A nanodiamond-tapered fiber system with high single-mode coupling efficiency

Heterogeneous Integration of Solid-State Quantum Systems with a Foundry Photonics Platform

Diamond color centers are promising optically addressable solid-state spins that can be matter-qubits, mediate deterministic interaction between photons, and act as single photon emitters. Useful quantum computers will comprise millions of logical qubits. To become useful in constructing quantum computers, spin-photon interfaces must, therefore, become scalable and be compatible with mass-manufacturable photonics and electronics. Here, we demonstrate the heterogeneous integration of NV centers in nanodiamond with low-fluorescence silicon nitride photonics from a standard 180 nm CMOS foundry process. Nanodiamonds are positioned over predefined sites in a regular array on a waveguide in a single postprocessing step. Using an array of optical fibers, we excite NV centers selectively from an array of six integrated nanodiamond sites and collect the photoluminescence (PL) in each case into waveguide circuitry on-chip. We verify single photon emission by an on-chip Hanbury Brown and Twiss cross-correlation measurement, which is a key characterization experiment otherwise typically performed routinely with discrete optics. Our work opens up a simple and effective route to simultaneously address large arrays of individual optically active spins at scale, without requiring discrete bulk optical setups. This is enabled by the heterogeneous integration of NV center nanodiamonds with CMOS photonics.

Sensing of Magnetic-Field Gradients with Nanodiamonds on Optical Glass-Fiber Facets

We demonstrate a photonic sensor of the magnetic field and its gradients with remote readout. The sensor is based on optically detected magnetic resonance (ODMR) in nanodiamonds with nitrogen-vacancy color centers that are covalently attached as a thin film on one facet of an optical fiber bundle. By measuring ODMR signals from a group of individual fibers in an ∼0.5-mm-wide imaging bundle, differences of local magnetic field strengths and magnetic field gradients are determined across the plane of the bundle facet. The measured gradients are created by direct electric currents flowing in a wire placed near the nanodiamond film. The measurement enabled the determination of the net magnetic field corresponding to various current directions and their corresponding magnetic field gradients. This demonstration opens up a perspective for compact fiber-based endoscopy, with additional avenues for remote and sensitive magnetic field detection with submicrometer spatial resolution under ambient conditions.

Numerical analysis of the ultra-wide tunability of nanofiber Bragg cavities

Nanofiber Bragg cavities (NFBCs) are solid-state microcavities fabricated in optical tapered fiber. They can be tuned to a resonance wavelength of more than 20 nm by applying mechanical tension. This property is important for matching the resonance wavelength of an NFBC with the emission wavelength of single-photon emitters. However, the mechanism of the ultra-wide tunability and the limitation of the tuning range have not yet been clarified. It is important to comprehensively analyze both the deformation of the cavity structure in an NFBC and the change in the optical properties due to the deformation. Here, we present an analysis of the ultra-wide tunability of an NFBC and the limitation of the tuning range using three dimensional (3D) finite element method (FEM) and 3D finite-difference time-domain (FDTD) optical simulations. When we applied a tensile force of 200 μN to the NFBC, a stress of 5.18 GPa was concentrated at the groove in the grating. The grating period was extended from 300 to 313.2 nm, while the diameter slightly shrank from 300 to 297.1 nm in the direction of the grooves and from 300 to 298 nm in the direction orthogonal to the grooves. This deformation shifted the resonance peak by 21.5 nm. These simulations indicated that both the elongation of the grating period and the small shrinkage of the diameter contributed to the ultra-wide tunability of the NFBC. We also calculated the dependence of the stress at the groove, the resonance wavelength, and the quality Q factor while changing the total elongation of the NFBC. The dependence of the stress on the elongation was 1.68 × 10^-2 GPa/μm. The dependence of the resonance wavelength was 0.07 nm/μm, which almost agrees with the experimental result. When the NFBC, assumed to have the total length of 32 mm, was stretched by 380 μm with the tensile force of 250 μN, the Q factor for the polarization mode parallel to the groove changed from 535 to 443, which corresponded to a change in Purcell factor from 5.3 to 4.9. This slight reduction seems acceptable for the application as single photon sources. Furthermore, assuming a rupture strain of the nanofiber of 10 GPa, it was estimated that the resonance peak could be shifted by up to about 42 nm.

