A silicon micromachined device for use in blood cell deformability studies

Numerical and experimental study on the development of electric sensor as for measurement of red blood cell deformability in microchannels

A microsensor that can continuously measure the deformability of a single red blood cell (RBC) in its microchannels using microelectrodes is described in this paper. The time series of the electric resistance is measured using an AC current vs. voltage method as the RBC passes between counter-electrode-type micro-membrane sensors attached to the bottom wall of the microchannel. The RBC is deformed by the shear flow created in the microchannel; the degree of deformation depends on the elastic modulus of the RBC. The resistance distribution, which is unique to the shape of the RBC, is analyzed to obtain the deformability of each cell. First, a numerical simulation of the electric field around the electrodes and RBC is carried out to evaluate the influences of the RBC height position, channel height, distance between the electrodes, electrode width, and RBC shape on the sensor sensitivity. Then, a microsensor was designed and fabricated on the basis of the numerical results. Resistance measurement was carried out using samples of normal RBCs and rigidified (Ca(2+)-A23186 treated) RBCs. Visualization measurement of the cells' behavior was carried out using a high-speed camera, and the results were compared with those obtained above to evaluate the performance of the sensor.

Microfluidics analysis of red blood cell membrane viscoelasticity

In this work, a microfluidic system to investigate the flow behavior of red blood cells in a microcirculation-mimicking network of PDMS microchannels with thickness comparable to cell size is presented. We provide the first quantitative description of cell velocity and shape as a function of the applied pressure drop in such devices. Based on these results, a novel methodology to measure cell membrane viscoelastic properties in converging/diverging flow is developed, and the results are in good agreement with data from the literature. In particular, in the diverging channel the effect of RBC surface viscosity is dominant with respect to shear elasticity. Possible applications include measurements of cell deformability in pathological samples, where reliable methods are still lacking.

Whole blood pumping with a microthrottle pump

We have previously reported that microthrottle pumps (MTPs) display the capacity to pump solid phase suspensions such as polystyrene beads which prove challenging to most microfluidic pumps. In this paper we report employing a linear microthrottle pump (LMTP) to pump whole, undiluted, anticoagulated, human venous blood at 200 μl min(-1) with minimal erythrocyte lysis and no observed pump blockage. LMTPs are particularly well suited to particle suspension transport by virtue of their relatively unimpeded internal flow-path. Micropumping of whole blood represents a rigorous real-world test of cell suspension transport given blood's high cell content by volume and erythrocytes' relative fragility. A modification of the standard Drabkin method and its validation to spectrophotometrically quantify low levels of erythrocyte lysis by hemoglobin release is also reported. Erythrocyte lysis rates resulting from transport via LMTP are determined to be below one cell in 500 at a pumping rate of 102 μl min(-1).

Biological Soft Materials

With one or two exceptions, biological materials are "soft", meaning that they combine viscous and elastic elements. This mechanical behavior results from self-assembled supramolecular structures that are stabilized by noncovalent interactions. It is an ongoing and profound challenge to understand the self-organization of biological materials. In many cases, concepts can be imported from soft-matter physics and chemistry, which have traditionally focused on materials such as colloids, polymers, surfactants, and liquid crystals. Using these ideas, it is possible to gain a new perspective on phenomena as diverse as DNA condensation, protein and peptide fibrillization, lipid partitioning in rafts, vesicle fusion and budding, and others, as discussed in this selective review of recent highlights from the literature.

Direct measurement of the impact of impaired erythrocyte deformability on microvascular network perfusion in a microfluidic device

The ability of red blood cells (RBCs, erythrocytes) to deform and pass through capillaries is essential for continual flow of blood in the microvasculature, which ensures an adequate supply of oxygen and nutrients, prompt removal of metabolic waste products, transport of drugs and hormones, and traffic of circulating cells to and from all living tissues. This paper presents a novel tool for evaluating the impact of impaired deformability of RBCs on the flow of blood in the microvasculature by directly measuring perfusion of a test microchannel network with dimensions and topology similar to the real microcirculation. The measurement of microchannel network perfusion is compared with RBC filtration -- a conventional assay of RBC deformability. In contrast to RBC filterability, network perfusion depends linearly on RBC deformability modulated by graded exposure to glutaraldehyde, showing a higher sensitivity to small changes of deformability. The direct measurement of microchannel network perfusion represents a new concept for the field of blood rheology and should prove beneficial for basic science and clinical applications.

