1 J, 0.5 kHz repetition rate picosecond laser

Demonstration of a 1 TW peak power, joule-level ultrashort Tm:YLF laser

We report on the demonstration of a diode-pumped, Tm:YLF-based, chirped pulse amplification laser system operating at λ ≈ 1.9 µm that produces amplified pulse energies exceeding 1.5 J using a single 8-pass power amplifier. The amplified pulses are subsequently compressed to sub-300 fs durations by a diffraction grating pair, producing record >1 TW peak power pulses. To the best of our knowledge, this is the highest peak power demonstrated for any solid-state, near-2 µm laser architecture and illustrates the potential of Tm:YLF for the next generation of high-power, diode-pumped ultrashort lasers.

Kerr-lens mode-locked femtosecond Yb:CALYO oscillator with more than 20-W average power

We report on the demonstration of a pure Kerr-lens mode-locked Yb:CALYO laser which can directly deliver sub-200 fs pulses with more than 20-W average power. With an incident pump power of 89 W, 153-fs pulses were generated with an average power of 21.5 W at a repetition rate of 77.9 MHz. The corresponding peak power and single pulse energy were 1.6 MW and 0.27 µJ, respectively. The stable operation of the mode-locking was confirmed by very small fluctuations in both spectrum and output power recorded over an hour. Second harmonic generation (SHG) was conducted with 59% conversion efficiency, which indicated that the high-power mode-locking pulses are of good quality. Stable Kerr-lens mode-locking (KLM) with 156-fs pulse duration and 27.2-W average power was also achieved with 109-W pump power. To the best of our knowledge, this is the highest average output power ever reported from a femtosecond mode-locked bulk oscillator.

Recent Development of High-Energy Short-Pulse Lasers with Cryogenically Cooled Yb:YAG

High-power solid-state lasers are among the hot research directions at the forefront of laser research and have major applications in industrial processing, laser-confined nuclear fusion, and high-energy particle sources. In this paper, the properties of Yb:YAG and Nd:YAG crystals as gain media for high-power solid-state lasers were briefly compared, according to the results of which Yb:YAG crystals are more suitable for high-power applications. Then, the effects of the thermodynamic and spectral properties of Yb:YAG crystals with temperature were analyzed in detail, and it was shown that the laser beams amplified by the cryogenically cooled Yb:YAG crystals could have higher beam quality, higher pump absorption efficiency, lower pump threshold, and higher gain. The change in properties of Yb:YAG crystal at low temperature makes it more suitable as a gain medium for high-power lasers. Subsequently, two types of kilowatt-class lasers using cryogenically cooled Yb:YAG crystals as gain media are introduced—100 J, 10 Hz nanosecond lasers and 1 J, 1 kHz picosecond lasers. Their configuration, main parameters, and typical output results were analyzed. Finally, future directions in the development of cryogenically cooled Yb:YAG lasers are discussed.

Thermo-Optical Studies of Laser Ceramics

A cycle of works on manufacturing and studying laser and magnetooptical ceramics with a focus on their thermo-optical characteristics performed by the research team is analyzed. Original results that have not been published before such as measurements of the Verdet constant in the Zr:TAG, Re:MgAl₂O₄, and ZnAl₂O₄ ceramics are also presented.

Modelling and measurement of thermal stress-induced depolarisation in high energy, high repetition rate diode-pumped Yb:YAG lasers

In this paper, we present a model to predict thermal stress-induced birefringence in high energy, high repetition rate diode-pumped Yb:YAG lasers. The model calculates thermal depolarisation as a function of gain medium geometry, pump power, cooling parameters, and input polarisation state. We show that model predictions are in good agreement with experimental observations carried out on a DiPOLE 100 J, 10 Hz laser amplifier. We show that single-pass depolarisation strongly depends on input polarisation state and pumping parameters. In the absence of any depolarisation compensation scheme, depolarisation varies over a range between 5% and 40%. The strong dependence of thermal stress-induced depolarisation on input polarisation indicates that, in the case of multipass amplifiers, the use of waveplates after every pass can reduce depolarisation losses significantly. We expect that this study will assist in the design and optimisation of Yb:YAG lasers.