Twin-nanofiber structure for a highly efficient single-photon collection

Optical nanofiber-based single-photon source has attracted considerable interest due to its property of seamless integration with a single-mode fiber. With nanostructure engraved in the nanofiber, the single-photon collection efficiency can be greatly boosted with enhanced interaction between the single quantum emitter and the guided light. However, the prerequisite nanofabrication processes introduce complexities and extra loss. Here, we demonstrate that by simply placing a quantum emitter in the gap of two parallel nanofibers, single-photon coupling efficiency may reach 54.2%. Our numerical simulation results indicate that photon coupling efficiency of such simple structure is insensitive to the discrepancy in nanofiber radii, which further reduces the difficulties in device fabrication.

Hybrid device of hexagonal boron nitride nanoflakes with defect centres and a nano-fibre Bragg cavity

Solid-state quantum emitters coupled with a single mode fibre are of interest for photonic and quantum applications. In this context, nanofibre Bragg cavities (NFBCs), which are microcavities fabricated in an optical nanofibre, are promising devices because they can efficiently couple photons emitted from the quantum emitters to the single mode fibre. Recently, we have realized a hybrid device of an NFBC and a single colloidal CdSe/ZnS quantum dot. However, colloidal quantum dots exhibit inherent photo-bleaching. Thus, it is desired to couple an NFBC with hexagonal boron nitride (hBN) as stable quantum emitters. In this work, we realize a hybrid system of an NFBC and ensemble defect centres in hBN nanoflakes. In this experiment, we fabricate NFBCs with a quality factor of 807 and a resonant wavelength at around 573 nm, which matches well with the fluorescent wavelength of the hBN, using helium-focused ion beam (FIB) system. We also develop a manipulation system to place hBN nanoflakes on a cavity region of the NFBCs and realize a hybrid device with an NFBC. By exciting the nanoflakes via an objective lens and collecting the fluorescence through the NFBC, we observe a sharp emission peak at the resonant wavelength of the NFBC.

Diamond quantum thermometry: from foundations to applications

Diamond quantum thermometry exploits the optical and electrical spin properties of colour defect centres in diamonds and, acts as a quantum sensing method exhibiting ultrahigh precision and robustness. Compared to the existing luminescent nanothermometry techniques, a diamond quantum thermometer can be operated over a wide temperature range and a sensor spatial scale ranging from nanometres to micrometres. Further, diamond quantum thermometry is employed in several applications, including electronics and biology, to explore these fields with nanoscale temperature measurements. This review covers the operational principles of diamond quantum thermometry for spin-based and all-optical methods, material development of diamonds with a focus on thermometry, and examples of applications in electrical and biological systems with demand-based technological requirements.

Preferential coupling of diamond NV centres in step-index fibres

Diamonds containing the negatively charged nitrogen-vacancy centre are a promising system for room-temperature magnetometry. The combination of nano- and micro-diamond particles with optical fibres provides an option for deploying nitrogen-vacancy magnetometers in harsh and challenging environments. Here we numerically explore the coupling efficiency from nitrogen-vacancy centres within a diamond doped at the core/clad interface across a range of commercially available fibre types so as to inform the design process for a diamond in fibre magnetometers. We determine coupling efficiencies from nitrogen-vacancy centres to the guided modes of a step-index fibre and predict the optically detected magnetic resonance (ODMR) generated by a ensemble of four nitrogen-vacancy centres in this hybrid fibre system. Our results show that the coupling efficiency is enhanced with a high refractive index difference between the fibre core and cladding and depends on the radial position of the nitrogen-vacancy centres in the fibre core. Our ODMR simulations show that due to the preferential coupling of the nitrogen-vacancy emission to the fibre guided modes, certain magnetometry features such as ODMR contrast can be enhanced and lead to improved sensitivity in such diamond-fibre systems, relative to conventional diamond only ensemble geometries.

Planar antenna designs for efficient coupling between a single emitter and an optical fiber

Fluorescence detection is a well-established readout method for sensing, especially for in-vitro diagnostics (IVD). A practical way to guide the emitted signal to a detector is by means of an optical fiber. However, coupling fluorescence into a fiber is challenging and commonly lacks single-molecule sensitivity. In this work, we investigate specific fiber geometries, materials and coatings that in combination with a planar Yagi-Uda antenna reach efficient excitation and collection. The simulation of a practical setting determines more than 70% coupling efficiency for a horizontally oriented dipole, with respect to the planar antenna, emitting at 700 nm and embedded in polyvinyl alcohol (PVA). Moreover, the coupling efficiency would only scale by a factor of 2/3 for emitters with random orientation, as a result of the antenna geometry. These findings are relevant for single-molecule detection with fiber optics and have implications for other applications involving the coupling of light with nano-scale sources and detectors. Scanning the surface of a sample with such fibers could also be advantageous for imaging techniques to provide a low background noise and a high resolution.

