Ultrafast thulium fiber laser system emitting more than 1 kW of average power

In-band pumped, Q-switched thulium-doped fiber laser system delivering 140 W and 7 mJ pulse energy

We report on a highly efficient, in-band pumped, Q-switched, Tm-doped, rod-type master oscillator power amplifier (MOPA) system delivering up to 140 W average output power and 7 mJ pulse energy with a slope efficiency of 77% at 20 kHz repetition rate. The amplifier is pumped with Raman-shifted fiber lasers centered at 1692 nm. This in-band pump scheme for Tm-doped fiber lasers can significantly mitigate their quantum defect-related heat load limitations. At the same time, this pump wavelength yields a similar amount of storable and extractable energy to the state-of-the-art pumping at 793 nm. This approach has allowed for the development of highly efficient Tm-doped fiber laser systems combining a high average power and a high output pulse energy.

Coherent beam combining of two all-PM thulium-doped fiber chirped pulse amplifiers

In this paper, we report a coherent beam combining (CBC) system that involves two thulium-doped all-polarization maintaining (PM) fiber chirped pulse amplifiers. Through phase-locking the two channels via a fiber stretcher by using the stochastic parallel gradient descent (SPGD) algorithm, a maximum average power of 265 W is obtained, with a CBC efficiency of 81% and a residual phase error of λ/17. After de-chirping by a pair of diffraction gratings, the duration of the combined laser pulse is compressed to 690 fs. Taking into account the compression efficiency of 90% and the main peak energy proportion of 91%, the corresponding peak power is calculated to be 4 MW. The laser noise characteristics before and after CBC are examined, and the results indicate that the CBC would degrade the low frequency relative intensity noise (RIN), of which the integration is 1.74% in [100 Hz, 2 MHz] at the maximum combined output power. In addition, the effects of the nonlinear spectrum broadening during chirped pulse amplification on the CBC efficiency are also investigated, showing that a higher extent of pulse stretching is effective in alleviating the spectrum broadening and realizing a higher output power with decent combining efficiency.

5.4 W, 2.35 µm cascaded Raman fiber laser pumped by dissipative soliton resonance-like pulses

We present a nonlinear amplifying loop mirror-based mode-locked fiber laser. By adjusting the pump power, the proposed laser exhibits a dissipative soliton resonance (DSR)-like pulse operation with a maximum pulse width of 150 ns. Subsequently, a three-stage Tm3+-doped fiber amplifier is implemented using a single-mode double-cladding Tm3+-doped fiber to increase the DSR-like pulse output power to 52.5 W, achieving a pump slope efficiency of 47.1% in the main amplifier. A 25 m first-order Raman-gain fiber (UHNA7) is pumped by a DSR-like pulse, and 16.3 W of pure 2.135 µm first-order Raman light with a spectral purity of 73.4% is obtained. Finally, 5.4 W of 2.35 µm second-order Raman light with a spectral purity of 66% is obtained using a 10 m 98% germania-core fiber as a second-order Raman-gain fiber cascaded after UHNA7 fiber. To the best of our knowledge, this is the highest output power ever obtained from a 2.3 µm laser.

Temperature investigation of low SWaP thulium-doped fiber lasers

We investigate the temperature dependence of an in-band core-pumped thulium-doped fiber laser with a low SWaP (size, weight, and power) architecture. The temperature investigation is carried out both experimentally and numerically by a simulation model. We demonstrate experimentally that the investigated setup is resistant for temperatures till 353 K. In addition, we explain the observed behavior by considering the temperature depended spectroscopic parameters of thulium-doped silica fibers. Finally, a numerical investigation is carried out for higher temperatures up to 573 K and higher output powers up to 12 W as well as for different wavelengths and show that the considered fiber lasers works still efficient at these temperature ranges. We show the reliability of the considered thulium-doped fiber laser architecture for applications in harsh environment.

Development of pedestal-free large mode area fibers withTm3+ doped silica nanostructured core

We present the pedestal-free thulium doped silica fiber with a large nanostructured core optimized for fiber lasers. The fiber is composed of over 6 thousand thulium doped silica nanorods with a diameter of 71 nm each which form a nanostructured step-index core. We study the influence of non-continuous distribution in nanoscale active areas on gain, beam quality, and fiber laser performance. The proof-of-concept fiber is effectively single mode for wavelength above 1.8 µm. We demonstrate the performance of the fiber in a laser setup pumped at 792 nm. Single mode laser emission with a slope efficiency of 29% at quasi-continuous output power of 4 W with M2 = 1.3 at the emission spectrum 1880-1925 nm is achieved.

