An on-line phase measurement system for quality assurance of the BSD 2000. Part I: technical description of the measurement system

Design and test of a 434 MHz multi-channel amplifier system for targeted hyperthermia applicators

PURPOSE

For our head-and-neck hyperthermia (HT) applicator, an amplifier system with full amplitude and phase-control to deliver the radio-frequency signals, was not available. We therefore designed and tested a 433.92 MHz multi-channel amplifier system.

SYSTEM DESCRIPTION

The design consists of a direct digital synthesizer (DDS) system that generates 12 phase-controlled coherent 433.92 MHz signals, which are amplified to maximum 200 W output per channel. Directional couplers are placed at the amplifiers to couple a small portion of both forward and reflected signals to gain-and-phase detectors. The power setting is applied with a resolution of 2 W and for the phase it is 0.1 degrees . The channels are sequentially sampled at 100 Hz per channel.

METHODS

We tested the performance of the designed amplifier system by measuring the RF spectrum, power and phase accuracy, and by characterising the feedback control by using highly accurate power and phase meters.

RESULTS

The spurious emission is less than 60 dBc and the first two harmonic frequencies are suppressed more than 45 dB. The measurement accuracy for the power (+/-5%) is valid for at least 20 days after calibration and for the phase (+/-5 degrees ) it is valid for at least 2 months.

CONCLUSIONS

The amplifier system operates according to our design criteria to support targeted HT. It can be used for both our in-house developed superficial and head-and-neck HT applicators or any other HT applicator that works on the same frequency of 433.92 MHz.

Evaluation of power and phase accuracy of the BSD Dodek amplifier for regional hyperthermia using an external vector voltmeter measurement system

PURPOSE

Accurate monitoring of RF (radio frequency) power and phase is a key part of quality assurance (QA) for phased-array hyperthermia systems. In order to assess the steering capability of the BSD 2000 3D facility, an independent measurement system has been implemented, using a vector voltmeter (VVM) as the measuring device.

METHODS

This paper describes the calibration of the RF signal paths from each of the 12 BSD Dodek amplifier outputs to the VVM instrument readout. Periodical network analyser measurements show that the uncertainty of the measured power using the VVM system is <4% for all channels, while the uncertainty of the phase measurements is <0.3 degrees. The values are comparable to those reported for similar monitoring systems and are considered adequate for monitoring of the BSD Dodek steering parameters.

RESULTS

Using the VVM system to investigate the accuracy of the BSD Dodek amplifier power and phase control, systematic differences were observed between the requested and the measured power for all channels: At a requested power level of 25 W per channel, the measured power level was on average 15% lower than nominal, whereas at 100 W it was nearly 20% higher. It was also observed that the absolute phase values are nearly 30 degree higher at 25W per channel than at power levels > or = 50W per channel. Under certain circumstances, these issues may reduce target steering accuracy for the BSD 2000 3D system; on the other hand, the Dodek power and phase control stability is found to be acceptable.

CONCLUSIONS

The results emphasize the need for accurate, independent online power and phase QA during regional hyperthermia treatments using phased array systems.

An on-line phase measurement system for quality assurance of the BSD 2000. Part II: results of the phase measurement system

Phase constancy and accuracy are significant for regional hyperthermia with phased array radiofrequency hyperthermia systems. They are both necessary for a precise target steering in therapy. For the BSD 2000 system (BSD Medical Corp. Salt Lake City, Utah, USA), the phase values of all channels are checked with a self-developed automatic on-line phase measurement system. On different days the phases are measured under identical conditions, where the output paths are cut off with 50 ohm dummy loads to suppress the influence of the radiation conditions of the antennae on the measurement values. The results show how the phase values of the four channels change in the first 30 min and from day to day. During this time interval after the start the phases drop down by up to 15 degrees. For the time later changes are very slight and the differences from day to day are negligible. The phase shift that occurs in the first 30 min is as high as a change of the target point by 1 cm. Earlier switching on of the amplifiers prevents this shift occurring during the treatment. The measurement system provides a good tool for determination of phase accuracy and is easy to realize.