Distal Femoral Fixation: A Biomechanical Comparison of Trigen Retrograde Intramedullary (I.M.) Nail, Dynamic Condylar Screw (DCS), and Locking Compression Plate (LCP) Condylar Plate

Biomechanical design optimization of distal femur locked plates: A review

Clinical findings, manufacturer instructions, and surgeon's preferences often dictate the implantation of distal femur locked plates (DFLPs), but healing problems and implant failures still persist. Also, most biomechanical researchers compare a particular DFLP configuration to implants like plates and nails. However, this begs the question: Is this specific DFLP configuration biomechanically optimal to encourage early callus formation, reduce bone and implant failure, and minimize bone "stress shielding"? Consequently, it is crucial to optimize, or characterize, the biomechanical performance (stiffness, strength, fracture micro-motion, bone stress, plate stress) of DFLPs influenced by plate variables (geometry, position, material) and screw variables (distribution, size, number, angle, material). Thus, this article reviews 20 years of biomechanical design optimization studies on DFLPs. As such, Google Scholar and PubMed websites were searched for articles in English published since 2000 using the terms "distal femur plates" or "supracondylar femur plates" plus "biomechanics/biomechanical" and "locked/locking," followed by searching article reference lists. Key numerical outcomes and common trends were identified, such as: (a) plate cross-sectional area moment of inertia can be enlarged to lower plate stress at the fracture; (b) plate material has a larger influence on plate stress than plate thickness, buttress screws, and inserts for empty plate holes; (c) screw distribution has a major influence on fracture micro-motion, etc. Recommendations for future work and clinical implications are then provided, such as: (a) simultaneously optimizing fracture micro-motion for early healing, reducing bone and implant stresses to prevent re-injury, lowering "stress shielding" to avoid bone resorption, and ensuring adequate fatigue life; (b) examining alternate non-metallic materials for plates and screws; (c) assessing the influence of condylar screw number, distribution, and angulation, etc. This information can benefit biomedical engineers in designing or evaluating DFLPs, as well as orthopedic surgeons in choosing the best DFLPs for their patients.

Smart fracture plate for quantifying fracture healing: Preliminary efficacy in a biomechanical model

The diagnosis of fracture nonunion following plate osteosynthesis is subjective and frequently ambiguous. Initially following osteosynthesis, loads applied to the bone are primarily transmitted through the plate. However, as callus stiffness increases, the callus is able to bear load proportional to its stiffness while forces through the plate decrease. The purpose of this study was to use a "smart" fracture plate to distinguish between phases of fracture healing by measuring forces transmitted through the plate. A wireless force sensor and small adapter were placed on the outside of a distal femoral locking plate. The adapter converts the slight bending of the plate under axial load into a transverse force which is measurable by the sensor. An osteotomy was created and then plated in the distal femur of biomechanical Sawbones. Specimens were loaded to simulate single-leg stance first with the osteotomy defect empty (acute healing), then sequentially filled with silicone (early callus) and then polymethyl methacrylate (hard callus). There was a strong correlation between applied axial load and force measured by the "smart" plate. Data demonstrate statistically significant differences between each phase of healing with as little as 150 N of axial load applied to the femur. Forces measured in the plate were significantly different between acute (100%), early callus (66.4%), and hard callus (29.5%). This study demonstrates the potential of a "smart" fracture plate to distinguish between phases of healing. These objective data may enable early diagnosis of nonunion and enhance outcomes for patients.

The geriatric distal femur fracture: nail, plate or both?

Surgical fixation of distal femur fractures in geriatric patients is an evolving topic. Unlike hip fractures, treatment strategies for distal femur fractures are ill-defined and lack substantive high-quality evidence. With an increasing incidence and an association with significant morbidity and mortality, it is essential to understand existing treatment options and their supporting evidence. Current fixation methods include the use of either retrograde intramedullary nails, or plate and screw constructs. Due to the variability in fracture patterns, the unique anatomy of the distal femur, and the presence or absence or pre-existing implants, decision-making as to which method to use can be challenging. Recent literature has sought to describe the advantages and disadvantages of each, however, there is currently no consensus on a standard of care, and little randomized evidence is available that directly compares intramedullary nails with plating. Future randomized studies comparing intramedullary nails with plating constructs are necessary in order to develop a standard of care based on injury characteristics.

Nail diameter significantly impacts stability in combined plate-nail constructs used for fixation of supracondylar distal femur fractures

Objectives:

Plate-nail (PN) combinations have been described for fixation of supracondylar distal femur fractures. Small diameter retrograde intramedullary nails (rIMN) are commonly used. The purpose of this study was to investigate the effect of nail diameter on construct stability. We hypothesized that a larger diameter rIMN would not significantly change the stiffness of the PN construct when tested in torsional or axial loading.

Methods:

Twelve synthetic osteoporotic femurs were used to compare nail diameters in an extraarticular supracondylar distal femur fracture model (Orthopaedic Trauma Association/Arbeitsgemeinschaft für Osteosynthesefragen type 33-A3). Constructs were fixed with a 12-hole 4.5 mm pre-contoured lateral distal femoral locking plate combined with either a 9 mm (n = 6) or an 11 mm (n = 6) retrograde intramedullary nail (rIMN). Specimens were cyclically loaded in torsion and axial compression. The primary outcome was construct stiffness, calculated using the average slope of the force-displacement curves.

Results:

The 11 mm PN construct was approximately 1.6 times stiffer than the 9 mm PN construct averaged across all torsional loads (2.39 +/− 0.41 Nm/deg vs 1.44 +/− 0.17 Nm/deg) and approximately 1.3 times stiffer than the 9 mm PN construct averaged across all axial loads (506.84 +/− 44.50 N/mm vs 376.77 +/− 37.65 N/mm). There were no construct failures.

Conclusions:

In this biomechanical model, nail diameter had a significant effect on both torsional and axial stiffness in PN constructs. While the use of smaller diameter rIMNs has been proposed to allow for easier placement of implants, the effect on overall construct stiffness should be considered in the context of the patient, their fracture and desired postoperative weight bearing recommendations.

Level of Evidence: N/A

Boundary Conditions Matter - Impact of Test Setup On Inferred Construct Mechanics in Plated Distal Femur Osteotomies

The mechanics of distal femur fracture fixation has been widely studied in bench tests that employ a variety of approaches for holding and constraining femurs to apply loads. No standard test methods have been adopted for these tests and the impact of test setup on inferred construct mechanics has not been reported. Accordingly, the purpose of this study was to use finite element models to compare the mechanical performance of a supracondylar osteotomy with lateral plating under conditions that replicate several common bench test methods. A literature review was used to define a parameterized virtual model of a plated distal femur osteotomy in axial compression loading with four boundary condition sets ranging from minimally to highly constrained. Axial stiffness, longitudinal motion, and shear motion at the fracture line were recorded for a range of applied loads and bridge spans. The results showed that construct mechanical performance was highly sensitive to boundary conditions imposed by the mechanical test fixtures. Increasing the degrees of constraint, for example by potting and rigidly clamping one or more ends of the specimen, caused up to a 25x increase in axial stiffness of the construct. Shear motion and longitudinal motion at the fracture line, which is an important driver of interfragmentary strain, was also largely influenced by the constraint test setup. These results suggest that caution should be used when comparing reported results between bench tests that use different fixtures and that standardization of testing methods is needed in this field.

Retrograde intramedullary nailing of comminuted intra-articular distal femur fractures results in high union rate

PURPOSE

Retrograde intramedullary nailing of intra-articular distal femur fractures with metaphyseal and/or epiphyseal comminution is controversial and considered a contraindication to nailing. The purpose of this study was to report union rate, complications, and secondary procedures after open reduction and retrograde intramedullary nailing of comminuted, intra-articular, distal femur fractures.

MATERIALS AND METHODS

A retrospective review performed at an urban level one trauma center identified 16 patients AO/Orthopedic Trauma Association (OTA) 33-C2 and 33-C3 femur fractures treated with open reduction, lag screws, and retrograde intramedullary nail fixation. Radiographic union, complications, secondary operations were reviewed.

RESULTS

At the 3-month follow-up 12 (86%) of the 14 patients with radiographs had healed. At last follow-up, all 16 femur fractures achieved radiographic union after the index procedure. No patient required a revision procedure for delayed union or nonunion. Complications occurred in 6 (38%) patients, including failed distal interlocking screws (n = 2), knee arthrofibrosis (n = 3), superficial wound infection (n = 1), and wound dehiscence (n = 1). Three (19%) patients required secondary procedures, which included knee manipulation under anesthesia (n = 3), distal interlocking screw removal (n = 2), and closure of a wound dehiscence (n = 1).