Monolithic 2-µm single-frequency linearly-polarized gain-switched distributed feedback fiber laser by femtosecond laser direct-writing

We report a single-frequency, linearly polarized gain-switched, distributed feedback (DFB), 2-µm thulium doped silica fiber laser (TDFL), with an effective cavity length of 2.5 mm. The cavity is based on a heavily thulium doped non-polarization-maintaining silica fiber and composed of a π-phase-shifted fiber Bragg grating (FBG) with a total FBG length of 35 mm. The DFB FBG was written by femtosecond-laser point-by-point (PbP) method. In-band pumping scheme is chosen with a 1550 nm nanosecond pulsed erbium-doped silica fiber laser pump. Single-longitudinal, linearly polarized, gain-switched TDFL at 2002 nm, with a recorded shortest pulse duration of 4.7 ns, a repetition rate of 20 kHz, a maximum peak power of 170 W, and single pulse energy of 0.8 µJ, has been obtained, benefitting from the ultrashort DFB cavity made by the femtosecond laser direct-writing method.

100 W, tunable in-band thulium fiber amplifier pumped by incoherently combined 1.9 µm fiber lasers

We detail the design and performance of a high efficiency in-band pumped thulium fiber amplifier operating at the 100 W level. Using a novel pumping architecture based on three incoherently combined thulium fiber oscillators at 1904 nm and a seed laser tunable from 1970-1990 nm, efficient amplification is demonstrated in a high dopant concentration 25/65/250 µm thulium fiber. Here we use the 65 µm pedestal surrounding the core as a pump cladding to increase the cladding to core overlap and improve the overall pump absorption. Up to 89% slope efficiency is obtained with ∼100 W output power at 1990 nm. These results indicate that in-band pumping is a viable route to circumvent the thermal limitations associated with 793 nm diode pumping and provide a pathway for development of multi-kW laser sources in the 2 µm spectral window.

Widely-tunable all-fiber Tm doped MOPA with > 1 kW of output power

In this paper, we report on a high-power and widely tunable thulium-doped fiber laser (TDFL) based on a monolithic master oscillator power amplifier (MOPA) system. The master oscillator is a Tm fiber ring laser incorporating a tunable bandpass filter to realize narrow linewidth and wavelength tunable operation. The MOPA generated 1010 W ∼1039 W of output power over a tuning range of 107 nm from 1943 to 2050nm with slope efficiencies of more than 51% and spectra linewidth of ∼0.5 nm. Power stability (RMS) in ∼10 min scale is measured to be ∼0.52%. A diffraction-limited beam quality factor M² of ∼1.18 is measured at 920 W of laser output. Output power is pump-limited without the onset of parasitic oscillation or amplified spontaneous emission (ASE) even at the maximum power level. This is the first demonstration, to the best of our knowledge, on an all-fiber integrated wavelength-tunable TDFL at 2 µm with output power exceeding 1 kW.

High-power two-color plasma-based THz generation driven by a Tm-doped fiber laser

We report on the efficient generation of broadband THz radiation based on a two-color gas-plasma scheme. Broadband THz pulses covering the whole THz spectral region, from 0.1-35 THz, are generated. This is enabled by a high-power, ultra-fast, thulium-doped, fiber chirped pulse amplification (Tm:FCPA) system and a subsequent nonlinear pulse compression stage that uses a gas-filled capillary. The driving source delivers 40 fs pulses at a central wavelength of 1.9 μm with 1.2 mJ pulse energy and 101 kHz repetition rate. Owing to the long driving wavelength and the use of a gas-jet in the THz generation focus, the highest reported conversion efficiency for high-power THz sources (>20 mW) of 0.32% has been achieved. The high efficiency and average power of 380 mW of the broadband THz radiation make this an ideal source for nonlinear, tabletop THz science.

Nonlinear pulse compression to sub-two-cycle, 1.3 mJ pulses at 1.9 μm wavelength with 132 W average power

We report the nonlinear pulse compression of a high-power, thulium-doped fiber laser system using a gas-filled hollow-core fiber. The sub-two cycle source delivers 1.3 mJ pulse energy with 80 GW peak power at a central wavelength of 1.87 μm and an average power of 132 W. This is, so far, to the best of our knowledge, the highest average power of a few-cycle laser source reported in the short-wave infrared region. Given its unique combination of high pulse energy and high average power, this laser source is an excellent driver for nonlinear frequency conversion, toward terahertz, mid-infrared, and soft X-ray spectral regions.