70 mJ nonlinear compression and scaling route for an Yb amplifier using large-core hollow fibers

In this Letter, we investigate the energy-scaling rules of hollow-core fiber (HCF)-based nonlinear pulse propagation and compression merged with high-energy Yb-laser technology, in a regime where the effects such as plasma disturbance, optical damages, and setup size become important limiting parameters. As a demonstration, 70 mJ 230 fs pulses from a high-energy Yb laser amplifier were compressed down to 40 mJ 25 fs by using a 2.8-m-long stretched HCF with a core diameter of 1 mm, resulting in a record peak power of 1.3 TW. This work presents a critical advance of a high-energy pulse (hundreds of mJ level) nonlinear interactions platform based on high energy sub-ps Yb technology with considerable applications, including driving intense THz, X-ray pulses, Wakefield acceleration, parametric wave mixing and ultraviolet generation, and tunable long-wavelength generation via enhanced Raman scattering.

1.1 J Yb:YAG picosecond laser at 1 kHz repetition rate

We demonstrate the generation of 1.1 J pulses of picosecond duration at 1 kHz repetition rate (1.1 kW average power) from a diode-pumped chirped pulse amplification Yb:YAG laser. The laser employs cryogenically cooled amplifiers to generate λ=1030nm pulses with average power of up to 1.26 kW prior to compression with excellent beam quality. Pulses are compressed to 4.5 ps duration with 90% efficiency. This compact picosecond laser will enable a variety of applications that require high energy ultrashort pulses at kilohertz repetition rates.

Demonstration of a kilowatt average power, 1 J, green laser

A λ=515nm laser generating joule-level pulses at 1 kHz repetition rate was demonstrated by frequency doubling 1.2 J, 2 ns temporally shaped square pulses from a cryogenically cooled Yb:YAG laser in an LBO crystal. A doubling efficiency of 78% resulted in 0.94 J second-harmonic pulses at 1 kHz. The unconverted light interacted with a second LBO crystal to generate >100mJ second-harmonic pulses to reach a total green average power of 1.04 kW. A conversion efficiency of 89% was achieved for 0.58 J green pulses at 1 kHz. These results open the possibility to pump high energy femtosecond lasers at kilohertz repetition rates.

High-field mid-infrared pulses derived from frequency domain optical parametric amplification

We present a novel, to the best of our knowledge, approach for scaling the peak power of mid-infrared laser pulses with few-cycle duration and carrier-to-envelope phase stabilization. Using frequency domain optical parametric amplification (FOPA), selective amplification is performed on two spectral slices of broadband pulses centered at 1.8 µm wavelength. In addition to amplification, the Fourier plane is used for specific pulse shaping to control both the relative polarization and the phase/delay between the two spectral slices of the input pulses. At the output of the FOPA, intrapulse difference frequency generation provides carrier-envelope phase stabilized two-cycle pulses centered at 9.5 µm wavelength with 25.5 µJ pulse energy. The control of the carrier-envelope phase is demonstrated through the dependence of high-harmonic generation in solids. This architecture is perfectly adapted to be scaled in the future to high average and high peak powers using picosecond ytterbium laser technologies.

Novel method for the angular chirp compensation of passively CEP-stable few-cycle pulses

We demonstrate a novel, energy-efficient, cost-effective simple method for seeding CEP-stable OPCPAs. We couple the CEP-stable idler of a broadband OPCPA into a hollow core Kagome fiber thus compensating for the angular chirp. We obtain either relatively narrow bandwidths with ∼36% coupling efficiency or quarter-octave spanning bandwidths with ∼2.2% coupling efficiency. We demonstrate spectral compressibility, good beam quality and CEP stability. Our source is an ideal seed for high-energy, high-average power, CEP-stable few-cycle OPCPA pulses around 2 µm, which can drive the generation of coherent soft X-ray radiation in the water window spectral region via HHG.