CONCLUSIONS

Comminuted intra-articular distal femur fractures that can be successfully treated with retrograde IMN fixation will reliably go on to union with a complication rate that is favorable to that reported for plate fixation.

LEVEL OF EVIDENCE

Level IV, retrospective case-series.

Incidence of nonunion after surgery of distal femoral fractures using contemporary fixation device: a meta-analysis

PURPOSE

Nonunion is the most frequent cause of reoperation and is associated with high morbidity after distal femur fracture (DFF). We examined the rates of nonunion requiring reoperation after fixation for DFF using a locking compression plate (LCP) or retrograde intramedullary nail (RIMN).

METHODS

We included four studies comparing LCP and RIMN and 38 single-cohort studies reporting LCP or RIMN. In total, 2156 femurs were included and 166 non-unions were detected. We conducted a pair-wise meta-analysis (with a fixed-effects model) on the four comparative studies and a proportional meta-analysis on the 38 articles to estimate the nonunion rate. We performed sensitivity analysis by comparing studies using LCP with less invasive surgical systems (LISS) with those that used RIMN.

RESULTS

The pairwise meta-analysis showed a similar nonunion rate between the groups [odds ratio: 1.02; 95% confidence interval (CI) 0.94-1.11, p = 0.633]. According to proportional meta-analysis, the pooled prevalence of nonunion was 5% (95% CI 4-7) totally, 6% (95% CI 4-8) in the LCP group, and 4% (95% CI 2-6) in the RIMN group (heterogeneity: p = 0.105). According to the sensitivity analysis, there was no difference in the union rate. The pooled prevalence of nonunion from sensitivity analysis was 4 % (95% CI, 3-5); it was 4% (95% CI, 3-6) in LCP with LISS and was 4% (95% CI, 2-6) in RIMN group (heterogeneity: p = 0.941).

CONCLUSION

Approximately 5% of patients who underwent LCP or RIMN fixation developed nonunion. Therefore, LCP and RIMN are effective DFF techniques and mastering one of them is essential.

Excellent outcomes after double-locked plating in very low periprosthetic distal femoral fractures

INTRODUCTION

Very low periprosthetic distal femur fractures (PPDFFs) are rare injuries and often have a relatively high failure rate after single lateral locked plating. The double plating technique yields good outcomes in osteoporotic fractures of the distal femur. To date, there is limited information on double-locked plate fixation of very low PPDFFs. This study aimed to evaluate the outcomes and complications of surgically treated very low PPDFFs using double-locked plate fixation.

MATERIALS AND METHODS

Between January 2013 and December 2018, sixty-one consecutive patients with PPDFFs have been conducted. Only Su type III PPDFFs with double-locked plate fixation through a lateral minimally invasive approach and a medial subvastus approach to the distal femur were analyzed. Patients were encouraged to perform straight leg raising exercises and active knee motion on the second postoperative day. Assisted weight bearing from the early postoperative days was supported, and full weight-bearing was allowed after healing the fracture site. All patients were evaluated according to the time to union, limb alignment, range of knee motion, Knee Society Score, and presence of complications.

RESULTS

Twenty one patients (17 females and 4 males, mean age 76 years, range 56-90) were included in the study. There were 10 of 33-A1, 6 of 33-A2 and 5 of 33 A3 fractures, according to the AO classification. Of 21 patients, 20 achieved union at an average of 14 weeks postoperatively. Postoperative limb alignment was satisfactory in all cases, with an average mechanical distal lateral femur angle of 89° and average mechanical posterior distal femur angle of 86°. All patients recovered the knee joint motion similar to that of the contralateral side, and daily life pre-injury. The average knee and function scores were 94 and 89, respectively. There were one case of non-union and three cases of superficial wound infection, which resolved after intravenous antibiotic therapy.

CONCLUSIONS

Double locked plating showed excellent radiographic and functional outcomes with few complications in patients with very low PPDFFs. Based on these promising results, we propose the consideration of double-locked plate fixation in the treatment of very low PPDFFs.

Comparative analysis of the biomechanical behavior of anterograde/retrograde nailing in supracondylar femoral fractures

Supracondylar femoral fractures account for a noticeable percentage of the femoral shaft fractures, affecting two etiological groups: high energy trauma in young men, with good bone quality, and older women with osteoporotic femur. Surgical treatment of those kind of fractures remains controversial, with different surgical options such as plate and sliding barrel locking condylar plate, less invasive stabilization system (LISS) or intramedullary nailing, which has emerged as a new fixation choice in the treatment of that type of fractures. The present work performs a comparative study about the biomechanical behavior of anterograde and retrograde nailing in supracondylar femoral fractures type A, in order to determine the best choice of nailing and locking configuration. A three-dimensional finite element model of the femur was developed, modeling femoral supracondylar fracture and different nailing configurations, both for anterograde and retrograde nails. The study was focused on the immediately post-operative stage, verifying the appropriate stability of the osteosynthesis. The obtained results show a better biomechanical behavior for anterograde nails, providing a better stability from the point of view of global movements, lower stresses in screws, and less stress concentration in cortical bone. So, for the analyzed fractures and osteosyntheses types, anterograde nailing has demonstrated to be a better surgical option, being an excellent indication in supracondylar fractures of femur, with clear benefits compared to retrograde nailing, providing a better stabilization which enables for a more satisfactory fracture healing.

Plate-on-plate technique for treating peri-implant fractures of distal femoral locking plate: a retrospective study of 11 patients

INTRODUCTION

In this study, we aimed to ascertain the feasibility and reliability of the plate-on-plate technique for peri-implant fractures of the distal femoral locking plate when the distal femoral fracture is still unhealed.

MATERIALS AND METHODS

From January 2007 to December 2016, we enrolled 11 patients who received treatment at our institution. All patients underwent at least 1 year of follow-up. Their medical records, imaging studies, visual analogue scores, walking ability, complications, and functional outcomes at 1 year postoperative based on the Short Form (36) Health Survey (SF-36) scores were retrospectively evaluated.

RESULTS

The average follow-up duration was 20.5 (range 15-30) months. All fractures united with satisfactory alignment, and the average time for union was 27.5 (range 16-40) weeks. The average SF-36 scores at 1 year postoperative was 79.2 (range 72-90). Regarding ambulatory status, all patients could perform unrestricted outdoor ambulation.

CONCLUSION

In our case series, the plate-on-plate technique achieved a good bone union rate and functional outcomes with low complication rates and thus may be a good alternative for managing this difficult type of fracture.

Locking plate fixation versus antegrade intramedullary nailing for the treatment of extra-articular distal femoral fractures

INTRODUCTION

The current study aimed to retrospectively analyze locked plating (LP) and antegrade intramedullary nailing (AIN) for the treatment of extra-articular distal femoral fractures.

PATIENTS AND METHODS

Between January 2000 and March 2015, 97 patients (49 male, 48 female) underwent surgery for extra-articular distal femoral fractures in our clinic. Patients were grouped based on their method of treatment (69 (71.1%) with locked plate (LP group) and 28 (28.9%) with antegrade intramedullary nailing (AIN group)), and the groups were analyzed with regards to fracture types, associated trauma, hospital stay, Injury Severity Score (ISS), nonunion, reoperation rate and Lysholm Functional Knee Score.

RESULTS

The LP and AIN groups had no significant differences with regards to age and gender. Sixteen patients (16.4%) experienced nonunion; all of these (5 (5.1%) in the AIN group and 11 (11.3%) in the LP group) required a secondary procedure (p = 0.773). ISS was significantly higher in the AIN group (p = 0.033). There were no significant differences between the two groups with regards to hardware failure, postoperative malreduction, reoperation rate, deep infection, and nonunion. However, the AIN group (mean 88) had a significantly higher Lysholm Functional Knee Score than the LP group (mean 75.9) (p = 0.019).

CONCLUSION

In our study we encountered less nonunion in AIN group. Both fixation methods offer good results; however, functional outcomes in the AIN group were significantly better than those in the LP group.