Temperature-dependent cross section spectra for thulium-doped fiber lasers

An investigation on the temperature dependence of spectroscopic parameters of trivalent thulium ions is important for the design of high-power, thulium-doped fiber lasers and amplifiers. In this Letter, the thulium absorption/emission cross sections are determined in the spectral range 700-2200 nm and in the temperature range from -196°C to 300°C. The spectra are obtained from the absorption and emission measurements of a thulium-doped fiber and from measured thulium concentration profiles. Attempts were made to estimate the temperature dependence of the spectra where the measurements are not accessible. Firstly, the spectra are fitted to a multi-Gaussian model with temperature dependent parameters. Secondly, a physically motivated model of the cross section spectra is proposed and analyzed.

Inband-pumped, high-power thulium-doped fiber amplifiers for an ultrafast pulsed operation

We investigate the influence of the pump wavelength on the high-power amplification of large-mode area, thulium-doped fibers which are suitable for an ultrashort pulsed operation in the 2 µm wavelength region. By pumping a standard, commercially available photonic crystal fiber in an amplifier configuration at 1692 nm, a slope efficiency of 80 % at an average output power of 60 W could be shown. With the help of simulations we investigate the effect of cross-relaxations on the efficiency and the thermal behavior. We extend our investigations to a rod-type, large-pitch fiber with very large mode area, which is exceptionally suited for high-energy ultrafast operation. Pumping at 1692 nm leads to a slope efficiency of 74 % with a average output power of 67 W, instead of the 38 % slope efficiency obtained when pumping at 793 nm. These results pave the way to highly efficient 2 µm fiber-based CPA systems.

Simulation and compensation of thermal lensing in optical systems

High-power optical systems are used in a number of industrial applications. One difficulty in designing such systems is that the beam itself is a significant source of heat, which changes the optical properties of the system. To reduce this effect, we propose a new thermal lensing compensation technique based on a detailed analysis of the optical properties of the high-power optical system. To this end, we have developed a new ray tracing simulation technique that accurately models optical propagation through inhomogeneous, anisotropic, and deformed media. This model enables the performance of systems in physically realistic situations to be evaluated efficiently. Experimental comparisons were conducted to validate the simulation. We found excellent agreement between the simulation and the measured data. We have validated the simulation technique for a single lens setup and a complex optical scanner system.

50-W average power Ho:YAG SESAM-modelocked thin-disk oscillator at 2.1 µm

Ultrafast laser systems operating with high-average power in the wavelength range from 1.9 µm to 3 µm are of interest for a wide range of applications for example in spectroscopy, material processing and as drivers for secondary sources in the XUV spectral region. In this area, laser systems based on holmium-doped gain materials directly emitting at 2.1 µm have made significant progress over the past years, however so far only very few results were demonstrated in power-scalable high-power laser geometries. In particular, the thin-disk geometry is promising for directly modelocked oscillators with high average power levels that are comparable to amplifier systems at MHz repetition rate. In this paper, we demonstrate semiconductor saturable absorber mirror (SESAM) modelocked Ho:YAG thin-disk lasers (TDLs) emitting at 2.1-µm wavelength with record-holding performance levels. In our highest average power configuration, we reach 50 W of average power, with 1.13-ps pulses, 2.11 µJ of pulse energy and ∼1.9 MW of peak power. To the best of our knowledge, this represents the highest average power, as well as the highest output pulse energy so far demonstrated from a modelocked laser in the 2-µm wavelength region. This record performance level was enabled by the recent development of high-power GaSb-based SESAMs with low loss, adapted for high intracavity power and pulse energy. We also explore the limitations in terms of reaching shorter pulse durations at high power with this gain material in the disk geometry and using SESAM modelocking, and present first steps in this direction, with the demonstration of 30 W of output power, with 692-fs pulses in another laser configuration. In the near future, with the development of a next generation of SESAM samples for this wavelength region, we believe higher pulse energy approaching the 10-µJ regime, and sub-500-fs pulses should be straightforward to reach using SESAM modelocking.