Direct optical excitation of an NV center via a nanofiber Bragg-cavity: a theoretical simulation

Direct optical excitation of a nitrogen-vacancy (NV) center in nanodiamond by light via a nanofiber is of interest for all-fiber-integrated quantum applications. However, the background light induced by the excitation light via the nanofiber is problematic as it has the same optical wavelength as the emission light from the NV center. In this paper, we propose using a nanofiber Bragg cavity to address this problem. We numerically simulate and estimate the electric field of a nanodiamond induced by excitation light applied from an objective lens on a confocal microscope system, a nanofiber, and nanofiber Bragg-cavities (NFBCs). We estimate that by using a nanofiber, the optical excitation intensity can be decreased by roughly a factor of 10 compared to using an objective lens, while for an NFBC with a grating number of 240 (120 for one side) on a nanofiber the optical excitation intensity can be significantly decreased by roughly a factor of 100. This reduction of optical excitation intensity will make it possible to distinguish the fluorescence of the NV center from the background light.

Fabrication of a nanofiber Bragg cavity with high quality factor using a focused helium ion beam

Nanofiber Bragg cavities (NFBCs) are solid-state microcavities fabricated in an optical tapered fiber. NFBCs are promising candidates as a platform for photonic quantum information devices due to their small mode volume, ultra-high coupling efficiencies, and ultra-wide tunability. However, the quality (Q) factor has been limited to be approximately 250, which may be due to limitations in the fabrication process. Here we report high Q NFBCs fabricated using a focused helium ion beam. Whenan NFBC with grooves of 640 periods is fabricated, the Q factor is over 4170, which is more than 16 times larger than that previously fabricated using a focused gallium ion beam.

Efficient nitrogen-vacancy centers' fluorescence excitation and collection from micrometer-sized diamond by a tapered optical fiber in endoscope-type configuration

Using an optical fiber to both excite the nitrogen-vacancy (NV) center in diamond and collect its fluorescence is essential to build NV-based endoscope-type sensor. Such endoscope-type sensor can reach inaccessible fields for traditional NV-based sensors built by bulky optical components and extend the application areas. Since single NV's fluorescence is weak and can easily be buried in fluorescence from optical fiber core's oxide defects excited by the green laser, fixing a micrometer size diamond containing high-density NVs rather than a nanodiamond containing single NV or several NVs on the apex of an optical fiber to build an endoscope-type sensor is more implementable. Unfortunately, due to small numerical aperture (NA), most of the optical fibers have a low fluorescence collection efficiency, which limits the sensitivity and spatial resolution of the NV-based endoscope-type sensor. Here, using a tapered optical fiber (TOF) tip, we significantly improve the efficiency of the laser excitation and fluorescence collection of the NV ensembles in diamond. This could potentially enhance the sensitivity and spatial resolution of the NV-based endoscope-type sensor. Numerical calculations show that the TOF tip delivers a high NA and has a high NV excitation and fluorescence collection efficiency. Experiments demonstrate that such TOF tip can obtain up to over 7-fold excitation efficiency and over 15-fold fluorescence collection efficiency of that from a flat-ended fiber (non-TOF) tip.

Non-contact detection of nanoscale structures using optical nanofiber

The detection of nanoscale structure/material property in a wide observation area is becoming very important in various application fields. However, it is difficult to utilize current optical technologies. Toward the realization of novel alternative, we have investigated a new optical sensing method using an optical nanofiber. When the nanofiber vertically approached a glass prism with a partial gold film, the material differences between the glass and the gold were detected as a transmittance difference of 6% with a vertical resolution of 9.6 nm. The nanofiber was also scanned 100 nm above an artificial small protruding object with a width of 240 nm. The object was detected with a horizontal resolution of 630 nm, which was less than the wavelength of the probe light.