A surgical algorithm for the management of recalcitrant distal femur nonunions based on distal femoral bone stock, fracture alignment, medial void, and stability of fixation

BACKGROUND

Recalcitrant distal femur nonunions (RDFN) are a challenge in management due to factors including poor bone stock, multiple surgeries, metaphyseal bone loss, and joint contractures. There are no specific guidelines in the management of cases of RDFN. Based on our experience, we devised an algorithm and we present the results of 62 cases of RDFN managed following it.

MATERIALS AND METHODS

Our algorithm was formulated after analyzing 34 cases of RDFN and it involved four factors which were hypothesized to influence outcomes namely: distal femoral bone stock, extent of medial void, alignment of the fracture, and stability of fixation. Each factor was addressed specifically to achieve a good outcome. Between 2012 and 2015, 62 patients with RDFN at a mean age of 47.4 years (26-73) and 2.3 prior surgeries (2-6) were managed following the algorithm.

INTERVENTION

58 patients required revision osteosynthesis to improve alignment and achieve a stable fixation. 4 elderly patients with poor bone stock were managed with arthroplasty. Extent of medial void was found to significantly influence surgical decision making. Five patients without medial void required only cancellous autograft bone grafting, 47 patients with < 2 cm void were treated with an allograft fibular strut inserted in the metaphysis and 6 patients with a void > 2 cm were managed with medial plating.

OUTCOMES AND RESULTS

57 patients treated with osteosynthesis achieved union at an average of 7.4 months (6-11) and the 4 patients managed with arthroplasty also had a favourable outcome. One patient who was managed with revision osteosynthesis had a nonunion with an implant failure and needed an arthroplasty procedure. The average LEFS (lower extremity functional score) of all our patients was 67 (51-76) at an average follow-up of 18.2 months (12-33).

CONCLUSION

Our stepwise surgical algorithm would help surgeons to identify the factors that need to be addressed and guide them towards the interventions that are necessary to achieve a successful outcome while managing cases of RDFN.

LEVEL OF EVIDENCE

III.

LEVEL OF CLINICAL CARE

Level I Tertiary trauma centre.

Mechanical characterization of bone quality in distal femur fractures using pre-operative computed tomography scans

BACKGROUND

Mechanical testing of implant constructs designed to treat distal femur fractures has been hampered by a lack of clinical data on the biomechanical properties of the distal femur in patients who sustain these fractures. Therefore, the purpose of this study was to use quantitative computed tomography (qCT) to investigate the mechanical characteristics of fractured distal femurs to inform the selection of synthetic materials for biomechanical testing.

METHODS

Distal femur fractures treated at a Level I trauma center were retrospectively reviewed and 43 cases with preoperative CT scans were identified for analysis. Scans were segmented and each bone fragment was reconstructed as a 3D model. The Young's modulus of the distal femur was determined from voxel-based radiodensity.

FINDINGS

Median patient age was 72 years (IQR = 57-81), with 26% males and 74% females. Young's modulus in the distal femur was negatively correlated with patient age (R² = 0.50, p < 0.001). The distribution of patient-specific modulus values was also compared with the compressive modulus ranges for graded polyurethane foams according to ASTM F1839. Bone quality ranged from Grade 25 in younger individuals to Grade 5 in older individuals.

CONCLUSION

No single grade of synthetic polyurethane foam can be selected to model all clinically important scenarios for biomechanical testing of distal femur fracture fixation devices. Rather, this data can be used to select an appropriate material for a given clinical scenario. A Grade 25 foam is appropriate for implant longevity, whereas for implant stability, Grades 5-15 are more appropriate.

Comparison of Less Invasive Stabilization System Plate and Retrograde Intramedullary Nail in the Fixation of Femoral Supracondylar Fractures in the Elderly: A Biomechanical Study

Objective

To compare the biomechanical stabilities of less invasive stabilization system (LISS) plate and retrograde intramedullary nail (IMN) for the comminuted femoral supracondylar fracture fractures in the elderly.

Methods

Sixteen pairs of embalmed cadaver femurs were obtained to simulate a comminuted supracondylar femur fracture (AO/OTA33‐A3) gap model. All left‐side specimens were fixed with LISS plate, and retrograde IMN were applied to the right‐side specimens. All specimens were tested in torsional, axial and cyclic load mode on an Instron testing machine.

Results

The mean torsional stiffness for LISS plate group was 34.1% greater than retrograde IMN group (2.90 vs. 1.91 Nm/degree, P = 0.002), but the mean axial stiffness was greater for the retrograde IMN (199.16 vs. 303.93 N/mm, P < 0.001). The total deformation of LISS plate caused by cyclic axial loading was greater than retrograde IMN (4.17 vs. 3.57 mm, P = 0.014). Significantly less mean irreversible deformation was detected in LISS plate than in retrograde IMN (1.64 vs. 1.69 mm, P = 0.699). Failure loads of the constructs were significantly different between the two groups (LISS plate: 2941±128 N; retrograde IMN: 4022±176 N, P < 0.001).

Conclusion

For comminuted femoral supracondylar fractures in the elderly, the tested instruments can both maintain sufficient biomechanical stabilities, but retrograde IMN is superior to LISS plate in deformation of fracture site.

Strength⁻Durability Correlation of Osteosynthesis Devices Made by 3D Layer Manufacturing

To develop orthopedic implants that are optimized for each patient’s needs or skeletal structure (custom-made implants), evaluations of the bending strength, bending stiffness, and durability of various types of conventional osteosynthesis devices have become important. Four-point bending tests and compression bending tests of osteosynthesis devices (bone plates, intramedullary nail rods, spinal rods, compression hip screws (CHSs), short femoral nails, and metaphyseal plates) were carried out to measure their bending stiffness, bending strength, and durability. The bending stiffness of bone plates, intramedullary nails, spinal rods, CHSs, short femoral nails, and metaphyseal plates increased with increasing bending strength. The durability limit of various types of osteosynthesis devices linearly increased with increasing bending strength. The relationship (durability limit at 10⁶ cycles) = 0.67 × (bending strength) (N·m) (R² = 0.85) was obtained by regression. The relationship for the highly biocompatible Ti-15Zr-4Nb-4Ta alloy was also linear. The mechanical strength and ductility of specimens that were cut from various osteosynthesis devices were excellent and their microstructures consisted of fine structures, which were considered to be related to the excellent durability. These results are expected to be useful for the development of implants suitable for the skeletal structure of patients using three-dimensional (3D) layer manufacturing technologies.

[Current status and progress of clinical research on distal femoral fractures]

Objective

To investigate current status and latest progress of clinical research on distal femoral fractures.

Methods

The related literature was extensively reviewed to summarize the trend of the researches and their clinical application in the treatment of distal femoral fractures.

Results

Distal femoral fractures are likely to occur in young people who suffer from high-energy damage and the elderly with osteoporosis, which is always comminuted and unstable fractures, and often involved in the articular surface and combined with serious soft tissue injury. Therefore, the treatment faces many challenges. External fixation is now used as a temporary means of controlling injury. The vast majority of patients are feasible to internal fixation, including plates system and intramedullary nail system. Different internal fixator also has its own characteristics, such as double plates can strengthen the medial support of the femur, less invasive stabilization system protects the blood supply of fractures, distal cortial locking plate is theoretically more fit for the requirements of bone healing, retrograde intramedullary nail can resist varus and valgus.

Conclusion

The treatment of distal femoral fractures should be based on the type of fracture and the characteristics of internal fixators.

The antegrade angle-stable locking intramedullary nail for type-C distal femoral fractures: a thirty four case experience

INTRODUCTION

This is a retrospective study that provides initial experience and verifies the effectiveness of the newly-designed antegrade interlocking angle-stable intramedullary nail (IAIN) combined with half-threaded cancellous screws in the management of type-C (AO/OTA classification) distal femoral fractures.

METHODS

During a period of 30 months, 34 patients (mean age 43.1 years) with type-C (AO/OTA classification) fractures of the distal femur were treated with IAIN and half-threaded cancellous screws were reviewed. Peri-operative and post-operative parameters were analyzed.

RESULTS

All of the fractures healed in a mean time of 12.6 weeks with no incidences of malunion, nonunion or infection. No secondary failure of fixation occurred. Partial weight bearing was initiated in an average of 7.4 weeks post-operatively, with full weight bearing initiated in 13.8 weeks. All of the patients, except for one, gained full extension. The mean flexion of the knee joint was 110.1°, while the mean Hospital for Special Surgery (HSS) knee score was 85.2.

