Membranes with Great Hydrophobicity: A Review on Preparation and Characterization

Electrospun nanofibers based on zein and red onion bulb extract (Allium cepa, L.): Volatile compounds, hydrophilicity, and antioxidant activity

Onion is rich in bioactive and volatile compounds with antioxidant activity. However, the pungent odor of volatile compounds (VOCs) released restricts its use. The encapsulation of red onion extract by electrospinning is an alternative to mask this odor and protect its bioactive compounds. The main objective of this study was to encapsulate red onion bulb extract (ROE) in different concentrations into zein nanofibers by electrospinning and evaluate their thermal, antioxidant, and hydrophilicity properties. The major VOC in ROE was 3(2H)-furanone, 2-hexyl-5-methyl. Incorporating ROE into the polymeric solutions increased electrical conductivity and decreased apparent viscosity, rendering nanofibers with a lower average diameter. The loading capacity of ROE on fibers was high, reaching 91.5% (10% ROE). The morphology of the nanofibers was random and continuous; however, it showed beads at the highest ROE concentration (40%). The addition of ROE to the nanofibers increased their hydrophilicity. The nanofibers' antioxidant activity against 2,2-diphenyl-1-picrylhydrazyl, nitric oxide, and hydroxyl radicals ranged from 32.5% to 57.3%. The electrospun nanofibers have the potential to protect and mask VOCs. In addition, they offer a sustainable alternative to the synthetic antioxidants commonly employed in the food and packaging industry due to their antioxidant activities.

Starch extraction from avocado by-product and its use for encapsulation of ginger essential oil by electrospinning

Starches from alternative sources, such as avocado seed, have potential for application in the encapsulation of essential oils. This study aimed to extract starch from avocado seeds and its use as wall material to encapsulate ginger essential oil (GEO), at different concentrations. The fibers were produced by electrospinning and evaluated by morphology, size, infrared spectra, thermogravimetric properties, contact angle, loading capacity, and antibacterial activity. The major compounds in GEO were α-zingiberene, β-sesquiphellandrene, α-farnesene, and α-curcumene. The starch-GEO fibers presented a higher diameter (∼553 nm) than those without GEO (345 nm). Encapsulation of GEO in starch fibers increased their thermal degradation temperatures from 165.8 °C (free GEO) to 257.6 °C (40 % GEO fibers). The starch-GEO fibers presented characteristic bands of their constituents by infrared spectra. Loading capacity ranged from 44 to 54 %. The fibers showed hydrophilic character, with a contact angle of <90°. Free GEO and the fibers with 50 % of GEO displayed antibacterial activity against Escherichia coli, proving the bioactivity of the starch-GEO fibers and its possible applicability for food packaging. Avocado seed starch showed to be a great wall material for GEO encapsulation.

Design of Microstructure-Engineered Polymers for Energy and Environmental Conservation

With the ever-growing demand for sustainability, designing polymeric materials using readily accessible feedstocks provides potential solutions to address the challenges in energy and environmental conservation. Complementing the prevailing strategy of varying chemical composition, engineering microstructures of polymer chains by precisely controlling their chain length distribution, main chain regio-/stereoregularity, monomer or segment sequence, and architecture creates a powerful toolbox to rapidly access diversified material properties. In this Perspective, we lay out recent advances in utilizing appropriately designed polymers in a wide range of applications such as plastic recycling, water purification, and solar energy storage and conversion. With decoupled structural parameters, these studies have established various microstructure-function relationships. Given the progress outlined here, we envision that the microstructure-engineering strategy will accelerate the design and optimization of polymeric materials to meet sustainability criteria.