Nonlinear pulse compression to 51-W average power GW-class 35-fs pulses at 2-µm wavelength in a gas-filled multi-pass cell

We report on the generation of GW-class peak power, 35-fs pulses at 2-µm wavelength with an average power of 51 W at 300-kHz repetition rate. A compact, krypton-filled Herriott-type cavity employing metallic mirrors is used for spectral broadening. This multi-pass compression stage enables the efficient post compression of the pulses emitted by an ultrafast coherently combined thulium-doped fiber laser system. The presented results demonstrate an excellent preservation of the input beam quality in combination with a power transmission as high as 80%. These results show that multi-pass cell based post-compression is an attractive alternative to nonlinear spectral broadening in fibers, which is commonly employed for thulium-doped and other mid-infrared ultrafast laser systems. Particularly, the average power scalability and the potential to achieve few-cycle pulse durations make this scheme highly attractive.

Ultrafast Tm-doped fiber laser system delivering 1.65-mJ, sub-100-fs pulses at a 100-kHz repetition rate

High-energy, ultrafast, short-wavelength infrared laser sources with high average power are important tools for industrial and scientific applications. Through the coherent combination of four ultrafast thulium-doped rod-type fiber amplifiers, we demonstrate a Tm-doped chirped pulse amplification system with a compressed pulse energy of 1.65 mJ and 167 W of average output power at a repetition rate of 101 kHz. The system delivers 85 fs pulses with a peak power of 15 GW. Additionally, the system presents a high long- and short-term stability. To the best of our knowledge, this is the highest average output power short wavelength IR, mJ-class source to date. This result shows the potential of coherent beam combining techniques in the short wavelength infrared spectral region for the power scalability of these systems.

Laser-pulse-induced temperature, thermal stress, and crater morphology effect during multipulse nanosecond laser manufacturing

We construct a numerical model for multipulse laser drilling. It is found that the previous laser-pulse-induced temperature accumulation, thermal stress occurrence, and crater morphology change promote subsequent pulse laser drilling. Among them, previous laser-pulse-induced temperature accumulation contributes significantly to the drilled crater depth when the workpiece temperature is higher than its melting point just before the subsequent laser pulse irradiation, especially in a short pulse interval condition. The crater morphology change becomes the main contributor when the workpiece temperature decreases below the melting point, often in a long pulse interval condition. Besides, the previous occurrence of laser-pulse-induced thermal stress always has had little influence on the drilled crater. This work can be a theoretical reference, especially for multipulse laser manufacturing.

Fiber-laser platform for precision brain surgery

Minimally invasive neurological surgeries are increasingly being sought after for treatment in neurological pathologies and oncology. A critical limitation in these minimally invasive procedures is lack of specialized tools that allow for space-time controlled delivery of sufficient energy for coagulation and cutting of tissue. Advent of fiber-lasers provide high average power with improved beam quality (lower M²), biocompatible silica fiber delivery, reduced cost of manufacturing, and radiant output stability over long operating periods. Despite these advancements, no fiber-laser based surgical tools are currently available for tissue resection in vivo. Here we demonstrate a first to our knowledge, fiber-laser platform for performing precise brain surgery in a murine brain model. In this study, our primary aims were to first demonstrate efficacy of fiber-lasers in performing precise blood-less surgery in a murine brain with limited non-specific thermal damage. Second, fiber-lasers' ability to deliver radiant energy through biocompatible silica fibers was explored in a murine brain model for blood less resection. A bench-top optical coherence tomography (OCT) guided fiber-laser platform was constructed with a stereotactic stage for performing precision brain surgery. A pulsed quasi-continuous wave ytterbium (Yb) fiber-laser (1.07 µm) was used to perform vascular specific coagulation while a pulsed nanosecond thulium fiber-laser (1.94 µm) was used to conduct bloodless cutting, all under the guidance of a swept-source OCT system centered at 1310 +/- 70 nm. Specialty linear and circular cuts were made in an in vivo murine brain for bloodless brain tissue resection. The two fiber-lasers were combined into a single biocompatible silica fiber to conduct brain surgery resection under the bench-top OCT system's imaging microscope. Vascular specific coagulation was demonstrated in all five mice studied. Bloodless linear cuts and point cuts were demonstrated in vivo. Histologically, thermal injury was measured to be less than 100 µm while a removal rate of close to 5 mm³/s was achieved with an average Tm fiber-laser power of 15 W. To the authors' knowledge, this is the first demonstration of a fiber-laser platform for conducting in vivo bloodless brain tissue resection with a pulsed thulium (Tm) fiber-laser and a quasi-continuous wave (QCW) Yb fiber-laser. The demonstrated fiber-laser platform, if successfully configured for use in the operating room (OR), can provide surgeons a tool for rapid removal of tissue while making surgical resections of brain regions more precise, and can be basis for a flexible cutting tool capable of reaching hard-to-operate regions.