CONCLUSION

The IAIN and half-threaded cancellous screws provided a reliable fixation that facilitated uncomplicated outcomes and uneventful early mobilization in treating type-C fractures of the distal femur.

‘Modern’ distal femoral locking plates allow safe, early weight-bearing with a high rate of union and low rate of failure

Aims

Fractures of the distal femur can be challenging to manage and are on the increase in the elderly osteoporotic population. Management with casting or bracing can unacceptably limit a patient’s ability to bear weight, but historically, operative fixation has been associated with a high rate of re-operation. In this study, we describe the outcomes of fixation using modern implants within a strategy of early return to function.

Patients and Methods

All patients treated at our centre with lateral distal femoral locking plates (LDFLP) between 2009 and 2014 were identified. Fracture classification and operative information including weight-bearing status, rates of union, re-operation, failure of implants and mortality rate, were recorded.

Results

A total of 127 fractures were identified in 122 patients. The mean age was 72.8 years (16 to 101) and 92 of the patients (75%) were female. A consultant performed the operation in 85 of the cases, (67%) with the remainder performed under direct consultant supervision. In total 107 patients (84%) were allowed to bear full weight immediately. The rate of clinical and radiological union was 81/85 (95%) and only four fractures of 127 (3%) fractures required re-operation for failure of surgery. The 30-day, three- and 12-month mortality rates were 6 (5%), 17 (15%) and 25 (22%), respectively.

Conclusion

Our study suggests an exponential increase in the incidence of a fracture of the distal femur with age, analogous to the population suffering from a proximal femoral fracture. Allowing immediate unrestricted weight-bearing after LDFLP fixation in these elderly patients was not associated with failure of fixation. There was a high rate of union and low rate of re-operation. Cite this article: Bone Joint J 2017;99-B:951–7.

A 3 year minimum follow up of Endoprosthetic replacement for distal femoral fractures - An alternative treatment option

INTRODUCTION

Although the use of an endoprosthesis for distal femoral fractures remains a valid treatment option the widespread use is in its infancy.

METHODOLOGY

In this retrospective case series, we review cases of distal femoral fracture treated with endoprosthetic replacement (EPR). The outcomes we assessed were the time to start mobilising, the time to discharge, morbidity and mortality as well as an Oxford knee score to assess pain and function and also the early survivorship. 6 of the 11 from the cohort had existing Total Knee Replacements (TKRs) in situ.

RESULTS

There were 11 knees in our cohort with a mean age of 81.5 years (range 52-102 years). The median time to follow up was 3.5 years (range 1.6 to 5.5 years). The median times to theatre was 3 days and to discharge was 16 days. Oxford functional and pain scores were 32/48.

DISCUSSION

In the appropriate patient and fracture pattern, Endoprosthetic knee replacement is an excellent option in the treatment of distal femoral fractures whether associated with an existing TKR or not. The implant is more costly than traditional open reduction and internal fixation, but the earlier return to full mobility post-operatively may save on hospital/care home stay and free up hospital space and minimise complications.

Comminuted supracondylar femoral fractures: a biomechanical analysis comparing the stability of medial versus lateral plating in axial loading

The aim of this study was to compare the biomechanical properties of medial and lateral plating of a medially comminuted supracondylar femoral fracture. A supracondylar femoral fracture model comparing two fixation methods was tested cyclically in axial loading. One-centimetre supracondylar gap osteotomies were created in six synthetic femurs approximately 6 cm proximal to the knee joint. There were two constructs investigated: group 1 and group 2 were stabilized with an 8-hole LC-DCP, medially and laterally, respectively. Both construct groups were axially loaded. Global displacement (total length), wedge displacement, bending moment and strain were measured. Medial plating showed a significantly decreased displacement, bending moment and strain at the fracture site in axial loading. Medial plating of a comminuted supracondylar femur fracture is more stable than lateral plating.

Comparison of supraintercondylar and supracondylar femur fractures treated with condylar buttress plates

Background

Treatment of supraintercondylar (AO/OTA 33-C) and supracondylar (AO/OTA 33-A) femur fractures is generally challenging. Standard treatments include open reduction and internal fixation. However, optimal implants are now being well-defined. This study focus on the comparison between clinical and functional outcomes of fractures treated with condylar buttress plates (CBPs).

Methods

We treated 87 patients with supraintercondylar or supracondylar femur fracture from 2004 to 2008, including 30 supraintercondylar and 24 supracondylar fractures treated with CBPs. Both knee and function scores (per Knee Society) were given to clinical and functional outcomes, and concomitant knee function was assessed per Mize criteria.

Results

Union rate of supraintercondylar fractures was 90 % (27/30) and supracondylar fractures was 91.7 % (22/24) (P = 0.68). In supraintercondylar group, 16.7 % revealed postoperative varus deformity, whereas none in supracondylar group (P = 0.045). Knee Society knee score was 73.6 in supraintercondylar group and 85.5 in supracondylar group (P = 0.009); and function score was 62.5 in supraintercondylar group and 83.1 in supracondylar group (P = 0.023). A satisfactory result based on modified Mize criteria was achieved in 50 % of supraintercondylar fractures and in 79.1 % of supracondylar fractures (P = 0.09).

Conclusions

Use of CBPs for supraintercondylar and supracondylar femur fractures treatment led to a high union rate. However, a high rate of varus deformity occurred in patients with supraintercondylar but not supracondylar fractures. Moreover, CBP treatment in patients with supracondylar fractures led to better functional outcomes than those with supraintercondylar fractures.

Modified fixations for distal femur fractures following total knee arthroplasty: a biomechanical and clinical relevance study

PURPOSE

Distal femur fractures adjacent to total knee arthroplasty are a rare yet complex problem. Recently, extramedullary locking plate and retrograde intramedullary nail fixations have become popular options, but the complication rates associated with these procedures are 15-20 %. Modified fixations were assessed in an effort to reduce complications from unstable periprosthetic fractures.

METHODS

Using experimental and finite element methods, this study compared the construct behaviours of a locking plate, a retrograde intramedullary nail, and their modifications (a spiral-blade supplemented in an intramedullary nail or a locking plate/allograft hybrid) when subjected to various fracture types, locations, loading conditions, and bony strength. The implanted models were used to assess construct stiffness, fracture micromotion, and implant stress under different osteoporotic conditions. Finally, we collected 40 cases for radiological analysis to indicate the appropriate procedure for treating periprosthetic fractures following total knee arthroplasty.

RESULTS

Regardless of the fracture type, femoral constructs fixed with a conventional or spiral-blade supplemented intramedullary nail exhibited higher axial but lower torsional stiffness than those fixed with a locking plate. Torsional deformation occurred if the lower-positioned fracture had no medial support. The locking plate/allograft construct exhibited the highest stiffness and the least micromotion. A review of 40 clinical cases confirmed the above findings regarding the locking plate/allograft construct.

CONCLUSION

The spiral-blade supplement of retrograde intramedullary nail and locking plate/allograft modified constructs significantly stabilizes the unstable fractured gaps. The locking plate/allograft is recommended for the periprosthetic fractures with deficient bone stock and severe osteoporosis to improve alignment and healing potentials.

Management principles of osteoporotic fractures

Osteoporotic fractures are difficult to manage. They pose a number of difficulties to the surgeon arising from the underlying poor bone stock compromising the intention to achieve optimum fixation. Moreover, the frail elderly patients present with a variety of medical co-morbidities increasing the risk of developing perioperative complications. Despite these recognized challenges, there are currently a number of improving technologies and strategies at the surgeon's disposal to provide more confidence with fracture fixation and maximize the chance of success.

Preliminary testing of a novel bilateral plating technique for treating periprosthetic fractures of the distal femur

BACKGROUND

Current stabilization methods for periprosthetic fractures of the distal femur are inadequate in achieving fracture fixation, with complication rates as high as 29%. A major contributor to poor outcomes is that these methods rely only on screw purchase in the bone to maintain fracture reduction. We designed, manufactured and evaluated a novel plating method that utilizes the femoral prosthesis to enhance stability for treatment of distal femoral periprosthetic fractures.

METHODS

Medial and lateral plates were designed and manufactured based on geometry of a synthetic femur and femoral prosthesis. The two plates were linked via a compression screw and a small tab on each plate that inserted into pre-existing slots on the prosthesis. Mechanical tests (500N compression or 250N anterior directed cantilever bending), were performed on synthetic femurs with simple transverse fractures (3mm gap) just superior to the distal femoral prosthesis that were stabilized using either the prototype plates or a single lateral plate. Translational movements of the fracture site during loading were measured using 3D motion tracking.