Red onion skin extract rich in flavonoids encapsulated in ultrafine fibers of sweet potato starch by electrospinning

Electrospinning encapsulation is a highly viable method to protect bioactive compounds and prevent their degradation. Hence, this study produced ultrafine fibers based on yellow and white sweet potato starches and a red onion skin extract (ROSE; 0, 3, 6, and 9 %, w/w) using electrospinning. The fibers were evaluated for morphology, thermogravimetric properties, antioxidant, in vitro release simulation, thermal resistance (100 and 180 °C), and wettability. The fibers with ROSE presented 251-611 nm diameters, 67-78 % loading capacity, and 51.6-95.4 and 13.4-99.4 % thermal resistance (100 and 180 °C, respectively); apigenin presented the highest thermal protection. The phenolic compounds showed low release using 10 % ethanol and greater release with 50 % ethanol. The fibers with 9 % ROSE showed 2,2'-azino-bis(3-ethylbenzothiazoline) 6-sulfonic acid radical inhibition above 92 %. The ultrafine fibers and the unencapsulated ROSE showed inhibitory action against Escherichia coli and Staphylococcus aureus; only unencapsulated ROSE showed bactericidal activity.

Fabrication and design of poly(l-lactic acid) membrane for passive MAP packaging of Brassica chinensis L

PLD_x L copolymers were synthesized from physically stable rigid poly(l-lactic acid) (PLLA) and a few different molecular weights of polydimethylsiloxane (PDMS) to increase the O₂ and CO₂ permeabilities of PLLA films and make them acceptable for packaging highly respirable products. The effect of PDMS on the morphology, mechanical properties, and gas permeability of PLD_x L was investigated. Copolymers showed approximately 10 times the fracture strain and 1.7 times the CO₂ and O₂ permeabilities of neat PLLA. Additionally, PLD_x L maintained an increased CO₂ /O₂ perm-selectivity consistent between 5 and 40°C. Passive modified atmosphere packaging of Brassica chinensis L was developed to assess the membrane's impact on headspace gas inside the package. The results showed that poly(amide)/poly(ethylene) packaging with 48 cm² PLD_1.8 L membrane as a breathing window can provide 50 g B. chinensis L. with a healthy atmosphere of 3%-8% O₂ and 5%-8% CO₂ between 6 and 22 days. Vegetables packaged in PLD_1.8 L had the lower respiration rate, lower nitrite contents, and less proliferation of microorganisms. Moreover, a suitable atmosphere kept vegetables with higher ascorbic acid and a good appearance after more than 2 weeks of storage at 5°C. PRACTICAL APPLICATION: The permeability of the PLLA-based membrane can be adjusted for the breathable window membrane of sealed fresh products. In the future, several types of film could be developed to match the respiratory and metabolic characteristics of different kinds of products. Such PLLA-based specialized membranes can refine the fresh-keeping function and be more attractive to the customer.

Effect of Methacrylic Acid Monomer on UV-Grafted Polyethersulfone Forward Osmosis Membrane

UV irradiation is one of the procedures that has been considered for membrane surface graft polymerization. It is commonly utilized for enhancing the wettability of polyethersulfone (PES) membranes. In this research study, the monomer methacrylic acid (MAA) was used for the UV grafting process of a commercial NF2 PES membrane for the preparation of a forward osmosis (FO) membrane. Three different monomer concentrations and three different UV irradiation times were considered. The intrinsic characteristics of both the surface-modified and pristine membranes were determined via a non-pressurized test method. Compared to the NF2 PES, the surface of the modified membranes was rendered more hydrophilic, as the measured water contact angle was reduced considerably from 65° to 32-58°. The membrane surface modification was also confirmed by the data collected from other techniques, such as atomic force microscopy (AFM), field emission-scanning electron microscope (FESEM) and Fourier-transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR). Additionally, the modified membranes exhibited a greater water permeate flux (J_w) compared to the NF2 PES membrane. In this study, the water permeability (A), solute permeability (B) and structural parameter (S) were determined via a two-stage FO non-pressurized test method, changing the membrane orientation. Compared to the FO pressurized test, smaller S values were obtained with significantly high A and B values for the two non-pressurized tests. The adopted method in the current study is more adequate for determining the intrinsic characteristics of FO membranes.

