slot for nanotube binding. UV-vis-NIR, Raman, and fluorescence spectra and TEM images of polymer/SWCNTs support this dispersion model, which shows size selectivity to SWCNTs with diameters of 0.8-0.9 nm. Steric bulk on the channels is problematic, and tert-butylated pentiptycenes do not form stable dispersions with SWCNTs. This result, along with the diameter preference, supports the model in which the SWCNTs are bound to the concave clefts of the pentiptycenes. The binding model suggests that the polymer/SWCNTs complex creates galleries, and we have demonstrated the binding of benzene, toluene, and o-xylene (BTX) vapors as the basis for a robust, sensitive, and selective sensing platform for BTX detection. The utility of our sensors is demonstrated by the detection of benzene at the OSHA short-term exposure limit of 5 ppm in air.

Facile Fabrication of Semiconducting Single-Walled Carbon Nanotubes Patterns on Flexible Substrate Based on a Photoimmobilization Technique

Single-walled carbon nanotubes (SWCNTs) have attracted significant attention due to their outstanding properties. For their wide applications in electronics and optoelectronics, pure semiconducting SWCNTs (s-SWCNTs) and their precise placement are preconditions. Recent advances have focused on developing effective strategies to separate s-SWCNTs from raw SWCNTs, a mixture of metallic and semiconducting nanotubes, and deposit s-SWCNTs on target substrates. Herein, a polyfluorene-based alternative copolymer (PFBP) containing the benzophenone group was employed. PFBP achieved higher yield for s-SWCNTs than the well-studied poly(9,9-dioctylfluorene) through solution process. Subsequently, the dispersed s-SWCNTs were immobilized on a flexible polyethylene terephthalate in a facile manner by the photoreactive benzophenone group upon exposure to UV irradiation, and chemically robust patterns were fabricated from micro to macro scales through photomasks. Our method accomplished by utilizing photoimmobilization is a simple cleaning procedure and an important step forward in pitch scaling for further applications of conjugated polymer wrapped s-SWCNTs.

Chirality Pure Carbon Nanotubes: Growth, Sorting, and Characterization

Single-walled carbon nanotubes (SWCNTs) have been attracting tremendous attention owing to their structure (chirality) dependent outstanding properties, which endow them with great potential in a wide range of applications. The preparation of chirality-pure SWCNTs is not only a great scientific challenge but also a crucial requirement for many high-end applications. As such, research activities in this area over the last two decades have been very extensive. In this review, we summarize recent achievements and accumulated knowledge thus far and discuss future developments and remaining challenges from three aspects: controlled growth, postsynthesis sorting, and characterization techniques. In the growth part, we focus on the mechanism of chirality-controlled growth and catalyst design. In the sorting part, we organize and analyze existing literature based on sorting targets rather than methods. Since chirality assignment and quantification is essential in the study of selective preparation, we also include in the last part a comprehensive description and discussion of characterization techniques for SWCNTs. It is our view that even though progress made in this area is impressive, more efforts are still needed to develop both methodologies for preparing ultrapure (e.g., >99.99%) SWCNTs in large quantity and nondestructive fast characterization techniques with high spatial resolution for various nanotube samples.

Recent advances in dithiafulvenyl-functionalized organic conjugated materials

This review highlights the recent studies of advanced organic π-conjugated materials that contain 1,4-dithiafulvene (DTF) as a redox-active component.

Enrichment of highly pure large-diameter semiconducting SWCNTs by polyfluorene-containing pyrimidine ring

The use of copolymers to extract and purify semiconducting SWCNTs (sc-SWCNTs) and metallic SWCNTs (m-SWCNTs) is widely employed. In this paper, the performances of two pyrimidine-alt-dioctylfluorene conjugated polymers in the enrichment of semiconducting SWCNTs are compared, and the subtle structural effects on them are discussed. It was found that both pyrimidine-polymers were more effective in wrapping the semiconducting SWCNTs than the metallic SWCNTs under the co-action of the pyrimidine and fluorene rings. Moreover, methyl groups on the pyrimidine ring of the polymer slightly contributed to the semiconducting purity, and the minor differences of sc-SWCNTs extraction between two pyrimidine-polymers are compared. Additionally, the average diameter of the selected SWCNTs is larger than that of the raw SWCNTs. The experimental results show the excellent selectivity for sc-SWCNT from both co-polymers: the index Φ i values for determining the purity of sc-SWCNTs were increased from 0.408 for P2 to 0.465 for P1, of which the selected sc-SWCNT purity is up to 99.9%. The resulting purity and the inexpensive availability of pyrimidine co-polymers make them suitable to be considered for effective sc-SWCNT enrichment.