Observation of the linewidth broadening of single spins in diamond nanoparticles in aqueous fluid and its relation to the rotational Brownian motion

Capturing the fast rotational motion of single nanoparticles has been hindered owing to the difficulty of acquiring directional information under the optical diffraction limit. Here, we report the linewidth broadening of the electron spin resonance of single nitrogen vacancy (NV) centers that matches the rotational diffusion constant of the host nanodiamonds. When nanodiamonds are gradually detached from the substrates that they were fixed to, their optically detected spin resonance peaks are broadened by 1.8 MHz, which corresponds to the rotational diffusion constant of nanoparticles with a diameter of 11.4 nm from the Einstein–Smoluchowski relation.

Efficient Extraction of Light from a Nitrogen-Vacancy Center in a Diamond Parabolic Reflector

Quantum emitters in solids are being developed for a range of quantum technologies, including quantum networks, computing, and sensing. However, a remaining challenge is the poor photon collection due to the high refractive index of most host materials. Here we overcome this limitation by introducing monolithic parabolic reflectors as an efficient geometry for broadband photon extraction from quantum emitter and experimentally demonstrate this device for the nitrogen-vacancy (NV) center in diamond. Simulations indicate a photon collection efficiency exceeding 75% across the visible spectrum and experimental devices, fabricated using a high-throughput gray scale lithography process, demonstrating a photon extraction efficiency of (41 ± 5)%. This device enables a raw experimental detection efficiency of (12 ± 1)% with fluorescence detection rates as high as (4.114 ± 0.003) × 10⁶ counts per second (cps) from a single NV center. Enabled by our deterministic emitter localization and fabrication process, we find a high number of exceptional devices with an average count rate of (3.1 ± 0.9) × 10⁶ cps.

Magnetically sensitive nanodiamond-doped tellurite glass fibers

Traditional optical fibers are insensitive to magnetic fields, however many applications would benefit from fiber-based magnetometry devices. In this work, we demonstrate a magnetically sensitive optical fiber by doping nanodiamonds containing nitrogen vacancy centers into tellurite glass fibers. The fabrication process provides a robust and isolated sensing platform as the magnetic sensors are fixed in the tellurite glass matrix. Using optically detected magnetic resonance from the doped nanodiamonds, we demonstrate detection of local magnetic fields via side excitation and longitudinal collection. This is a first step towards intrinsically magneto-sensitive fiber devices with future applications in medical magneto-endoscopy and remote mineral exploration sensing.

Fiber-Coupled Diamond Micro-Waveguides toward an Efficient Quantum Interface for Spin Defect Centers

We report the direct integration and efficient coupling of nitrogen vacancy (NV) color centers in diamond nanophotonic structures into a fiber-based photonic architecture at cryogenic temperatures. NV centers are embedded in diamond micro-waveguides (μWGs), which are coupled to fiber tapers. Fiber tapers have low-loss connection to single-mode optical fibers and hence enable efficient integration of NV centers into optical fiber networks. We numerically optimize the parameters of the μWG-fiber-taper devices designed particularly for use in cryogenic experiments, resulting in 35.6% coupling efficiency, and experimentally demonstrate cooling of these devices to the liquid helium temperature of 4.2 K without loss of the fiber transmission. We observe sharp zero-phonon lines in the fluorescence of NV centers through the pigtailed fibers at 100 K. The optimized devices with high photon coupling efficiency and the demonstration of cooling to cryogenic temperatures are an important step to realize fiber-based quantum nanophotonic interfaces using diamond spin defect centers.

Efficient Single-Photon Coupling from a Nitrogen-Vacancy Center Embedded in a Diamond Nanowire Utilizing an Optical Nanofiber

Nitrogen-Vacancy (NV) centers in diamond are promising solid-state quantum emitters that can be utilized for photonic quantum applications. Various diamond nanophotonic devices have been fabricated for efficient extraction of single photons emitted from NV centers to a single guided mode. However, for constructing scalable quantum networks, further efficient coupling of single photons to a guided mode of a single-mode fiber (SMF) is indispensable and a difficult challenge. Here, we propose a novel efficient hybrid system between an optical nanofiber and a cylindrical-structured diamond nanowire. The maximum coupling efficiency as high as 75% for the sum of both fiber ends is obtained by numerical simulations. The proposed hybrid system will provide a simple and efficient interface between solid-state quantum emitters and a SMF suitable for constructing scalable quantum networks.

