Evidence of early stage precursors of polymer crystals by dielectric spectroscopy

Preparation and Structural-Thermodynamical Investigation of Renewable Copolyesters Based on Poly (Ethylene Succinate) and Polyisosorbide

A series of novel renewable copolymers based on poly(ethylene succinate) (PESu) and poly(isosorbide succinate) (PISSu), with the Isosorbide (Is)/PESu molar ratio varying from 5/95 to 75/25, were synthesized in-situ and studied in this work. A sum of characterization techniques was employed here for the structural and thermo-dynamical characterization. The sophisticated technique of dielectric spectroscopy, along with proper analysis, enabled the molecular dynamics mapping of both the local and segmental types, which is presented for such materials for the first time. With increasing the Is fraction, shorter copolymeric entities were gradually formed. Based on the overall findings, the systems were found to be homogeneous, e.g., exhibiting single glass transitions, with the two polymer segments being found to be excellently distributed. The latter is indirect, although strong, evidence for the successful copolymerization. The thermal degradation mechanism for the copolymers was exhaustingly explored employing analytical pyrolysis. The systems exhibited, in general, good thermal stability, according to the thermogravimetric analysis. Confirming one of the initial scopes for the present systems, isosorbide plays here the role of hardener (PISSu) over the soft polymer (PESu), and this is reflected in the monotonic increase of the glass transition temperature, Tg, from -16 to ~56 °C. The introduction of Is results in an increase in constraints (hardening of the matrix), while there seems to be an overall densification of the polymer (decrease of the free volume).

Crystallization with Nodular Aggregation near the Glass Transition Temperature for Syndiotactic Polypropylene

The isothermal crystallization from the melt state of syndiotactic polypropylene (sPP) has been studied by wide-angle X-ray diffraction (WAXD), small-angle X-ray scattering (SAXS), and optical microscopy. The WAXD and SAXS results show the crystallization mechanism near the glass transition temperature in which the crystalline and mesomorphic nodules cover the entire sample with the formation of aggregation regions. For the SAXS analysis, the scattering function for the three-component system has been suggested. Furthermore, to analyze the growth kinetics of the aggregation region for sPP, the time-dependent structure factor combined with the homogeneous and inhomogeneous nucleation-and-growth kinetics has been suggested. The analysis shows that the growth kinetics of the aggregation region for sPP is the homogeneous nucleation-and-growth. The growth velocity of the aggregation region is a natural extrapolation of that of spherulite to the high supercooling region. These results might indicate that the crystallization with the nodular aggregation is a fundamental crystallization process near the glass transition temperature for polymers.

Dielectric Characterization of Core-Shell Structured Poly(vinylidene fluoride)-grafted-BaTiO3 Nanocomposites

Dielectric properties of poly(vinylidene fluoride)-grafted-BaTiO₃ (PVDF-g-BT) core-shell structured nanocomposites obtained from Reversible Addition Fragmentation chain Transfer (RAFT) polymerization of VDF were investigated by Broadband Dielectric Spectroscopy (BDS). The dielectric constant increased along with the BT content, about +50% by addition of 15 vol% of BT, which was around 40% more than expected from predictions using the usual dielectric modeling methods for composite materials, to be ascribed to the effect of the interfacial core-shell structure. The known dielectric relaxations for PVDF were observed for the neat polymer as well as for its nanocomposites, not affected by the presence of nanoparticles. A relaxation process at higher temperatures was found, due to interfacial polarization at the amorphous-crystalline interface, due to the high crystallinity of materials produced by RAFT. Isochronal BDS spectra were exploited to detect the primary relaxation of the amorphous fraction. Thermal analysis demonstrated a very broad endotherm at temperatures much lower than the usual melting peaks, possibly due to the ungrafted fraction of the polymer that is more easily removable by repeated washing of the pristine material with acetone.

Kinetics of Polymer Crystallization with Aggregating Small Crystallites

The isothermal crystallization near the glass transition temperature from the melt state of poly(trimethylene terephthalate) has been studied by wide-angle x-ray diffraction (WAXD), small-angle x-ray scattering (SAXS), and optical microscopy. The SAXS and WAXD results show the crystallization mechanism in which the crystalline nodules cover the entire sample with the formation of aggregation regions. The analysis of the SAXS results using Kolmogorov-Johnson-Mehl-Avrami theory indicates that the formation kinetics of the aggregation regions is of three-dimensional homogeneous nucleation type. The analysis of the SAXS profiles using Sekimoto's theory provides the growth velocity and the nucleation rate of the aggregation region. The temperature dependence of the growth velocity of the aggregation region is a natural extrapolation of that of spherulite to the high supercooling region. The temperature dependence of the nucleation rate of the aggregation region is also represented by the parameters of the spherulitic growth rate. The result of the growth velocities of the aggregation region and the spherulite suggests the existence of precursors at the front of the crystal growth.