Effect of OH-Group Introduction on Gas and Liquid Separation Properties of Polydecylmethylsiloxane

Membrane development for specific separation tasks is a current and important topic. In this work, the influence of OH-groups introduced in polydecylmethylsiloxane (PDecMS) was shown on the separation of CO₂ from air and aldehydes from hydroformylation reaction media. OH-groups were introduced to PDecMS during hydrosilylation reaction by adding 1-decene with undecenol-1 to polymethylhydrosiloxane, and further cross-linking. Flat sheet composite membranes were developed based on these polymers. For obtained membranes, transport and separation properties were studied for individual gases (CO₂, N₂, O₂) and liquids (1-hexene, 1-heptene, 1-octene, 1-nonene, heptanal and decanal). Sorption measurements were carried out for an explanation of difference in transport properties. The general trend was a decrease in membrane permeability with the introduction of OH groups. The presence of OH groups in the siloxane led to a significant increase in the selectivity of permeability with respect to acidic components. For example, on comparing PDecMS and OH-PDecMS (~7% OH-groups to decyl), it was shown that selectivity heptanal/1-hexene increased eight times.

Elucidating the Molecular Structure of Hydrophobically Modified Polyethylenimine Nanoparticles and Its Potential Implications for DNA Binding

The structural properties of the polyethylenimine (PEI) polymer are generally tuned and selectively modified to reinforce its potential in a broad spectrum of applied domains of medicine, healthcare, material design, sensing, and electronic optimization. The selective modification of the polymer brings about changes in its interfacial characteristics and behavior. The current work involves the synthesis of naphthalimide conjugated polyethylenimine organic nanoparticles (NPEI-ONPs). The interfacial molecular structure of NPEI-ONPs is explored in an aqueous medium at pH 7.4 using surface tensiometry and sum-frequency generation vibrational spectroscopy (SFG-VS). The hydrophobic functionalization rendered a concentration-dependent surface coverage of NPEI-ONPs, where the SFG-VS analysis exhibited the molecular rearrangement of its hydrophobic groups at the interface. The interaction of NPEI-ONPs with double-stranded DNA (dsDNA) is carried out to observe the relevance of the synthesized nanocomposites in the biomedical domain. The bulk-specific studies (i.e., thermal denaturation, viscometry, zeta (ζ) potential, and ATR-FTIR) reveal the condensation of dsDNA in the presence of NPEI-ONPs, making its structure more compact. The interface-sensitive SFG-VS showcased the impact of the dsDNA and NPEI-ONP interaction on the interfacial molecular behavior of NPEI-ONPs at the air-aqueous interface. Our results exhibit the potential of such hydrophobically functionalized ONPs as promising candidates for developing biomedical sealants, substrate coatings, and other biomedical domains.

Membranes for Oil/Water Separation: A Review

Recent advancements in separation and membrane technologies have shown a great potential in removing oil from wastewaters effectively. In addition, the capabilities have improved to fabricate membranes with tunable properties in terms of their wettability, permeability, antifouling, and mechanical properties that govern the treatment of oily wastewaters. Herein, authors have critically reviewed the literature on membrane technology for oil/water separation with a specific focus on: 1) membrane properties and characterization, 2) development of various materials (e.g., organic, inorganic, and hybrid membranes, and innovative materials), 3) membranes design (e.g., mixed matrix nanocomposite and multilayers), and 4) membrane fabrication techniques and surface modification techniques. The current challenges and future research directions in materials and fabrication techniques for membrane technology applications in oil/water separation are also highlighted. Thus, this review provides helpful guidance toward finding more effective, practical, and scalable solutions to tackle environmental pollution by oils.