Damage thresholds of silicon-based cameras for in-band and out-of-band laser expositions

The damage threshold of silicon-based cameras to laser irradiation is measured for continuous wave lasers at both in-band and out-of-band wavelengths. Clarifications about the various kinds of damage reported in the literature are also presented and explained through various tests. For increasing laser intensities, the sequence of laser effects on cameras usually starts from dazzling, to a decrease of the pixel response up to the complete neutralization of its pixel matrix. However, the intensity range for the complete sequence of these laser effects can strongly depend on the laser wavelengths and the tested cameras, particularly for out-of-band laser wavelengths. The proposed definitions of damage thresholds presented in this work offer a basis for the future comparison of results between different studies.

Low loss nested hollow-core anti-resonant fiber at 2 µm spectral range

We report the fabrication and characterization of a five-tube nested hollow-core anti-resonant fiber (Nested HC-ARF), which exhibits outstanding optical performance in terms of a record attenuation value of 0.85 dB/km at 2 µm wavelength range with a 200 nm bandwidth below 2 dB/km and excellent modal purity. The power handling capability of the Nested HC-ARF is also demonstrated in this work. Pulses of 75 W, 160 ps from the thulium-doped fiber laser are delivered using a 6-m-long fabricated Nested HC-ARF. The tested fiber is coiled into a 20 cm bending radius and achieves a coupling efficiency of 86.7%. The maximum average power of 60.5 W is transmitted through our Nested HC-ARF in a robust single-mode fashion without introducing any damage to the input and output fiber end-faces, which demonstrates the superior ability of such a fiber for high-power laser delivery.

1.7 µm Tm-fiber chirped pulse amplification system with dissipative soliton seed laser

We report on a 1.7 µm Tm-fiber chirped pulse amplification (CPA) system by virtue of a broadband dissipative soliton seed laser. The seed oscillator delivers the dissipative soliton with 10 dB spectral bandwidth of 23 nm and an average power of 4 mW. The duration of the seed pulse is directly stretched to ∼60ps by a segment of 50 m normal dispersion fiber. Using a two-stage fiber amplifier, the average power of the pulse is amplified to 1.95 W with a slope efficiency of 40.3%. The amplified pulse is then compressed to 348 fs by a pair of fused silica transmission gratings. The compressed average power of 1.3 W and peak power of 155 kW are achieved. These experimental results would pave the way to achieve a high-power femtosecond laser source at 1.7 µm, which could find important applications in fields such as three-photon deep-tissue imaging and material processing.

High-power modelocked thin-disk oscillators as potential technology for high-rate material processing

High average power femtosecond lasers have made spectacular progress in the last decades - moving from laboratory-based systems with maximum average powers of tens of watts to kilowatt-class mature industrial systems in a short time. The availability of such systems opens new possibilities in many fields; one of the most prominent ones that have driven many of these technological advances is precise high-speed material processing, where ultrashort pulses have long been recognized to provide highest precision processing of virtually any material, and high average power extends these capabilities to highest processing rates. Here, we focus our attention on one high-average power technology with large unexplored potential for this specific application: directly modelocked multi-MHz repetition frequency high-power thin-disk oscillators. We review their latest state-of-the-art and discuss future directions and challenges, specifically with this application field in mind.

Tm:YAG single-crystal fiber laser

In this Letter, to the best of our knowledge, we present the first thulium (Tm) single-crystal fiber (SCF) laser with free-space propagation of the laser beam only. The SCF is equipped with diffusion-bonded end caps of undoped YAG for better thermal management and enhancement of pump guiding. By utilizing mode matching and pump guiding in different SCF parts, an output power of 9.1 W is achieved at ∼2.02µm with a slope efficiency of 49.4%. This straightforward approach, which is also simple to realize and is based on combining the advantages of fiber-geometry structure and crystalline properties of Tm:YAG, is expected to be useful for 2 µm amplification stages in different time formats as well.