Higher-order micro-fiber modes for Escherichia coli manipulation using a tapered seven-core fiber

Optical manipulation using optical micro- and nano-fibers has shown potential for controlling bacterial activities such as E. coli trapping, propelling, and binding. Most of these manipulations have been performed using the propagation of the fundamental mode through the fiber. However, along the maximum mode-intensity axis, the higher-order modes have longer evanescent field extensions and larger field amplitudes at the fiber waist than the fundamental mode, opening up new possibilities for manipulating E. coli bacteria. In this work, a compact seven-core fiber (SCF)-based micro-fiber/optical tweezers was demonstrated for trapping, propelling, and rotating E. coli bacteria using the excitation of higher-order modes. The diameter of the SCF taper was 4 µm at the taper waist, which was much larger than that of previous nano-fiber tweezers. The laser wavelength was tunable from 1500 nm to 1600 nm, simultaneously causing photophoretic force, gradient force, and scattering force. This work provides a new opportunity for better understanding optical manipulation using higher-order modes at the single-cell level.

Manipulation of single nanodiamonds to ultrathin fiber-taper nanofibers and control of NV-spin states toward fiber-integrated λ-systems

We report on the coupling of single nitrogen vacancy (NV) centers to ultrathin fiber-taper nanofibers by the manipulation of single diamond nanocrystals on the nanofibers under real-time observation of nanodiamond fluorescence. Spin-dependent fluorescence of the single NV centers is efficiently detected through the nanofiber. We show control of the spin sub-level structure of the electronic ground state using an external magnetic field and clearly observe a frequency fine tuning of [Formula: see text]. This observation demonstrates a possibility of realizing fiber-integrated quantum λ-systems, which can be used for various quantum information devices including push-pull quantum memory and quantum gates.

Detailed numerical analysis of photon emission from a single light emitter coupled with a nanofiber Bragg cavity

Coupling of a single dipole with a nanofiber Bragg cavity (NFBC) approximating an actually fabricated structure was numerically analyzed using three dimensional finite-difference time-domain simulations for different dipole positions. For the given model structure, the Purcell factor and coupling efficiency reached to 19.1 and 82%, respectively, when the dipole is placed outside the surface of the fiber. Interestingly, these values are very close to the highest values of 20.2 and 84% obtained for the case when the dipole was located inside the fiber at the center. The analysis performed in this study will be useful in improving the performance of single-photon emitter-related quantum devices using NFBCs.

Measuring the charge density of a tapered optical fiber using trapped microparticles

We report the measurements of charge density of tapered optical fibers using charged particles confined in a linear Paul trap at ambient pressure. A tapered optical fiber is placed across the trap axis at a right angle, and polystyrene microparticles are trapped along the trap axis. The distance between the equilibrium position of a positively charged particle and the tapered fiber is used to estimate the amount of charge per unit length of the fiber without knowing the amount of charge of the trapped particle. The charge per unit length of a tapered fiber with a diameter of 1.6 μm was measured to be 2-1+3×10^-11 C/m.

Efficient photon coupling from a diamond nitrogen vacancy center by integration with silica fiber

A central goal in quantum information science is to efficiently interface photons with single optical modes for quantum networking and distributed quantum computing. Here, we introduce and experimentally demonstrate a compact and efficient method for the low-loss coupling of a solid-state qubit, the nitrogen vacancy (NV) center in diamond, with a single-mode optical fiber. In this approach, single-mode tapered diamond waveguides containing exactly one high quality NV memory are selected and integrated on tapered silica fibers. Numerical optimization of an adiabatic coupler indicates that near-unity-efficiency photon transfer is possible between the two modes. Experimentally, we find an overall collection efficiency between 16% and 37% and estimate a single photon count rate at saturation above 700 kHz. This integrated system enables robust, alignment-free, and efficient interfacing of single-mode optical fibers with single photon emitters and quantum memories in solids.

Ultrathin fiber-taper coupling with nitrogen vacancy centers in nanodiamonds at cryogenic temperatures

We demonstrate cooling of ultrathin fiber tapers coupled with nitrogen vacancy (NV) centers in nanodiamonds to cryogenic temperatures. Nanodiamonds containing multiple NV centers are deposited on the subwavelength 480-nm-diameter nanofiber region of fiber tapers. The fiber tapers are successfully cooled to 9 K using our home-built mounting holder and an optimized cooling speed. The fluorescence from the nanodiamond NV centers is efficiently channeled into a single guided mode and shows characteristic sharp zero-phonon lines (ZPLs) of both neutral and negatively charged NV centers. The present nanofiber/nanodiamond hybrid systems at cryogenic temperatures can be used as NV-based quantum information devices and for highly sensitive nanoscale magnetometry in a cryogenic environment.