Fouling, performance and cost analysis of membrane-based water desalination technologies: A critical review

While water is a key resource required to sustain life, freshwater sources and aquifers are being depleted at an alarming rate. As a mitigation strategy, saline water desalination is commonly used to supplement the available water resources beyond direct water supply. This is achieved through effective advanced water purification processes enabled to handle complex matrix of saline wastewater. Membrane technology has been extensively evaluated for water desalination. This includes the use of reverse osmosis (RO) (the most mature membrane technology for desalination), pervaporation (PV), electrodialysis (ED), membrane distillation (MD), and membrane crystallization (MCr). Though nanofiltration (NF) is not mainly applied for desalination purposes, it is included in the reviewed processes because of its ability to reach 90% salt rejection efficiency for water softening. However, its comparison with other technologies is not provided since NF cannot be used for removal of NaCl during desalination. Remarkably, membrane processes remain critically affected by several challenges including membrane fouling. Moreover, capital expenditure (CAPEX) and operating expenditure (OPEX) are the key factors influencing the establishment of water desalination processes. Therefore, this paper provides a concise and yet comprehensive review of the membrane processes used to desalt saline water. Furthermore, the successes and failures of each process are critically reviewed. Finally, the CAPEX and OPEX of these water desalination processes are reviewed and compared. Based on the findings of this review, MD is relatively comparable to RO in terms of process performance achieving 99% salt rejections. Also, high salt rejections are reported on ED and PV. The operation and maintenance (O&M) costs remain lower in ED. Notably, the small-scale MD OPEX falls below that of RO. However, the large-scale O&M in MD is rarely reported due to its slow industrial growth, thus making RO the most preferred in the current water desalination markets.

Non-Solvent Influence of Hydrophobic Polymeric Layer Deposition on PVDF Hollow Fiber Membrane for CO2 Gas Absorption

The implementation of hydrophobicity on membranes is becoming crucial in current membrane technological development, especially in membrane gas absorption (MGA). In order to prevent membrane wetting, a polypropylene (PP) dense layer coating was deposited on a commercial poly(vinylidene fluoride) (PVDF) hollow fiber membrane as a method of enhancing surface hydrophobicity. The weight concentration of PP pellets was varied from 10 mg mL-1 to 40 mg mL-1 and dissolved in xylene. A two-step dip coating was implemented where the PVDF membrane was immersed in a non-solvent followed by a polymer coating solution. The effects of the modified membrane with the non-solvent methyl ethyl ketone (MEK) and without the non-solvent was investigated over all weight concentrations of the coating solution. The SEM investigation found that the modified membrane surface transfiguration formed microspherulites that intensified as PP concentration increased with and without MEK. To understand the coating formation further, the solvent-non-solvent compatibility with the polymer was also discussed in this study. The membrane characterizations on the porosity, the contact angle, and the FTIR spectra were also conducted in determining the polymer coating properties. Hydrophobic membrane was achieved up to 119.85° contact angle and peak porosity of 87.62% using MEK as the non-solvent 40 mg mL-1 PP concentration. The objective of the current manuscript was to test the hydrophobicity and wetting degree of the coating layer. Hence, physical absorption via the membrane contactor using CO2 as the feed gas was carried out. The maximum CO2 flux of 3.33 × 10-4 mol m-2 s-1 was achieved by 25 mg modified membrane at a fixed absorbent flow rate of 100 mL min-1 while 40 mg modified membrane showed better overall flux stability.