Multi-octave, CEP-stable source for high-energy field synthesis

The development of high-energy, high-power, multi-octave light transients is currently the subject of intense research driven by emerging applications in attosecond spectroscopy and coherent control. We report on a phase-stable, multi-octave source based on a Yb:YAG amplifier for light transient generation. We demonstrate the amplification of a two-octave spectrum to 25 μJ of energy in two broadband amplification channels and their temporal compression to 6 and 18 fs at 1 and 2 μm, respectively. In this scheme, due to the intrinsic temporal synchronization between the pump and seed pulses, the temporal jitter is restricted to long-term drift. We show that the intrinsic stability of the synthesizer allows subcycle detection of an electric field at 0.15 PHz. The complex electric field of the 0.15-PHz pulses and their free induction decay after interaction with water molecules are resolved by electro-optic sampling over 2 ps. The scheme is scalable in peak and average power.

High beam quality and high peak power Yb:YAG/Cr:YAG microchip laser

The prospect for developing a passively Q-switched Yb:YAG/Cr:YAG monolithic microchip laser that operates at cryogenic temperature is theoretically analyzed. It is concluded that such a system has the potential to deliver laser pulses with improved energy and increased peak power in comparison with composite Yb:YAG/Cr:YAG or Nd:YAG/Cr:YAG devices that are operated at room temperature. Consequently, a cryogenically cooled Yb:YAG/Cr:YAG system is built and the emission performances are investigated. Laser pulses with 3.2 mJ energy, 6.1 MW peak power and high beam quality of M² = 1.8 are achieved. By increasing the pump beam diameter, laser pulses with higher energy 32 mJ are obtained at 25 MW peak power with M² = 5.4. To our knowledge, these are the best results obtained from passively Q-switched composite Yb:YAG/Cr:YAG monolithic microchip lasers.

2.5 TW, two-cycle IR laser pulses via frequency domain optical parametric amplification

Broadband optical parametric amplification in the IR region has reached a new milestone through the use of a non-collinear Frequency domain Optical Parametric Amplification system. We report a laser source delivering 11.6 fs pulses with 30 mJ of energy at a central wavelength of 1.8 μm at 10 Hz repetition rate corresponding to a peak power of 2.5 TW. The peak power scaling is accompanied by a pulse shortening of about 20% upon amplification due to the spectral reshaping with higher gain in the spectral wings. This source paves the way for high flux soft X-ray pulses and IR-driven laser wakefield acceleration.

Matrix multi-pass scheme disk amplifier

Two multi-pass optical schemes of a disk laser amplifier have been proposed. Different variants of both the schemes with the smallest amount of optical elements and a lens in the active element taken into account have been calculated. For 64 passes of radiation through the active element, the average power of ∼50  W with ∼10% optical-to-optical efficiency in a pulse-periodic regime with a repetition rate of 10 kHz and a pulse duration of 2 ns was obtained at the amplifier output. The small signal gain amounted to 200.

Advances in High-Power, Ultrashort Pulse DPSSL Technologies at HiLASE

The development of kW-class diode-pumped picosecond laser sources emitting at various wavelengths started at the HiLASE Center four years ago. A 500-W Perla C thin-disk laser with a diffraction limited beam and repetition rate of 50–100 kHz, a frequency conversion to mid-infrared (mid-IR), and second to fifth harmonic frequencies was demonstrated. We present an updated review on the progress in the development of compact picosecond and femtosecond high average power radiation sources covering the ultraviolet (UV) to mid-IR spectral range at the HiLASE Center. We also report on thin-disk manufacturing by atomic diffusion bonding, which is a crucial technology for future high-power laser development.