Compact chirped-pulse amplification systems based on highly Tm3+-doped germanate fiber

We report the fabrication of a dual cladding large mode area thulium-doped germanate fiber (TDGF). The fiber has a core diameter of 20 µm, a high Tm³⁺ ion concentration of 3cm³×10²⁰/cm³, and a hexagonal inner cladding to enhance pump absorption when cladding-pumped. Using a short fiber length, we demonstrate a compact 300 fs chirped-pulse amplification system operating at 1925 nm, investigating both core- and cladding-pumped implementations. By cladding pumping a 65 cm long fiber we produced an average power of 14.1 W (limited by thermally induced damage) and a peak power of 2.17 MW at a pulse repetition rate of 15.7 MHz. Core pumping a 19 cm length of TDGF produced 2.3 W of average-power and 16 MW peak-power pulses at 0.39 MHz. The performance is already comparable to the state-of-the-art success achieved with flexible silica fibers. Considering the rapid improvements in glass quality and the scope for further increasing the doping concentration, this fiber type holds great potential for pulsed fiber lasers in the 1.5-3 µm wavelength region.

Review on Experimental and Theoretical Investigations of Ultra-Short Pulsed Laser Ablation of Metals with Burst Pulses

Laser processing with ultra-short double pulses has gained attraction since the beginning of the 2000s. In the last decade, pulse bursts consisting of multiple pulses with a delay of several 10 ns and less found their way into the area of micromachining of metals, opening up completely new process regimes and allowing an increase in the structuring rates and surface quality of machined samples. Several physical effects such as shielding or re-deposition of material have led to a new understanding of the related machining strategies and processing regimes. Results of both experimental and numerical investigations are placed into context for different time scales during laser processing. This review is dedicated to the fundamental physical phenomena taking place during burst processing and their respective effects on machining results of metals in the ultra-short pulse regime for delays ranging from several 100 fs to several microseconds. Furthermore, technical applications based on these effects are reviewed.

Transverse mode instability and thermal effects in thulium-doped fiber amplifiers under high thermal loads

We experimentally analyze the average-power-scaling capabilities of ultrafast, thulium-doped fiber amplifiers. It has been theoretically predicted that thulium-doped fiber laser systems, with an emission wavelength around 2 µm, should be able to withstand much higher heat-loads than their Yb-doped counterparts before the onset of transverse mode instability (TMI) is observed. In this work we experimentally verify this theoretical prediction by operating thulium doped fibers at very high heat-load. In separate experiments we analyze the performance of two different large-core, thulium-doped fiber amplifiers. The first experiment aims at operating a short, very-large core, thulium-doped fiber amplifier at extreme heat-load levels of more than 300 W/m. Even at this extreme heat-load level, the onset of TMI is not observed. The second experiment maximizes the extractable average-output power from a large-core, thulium-doped, fiber amplifier. We have achieved a pump-limited average output power of 1.15 kW without the onset of TMI. However, during a longer period of operation at this power level the amplifier performance steadily degraded and TMI could be observed for average powers in excess of 847 W thereafter. This is the first time, to the best of our knowledge, that TMI has been reported in a thulium-doped fiber amplifier.

Moving towards high-power thin-disk lasers in the 2 µm wavelength range

Thin-disk lasers (TDLs) have made spectacular progress in the last decades both in continuous-wave (CW) and ultrafast operation. Nowadays, single thin-disk oscillators with >16 kW of CW-power have been demonstrated and ultrafast amplifiers have largely surpassed the kilowatt milestone with pulse energies in the multi-100 mJ range. This amazing development has been demonstrated in the 1 µm wavelength range, using Yb-doped materials and supported by industrially available components. Motivated by both strong scientific and industrial applications, interest in expanding this performance to longer wavelength regions continues to increase. In particular, TDLs emitting directly in the short-wave mid-infrared (SW-MIR) region (2–3 µm) are especially sought after, and although many early studies have been reported, most remained in the proof-of-principle stage and the potential for multi-100 W operation remained undemonstrated. Here, we report on our recent results of a single fundamental-mode CW Ho:YAG thin-disk oscillator with >100 W of power, surpassing previous single-mode TDLs by a factor of >4, and marking a first milestone in the development of high-power SW-MIR TDLs. In optimized conditions, our laser system emitting at ≈2.1 µm reaches an output power of 112 W with 54.6% optical-to-optical efficiency and an M 2 = 1.1. This system is ideally suited for future direct modelocking at the 100 W level, as well as for ultrafast amplification. We start the discussion with a review of the state-of-the-art of TDLs emitting directly in the vicinity of 2 µm, and then discuss difficulties and possible routes both towards ultrafast operation and next possible steps for power scaling.