Seawater Desalination by Modified Membrane Distillation: Effect of Hydrophilic Surface Modifying Macromolecules Addition into PVDF Hollow Fiber Membrane

Hollow fiber membranes of polyvinylidene fluoride (PVDF) were prepared by incorporating varying concentrations of hydrophilic surface-modifying macromolecules (LSMM) and a constant amount of polyethylene glycol (PEG) additives. The membranes were fabricated by the dry-wet spinning technique. The prepared hollow fiber membranes were dip-coated by hydrophobic surface-modifying macromolecules (BSMM) as the final step fabrication. The additives combination is aimed to produce hollow fiber membranes with high flux permeation and high salt rejection in the matter of seawater desalination application. This study prepares hollow fiber membranes from the formulation of 18 wt. % of PVDF mixed with 5 wt. % of PEG and 3, 4, and 5 wt. % of LSMM. The membranes are then dip-coated with 1 wt. % of BSMM. The effect of LSMM loading on hydrophobicity, morphology, average pore size, surface porosity, and membrane performance is investigated. Coating modification on LSMM membranes showed an increase in contact angle up to 57% of pure, unmodified PVDF/PEG membranes, which made the fabricated membranes at least passable when hydrophobicity was considered as one main characteristic. Furthermore, The PVDF/PEG/4LSMM-BSMM membrane exhibits 161 °C of melting point as characterized by the DSC. This value indicates an improvement of thermal behavior shows so as the fabricated membranes are desirable for membrane distillation operation conditions range. Based on the results, it can be concluded that PVDF/PEG membranes with the use of LSMM and BSMM combination could enhance the permeate flux up to 81.32 kg·m-2·h-1 at the maximum, with stable salt rejection around 99.9%, and these are found to be potential for seawater desalination application.

Membranes for the Gas/Liquid Phase Separation at Elevated Temperatures: Characterization of the Liquid Entry Pressure

Hydrophobic membranes were characterized at elevated temperatures. Pressure was applied at the feed and permeate side to ensure liquid phase conditions. Within this scope, the applicability of different polymeric and ceramic membranes in terms of liquid entry pressure was studied using water. The Visual Method and the Pressure Step Method were applied for the experimental investigation. The results show the Pressure Step Method to be an early detection method. The tests at higher pressure and temperature conditions using the Pressure Step Method revealed the temperature as being the main factor affecting the liquid entry pressure. Novel LEP data up to 120 °C and 2.5 bar were obtained, which broadens the application range of hydrophobic membranes.

Semiconducting graphitic carbon nitride integrated membranes for sustainable production of clean water: A review

Semiconducting membranes integrated with nanomaterials have placed themselves in new emerging researches tremendously for seawater desalination, oil-water separation, disinfection, removal of inorganic as well as organic pollutants. Howbeit, only nanoparticles unified membranes show quite a lot lags in their performance, although some of these particles associated with the demerits of high cost. In contrast, graphitic carbon nitride incorporated membranes offered improved aforementioned properties corresponding to absolute essential qualities such as cost-effective, environmentally friendly, easy-to-operate, green manufacturing, anti-fouling, and low energy consumption. Moreover, their high mechanical strength, high stability against harsh environment and long-term utilization without flux reduction are strong plus. Even though there are some undeniable downsides of these membranes in real world applications as bulk synthesis, consistent dispersion of graphitic carbon nitride, low photocatalytic efficiency etc. Accordingly, in the present article, these frailties of the membranes having graphitic carbon nitride as a filler and their respective synthesis procedures and properties are discussed. A comprehensive analysis over the application of semiconducting graphitic carbon nitride incorporated membranes with and without special surface modification; and exploration of the future challenges and difficulties associated to these membranes are also reviewed. Consequently, the current article provides brief overview about graphitic carbon nitride integrated composite membranes as well as their applications, and it finished up with new thoughts of further improvements/modifications to overcome their shortcomings in actual environmental conditions.