Measurement of RBC deformation and velocity in capillaries in vivo

Red blood cells (RBC) become deformed while flowing through capillaries. We captured images of blood flow in capillaries and of RBC in the rat mesentery using a high-speed camera at 2000 frames/s and then directly measured and estimated the deformation and velocity of RBC in a non-uniform capillary. The distribution of the capillary diameter was determined by image processing. We applied a deformation index and simple modeling to observe RBC deformation in capillaries. The average capillary diameter was approximately 6.2 microm, and the average velocity of RBC was about 1.85 mm/s. The average deformation index of RBC in the capillary was about 1.55. The present results showed that RBC in capillaries generally assume a specific shape depending on external forces such as the velocity of the blood flow and capillary diameter in vivo.

A microfluidic model for single-cell capillary obstruction by Plasmodium falciparum-infected erythrocytes

Severe malaria by Plasmodium falciparum is a potentially fatal disease, frequently unresponsive to even the most aggressive treatments. Host organ failure is associated with acquired rigidity of infected red blood cells and capillary blockage. In vitro techniques have played an important role in modeling cell deformability. Although, historically they have either been applied to bulk cell populations or to measure single physical parameters of individual cells. In this article, we demonstrate the unique abilities and benefits of elastomeric microchannels to characterize complex behaviors of single cells, under flow, in multicellular capillary blockages. Channels of 8-, 6-, 4-, and 2-microm widths were readily traversed by the 8 microm-wide, highly elastic, uninfected red blood cells, as well as by infected cells in the early ring stages. Trophozoite stages failed to freely traverse 2- to 4-microm channels; some that passed through the 4-microm channels emerged from constricted space with deformations whose shape-recovery could be observed in real time. In 2-microm channels, trophozoites mimicked "pitting," a normal process in the body where spleen beds remove parasites without destroying the red cell. Schizont forms failed to traverse even 6-microm channels and rapidly formed a capillary blockage. Interestingly, individual uninfected red blood cells readily squeezed through the blockages formed by immobile schizonts in a 6-microm capillary. The last observation can explain the high parasitemia in a growing capillary blockage and the well known benefits of early blood transfusion in severe malaria.

Optical Bioimaging: From Living Tissue to a Single Molecule: Imaging and Functional Analysis of Blood Flow in Organic Microcirculation

Activity of blood cells, erythrocytes, leucocytes, and platelets, in microcirculation was observed by using an intravital microscope and confocal laser scanning microscope connected with an image processing system including fluorescence and phosphorescence emission methods. Dynamic functions of the blood flow were mainly observed in mesentery, brain, and liver tissues of rats. The results are summarized as follows: Deformability of diabetic erythrocytes was significantly lower than that of healthy controls, particularly at high shear rate. The spring constant and Young's modulus of diabetic erythrocytes obviously stiffened, making them hard to deform in the capillary. During hemorrhagic shock and thrombosis, flow velocity and oxygen partial pressure of blood decreased in the brain and liver tissues that can be visualized by using FITC stained erythrocytes and Pd-porphyrin derivative as a pO(2) probe. Platelet adhesion and thrombus formation in the micro-vessels accelerated under the photodynamic reaction; diabetic platelets showed augmented adhesion and aggregation on the vessel wall which was followed by acute thromboembolism. Active oxygen radicals take part in thrombus formation, accompanied with adhesion of the activated leucocytes. Fluorescent dye probes, rhodamine G and acridine orange, are quite useful for visualization of the flow behavior of platelets and leucocytes, respectively.

Handling individual mammalian embryos using microfluidics

We have designed, built, and tested microfluidic systems capable of transporting individual, preimplantation mouse embryos (100-microm to 150-microm diameter) through a network of channels. Typical channels are 160 to 200 microm deep, 250 to 400 microm wide at the top, and narrower at the bottom (0 to 250 microm wide) due to the fabrication process. In these channels, a pressure gradient of 1 Pa/mm causes the medium to flow on the order of 10(-10) m3/s (100 nl/s), with an average speed of 1 to 2 mm/s. Under these flow conditions the embryos roll along the bottoms of the channels, traveling at 1/2 the speed of the fluid. By manipulating the pressure at the wells connected to the ends of the channels, the embryos can be transported to (and retained at) specific locations including culture compartments and retrieval wells.