Synthesis, crystallization, and molecular mobility in poly(ε-caprolactone) copolyesters of different architectures for biomedical applications studied by calorimetry and dielectric spectroscopy

In this work, we synthesized poly(ε-caprolactone) (PCL) and three copolyesters of different architectures based on three different alcohols, namely a three arm-copolymer based on 1% glycerol (PCL_Gly), a four arm-copolymer based on 1% pentaerythrytol (PCL_PE), and a linear block copolymer based on ∼50% methoxy-poly(ethylene glycol) (PCL_mPEG), all simultaneously with the ring opening polymerization (ROP) of PCL. Due to their biocompatibility and low toxicity, these systems are envisaged for use in drug delivery and tissue engineering applications. Due to the in situ ROP during the copolyesters synthesis, the molecular weight of PCL, Wm initially ∼62 kg mol-1, drops in the copolymers from ∼60k down to ∼5k. For the structure-properties investigation we employed differential scanning calorimetry (DSC and TMDSC), X-ray diffraction (XRD), nuclear magnetic resonance (NMR), Fourier transform infra red (FTIR) spectroscopy, polarized optical microscopy (POM), broadband dielectric spectroscopy (BDS) and isothermal water sorption. DSC revealed that the crystalline fraction of PCL increases whereas the crystallization rate drops in the copolymers in the order PCL ∼ PCL_Gly > PCL_PE ≫ PCL_mPEG, which coincides with that of decreasing Wm. In PCL_mPEG the major amount of PCL (87%) was found to crystallize while the majority of mPEG (92%) was found amorphous exhibiting constrained amorphous mobility and severely slower/weaker crystallization as compared to neat mPEG. Segmental dynamics in BDS, in agreement with DSC, is similar and in general slow for the samples of star-like structure for Wm ≥ 30k arising from PCL, whereas it is severely faster and enhanced in strength for the linear PCL_mPEG (lower Wm) copolymer arising from mPEG. For the latter system, the data provide indications for the formation of complex structures consisting of many small PCL crystallites surrounded by amorphous mPEG segments with constrained dynamics and severely suppressed hydrophilicity. These effects cannot be easily assessed by conventional XRD and POM, confirming the power of the dielectric technique. The overall recordings indicated that the different polymer architecture results in severe changes in the semicrystalline morphology, which demonstrates the potential for tuning the final product performance (permeability, mechanical).

A new Fourier transformation method for SAXS of polymer lamellar crystals

The interface distribution function is composed mainly of the self-interference item of the first interface F₁₁, the interference term of the first and the second interfaces F₁₂, and the interference term of the first and the third interfaces F₁₃.

Effect of chemical structure on the subglass relaxation dynamics of biobased polyesters as revealed by dielectric spectroscopy: 2,5-furandicarboxylic acid vs. trans-1,4-cyclohexanedicarboxylic acid

The chemical structure-dynamics relationship for poly(trimethylene 2,5-furanoate) and poly(trimethylene 1,4-cyclohexanedicarboxylate) was investigated via dielectric spectroscopy and compared with that of poly(trimethylene terephthalate) in order to evaluate the impact on the subglass dynamics of the chemical nature of the ring. Further comparison was accomplished with the neopentyl glycol containing counterparts: poly(neopentyl 2,5-furanoate) and poly(neopentyl 1,4-cyclohexanedicarboxylate). Our study reveals a multimodal nature of the subglass β process. For the more flexible polymers (containing cyclohexane rings) three modes for the β process were detected. The faster mode was assigned to the relaxation of the oxygen linked to the aliphatic carbon, the slower one to the link between the aliphatic ring and the ester group, and the third mode to the aliphatic ring. For stiffer polymers (containing aromatic rings), the local modes appear more coupled. This effect is more evident in the polymers with the furan ring where essentially a single β mode can be resolved.

Dielectric relaxation of polymers: segmental dynamics under structural constraints

In this article we review the recent polymer literature where dielectric spectroscopy has been used to investigate the segmental dynamics of polymers under the constraints produced by self-structuring. Specifically, we consider three cases: (i) semicrystalline polymers, (ii) segregated block-copolymers, and (iii) asymmetric miscible polymer blends. In these three situations the characteristics of the dielectric relaxation associated with the polymer segmental dynamics are markedly affected by the constraints imposed by the corresponding structural features. After reviewing in detail each of the polymer systems, the most common aspects are discussed in the context of the use of dielectric relaxation as a sensitive tool for analyzing structural features in nanostructured polymer systems.

Role of Thermal History and Entanglement Related Thickness Selection in Polymer Crystallization

Using molecular dynamics simulations and primitive path analysis, we show that hot entangled polymer melts can crystallize faster with higher crystallinities and larger crystalline stem lengths, as compared to cold melts under rapid quenching conditions or during cold-crystallization. This counterintuitive phenomenon similar to the so-called Mpemba effect observed for water can be explained by the temperature dependence of entanglements. Our results demonstrate the key role of the entanglement state for crystallization properties and provide a new approach to understand the role of thermal history and to the open question of thickness selection in polymer crystallization.