Modification of porous polyetherimide hollow fiber membrane by dip-coating of Zonyl® BA for membrane distillation of dyeing wastewater

Wetting and fouling have significantly affected the application of membrane distillation (MD). In this work, a dip-coating method was used for improving surface hydrophobicity of the polyetherimide (PEI) hollow fiber membrane. An air gap membrane distillation (AGMD) process was applied for treatment of the methylene blue (MB) solution. The porous PEI membrane was fabricated by a dry-wet spinning process and the hydrophobic 2-(Perfluoroalkyl) ethanol (Zonyl^® BA) was used as the coating material. From FESEM, the modified PEI-Zonyl membrane showed an open structure with large finger-like cavities. The modified membrane displayed a narrow pore size distribution with mean pore size of 0.028 μm. The outer surface contact angle of the PEI-Zonyl membrane increased from 81.3° to 100.4° due to the formation of an ultra-thin coated layer. The pure water flux of the PEI-Zonyl membrane was slightly reduced compared to the pristine PEI membrane. A permeate flux of 6.5 kg/m² h and MB rejection of 98% were found for the PEI-Zonyl membrane during 76 h of the AGMD operation. Adsorption of MB on the membrane surface was confirmed based on the Langmuir isotherm evaluation, AFM and FESEM analysis. The modified PEI-Zonyl membrane can be a favorable alternative for AGMD of dyeing wastewaters.

Fabrication and Characterization of Hydrophobic Porous Metallic Membranes for High Temperature Applications

Hydrophobic porous metallic membranes can be integrated in a microreactor for in situ separation of steam at high temperatures. This study investigates the fabrication and characterization of hydrophobic coatings on metallic substrates. Two different coating methods were explored: (1) Plasma Enhanced—Chemical Vapor Deposition (PE-CVD) to form amorphous carbon silicon-doped a-C:H:Si:O thin films and (2) Direct Immersion in fluoroalkyl silane (FAS-13) solution using dip coating to form Self-Assembled Monolayers. The results on wettability as well as SEM images and EDS/WDS analyses indicate that the coated sintered stainless steel membranes are adequate as hydrophobic surfaces, maintaining the porosity of the substrate and withstanding high temperatures. Especially the FAS-13 coating shows very good resistance to temperatures higher than 250 °C. These findings are of special significance for the fabrication of porous metal membranes for separation of steam in high temperature applications.

Boron Nitride Nanotube (BNNT) Membranes for Energy and Environmental Applications

Owing to their extraordinary thermal, mechanical, optical, and electrical properties, boron nitride nanotubes (BNNTs) have been attracting considerable attention in various scientific fields, making it more promising as a nanomaterial compared to other nanotubes. Recent studies reported that BNNTs exhibit better properties than carbon nanotubes, which have been extensively investigated for most environment-energy applications. Irrespective of its chirality, BNNT is a constant wide-bandgap insulator, exhibiting thermal oxidation resistance, piezoelectric properties, high hydrogen adsorption, ultraviolet luminescence, cytocompatibility, and stability. These unique properties of BNNT render it an exceptional material for separation applications, e.g., membranes. Recent studies reported that water filtration, gas separation, sensing, and battery separator membranes can considerably benefit from these properties. That is, flux, rejection, anti-fouling, sensing, structural, thermal, electrical, and optical properties of membranes can be enhanced by the contribution of BNNTs. Thus far, a majority of studies have focused on molecular simulation. Hence, the requirement of an extensive review has emerged. In this perspective article, advanced properties of BNNTs are analyzed, followed by a discussion on the advantages of these properties for membrane science with an overview of the current literature. We hope to provide insights into BNNT materials and accelerate research for environment-energy applications.

Facile Approaches of Polymeric Face Masks Reuse and Reinforcements for Micro-Aerosol Droplets and Viruses Filtration: A Review

Since the widespread of severe acute respiratory syndrome of coronavirus 2 (SARS-CoV-2) disease, the utilization of face masks has become omnipresent all over the world. Face masks are believed to contribute to an adequate protection against respiratory infections spread through micro-droplets among the infected person to non-infected others. However, due to the very high demands of face masks, especially the N95-type mask typically worn by medical workers, the public faces a shortage of face masks. Many papers have been published recently that focus on developing new and facile techniques to reuse and reinforce commercially available face masks. For instance, the N95 mask uses a polymer-based (membrane) filter inside, and the filter membrane can be replaced if needed. Another polymer sputtering technique by using a simple cotton candy machine could provide a cheap and robust solution for face mask fabrication. This review discuss the novel approaches of face mask reuse and reinforcement specifically by using membrane-based technology. Tuning the polymeric properties of face masks to enhance filterability and virus inactivity is crucial for future investigation.