Solution-Processing of High-Purity Semiconducting Single-Walled Carbon Nanotubes for Electronics Devices

High-purity semiconducting single-walled carbon nanotubes (s-SWCNTs) are of paramount significance for the construction of next-generation electronics. Until now, a number of elaborate sorting and purification techniques for s-SWCNTs have been developed, among which solution-based sorting methods show unique merits in the scale production, high purity, and large-area film formation. Here, the recent progress in the solution processing of s-SWCNTs and their application in electronic devices is systematically reviewed. First, the solution-based sorting and purification of s-SWCNTs are described, and particular attention is paid to the recent advance in the conjugated polymer-based sorting strategy. Subsequently, the solution-based deposition and morphology control of a s-SWCNT thin film on a surface are introduced, which focus on the strategies for network formation and alignment of SWCNTs. Then, the recent advances in electronic devices based on s-SWCNTs are reviewed with emphasis on nanoscale s-SWCNTs' high-performance integrated circuits and s-SWCNT-based thin-film transistors (TFT) array and circuits. Lastly, the existing challenges and development trends for the s-SWCNTs and electronic devices are briefly discussed. The aim is to provide some useful information and inspiration for the sorting and purification of s-SWCNTs, as well as the construction of electronic devices with s-SWCNTs.

Solubilization of Carbon Nanotubes with Ethylene-Vinyl Acetate for Solution-Processed Conductive Films and Charge Extraction Layers in Perovskite Solar Cells

Carbon nanotube (CNT) solubilization via non-covalent wrapping of conjugated semiconducting polymers is a common technique used to produce stable dispersions for depositing CNTs from solution. Here, we report the use of a non-conjugated insulating polymer, ethylene vinyl acetate (EVA), to disperse multi- and single-walled CNTs (MWCNT and SWCNT) in organic solvents. We demonstrate that despite the insulating nature of the EVA, we can produce semitransparent films with conductivities of up to 34 S/cm. We show, using photoluminescence spectroscopy, that the EVA strongly binds to individual CNTs, thus making them soluble, preventing aggregation, and facilitating the deposition of high-quality films. To prove the good electronic properties of this composite, we have fabricated perovskite solar cells using EVA/SWCNTs and EVA/MWCNTs as selective hole contact, obtaining power conversion efficiencies of up to 17.1%, demonstrating that the insulating polymer does not prevent the charge transfer from the active material to the CNTs.

Anthanthrene-based conjugated polymers for the dispersion of single-walled carbon nanotubes

Four new copolymers based on anthanthrene for the dispersion of semiconducting SWNTs of various diameters have been synthesized.

Enrichment of Metallic Carbon Nanotubes Using a Two-Polymer Extraction Method

The large-scale enrichment of metallic carbon nanotubes is a challenging goal that has proven elusive. Selective dispersion of carbon nanotubes by specifically designed conjugated polymers is effective for isolating semiconducting species, but a comparable system does not exist for isolating metallic species. Here, we report a two-polymer system where semiconducting species are extracted from the raw HiPCO or plasma-torch nanotube starting material using an electron-rich poly(fluorene-co-carbazole) derivative, followed by isolation of the metallic species remaining in the residue using an electron-poor methylated poly(fluorene-co-pyridine) polymer. Characterization of the electronic nature of extracted samples was carried out via a combination of absorption, Raman, and fluorescence spectroscopy, as well as electrical conductivity measurements. Using this methodology, the metallic species in the sample were enriched 2-fold in comparison to the raw starting material. These results indicate that the use of electron-poor polymers is an effective strategy for the enrichment of metallic species.