Diameter measurement of optical nanofibers using a composite photonic crystal cavity

We demonstrate a method for making precise measurements of the diameter of a tapered optical fiber with a sub-wavelength diameter waist (an optical nanofiber). The essence of the method is to create a composite photonic crystal cavity by mounting a defect-mode grating on an optical nanofiber. The resultant cavity has a resonance wavelength that is sensitive to the nanofiber's diameter, allowing the diameter to be inferred from optical measurements. This method offers a precise, nondestructive, and in situ way to characterize the nanofiber diameter.

Highly efficient coupling of nanolight emitters to a ultra-wide tunable nanofibre cavity

Solid-state microcavities combining ultra-small mode volume, wide-range resonance frequency tuning, as well as lossless coupling to a single mode fibre are integral tools for nanophotonics and quantum networks. We developed an integrated system providing all of these three indispensable properties. It consists of a nanofibre Bragg cavity (NFBC) with the mode volume of under 1 μm(3) and repeatable tuning capability over more than 20 nm at visible wavelengths. In order to demonstrate quantum light-matter interaction, we establish coupling of quantum dots to our tunable NFBC and achieve an emission enhancement by a factor of 2.7.

Numerical simulations of nanodiamond nitrogen-vacancy centers coupled with tapered optical fibers as hybrid quantum nanophotonic devices

Tapered optical fibers are promising one-dimensional nanophotonic waveguides that can provide efficient coupling between their fundamental mode and quantum nanoemitters placed inside them. Here, we present numerical studies on the coupling of single nitrogen-vacancy (NV) centers (single point dipoles) in nanodiamonds with tapered fibers. Our results lead to two important conclusions: (1) A maximum coupling efficiency of 53.4% can be realized for the two fiber ends when the NV bare dipole is located at the center of the tapered fiber. (2) NV centers even in 100-nm-sized nanodiamonds where bulk-like optical properties were reported show a coupling efficiency of 22% at the taper surface, with the coupling efficiency monotonically decreasing as the nanodiamond size increases. These results will be helpful in guiding the development of hybrid quantum devices for applications in quantum information science.

Self-formed cavity quantum electrodynamics in coupled dipole cylindrical-waveguide systems

An ideal optical cavity operates by confining light in all three dimensions. We show that a cylindrical waveguide can provide the longitudinal confinement required to form a two dimensional cavity, described here as a self-formed cavity, by locating a dipole, directed along the waveguide, on the interface of the waveguide. The cavity resonance modes lead to peaks in the radiation of the dipole-waveguide system that have no contribution due to the skew rays that exist in longitudinally invariant waveguides and reduce their Q-factor. Using a theoretical model, we evaluate the Q-factor and modal volume of the cavity formed by a dipole-cylindrical-waveguide system and show that such a cavity allows access to both the strong and weak coupling regimes of cavity quantum electrodynamics.

Frequency down-conversion of 637 nm light to the telecommunication band for non-classical light emitted from NV centers in diamond

We demonstrate a low-noise frequency down-conversion of photons at 637 nm to the telecommunication band at 1587 nm by the difference frequency generation in a periodically-poled lithium niobate. An internal conversion efficiency of the converter is estimated to be 0.44 at the maximum which is achieved by a pump power of 0.43 W, whereas a rate of internal background photons caused by the strong cw pump laser is estimated to be 9 kHz/mW within a bandwidth of about 1 nm. By using the experimental values related to the intrinsic property of the converter, and using the intensity correlation and the average photon number of a 637 nm input light pulse, we derive the intensity correlation of a converted telecom light pulse. Then we discuss feasibility of a single-photon frequency conversion to the telecommunication band for a long-distance quantum communication based on NV centers in diamond.