Metallic Liquid Gating Membranes

The development of liquid gating membrane (LGM) systems with tunable multiphase selectivity and antifouling properties is limited by the mechanical stability of the membrane materials. The mechanical integrity of most polymeric membranes can be compromised by deformation under harsh operating conditions (elevated temperatures, corrosive environments, foulants, etc.), ultimately leading to their failure. Here, a facile electrochemical approach to the fabrication of multifunctional metal-based liquid gating membrane systems is presented. The membrane porosity, pore size, and membrane surface roughness can be tuned from micro- to nanometer scale, enabling function under a variety of operating conditions. The prepared LGMs demonstrate controllable gas-liquid selectivity, superior resistance to corrosive conditions and fouling chemicals, and significant reduction of the transmembrane pressure required for the separation process, resulting in lower energy consumption. The stability of the gating liquid is confirmed experimentally through sustained fouling resistance and further supported by the interfacial energy calculations. The mechanically robust metal-based membrane systems reported in this study significantly extend the operating range of LGMs, prompting their applications in water treatment processes such as wastewater treatment, degassing, and multiphase separation.

Performance of Polymer Electrolyte Membrane for Direct Methanol Fuel Cell Application: Perspective on Morphological Structure

Membrane morphology plays a great role in determining the performance of polymer electrolyte membranes (PEMs), especially for direct methanol fuel cell (DMFC) applications. Membrane morphology can be divided into two types, which are dense and porous structures. Membrane fabrication methods have different configurations, including dense, thin and thick, layered, sandwiched and pore-filling membranes. All these types of membranes possess the same densely packed structural morphology, which limits the transportation of protons, even at a low methanol crossover. This paper summarizes our work on the development of PEMs with various structures and architecture that can affect the membrane's performance, in terms of microstructures and morphologies, for potential applications in DMFCs. An understanding of the transport behavior of protons and methanol within the pores' limits could give some perspective in the delivery of new porous electrolyte membranes for DMFC applications.

Development of Polymeric Membranes Based on Quaternized Polysulfones for AMFC Applications

A series of quaternary ammonium-functionalized polysulfones were successfully synthesized using a chloromethylation two-step method. In particular, triethylammonium and trimethylammonium polysulfone derivatives with different functionalization degrees from 60% to 150% were investigated. NMR spectroscopic techniques were used to determine the degree of functionalization of the polymers. The possibility to predict the functionalization degree by a reaction tool based on a linear regression was highlighted. Anionic membranes with a good homogeneity of thickness were prepared using a doctor-blade casting method of functionalized polymers. The chemical–physical data showed that ion exchange capacity, water content, and wettability increase with the increase of functionalization degree. A higher wettability was found for membranes prepared by the trimethylamine (TMA) quaternary ammonium group. A degree of functionalization of 100% was chosen for an electrochemical test as the best compromise between chemical–physical properties and mechanical stability. From anionic conductivity measurement a better stability was found for the triethylamine (TEA)-based membrane due to a lower swelling effect. A power density of about 300 mW/cm² for the TEA-based sample at 60 °C in a H₂/O₂ fuel cell was found.

Synthesis, characterization and applications of metallic nanoparticles/rGO blended poly methyl methacrylate membranes for the efficient removal of Cd2+ from model and real wastewater

Herein we report the fabrication of polymer blended hybrid membranes from poly methyl methacrylate (PMMA) as a matrix, and reduced graphene oxide (rGO) and Fe₂O₃, ZnO, CuO and AgO nanoparticles (NPs) as primary and secondary fillers, respectively.