Pillar[5]arene-Decorated Single-Walled Carbon Nanotubes

Control of single-walled carbon nanotube dispersion properties is of substantial interest to the scientific community. In this work, we sought to investigate the effect of a macrocycle, pillar[5]arene, on the dispersion properties of a polymer-nanotube complex. Pillar[5]arenes are a class of electron-rich macrocyclic hosts capable of forming inclusion complexes with electron-poor guests, such as alkyl nitriles. A hydroxyl-functionalized pillar[5]arene derivative was coupled to the alkyl bromide side chains of a polyfluorene, which was then used to coat the surface of single-walled carbon nanotubes. Noncovalent functionalization of carbon nanotubes with the macrocycle-containing conjugated polymer significantly enhanced nanotube solubility, resulting in dark and concentrated nanotube dispersions (600 μg mL-1), as evidenced by UV-vis-NIR spectroscopy and thermogravimetric analysis. Differentiation of semiconducting and metallic single-walled carbon nanotube species was analyzed by a combination of UV-vis-NIR, Raman, and fluorescence spectroscopy. Raman spectroscopy confirmed that the concentrated nanotube dispersion produced by the macrocycle-containing polymer was due to well-exfoliated nanotubes, rather than bundle formation. The polymer-nanotube dispersion was investigated using 1H NMR spectroscopy, and it was found that host-guest chemistry between pillar[5]arene and 1,6-dicyanohexane occurred in the presence of the polymer-nanotube complex. Utilizing the host-guest capability of pillar[5]arene, the polymer-nanotube complex was incorporated into a supramolecular organogel.

Tailoring carbon nanotubes optical properties through chirality-wise silicon ring resonators

Semiconducting single walled carbon nanotubes (s-SWNT) have an immense potential for the development of active optoelectronic functionalities in ultra-compact hybrid photonic circuits. Specifically, s-SWNT have been identified as a very promising solution to implement light sources in the silicon photonics platform. Still, two major challenges remain to fully exploit the potential of this hybrid technology: the limited interaction between s-SWNTs and Si waveguides and the low quantum efficiency of s-SWNTs emission. Silicon micro-ring resonators have the potential capability to overcome these limitations, by providing enhanced light s-SWNT interaction through resonant light recirculation. Here, we demonstrate that Si ring resonators provide SWNT chirality-wise photoluminescence resonance enhancement, releasing a new degree of freedom to tailor s-SWNT optical properties. Specifically, we show that judicious design of the micro-ring geometry allows selectively promoting the emission enhancement of either (8,6) or (8,7) SWNT chiralities present in a high-purity polymer-sorted s-SWNT solution. In addition, we present an analysis of nanometric-sized silicon-on-insulator waveguides that predicts stronger light s-SWNT interaction for transverse-magnetic (TM) modes than for conventionally used transverse-electric (TE) modes.

Self-Assembly of Rod-Coil Block Copolymers on Carbon Nanotubes: A Route toward Diverse Surface Nanostructures

In this work, it is reported that poly(γ-benzyl-l-glutamate)-block-poly(ethylene glycol) (PBLG-b-PEG) rod-coil block copolymers (BCPs) can disperse carbon nanotubes (CNTs) in solution and form various surface nanostructures on the CNTs via solution self-assembly. In an organic solvent that dissolves the BCPs, the PBLG rod blocks adsorb on CNT surfaces, and the BCPs form conformal coatings. Then, by the introduction of water, a selective solvent for PEG blocks, the BCPs in the coatings further self-assemble into diverse surface nanostructures, such as helices (left-handed or right-handed), gyros, spheres, and rings. The morphology of the surface nanostructure can be tailored by initial organic solvent composition, preparation temperature, feeding ratio of BCPs to CNTs, degree of polymerization of PBLG blocks, and diameter of the CNTs.