High-energy mid-infrared sub-cycle pulse synthesis from a parametric amplifier

High-energy phase-stable sub-cycle mid-infrared pulses can provide unique opportunities to explore phase-sensitive strong-field light–matter interactions in atoms, molecules and solids. At the mid-infrared wavelength, the Keldysh parameter could be much smaller than unity even at relatively modest laser intensities, enabling the study of the strong-field sub-cycle electron dynamics in solids without damage. Here we report a high-energy sub-cycle pulse synthesiser based on a mid-infrared optical parametric amplifier and its application to high-harmonic generation in solids. The signal and idler combined spectrum spans from 2.5 to 9.0 µm. We coherently synthesise the passively carrier-envelope phase-stable signal and idler pulses to generate 33 μJ, 0.88-cycle, multi-gigawatt pulses centred at ~4.2 μm, which is further energy scalable. The mid-infrared sub-cycle pulse is used for driving high-harmonic generation in thin silicon samples, producing harmonics up to ~19th order with a continuous spectral coverage due to the isolated emission by the sub-cycle driver.

Stable sub-cycle pulses in the mid-infrared region allow damage-free investigation of electron dynamics in solids. Here, the authors develop a suitable source to this end which is based on an optical parametric amplifier.

Highly stable, 54mJ Yb-InnoSlab laser platform at 0.5kW average power

We report on the leap of Yb-InnoSlab laser technology towards high pulse energies of 54mJ combined with high average power exceeding half a kW. The system features pulse durations of 1.5 picoseconds (ps) at 10kHz repetition rate with excellent beam properties (M² of 1.1) combined with superb power and pointing stability in the sub-% range. It provides different output ports to facilitate optical synchronization for pumping parametric amplifiers. Tunable, femtosecond seed pulses are derived directly from the ps Yb pump pulses. We investigate the long term stability of this ps driven white light continuum and demonstrate 100-fold pulse compression down to 10fs duration. Ultra-broadband IR spectra centred at 2µm wavelength are subsequently generated via difference frequency generation of selected white light components.

Transverse Coherence Limited Coherent Diffraction Imaging using a Molybdenum Soft X-ray Laser Pumped at Moderate Pump Energies

Coherent diffraction imaging (CDI) in the extreme ultraviolet has become an important tool for nanoscale investigations. Laser-driven high harmonic generation (HHG) sources allow for lab scale applications such as cancer cell classification and phase-resolved surface studies. HHG sources exhibit excellent coherence but limited photon flux due poor conversion efficiency. In contrast, table-top soft X-ray lasers (SXRL) feature excellent temporal coherence and extraordinary high flux at limited transverse coherence. Here, the performance of a SXRL pumped at moderate pump energies is evaluated for CDI and compared to a HHG source. For CDI, a lower bound for the required mutual coherence factor of |μ₁₂| ≥ 0.75 is found by comparing a reconstruction with fixed support to a conventional characterization using double slits. A comparison of the captured diffraction signals suggests that SXRLs have the potential for imaging micron scale objects with sub-20 nm resolution in orders of magnitude shorter integration time compared to a conventional HHG source. Here, the low transverse coherence diameter limits the resolution to approximately 180 nm. The extraordinary high photon flux per laser shot, scalability towards higher repetition rate and capability of seeding with a high harmonic source opens a route for higher performance nanoscale imaging systems based on SXRLs.

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier

This is a report on a 100 W, 20 mJ, 1 ps Yb:YAG thin-disk regenerative amplifier. A homemade Yb:YAG thin-disk, Kerr-lens mode-locked oscillator with turn-key performance and microjoule-level pulse energy is used to seed the regenerative chirped-pulse amplifier. The amplifier is placed in airtight housing. It operates at room temperature and exhibits stable operation at a 5 kHz repetition rate, with a pulse-to-pulse stability less than 1%. By employing a 1.5 mm-thick beta barium borate crystal, the frequency of the laser output is doubled to 515 nm, with an average power of 70 W, which corresponds to an optical-to-optical efficiency of 70%. This superior performance makes the system an attractive pump source for optical parametric chirped-pulse amplifiers in the near-infrared and mid-infrared spectral range. Combining the turn-key performance and the superior stability of the regenerative amplifier, the system facilitates the generation of a broadband, CEP-stable seed. Providing the seed and pump of the optical parametric chirped-pulse amplification (OPCPA) from one laser source eliminates the demand of active temporal synchronization between these pulses. This work presents a detailed guide to set up and operate a Yb:YAG thin-disk regenerative amplifier, based on chirped-pulse amplification (CPA), as a pump source for an optical parametric chirped-pulse amplifier.