Over 10 W linearly polarized supercontinuum directly produced in an erbium-doped fiber MOPA seeded with stretched soliton

We experimentally achieve over 10 W linearly polarized supercontinuum (SC) generation in a polarization-maintaining (PM) erbium-doped fiber (EDF) master oscillator power-amplifier (MOPA). The house-built PM seeding EDF laser can deliver ∼209fs soliton around ∼1563.7nm, which is then stretched to >15ps using a long piece of normal-dispersion fiber. The wideband spectrum of the ultrashort seeding soliton facilitates the further spectral broadening with nonlinear effects. The soliton stretching decelerates the peak power increase, thus facilitating higher amplified average power. After several stages of pre-amplification, the stretched soliton is fed into the main amplifier constructed with PM large mode area fibers. The output average power is finally amplified to ∼11.51W. The corresponding spectrum spans from ∼1450 to ∼2200nm, indicating that SC is formed due to the induced strong nonlinear effects. The polarization extinction ratio at the output reaches over 18 dB. The PM characteristic potentially enhances the system's resistance to environmental disturbances and eliminates instabilities relating to polarization-mode coupling. Our result represents, so far, the highest SC power directly produced in an EDF MOPA, to the best of our knowledge, especially in a linearly polarized manner. This also suggests a scheme for powerful SC generation that employs direct laser diode pumping and duration-managed pulse seeding.

Active Optical Fibers and Components for Fiber Lasers Emitting in the 2-μm Spectral Range

Laser sources emitting in the infrared range at around 2 µm are attracting great interest for a variety of applications like processing of transparent thermoplastic polymers in industry as well as plenty of applications in medicine, spectroscopy, gas sensing, nonlinear frequency conversion to the mid-infrared, to mention a few. Of late, fiber lasers compared to other kinds of lasers benefit from their all-fiber design, leading to a compact, robust, and well thermally manageable device. Particularly, thulium- and holmium-doped fiber lasers are the first choice in fiber lasers emitting light around 2 µm. In this paper, we give an overview of our recent results in the research on thulium- and holmium-doped optical fibers, fiber lasers, and related research topics in the 2-µm spectral range. In particular, we present, to our knowledge, the first results of improvement of pump absorption in double-clad fibers thanks to the fiber twist frozen during drawing. Finally, a brief demonstration of material processing by thulium all-fiber laser operating at 2 µm is presented.

Low noise all-fiber amplification of a coherent supercontinuum at 2 µm and its limits imposed by polarization noise

We report a low noise, broadband, ultrafast Thulium/Holmium co-doped all-fiber chirped pulse amplifier, seeded by an Erbium-fiber system spectrally broadened via coherent supercontinuum generation in an all-normal dispersion photonic crystal fiber. The amplifier supports a − 20 dB bandwidth of more than 300 nm and delivers high quality 66 fs pulses with more than 70 kW peak power directly from the output fiber. The total relative intensity noise (RIN) integrated from 10 Hz to 20 MHz is 0.07%, which to our knowledge is the lowest reported RIN for wideband ultrafast amplifiers operating at 2 µm to date. This is achieved by eliminating noise-sensitive anomalous dispersion nonlinear dynamics from the spectral broadening stage. In addition, we identify the origin of the remaining excess RIN as polarization modulational instability (PMI), and propose a route towards complete elimination of this excess noise. Hence, our work paves the way for a next generation of ultra-low noise frequency combs and ultrashort pulse sources in the 2 µm spectral region that rival or even outperform the excellent noise characteristics of Erbium-fiber technology.

Birefringent large-mode-area anti-resonant hollow core fiber in the 1.9 µm wavelength window

We report on the development and characterization of a birefringent large-mode-area anti-resonant silica fiber. The fiber structure is composed of six non-touching capillaries. The birefringence results from the breaking of the circular symmetry of an air core with increasing of the diameters of two capillaries located across the fiber diameter. We depart from earlier designs of polarizing hollow core fibers, in which coupling of the guided modes was intentionally facilitated with the cladding layout. Instead, with the help of numerical simulations, we enhance birefringence in our design by varying the capillary wall thickness between the larger- and smaller-diameter capillary sections of the cladding. The fiber has a large, elliptical core with semi-axes of ∼55 and 41 µm in diameter, an effective area of the fundamental mode of 1200µm², and a total outer diameter of 127 µm. The cladding is composed of two pairs of smaller capillaries, which are 18 µm in diameter with 1.66 µm thick walls, and two larger capillaries with a 24 µm diameter and 1.14 µm thick walls, located across the diagonal of the fiber. Measured group birefringence over 1820-1920 nm wavelengths is monotonically increasing from 0.4×10^-4 to 2.0×10^-4, while its phase birefringence is from 5×10^-6 to 1.1×10^-5. Despite this, the fiber holds polarization with a 12 dB polarization extinction ratio at 1900 nm over a 1.5 m long sample.