Efficient single-mode photon-coupling device utilizing a nanofiber tip

Single-photon sources are important elements in quantum optics and quantum information science. It is crucial that such sources be able to couple photons emitted from a single quantum emitter to a single propagating mode, preferably to the guided mode of a single-mode optical fiber, with high efficiency. Various photonic devices have been successfully demonstrated to efficiently couple photons from an emitter to a single mode of a cavity or a waveguide. However, efficient coupling of these devices to optical fibers is sometimes challenging. Here we show that up to 38% of photons from an emitter can be directly coupled to a single-mode optical fiber by utilizing the flat tip of a silica nanofiber. With the aid of a metallic mirror, the efficiency can be increased to 76%. The use of a silicon waveguide further increases the efficiency to 87%. This simple device can be applied to various quantum emitters.

Observation of 1.2-GHz linewidth of zero-phonon-line in photoluminescence spectra of nitrogen vacancy centers in nanodiamonds using a Fabry-Perot interferometer

Photoluminescence (PL) spectra of single nitrogen vacancy (NV) centers in 50-nm diamond nanocrystals at the zero-phonon line (ZPL) were directly observed using a Fabry-Perot interferometer at cryogenic temperatures. The narrowest linewidth of ZPL was 1.2 GHz (1.9 ± 0.7 GHz on average), comparable to ZPL linewidths in PL spectra reported for NV centers in pure bulk diamond. This observation is important to the application of NV centers for use in quantum communication and computation devices, and in nano-sensing.

Two-photon excited fluorescence from a pseudoisocyanine-attached gold-coated tip via a thin tapered fiber under a weak continuous wave excitation

A simple tapered fiber based photonic-plasmonic hybrid nanostructure composed of a thin tapered fiber and a pseudoisocyanine (PIC)-attached Au-coated tip was demonstrated. Using this simple hybrid nanostructure, we succeeded in observing two-photon excited fluorescence from the PIC dye molecules under a weak continuous wave excitation condition. From the results of the tip-fiber distance dependence and excitation polarization dependence, we found that using a thin tapered fiber and an Au-coated tip realized efficient coupling of the incident light (~95%) and LSP excitation at the Au-coated tip, suggesting the possibility of efficiently inducing two-photon excited fluorescence from the PIC dye molecules attached on the Au-coated tip. This simple photonic-plasmonic hybrid system is one of the promising tools for single photon sources, highly efficient plasmonic sensors, and integrated nonlinear plasmonic devices.

Three-dimensional quantum photonic elements based on single nitrogen vacancy-centres in laser-written microstructures

To fully integrate quantum optical technology, active quantum systems must be combined with resonant microstructures and optical interconnects harvesting and routing photons in three diemsnsions (3D) on one chip. We fabricate such combined structures for the first time by using two-photon laser lithography and a photoresist containing nanodiamonds including nitrogen vacancy-centers. As an example for possible functionality, single-photon generation, collection, and transport is successfully accomplished. The single photons are efficiently collected via resonators and routed in 3D through waveguides, all on one optical chip. Our one-step fabrication scheme is easy to implement, scalable and flexible. Thus, other complex assemblies of 3D quantum optical structures are feasible as well.

Spectroscopy, manipulation and trapping of neutral atoms, molecules, and other particles using optical nanofibers: a review

The use of tapered optical fibers, i.e., optical nanofibers, for spectroscopy and the detection of small numbers of particles, such as neutral atoms or molecules, has been gaining interest in recent years. In this review, we briefly introduce the optical nanofiber, its fabrication, and optical mode propagation within. We discuss recent progress on the integration of optical nanofibers into laser-cooled atom and vapor systems, paying particular attention to spectroscopy, cold atom cloud characterization, and optical trapping schemes. Next, a natural extension of this work to molecules is introduced. Finally, we consider several alternatives to optical nanofibers that display some advantages for specific applications.

Three-dimensional optical manipulation of a single electron spin

Nitrogen vacancy (NV) centres in diamond are promising elemental blocks for quantum optics, spin-based quantum information processing and high-resolution sensing. However, fully exploiting the capabilities of these NV centres requires suitable strategies to accurately manipulate them. Here, we use optical tweezers as a tool to achieve deterministic trapping and three-dimensional spatial manipulation of individual nanodiamonds hosting a single NV spin. Remarkably, we find that the NV axis is nearly fixed inside the trap and can be controlled in situ by adjusting the polarization of the trapping light. By combining this unique spatial and angular control with coherent manipulation of the NV spin and fluorescence lifetime measurements near an integrated photonic system, we demonstrate individual optically trapped NV centres as a novel route for both three-dimensional vectorial magnetometry and sensing of the local density of optical states.