Carrier-envelope phase stable, 5.4 μJ, broadband, mid-infrared pulse generation from a 1-ps, Yb:YAG thin-disk laser

We report on a simple scheme to generate broadband, μJ pulses centered at 2.1 μm with an intrinsic carrier-envelope phase (CEP) stability from the output of a Yb:YAG regenerative amplifier delivering 1-ps pulses with randomly varying CEP. To the best of our knowledge, the reported system has the highest optical-to-optical efficiency for converting 1-ps, 1 μm pulses to CEP stable, broadband, 2.1 μm pulses. The generated coherent light carries an energy of 5.4 μJ, at 5 kHz repetition rate, that can be scaled to higher energy or power by using a suitable front end, if required. The system is ideally suited for seeding broadband parametric amplifiers and multichannel synthesizers pumped by picosecond Yb-doped amplifiers, obviating the need for active timing synchronization. Alternatively, this scheme can be combined with high-power oscillators with tens of μJ energy to generate CEP stable, multioctave supercontinua, suitable for field-resolved and time-resolved spectroscopy.

Picosecond kilohertz-class cryogenically cooled multistage Yb-doped chirped pulse amplifier

A multistage cryogenic chirped pulse amplifier has been developed, utilizing two different Yb-doped gain materials in subsequent amplifier stages. A Yb:GSAG regenerative amplifier followed by a Yb:YAG power amplifier is able to deliver pulses with a broader bandwidth than a system using only one of these two gain media throughout. We demonstrate 90 mJ of pulse energy (113 W of average power) uncompressed and 67 mJ (84 W of average power) compressed at 1.25 kHz pulse repetition frequency, 3.0 ps FWHM Gaussian pulse width, and near-diffraction-limited (M²<1.3) beam quality.

Strategies to increase laser damage performance of Ta2O5/SiO2 mirrors by modifications of the top layer design

Ta₂O₅/SiO₂ high reflection (HR) interference coatings for λ∼1  μm offer superior performance at high irradiance conditions. However, these coatings are not good candidates for high peak power conditions in comparison to HfO₂/SiO₂ multilayer stacks. Here we show that the modification of the top layers design of a quarter wave Ta₂O₅/SiO₂ high reflector leads to 4-5 fold increase in the laser damage fluence compared to a quarter wave (Ta₂O₅/SiO₂)¹⁵ when tested at λ=1.03  μm using pulse durations of 0.19 and 4 ns and peak power densities of 43.5 and 216  GW/cm². One of the designs achieved a laser damage threshold fluence of 174  J/cm² at 4 ns, which is 10% higher than that of a HfO₂/SiO₂ quarter wave design.

Near-PHz-bandwidth, phase-stable continua generated from a Yb:YAG thin-disk amplifier

We report on the generation of a multi-octave, phase-stable continuum from the output of a Yb:YAG regenerative amplifier delivering 1-ps pulses with randomly varying carrier-envelope phase (CEP). The intrinsically CEP-stable spectral continuum spans from 450 nm to beyond 2500 nm, covering a spectral range of about 0.6 PHz. The generated coherent broadband light carries an energy of 4 μJ, which can be scaled to higher values if required. The system has been designed and is ideally suited for seeding broadband parametric amplifiers and multichannel synthesizers pumped by picosecond Yb:YAG amplifiers, obviating the need for active timing synchronization required in previous approaches. The presented concept paves the way to cost-effective, reliable all-Yb:YAG single-cycle sources with terawatt peak-power and tens-of-Watts average power.