A high-molecular-weight and high-Tg poly(ester carbonate) partially based on isosorbide: synthesis and structure–property relationships

A new family of high-molecular-weight and high T_g poly(ester carbonate)s partially based on renewable isosorbide were prepared by incorporating 1,4-butanediol and dimethyl terephthalate into poly(isosorbide carbonate).

New understanding in the influence of melt structure and β-nucleating agents on the polymorphic behavior of isotactic polypropylene

Schematic illustration of the two-stage β-nucleation mechanism of β-iPP nucleated with dual-selective β-nucleating agents and the role of ordered structures.

Localized translational motions in semicrystalline poly(ethylene terephthalate) studied by incoherent quasielastic neutron scattering

One of the simplest ways to confine polymeric materials is by self-assembling during the crystallization process. The remaining amorphous phase is then constrained by the lamellar crystals. In this manuscript, we aim to shed additional light in the understanding of the amorphous chains dynamics of semicrystalline polymers above the Tg by using incoherent quasielastic neutron scattering QENS in a nanoscopic time scale (10(-9)-10(-10)s) on poly(ethylene terephthalate). The observed dynamics is satisfactorily described by a theoretical model that considers that the proton mobility follows a random jump-diffusion in a restricted environment. We demonstrate that the combination of macroscopic with nanoscopic dynamic tools allows a complete description of the confined dynamics on a paradigmatic semicrystalline polymer like poly(ethylene terephthalate).

Structure and morphology of thin films of linear aliphatic polyesters prepared by spin-coating

Thin films, with thicknesses from 10 to 400 nm of linear aliphatic polyesters (X, Y), based on propylenediol (X = 3) and on dicarboxylic acid of different chain length (Y = 2, 3, and 4 CH(2) units) were prepared by spin coating of CHCl(3) polymer solutions with different polymer concentrations. Morphology and structure of the spin coated thin films were investigated by atomic force microscopy (AFM) and by grazing incidence X-ray scattering techniques at small, (GISAXS) and wide angles (GIWAXS). AFM revealed a strong dewetting for all three polymers for coatings thinner than 100 nm. The polymer films are clearly semicrystalline for thicknesses higher than 50 nm. GIWAXS of the thicker films revealed their oriented crystalline nature. An edge-on-lamellae morphology is clearly shown by the AFM-phase images even for relatively thin films. SAXS with the beam parallel to the sample plane also support the presence of lamellae perpendicular to the substrate. The use of a mu-beam helped to interpret the GIWAXS patterns and allowed to obtain oriented WAXS patterns from melt solidified filaments. Thus, a crystal chain packing is proposed for the three polymers and consequently the indexing of the observed reflections. Accordingly, the polymer chains lie parallel to the substrate being the bc plane of the monoclinic crystal unit cell parallel to the substrate.

Early structural development in melt-quenched polymer PTT from atomistic molecular dynamic simulations

Molecular dynamics simulations are performed to study the initial structural development in poly(trimethylene terephthalate) (PTT) when quenched below its melting point. The development of local ordering has been observed in our simulations. The thermal properties, such as the glass transition temperature (T(g)) and the melting temperature (T(m)), determined from our simulations are in reasonable agreement with experimental values. It is found that, between these two temperatures, the number of local structures quickly increases during the thermal relaxation period soon after the system is quenched and starts to fluctuate afterwards. The formation and development of local structures is found to be driven mainly by the torsional and van der Waals forces and follows the classical nucleation-growth mechanism. The variation of local structures' fraction with temperature exhibits a maximum between T(g) and T(m), resembling the temperature dependence of the crystallization rate for most polymers. In addition, the backbone torsion distribution for segments within the local structures preferentially reorganizes to the trans-gauche-gauche-trans (t-g-g-t) conformation, the same as that in the crystalline state. As a consequence, we believe that such local structural ordering could be the baby nuclei that have been suggested to form in the early stage of polymer crystallization.

Nonsynchronous change in the head and tail of dioctadecyldimethylammonium bromide molecules during the liquid crystalline to coagel phase transformation process

Dioctadecyldimethylammonium bromide (DODAB) is known to self-assemble into several lamellar structures in water, existing as either liquid crystalline, gel, or coagel phases. In this work, by using differential scanning calorimetry, Fourier transform infrared spectroscopy, and X-ray diffraction techniques, we have characterized the details of the phase transition mechanisms of the DODAB aqueous dispersions. It was found that the liquid crystalline converts to the coagel phase via a two-step mechanism: first to the gel phase upon cooling and then to the stable coagel phase. Although significant conformational changes in the hydrocarbon tails were observed in both steps, changes in the headgroups of DODAB were only detected in the second step. More interestingly, we found that the lipid tails change prior to the headgroups during the overall liquid crystalline to coagel phase transformation process. This is regarded as a nonsynchronicity phenomenon, which reflects the regional (head/tail) imbalance in molecular interactions. Such a nonsynchronicity phenomenon in the self-assembled aggregates composed of the medium-sized DODAB molecules will shed light on our understanding of the polymorphism and reversibility of amphiphiles including both surfactants and biomembrane phospholipids.