Dopant-Modulated Conjugated Polymer Enrichment of Semiconducting SWCNTs

Conjugated polymer extraction (CPE) is a low-cost, scalable process that can enrich single-walled carbon nanotube (SWCNT) materials in organic media. For other separation methods in aqueous phases, redox chemistry and/or pH control dramatically affect the sorting process of the SWCNTs. We have previously determined that the CPE process can be fine-tuned by adjusting the pH on the tube surface. Here, we systematically studied the effect of redox chemistry on the CPE process by adding organic p-/n-dopants. At a very strong p-/n-doping level, static repulsions dominated the interactions between the tubes and the CPE lost selectivity. When the doping level changed from a medium p-doping to a neutral state, the yield of CPE increased and the selectivity was compromised. We also observed chiral selectivity when a weak p-dopant was used. A photoluminescence excitation mapping under different titration conditions provided more insight into the doping level of the tubes relative to their diameters, chiralities, and redox potentials. We proposed a mechanism for the CPE process. The semiconducting and metallic tubes are separated because of their different solubilities, which are determined by the bundling energy between the tubes and are related to their doping level in polymer solutions.

Sorting of Semiconducting Single-Walled Carbon Nanotubes in Polar Solvents with an Amphiphilic Conjugated Polymer Provides General Guidelines for Enrichment

Conjugated polymer extraction (CPE) has been shown to be a highly effective method to isolate high-purity semiconducting single-walled carbon nanotubes (sc-SWCNTs). In both literature reports and industrial manufacturing, this method has enabled enrichment of sc-SWCNTs with high purity (≥99.9%). High selectivity is typically obtained in nonpolar aromatic solvents, yet polar solvents may provide process improvements in terms of yield, purity and efficiency. Using an amphiphilic fluorene-alt-pyridine conjugated copolymer with hydrophilic side chains, we have investigated the enrichment of sc-SWCNTs in polar solvents. Various conditions such as polymer/SWCNT ratio, solvent polarity, solvent dielectric constant as well as polymer solubility and SWCNT dispersibility were explored in order to optimize the purity and yield of the enriched product. Herein, we provide insights on CPE by demonstrating that a conjugated polymer having a hydrophobic backbone and hydrophilic oligo(ethylene oxide) side chains provides near full recovery (95%) of sc-SWCNTs using a multiextraction protocol. High purity is also obtained, and differences in chiral selectivity compared to analogous hydrophobic systems were confirmed by optical absorption and Raman spectroscopy as well as photoluminescence excitation mapping. Taking into consideration the solvent dielectric constant, polarity index as well as polymer solubility and SWCNT dispersibility provides a better understanding of structure-property effects on sc-SWCNT enrichment. The resulting hydrophilic SWCNT dispersions demonstrate long-term colloidal stability, making them suitable for ink formulation and high-performance thin-film transistors fabrication.

A review of the interfacial characteristics of polymer nanocomposites containing carbon nanotubes

This paper provides an overview of recent advances in research on the interfacial characteristics of carbon nanotube–polymer nanocomposites. The state of knowledge about the chemical functionalization of carbon nanotubes as well as the interaction at the interface between the carbon nanotube and the polymer matrix is presented. The primary focus of this paper is on identifying the fundamental relationship between nanocomposite properties and interfacial characteristics. The progress, remaining challenges, and future directions of research are discussed. The latest developments of both microscopy and scattering techniques are reviewed, and their respective strengths and limitations are briefly discussed. The main methods available for the chemical functionalization of carbon nanotubes are summarized, and particular interest is given to evaluation of their advantages and disadvantages. The critical issues related to the interaction at the interface are discussed, and the important techniques for improving the properties of carbon nanotube–polymer nanocomposites are introduced. Additionally, the mechanism responsible for the interfacial interaction at the molecular level is briefly described. Furthermore, the mechanical, electrical, and thermal properties of the nanocomposites are discussed separately, and their influencing factors are briefly introduced. Finally, the current challenges and opportunities for efficiently translating the remarkable properties of carbon nanotubes to polymer matrices are summarized in the hopes of facilitating the development of this emerging area. Potential topics of oncoming focus are highlighted, and several suggestions concerning future research needs are also presented.

The state of research on the characteristics at the interface in polymer nanocomposites is reviewed. Special emphasis is placed on the recent advances in the fundamental relationship between interfacial characteristics and nanocomposite properties.