Investigation of elastomeric materials for bolus using stereolithography printing technology in radiotherapy

Dosimetric Evaluation of Commercially Available Flat vs. Self-Produced 3D-Conformal Silicone Boluses for the Head and Neck Region

Background

Boluses are routinely used in radiotherapy to modify surface doses. Nevertheless, considerable dose discrepancies may occur in some cases due to fit inaccuracy of commercially available standard flat boluses. Moreover, due to the simple geometric design of conventional boluses, also surrounding healthy skin areas may be unintentionally covered, resulting in the unwanted dose buildup. With the fused deposition modeling (FDM) technique, there is a simple and possibly cost-effective way to solve these problems in routine clinical practice. This paper presents a procedure of self-manufacturing bespoke patient-specific silicone boluses and the evaluation of buildup and fit accuracy in comparison to standard rectangular commercially available silicone boluses.

Methods

3D-conformal silicone boluses were custom-built to cover the surgical scar region of 25 patients who received adjuvant radiotherapy of head and neck cancer at the University Hospital Würzburg. During a standard CT-based planning procedure, a 5-mm-thick 3D bolus contour was generated to cover the radiopaque marked surgical scar with an additional safety margin. From these digital contours, molds were 3D printed and poured with silicone. Dose measurements for both types of boluses were performed with radiochromic films (EBT3) at three points per patient—at least one aimed to be in the high-dose area (scar) and one in the lower-dose area (spared healthy skin). Surface–bolus distance, which ideally should not be present, was determined from cone-beam CT performed for positioning control. The dosimetric influence of surface–bolus distance was also determined on slab phantom for different field sizes. The trial was performed with hardware that may be routinely available in every radiotherapy department, with the exception of the 3D printer. The required number of patients was determined based on the results of preparatory measurements with the help of the statistical consultancy of the University of Würzburg. The number of measuring points represents the total number of patients.

Results

In the high-dose area of the scar, there was a significantly better intended dose buildup of 2.45% (95%CI 0.0014–0.0477, p = 0.038, N = 30) in favor of a 3D-conformal bolus. Median distances between the body surface and bolus differed significantly between 3D-conformal and commercially available boluses (3.5 vs. 7.9 mm, p = 0.001). The surface dose at the slab phantom did not differ between commercially available and 3D-conformal boluses. Increasing the surface–bolus distance from 5 to 10 mm decreased the surface dose by approximately 2% and 11% in the 6 × 6- and 3 × 3-cm² fields, respectively. In comparison to the commercially available bolus, an unintended dose buildup in the healthy skin areas was reduced by 25.9% (95%CI 19.5–32.3, p < 0.01, N = 37) using the 3D-conformal bolus limited to the region surrounding the surgical scar.

Conclusions

Using 3D-conformal boluses allows a comparison to the commercially available boluses’ dose buildup in the covered areas. Smaller field size is prone to a larger surface–bolus distance effect. Higher conformity of 3D-conformal boluses reduces this effect. This may be especially relevant for volumetric modulated arc therapy (VMAT) and intensity-modulated radiotherapy (IMRT) techniques with a huge number of smaller fields. High conformity of 3D-conformal boluses reduces an unintended dose buildup in healthy skin. The limiting factor in the conformity of 3D-conformal boluses in our setting was the immobilization mask, which was produced primarily for the 3D boluses. The mask itself limited tight contact of subsequently produced 3D-conformal boluses to the mask-covered body areas. In this respect, bolus adjustment before mask fabrication will be done in the future setting.

3D Printing Polymer-based Bolus Used for Radiotherapy

Bolus is a kind of auxiliary device used in radiotherapy for the treatment of superficial lesions such as skin cancer. It is commonly used to increase skin dose and overcome the skin-sparing effect. Despite the availability of various commercial boluses, there is currently no bolus that can form full contact with irregular surface of patients' skin, and incomplete contact would result in air gaps. The resulting air gaps can reduce the surface radiation dose, leading to a discrepancy between the delivered dose and planned dose. To avoid this limitation, the customized bolus processed by three-dimensional (3D) printing holds tremendous potential for making radiotherapy more efficient than ever before. This review mainly summarized the recent development of polymers used for processing bolus, 3D printing technologies suitable for polymers, and customization of 3D printing bolus. An ideal material for customizing bolus should not only have the feature of 3D printability for customization, but also possess radiotherapy adjuvant performance as well as other multiple compound properties, including tissue equivalence, biocompatibility, antibacterial activity, and antiphlogosis.

Three-Dimensional Printing Chitosan-Based Bolus Used for Radiotherapy

A bolus is a kind of tissue equivalent material used in radiotherapy for treating superficial lesions. Despite the availability of various commercial boluses, it is hard for them to form full contact with the irregular surface of patients' skin, such as the scalp, nose, and ear, resulting in air gaps and leading to a discrepancy between the delivered dose and planned dose. To solve this problem, we provided a photocurable bioink created from chitosan (CHI) for digital light processing (DLP) three-dimensional (3D) printing the bolus in radiotherapy application. The chitosan-based bioink (CHI-MA) was obtained by a methacrylation process using methacrylic anhydride (MA). Photosensitive crosslinkers with different molecular weights were introduced into the bioink. The photocuring efficiency and mechanical properties of CHI-MA hydrogels can be well modulated by varying the crosslinkers. This CHI-MA bioink allowed us to create complex structures with reliable biocompatibility, good flexibility, and excellent structural stability. Furthermore, the nose bolus processed by 3D printing this bioink proved to be a good fit for the nose model and showed a desirable radiotherapy effect. This suggests that DLP 3D printing of the CHI-MA bioink would be a promising approach to obtain the customized bolus in the application of radiotherapy.