Direct measurement of erythrocyte deformability in diabetes mellitus with a transparent microchannel capillary model and high-speed video camera system

To measure erythrocyte deformability in vitro, we made transparent microchannels on a crystal substrate as a capillary model. We observed axisymmetrically deformed erythrocytes and defined a deformation index directly from individual flowing erythrocytes. By appropriate choice of channel width and erythrocyte velocity, we could observe erythrocytes deforming to a parachute-like shape similar to that occurring in capillaries. The flowing erythrocytes magnified 200-fold through microscopy were recorded with an image-intensified high-speed video camera system. The sensitivity of deformability measurement was confirmed by comparing the deformation index in healthy controls with erythrocytes whose membranes were hardened by glutaraldehyde. We confirmed that the crystal microchannel system is a valuable tool for erythrocyte deformability measurement. Microangiopathy is a characteristic complication of diabetes mellitus. A decrease in erythrocyte deformability may be part of the cause of this complication. In order to identify the difference in erythrocyte deformability between control and diabetic erythrocytes, we measured erythrocyte deformability using transparent crystal microchannels and a high-speed video camera system. The deformability of diabetic erythrocytes was indeed measurably lower than that of erythrocytes in healthy controls. This result suggests that impaired deformability in diabetic erythrocytes can cause altered viscosity and increase the shear stress on the microvessel wall.

Confocal imaging of flows in artificial venular bifurcations

We describe a new experimental methodology for visualizing three-dimensional structures in microscopic tubes under flow conditions. Through the use of microfabrication techniques, artificial venular bifurcations are constructed from glass tubes with semicircular cross sections (radius = 50 mu). Aqueous fluorescent solutions are infused into the tubes at flow rates of about 1 microliter/min, a value comparable to blood flow in the microcirculation. The flow is imaged using a combination of confocal microscopy and three-dimensional image reconstruction software techniques. The quantitative accuracy of the experimental method is evaluated by measuring the "separation surface," a formation resulting from converging flows at a bifurcation. Details of the fabrication process, fluidics, confocal microscopy, image reconstructions, optical effects, and computations are described. We show the first three-dimensional visualization of a microscopic flow structure using confocal microscopy, and within certain limitations, quantitative agreement between the measured and computed positions of the separation surface.

Miniaturization of analytical systems

Miniaturization has been a long-term trend in clinical diagnostics instrumentation. Now a range of new technologies, including micromachining and molecular self-assembly, are providing the means for further size reduction of analyzers to devices with micro- to nanometer dimensions and submicroliter volumes. Many analytical techniques (e.g., mass spectrometry and electrophoresis) have been successfully implemented on microchips made from silicon, glass, or plastic. The new impetus for miniaturization stems from the perceived benefits of faster, easier, less costly, and more convenient analyses and by the needs of the pharmaceutical industry for microscale, massively parallel drug discovery assays. Perfecting a user-friendly interface between a human and a microchip and determining the realistic lower limit for sample volume are key issues in the future implementation of these devices. Resolution of these issues will be important for the long-term success of microminiature analyzers; in the meantime, the scope, diversity, and rate of progress in the development of these devices promises products in the near future.

Integrated cell isolation and polymerase chain reaction analysis using silicon microfilter chambers

White blood cells are isolated from whole blood in silicon-glass 4.5-microliter microchips containing a series of 3.5-micron feature-sized 'weir-type' filters, formed by an etched silicon dam spanning the flow chamber. Genomic DNA targets, e.g., dystrophin gene, can be directly amplified using the polymerase chain reaction (PCR) from the white cells isolated on the filters. This dual function microchip provides a means to simplify nucleic acid analyses by integrating in a single device two key steps in the analytical procedure, namely, cell isolation and PCR.

A novel instrument for studying the flow behaviour of erythrocytes through microchannels simulating human blood capillaries

A novel instrument has been developed to study the microrheology of erythrocytes as they flow through channels of dimensions similar to human blood capillaries. The channels are produced in silicon substrates using microengineering technology. Accurately defined, physiological driving pressures and temperatures are employed whilst precise, real-time image processing allows individual cells to be monitored continuously during their transit. The instrument characterises each cell in a sample of ca. 1000 in terms of its volume and flow velocity profile during its transit through a channel. The unique representation of the data in volume/velocity space provides new insight into the microrheological behaviour of blood. The image processing and subsequent data analysis enable the system to reject anomalous events such as multiple cell transits, thereby ensuring integrity of the resulting data. By employing an array of microfluidic flow channels we can integrate a number of different but precise and highly reproducible channel sizes and geometries within one array, thereby allowing multiple, concurrent isobaric measurements on one sample. As an illustration of the performance of the system, volume/velocity data sets recorded in a microfluidic device incorporating multiple channels of 100 microns length and individual widths ranging between 3.0 and 4.0 microns are presented.