FINDINGS

With the single lateral plate, the distal fragment experienced a resultant displacement of 0.40mm under cantilever bending and 0.61mm under compression (13% and 20% respectively of fracture gap width). With the bilateral plates, fracture gap motion was significantly reduced to 0.13mm under bending and compression (4.3% of the fracture gap).

INTERPRETATION

Our results indicate that a bilateral plating method is capable of improving stabilization of periprosthetic fractures compared to the traditional lateral plating technique.

Periarticular Fractures of the Knee in Polytrauma Patients

Periarticular fractures around the knee are a challenge for the orthopaedic surgeon. When these fractures are presented in the context of a multiple trauma patient, they are even more difficult to manage because the treatment approach depends not only on the fracture itself, but also on the patient's general condition. These fractures, caused by high-energy trauma, present complex fracture patterns with severe comminution and major loss of articular congruity, and are often associated with vascular and nerve complications, particularly in the proximal tibia, due to its anatomical features with poor myocutaneous coverage. They are almost always accompanied by soft tissue injury. The management of polytrauma patients requires a multidisciplinary team and accurate systemic stabilization of the patient before undertaking orthopaedic treatment. These fractures are usually addressed sequentially, either according to the general condition of the patient or to the local characteristics of the lesions. In recent decades, various fixation methods have been proposed, but there is still no consensus as to the ideal method for stabilizing these fractures. In this paper, we describe the general characteristics of these fractures, the stabilization methods traditionally used and those that have been developed in recent years, and discuss the treatment sequences proposed as most suitable for the management of these injuries.

Distal femoral fractures in the elderly: biomechanical analysis of a polyaxial angle-stable locking plate versus a retrograde intramedullary nail in a human cadaveric bone model

INTRODUCTION

Compromised bone quality and the need for early mobilization still lead to high rates of implant failure in geriatric patients with distal femoral fractures. With the newest generation of polyaxial locking plates and the proven retrograde femoral nails today two minimally invasive surgical procedures have been established. Indications for both procedures overlap. This study attempts to define the strength and failure mode of both surgical procedures.

MATERIALS AND METHODS

A standardized fracture model was established to simulate an unstable AO/OTA 33-A3 fracture. Eight pairs of human cadaver femora (mean age 79 years, range 63-100 years) with compromised bone quality were used. Osteosyntheses with eight retrograde femoral nails and eight locking plates were randomly performed. A materials testing machine (Instron 5566) was used to perform cyclic stress tests according to a standardized loading protocol, up to a maximum load of 5,000 N.

RESULTS

All specimens survived loading of at least 2,500 N. Three nail and one plate construct survived a maximum load of 5,000 N. The mean compressive force leading to failure was 4,400 N (CI 4,122-4,678 N) for nail osteosynthesis and 4,429 N (CI 3,653-5,204 N) for plate osteosynthesis (p = 0.943). Proximal cutting out of the osteosynthesis was the most common reason for interruption in the nail and plate osteosyntheses. Significant differences between the retrograde femoral nail and plate osteosyntheses were seen under testing conditions for plastic deformation and stiffness of the constructs (p = 0.002 and p = 0.001, respectively).

CONCLUSION

Based on our results, no statements regarding the superiority of either of the devices can be made. Even though the load to failure values for both osteosyntheses were much higher than the loads experienced during normal walking; however, because only axial loading was applied, it remains unclear whether both osteosyntheses meet the estimated requirements for postoperative full weight-bearing for an average heavy patient with a distal femoral fracture.

Mono- versus polyaxial locking plates in distal femur fractures - a biomechanical comparison of the Non-Contact-Bridging- (NCB) and the PERILOC-plate

Background

The aim of this cadaveric study was to compare a polyaxial (NCB®, Zimmer) to a fixed-angle monoaxial locking plate (PERILOC®, Smith & Nephew) in comminuted fractures of the distal femur regarding stability of the construct. Up to date there is no published biomechanical data concerning polyaxial plating in cadaveric distal femurs.

Methods

Fourteen formalin fixed femora were scanned by dual-energy x-ray absorptiometry. As fracture model an unstable supracondylar comminuted fracture was simulated. Fractures were pairwise randomly fixed either with a mono- (group A) or a polyaxial (group B) distal femur plate. The samples were tested in a servohydraulic mechanical testing system starting with an axial loading of 200 N following an increase of 200 N in every step with 500 cycles in every sequence up to a maximum of 2 000 N. The end points were implant failure or relevant loss of reduction. Data records included for each specimen time, number of cycles, axial load and axial displacement. Statistical analysis was performed using the exact Wilcoxon signed rank test.

Results

The mean donor age at the time of death was 75 years. The bone mass density (BMD) of the femurs in both groups was comparable and showed no statistically significant differences. Five bones failed before reaching the maximum applied force of 2000 N. Distribution curves of all samples in both groups, showing the plastic deformation in relation to the axial force, showed no statistically significant differences.

Conclusions

Operative stabilization of distal femur fractures can be successfully and equally well achieved using either a monoaxial or a polyaxial locking plate. Polyaxial screw fixation may have advantages if intramedullary implants are present.

Electronic supplementary material

The online version of this article (doi:10.1186/1471-2474-15-369) contains supplementary material, which is available to authorized users.

Biomechanical analysis of distal femoral fracture fixation: dynamic condylar screw versus locked compression plate

BACKGROUND

This human cadaveric study i ntroduces a laboratory model to establish and compare the fixation stability of the distal femoral locking plate (DFLP) and dynamic condylar screw (DCS) in distal femoral fracture fixation.

MATERIALS AND METHODS

The study was conducted on 16 fresh cadaveric femoral specimens, 8 implanted with the DCS and the other 8 with the DFLP. The construct was made unstable by removing a standard-sized medial wedge with a 1-cm base (gap osteotomy) beginning 6 cm proximal to the lateral joint line in the distal metaphyseal region with loss of the medial buttress. Each specimen underwent axial and torsional stiffness testing along with cyclic axial loading to failure. The mean DEXA value for the DFLP group was 0.82 g/cm(2) and in the DCS group was 0.79 g/cm(2).

RESULTS

Axial stiffness in the DFLP group was significantly higher than in the DCS group, but no significant difference was found in torsional stiffness between the groups. A significant difference was found in the load-to-failure results between the groups. Plastic and total deformation was significantly higher in constructs in the DCS group than in those in the DFLP group. Total energy absorbed before construct failure was also significantly higher in the DFLP group than in the DCS group.

CONCLUSIONS

The DFLP construct proved stronger than the DCS in both axial stiffness and cyclic loading, but similar in torsional stiffness in biomechanical testing in a simulated A3 distal femoral fracture.

Biomechanical testing of distal femur osteotomy plate fixation techniques: the role of simulated physiological loading

BACKGROUND

Implants for fracture and/or osteotomy fixation are often tested according to basic mechanical test models such as open gap tests or 4-point-bending tests. These may be suitable to test and compare different implants for safety and clinical approval, but are not always representative of the post-operative situation, which is decisive when it comes to bone healing. In the current study the Knee Expert Group of the Association for the Study of Internal Fixation has compared the available open gap test results of the latest version of the TomoFix Medial Distal Femoral Plate and the antecedent plate design, with the test results of a more physiological and life-like test model. In the open gap test model the antecedent plate design was found to have superior stiffness and fatigue strength.

METHODS

In the current study simulated postoperative conditions for medial closing wedge supracondylar osteotomies were used. The constructs were subjected to cyclical axial and torsional loading and were subsequently tested to failure.

RESULTS

The more life-like tests in this study showed that the latest version was either more or equally stable and stiff than the antecedent version of the plate, in all of the tests. It is argued that the difference in results between the two loading models is due to differences in test design.

CONCLUSIONS

These test results stress the importance of not only using standard open gap and 4-point-bending tests, but also to use as life-like as possible test conditions for any form of biomechanical testing of new implants.

Do elderly patients fare worse following operative treatment of distal femur fractures using modern techniques?

BACKGROUND

The purpose of this study was to compare the functional outcomes and quality of life of older and younger patients with similarly treated distal femur fractures.