Compact, high repetition rate, 4.2 MW peak power, 1925 nm, thulium-doped fiber chirped-pulse amplification system with dissipative soliton seed laser

We report the demonstration of a high average- and peak-power, 1925 nm, thulium-fiber based chirped pulse amplification (CPA) system. A compact, dissipative soliton thulium-fiber, mode-locked seed produced pre-chirped pulses with 25 ps duration, 45 mW output power and repetition rate of 15.7 MHz. After stretching to 105 ps in 83 m of normal dispersion fiber, the pulses were amplified in a core-pumped pre-amplifier and a cladding pumped power amplifier to average output powers of 28 W and 30 W with forward and backward pumping, respectively, with the output power limited only by the available pump power. After a pair of fused silica transmission gratings with an efficiency of 71%, the amplified pulses were re-compressed to 297 fs yielding pulses with a peak power of 4.2 MW (backward pumped) and a pulse energy of 1.27 µJ.

Ultra low-noise coherent supercontinuum amplification and compression below 100 fs in an all-fiber polarization-maintaining thulium fiber amplifier

We report an ultra-low noise, polarization-maintaining, ultrafast Thulium-doped all-fiber chirped pulse amplifier, seeded by a polarized all-normal dispersion (ANDi) supercontinuum (SC) driven by an ultrafast Erbium-fiber laser. The system comprises only polarization-maintaining fibers and delivers 96 fs pulses with 350 mW output power at 100 MHz, centered at 1900 nm. The integrated relative intensity noise (RIN) in the range of 10 Hz - 10 MHz is only 0.047% at the amplifier output, which is virtually identical to the RIN of the Erbium-fiber laser driving the SC. Therefore, neither the SC generation nor the amplification process introduce significant excess noise. The RIN of our system is an order of magnitude lower than similar systems previously seeded with Raman solitons. This highlights the superior noise properties of ANDi SC and their potential as ultra-low noise seed sources for broadband, high power ultrafast fiber amplifiers and frequency combs.

Cavity-enhanced noncollinear high-harmonic generation

Femtosecond enhancement cavities have enabled multi-10-MHz-repetition-rate coherent extreme ultraviolet (XUV) sources with photon energies exceeding 100 eV - albeit with rather severe limitations of the net conversion efficiency and of the duration of the XUV emission. Here, we explore the possibility of circumventing both these limitations by harnessing spatiotemporal couplings in the driving field, similar to the "attosecond lighthouse," in theory and experiment. Our results predict dramatically improved output coupling efficiencies and efficient generation of isolated XUV attosecond pulses.

High-power edge-emitting laser based on a parity-time-structured Bragg reflection waveguide

A parity-time-structured Bragg reflection waveguide is proposed and analyzed for realizing a high-power laser. A single transverse mode with the optical field confined mainly in the low-index core is discussed to improve the catastrophic optical damage threshold for high output power. The designed scheme can potentially mitigate the heat buildup by moving the injection from the central narrow core to the outer large-area claddings, while suppressing the coupler mode transversely. The structure can achieve high output power with a short cavity length, low lasing threshold, and high power conversion efficiency.

Watt-scale 50-MHz source of single-cycle waveform-stable pulses in the molecular fingerprint region

We report a coherent mid-infrared (MIR) source with a combination of broad spectral coverage (6-18 μm), high repetition rate (50 MHz), and high average power (0.5 W). The waveform-stable pulses emerge via intrapulse difference-frequency generation (IPDFG) in a GaSe crystal, driven by a 30-W-average-power train of 32-fs pulses spectrally centered at 2 μm, delivered by a fiber-laser system. Electro-optic sampling (EOS) of the waveform-stable MIR waveforms reveals their single-cycle nature, confirming the excellent phase matching both of IPDFG and of EOS with 2-μm pulses in GaSe.