METHODS

We conducted an assessment of 57 patients who sustained distal femur fractures (Orthopaedic Trauma Association Type 33B, C) and underwent surgical treatment at our academic medical center. Patients were divided into 2 groups for analysis: an elderly cohort of patients aged 65 or older and a comparison cohort of patients younger than age of 65. A retrospective review of demographics, preoperative ambulatory status, radiographic data, and physical examination data was collected from the medical records. Follow-up functional data were collected via telephone at a mean of 2.5 years (range 6 months-8 years) using a Short Musculoskeletal Functional Assessment (SMFA). All patients underwent standard operative treatment of either nail or plate fixation.

RESULTS

There was no statistical difference in gender, fracture type, surgical technique, surgeon, or institution where the surgery was performed. The percentage of patients with healed fractures at 6-months follow-up was not significantly different between the cohorts. The elderly cohort had slightly worse knee range of motion at 3, 6, and 12 months postoperatively but there was not a statistically significant difference between the groups. The SMFA Daily Activity, Functional, and Bother indices were significantly worse in the older cohort (P < .01, P = .01, P = .02, respectively). However, there was no significant difference in the SMFA Emotional or Mobility indices.

CONCLUSION

Despite lower quality of life and functional scores, this study suggests that relatively good clinical outcomes can be achieved with surgical fixation of distal femoral fractures in the elderly patients. Age should not be used as a determinate in deciding against operative treatment of distal femur fractures in the elderly patients.

Retrograde intramedullary nails with distal screws locked to the nail have higher fatigue strength than locking plates in the treatment of supracondylar femoral fractures

We investigated a new intramedullary locking nail that allows the distal interlocking screws to be locked to the nail. We compared fixation using this new implant with fixation using either a conventional nail or a locking plate in a laboratory simulation of an osteoporotic fracture of the distal femur. A total of 15 human cadaver femora were used to simulate an AO 33-A3 fracture pattern. Paired specimens compared fixation using either a locking or non-locking retrograde nail, and using either a locking retrograde nail or a locking plate. The constructs underwent cyclical loading to simulate single-leg stance up to 125 000 cycles. Axial and torsional stiffness and displacement, cycles to failure and modes of failure were recorded for each specimen. When compared with locking plate constructs, locking nail constructs had significantly longer mean fatigue life (75 800 cycles (sd 33 900) vs 12 800 cycles (sd 6100); p = 0.007) and mean axial stiffness (220 N/mm (sd 80) vs 70 N/mm (sd 18); p = 0.005), but lower mean torsional stiffness (2.5 Nm/° (sd 0.9) vs 5.1 Nm/° (sd 1.5); p = 0.008). In addition, in the nail group the mode of failure was either cut-out of the distal screws or breakage of nails, and in the locking plate group breakage of the plate was always the mode of failure. Locking nail constructs had significantly longer mean fatigue life than non-locking nail constructs (78 900 cycles (sd 25 600) vs 52 400 cycles (sd 22 500); p = 0.04).

The new locking retrograde femoral nail showed better stiffness and fatigue life than locking plates, and superior fatigue life to non-locking nails, which may be advantageous in elderly patients.

Cite this article: Bone Joint J 2014;96-B:114–21.

Finite element comparison of retrograde intramedullary nailing and locking plate fixation with/without an intramedullary allograft for distal femur fracture following total knee arthroplasty

PURPOSE

Periprosthetic distal femur fracture after total knee arthroplasty due to the stress-shielding phenomenon is a challenging problem. Retrograde intramedullary nail (RIMN) or locking plate (LP) fixation with/without a strut allograft has been clinically used via less invasive stabilization surgery (LISS) for the treatment of these periprosthetic fractures. However, their biomechanical differences in construct stability and implant stress have not been extensively studied, especially for the osteoporotic femur.

METHODS

This study used a finite-element method to evaluate the differences between RIMN, LP, and LP/allograft fixation in treating periprosthetic distal femur fractures. There were sixteen variations of two fracture angles (transverse and oblique), two loading conditions (compression and rotation), and four bony conditions (one normal and three osteoporotic). Construct stiffness, fracture micromotion, and implant stress were chosen as the comparison indices.

RESULTS

The LP/allograft construct provides both lateral and middle supports to the displaced femur. Comparatively, the LP and RIMN constructs, respectively, transmit the loads through the lateral and middle paths, thus providing more unstable support to the construct and high stressing on the implants. The fracture pattern plays a minor role in the construct stabilization of the three implants. In general, the biomechanical performances of the RIMN and LP constructs were comparable and significantly inferior to those of the LP/allograft construct. The bone quality should be evaluated prior to the selection of internal fixators.

CONCLUSIONS

The LP/allograft construct significantly stabilizes the fracture gap, reduces the implant stress, and serves as the recommended fixation for periprosthetic distal femur fracture.

In vitro comparison of resistance to implant failure in unstable trochanteric fractures fixed with intramedullary single screw versus double screw device

BACKGROUND

The purpose of this study was to compare the resistance of intramedullary single screw device (Gamma nail) and double screw device proximal femoral nail (PFN) in unstable trochanteric fractures in terms of the number of cycles sustained, subsidence and implant failure in an axial loading test in cadaveric femora.

MATERIALS AND METHODS

The study was conducted on 18 dry cadaveric femoral specimens, 9 of these were implanted with a Gamma nail and 9 with PFN. There was no significant difference found in average dual energy X-ray absorptiometry value between both groups. The construct was made unstable (AO type 31A3.3) by removing a standard sized posteromedial wedge. These were tested on a cyclic physiological loading machine at 1 cycle/s with a load of 200 kg. The test was observed for 50,000 loading cycles or until implant failure, whichever occurred earlier. Peak displacements were measured and analysis was done to determine construct stiffness and gap micromotion in axial loading.

RESULT

It was observed that there was statistically significant difference in terms of displacement at the fracture gap and overall construct stiffness of specimens of both groups. PFN construct group showed a mean subsidence of 1.02 mm and Gamma nail construct group showed mean subsidence of 2.36 mm after cycling. The average stiffness of Gamma nail group was 62.8 ± 8.4 N/mm which was significantly lower than average stiffness of the PFN group (80.4 ± 5.9 N/mm) (P = 0.03). In fatigue testing, 1 out of 9 PFN bone construct failed, while 5 of 9 Gamma nail bone construct failed.

CONCLUSION

When considering micromotion (subsidence) and incidence of implant/screw failure, double screw device (PFN) had statistically significant lower micromotion across the fracture gap with axial compression and lower incidence of implant failure. Hence, double screw device (PFN) construct had higher stability compared to single screw device (GN) in an unstable trochanteric fracture femur model.

Biomechanical comparison of locked plating and spiral blade retrograde nailing of supracondylar femur fractures

OBJECTIVE

Biomechanical comparison between locked plating and retrograde nailing of supracondylar femur fractures with simulated postoperative weight-bearing.

METHODS

The Locking Condylar Plate (LCP) and Retrograde/Antegrade EX Femoral Nail (RAFN) were tested using 10 paired elderly cadaveric femurs, divided into Normal and Low Bone Mineral Density (BMD) groups, with a simulated AO/OTA type 33-A3 supracondylar femur fracture. Each specimen was subjected to 200,000 loading cycles in an attempt to simulate six weeks of postoperative recovery with full weight-bearing for an average individual. The construct's subsidence due to cyclic loading, and axial stiffness before and after the cyclic loading were measured and their correlation with BMD was studied. The two implants were compared in a paired study within each BMD group.

RESULTS

LCP constructs showed higher axial stiffness compared to RAFN for both Normal and Low BMD groups (80% and 57%, respectively). After cyclic loading, axial stiffness of both constructs decreased by 20% and RAFN constructs resulted in twice as much subsidence (1.9 ± 0.6mm). Two RAFN constructs with Low BMD failed after a few cycles whereas the matched pairs fixed with LCP failed after 70,000 cycles.

CONCLUSIONS

The RAFN constructs experienced greater subsidence and reduced axial stiffness compared to the LCP constructs. In Low BMD specimens, the RAFN constructs had a higher risk of failure.

Blocking screws for the treatment of distal femur fractures

Intramedullary nailing is one of the most convenient biological options for treating distal femoral fractures. Because the distal medulla of the femur is wider than the middle diaphysis and intramedullary nails cannot completely fill the intramedullary canal, intramedullary nailing of distal femoral fractures can be difficult when trying to obtain adequate reduction. Some different methods exist for achieving reduction. The purpose of this study was determine whether the use of blocking screws resolves varus or valgus and translation and recurvatum deformities, which can be encountered in antegrade and retrograde intramedullary nailing. Thirty-four patients with distal femoral fractures underwent intramedullary nailing between January 2005 and June 2011. Fifteen patients treated by intramedullary nailing and blocking screws were included in the study. Six patients had distal diaphyseal fractures and 9 had distal diaphyseo-metaphyseal fractures. Antegrade nailing was performed in 7 patients and retrograde nailing was performed in 8. Reduction during surgery and union during follow-up were achieved in all patients with no significant complications. Mean follow-up was 26.6 months. Mean time to union was 12.6 weeks. The main purpose of using blocking screws is to achieve reduction, but they are also useful for maintaining permanent reduction. When inserting blocking screws, the screws must be placed 1 to 3 cm away from the fracture line to avoid from propagation of the fracture. When applied properly and in an adequate way, blocking screws provide an efficient solution for deformities encountered during intramedullary nailing of distal femur fractures.

Biomechanical comparison of dynamic condylar screw and locking compression plate fixation in unstable distal femoral fractures: An in vitro study

BACKGROUND

Distal femur fractures are difficult to manage and the selection of implant for internal fixation remains controversial. The objective of this study is to establish the relative strength of fixation of a distal femoral locking plate (DFLP) compared with the dynamic condylar screw (DCS) in the distal femur fractures.

MATERIALS AND METHODS

Study was conducted on 16 freshly harvested cadaveric distal femoral specimens, eight implanted with DCS and other eight with DFLP. The construct was made unstable by removing a standard sized medial wedge of 1 cm base (gap-osteotomy) beginning 6 cm proximal to the lateral joint line in distal metaphyseal region with the loss of medial buttress. Fatigue test was conducted under load control mode at the frequency of I Hz. Specimens were subjected to cyclic loading of 2 kN, under observation for 50,000 cycles or until failure/cutout, which ever occurred earlier.

RESULTS

In DFLP group, there was no implant failure and the average number of cycles sustained was 50,000. Six out of eight specimens completed 50,000 cycles and two failed in DCS group. The average number of cycles sustained by DCS was 46150. Though the bone quality as assessed by dual energy X-ray absorptiometry DEXA was comparable in both DFLP and DCS group (P = 0.06), none failed in DFLP group and subsidence was 1.02 ± 0.34 mm (range: 0.60-1.32 mm), which was significantly 43% lower (P = 0.006) than subsidence in DCS group (1.82 ± 0.58; range: 1.20-3.08 mm). The average stiffness of DCS group was 52.8 ± 4.2 N/mm, which was significantly lower than average stiffness of locked condylar plate group (71.2 ± 5.1 N/mm) (P = 0.02).

CONCLUSIONS

DFLP fixation of the distal femur fractures resulted in stronger construct than the DCS fixation in both cyclic loading and ultimate strength in biomechanical testing of a simulated A3 distal femur fracture.

Comparison of Fatigue Properties and Fatigue Crack Growth Rates of Various Implantable Metals

The fatigue strength, effects of a notch on the fatigue strength, and fatigue crack growth rate of Ti-15Zr-4Nb-4Ta alloy were compared with those of other implantable metals. Zr, Nb, and Ta are important alloying elements for Ti alloys for attaining superior long-term corrosion resistance and biocompatibility. The highly biocompatible Ti-15Zr-4Nb-4Ta alloy exhibited an excellent balance between strength and ductility. Its notched tensile strength was much higher than that of a smooth specimen. The strength of 20% cold-worked commercially pure (C.P.) grade 4 Ti was close to that of Ti alloy. The tension-to-tension fatigue strength of an annealed Ti-15Zr-4Nb-4Ta rod at 10⁷ cycles was approximately 740 MPa. The fatigue strength of this alloy was much improved by aging treatment after solution treatment. The fatigue strengths of C.P. grade 4 Ti and stainless steel were markedly improved by 20% cold working. The fatigue strength of Co-Cr-Mo alloy was markedly increased by hot forging. The notch fatigue strengths of 20% cold-worked C.P. grade 4 Ti, and annealed and aged Ti-15Zr-4Nb-4Ta, and annealed Ti-6Al-4V alloys were less than those of the smooth specimens. The fatigue crack growth rate of Ti-15Zr-4Nb-4Ta was the same as that of Ti-6Al-4V. The fatigue crack growth rate in 0.9% NaCl was the same as that in air. Stainless steel and Co-Cr-Mo-Ni-Fe alloy had a larger stress-intensity factor range (ΔK) than Ti alloy.

Retrograde intramedullary nailing for distal femur fracture with osteoporosis

BACKGROUND

The incidence of distal femur fracture in the elderly has been increasing recently, and commonly occurs with osteoporosis. Retrograde intramedullary nailing has been considered a good surgical option for distal femur fracture. The purpose of the present study was to present our surgical results with retrograde intramedullary nailing for distal femur fractures with osteoporosis.

METHODS

Thirteen patients diagnosed with extra-articular distal femur fracture and osteoporosis and managed with retrograde intramedullary nailing were retrospectively reviewed. Cement augmentation was used in four patients, shape memory alloy was used in eight patients and both were used in one patient. All patients were followed up for more than 2 years. Radiologic alignments were scored and Tegner and the Lysholm activity score was used for a functional assessment.

RESULTS

The average time to clinical union was 13 weeks (range, 10 to 15 weeks). In 12 of our cases, the total alignment scores were excellent. At the last follow-up, the mean range of motion was 116° (range, 110° to 125°). The average functional score at postoperative 1 year was 2.6 (range, 1 to 5).

CONCLUSIONS

Retrograde intramedullary nailing is a good surgical option for distal femur fracture with osteoporosis. Cement augmentation and shape memory alloy can also be used for added mechanical stability. This surgical technique is very useful for distal femur fracture with osteoporosis as it promotes fracture healing and early rehabilitation.

Evaluation of methods and timing in nail dynamisation for treating delayed healing femoral shaft fractures

INTRODUCTION

Dynamisation is a simple method for treating femoral shaft fractures (FSFs) in patients with delayed healing after intramedullary nailing. However, only around half of patients with a slow-healing FSF have been successfully treated with this strategy. Although it is thought that dynamisation with a screw preserved in the dynamic locking hole improves treatment outcome in these patients, to date, no studies have demonstrated empirical evidence supporting this technique. In this study, we investigated the effects of dynamisation with and without rotation and length control as well as timing of dynamisation on treatment outcomes in FSF patients with delayed healing.

PATIENTS AND METHODS

Thirty-nine consecutive acute FSF patients with static locking intramedullary nails who subsequently underwent dynamisation were recruited between January 2000 and June 2011. The indication for dynamisation was the presence of gap caused by bone absorption or over-traction at the fracture site when the locking screws were placed. Age, gender, dynamisation method, fracture classification, duration from nail insertion to dynamisation (i.e., timing of dynamisation) and dynamisation outcome were included in the statistical analysis.

RESULTS

Patients whose nail was dynamised with a screw preserved in the dynamic locking hole had a significantly higher successful bone union rate (14/15 vs. 14/24, p=0.028) compared with those with all screws removed from one end of the nail. The patients treated in 10-24 weeks had a significantly increased chance of bone union than those treated after 24 weeks (p=0.027). A significantly higher bone union rate (p=0.036) was observed in 10-24 weeks (83.3%) than after 24 weeks (33.3%) in the group of dynamisation with all screws removed from one end of the nail. No statistical difference in bone union success rate was found between patients at 10-24 weeks and after 24 weeks in the group of dynamisation with a screw preserved in the dynamic locking hole. There were no significant differences in outcome based on other variables.

CONCLUSION

(1) Dynamisation with a screw preserved in the dynamic locking hole was associated with a higher success rate in bone union than all screws removed from one end of the nail for patients with delayed healing FSFs. (2) Early dynamisation (10-24 weeks) had a better outcome than late dynamisation (>24 weeks). Late dynamisation with all screws removed from one end of the nails resulted in a poor success rate. Alternative treatment should be considered if the latter approach is to be adopted.

A biomechanical comparison of multidirectional nail and locking plate fixation in unstable olecranon fractures

BACKGROUND

The main theoretic advantage of proximal olecranon fracture intramedullary fixation is decreased soft-tissue irritation and, potentially, less subsequent hardware removal. Despite this possible benefit, questions remain as to whether intramedullary devices are capable of controlling olecranon fractures to the same extent as locking plates. This study evaluates the ability of a novel multidirectional locking nail to stabilize comminuted fractures and directly compares its biomechanical performance with that of locking olecranon plates.

MATERIALS AND METHODS

We implanted 8 stainless steel locking plates and stainless steel intramedullary nails to stabilize a simulated comminuted fracture in 16 fresh-frozen cadaveric elbows. Flexion-extension, varus-valgus, gap distance, and rotational 3-dimensional angular displacement analysis was conducted over a 60° motion arc (30° to 90°) to assess fragment motion through physiologic cyclic arcs of motion and failure loading. Displacements in all planes were compared.

RESULTS

Both implants showed less than 1° of motion in all measured planes and allowed less than 1 mm of gapping through all loads tested until ultimate failure. All failures occurred by sudden, catastrophic means. The mean failure weight for the nail was 14.4 kg compared with 8.7 kg for the plate (P = .02). The nail survived 1102 cycles, whereas the plate survived 831 cycles (P = .06).

CONCLUSION

In simulated comminuted olecranon fractures, the multidirectional locking intramedullary nails sustained significantly higher maximum loads than the locking plates. The two implants showed no significant differences in fragment control or number of cycles survived. Surgeons can expect the multidirectional locking nails to stabilize comminuted fractures at least as well as locking plates.

In-vitro comparison of LC-DCP- and LCP-constructs in the femur of newborn calves - a pilot study

Background

To compare the biomechanical in-vitro characteristics of limited-contact dynamic compression plate (LC-DCP) and locking compression plate (LCP) constructs in an osteotomy gap model of femoral fracture in neonatal calves. Pairs of intact femurs from 10 calves that had died for reasons unrelated to the study were tested. A 7-hole LC-DCP with six 4.5 mm cortical screws was used in one femur and a 7-hole LCP with four 5.0 mm locking and two 4.5 mm cortical screws was used in the corresponding femur. The constructs were tested to failure by cyclic compression at a speed of 2 mm/s within six increasing force levels.

Results

The bone-thread interface was stripped in 21 of 80 cortical screws (26.3%) before a pre-set insertion torque of 3 Nm was achieved. Only 3 corresponding intact pairs of constructs could be statistically compared for relative structural stiffness, actuator excursion and width of the osteotomy gap. Relative structural stiffness was significantly greater, actuator excursion and width of the osteotomy gap were significantly smaller in the LCP constructs. While failure occurred by loosening of the screws in the LC-DCP constructs, locking constructs failed by cutting large holes in the soft distal metaphyseal bone.

Conclusions

An insertion torque sufficient to provide adequate stability in femurs of newborn calves could not be achieved reliably with 4.5 mm cortical screws. Another limiting factor for both constructs was the weak cancellous bone of the distal fracture fragment. LCP constructs were significantly more resistant to compression than LC-DCP constructs.

Distal femoral fixation: a biomechanical comparison of retrograde nail, retrograde intramedullary nail, and prototype locking retrograde nail

BACKGROUND

Distal femur fractures continue to be a complex surgical problem for which the incidence is increasing. Presently, there is a need for different constructs to address these complex fractures. This study attempts to define the biomechanical properties of several implants.

METHODS

A novel, prototype locking retrograde intramedullary nail and the Russell-Taylor femoral retrograde nail were tested at non-destructive, physiological, axial mode load strength using a young, synthetic bone model for a medial segmental shaft defect in the supracondylar region of the distal femur (medial gap of 10mm, 65mm proximal to the distal joint and parallel to the knee axis). Each specimen was compressively loaded and unloaded to the peak load for 80,000cycles at a 0.5Hz frequency. These were compared to the results from the same lab of the retrograde Trigen intramedullary nail. Motion and peak displacement were measured across the fracture site as a reflection of construct stability.

FINDINGS

Previous testing demonstrated that Trigen intramedullary nail had significantly less motion across the gap and increased overall stiffness of the construct (P<0.05) compared to both Russell-Taylor and prototype nails.

INTERPRETATION

Locking technology used in a nail biomechanically appears to lead to more micro-motion across the fracture gap and to less stiffness in this construct. Further research needs to be invested into intramedullary, locking technology before introducing it into clinical practice.

A modified intramedullary nail interlocking design yields improved stability for fatigue cycling in a canine femur fracture model

Intramedullary nailing has evolved to become the standard of care for most diaphyseal femoral and tibial fractures, as well as an expanding number of metaphyseal fractures. Owing to the unstable nature of some fractures, the intramedullary device may be subjected to significant stresses owing to a lack of solid cortical contact after nailing. In such cases, excessive interfragmentary motion (due to construct toggle) has been shown to occur. Such motion increases the likelihood of a non- or delayed-union. In the current study, two versions of a modified, angle stable interlocking design were subjected to fatigue testing in a segmental defect fracture model representing a canine femur. As a control, a third group of constructs were stabilized with a traditional nail that allowed a small amount of toggle. All constructs were subjected to 50,000 fatigue cycles representing 12 weeks of cage activity at physiologic levels of combined axial-torsional loading. Torsional testing pre- and post-fatigue revealed 4.6 +/- 1.3 degrees of toggle in the traditional nail and no toggle with the angle stable nail designs. The stable nails were also significantly stiffer in axial compression and torsion before and after cycling. These data indicate that the enhanced stability of the modified interlocking designs can be maintained throughout fatigue cycling in a challenging fracture model.

Choosing a proper working length can improve the lifespan of locked plates. A biomechanical study

BACKGROUND

It is hypothesized that the working length influences the implants fatigue behavior. However, few studies addressing this issue came to contrary results. Therefore, we tested systematically the influence of working length and implant material on the plate's endurance.

METHODS

We used an artificial model providing the substantial angle and length conditions of a human femur. A fracture gap of 10mm was bridged with identical shaped plate implants made of stainless steel and grade-2 titanium. The fatigue strength was tested for a short, medium and long working length. Aiming at an implant failure within 80,000 loading cycles the upper load threshold was set to 265N for the titanium plates and to 420N for the steel plates. The lower load threshold was -20N for both plates.

FINDINGS

For the steel plates there was no correlation between fatigue strength and working length. The construct stiffness did not differ at short and medium working length and was reduced by 10% (P=0.047) at long working length. For the titanium plates the fatigue strength tends to increase with the working length but this correlation was not significant (τ=0.417, P=0.051). Further there was a negative correlation between working length and construct stiffness (τ=0.552; P=0.01).

INTERPRETATION

The working length has no appreciable effect on the endurance of the steel plates. Compared to the grade 2-titanium plates the stainless steel plates sustain a larger amount of cyclic load. However, for the titanium plates a larger working length tends to improve the endurance.

Distal femoral fractures: current concepts

The diversity of surgical options for the management of distal femoral fractures reflects the challenges inherent in these injuries. These fractures are frequently comminuted and intra-articular, and they often involve osteoporotic bone, which makes it difficult to reduce and hold them while maintaining joint function and overall limb alignment. Surgery has become the standard of care for displaced fractures and for patients who must obtain rapid return of knee function. The goal of surgical management is to promote early knee motion while restoring the articular surface, maintaining limb length and alignment, and preserving the soft-tissue envelope with a durable fixation that allows functional recovery during bone healing. A variety of surgical exposures, techniques, and implants has been developed to meet these objectives, including intramedullary nailing, screw fixation, and periarticular locked plating, possibly augmented with bone fillers. Recognition of the indications and applications of the principles of modern implants and techniques is fundamental in achieving optimal outcomes.

[The use of blade plate and dynamic screw plate osteosynthesis]

Osteosynthesis in fracture treatment and in some reconstructive procedures with blade plates or dynamic screw systems was the standard procedure for several decades. In this review, the current options and concepts using blade plate osteosynthesis, stabilization of proximal and distal femur fractures and reconstructive procedures with the dynamic hip screw or the dynamic condylar blade are discussed. On the basis of a literature review, the present indications, results and region-specific complications are reported and discussed.Blade plates are used mainly in the context of reconstructive procedures, as well as in the treatment of pseudoarthroses. The Pauwel procedure in femoral neck non-unions is one of the best known indications. In contrast, the dynamic hip screw is the gold standard for stabilization of femoral neck and most pertrochanteric fractures, whereas the dynamic condylar screw is still an alternative to internal fixators for proximal and distal femoral fracture fixations.