The mode of interfragmentary movement affects bone formation and revascularization after callus distraction

Effect of lag screw on stability of first metatarsophalangeal joint arthrodesis with medial plate

Background

First metatarsophalangeal joint (MTP-1) arthrodesis is a commonly performed procedure in the treatment of disorders of the great toe. Since the incidence of revision after MTP-1 joint arthrodesis is not insignificant, a medial approach with a medially positioned locking plate has been proposed as a new technique. The aim of the study was to investigate the effect of the application of a lag screw on the stability and strength of first metatarsophalangeal joint arthrodesis with medial plate.

Methods

The bending tests in a testing machine were performed for models of the first metatarsal bone and the proximal phalanx printed on a 3D printer from polylactide material. The bones were joined using the locking titanium plate and six locking screws. The specimens were divided into three groups of seven each: medial plate and no lag screw, medial plate with a lag screw, dorsal plate with a lag screw. The tests were carried out quasi-static until the samples failure.

Results

The addition of the lag screw to the medial plate significantly increased flexural stiffness (41.45 N/mm vs 23.84 N/mm, p = 0.002), which was lower than that of the dorsal plate with a lag screw (81.29 N/mm, p < 0.001). The similar maximum force greater than 700 N (p > 0.50) and the relative bone displacements lower than 0.5 mm for a force of 50 N were obtained for all fixation techniques.

Conclusions

The lag screw significantly increased the shear stiffness in particular and reduced relative transverse displacements to the level that should not delay the healing process for the full load of the MTP-1 joint arthrodesis with the medial plate. It is recommended to use the locking screws with a larger cross-sectional area of the head to minimize rotation of the medial plate relative to the metatarsal bone.

Weak Points of Double-Plate Stabilization Used in the Treatment of Distal Humerus Fracture through Finite Element Analysis

BACKGROUND

Multi-comminuted, intra-articular fractures of the distal humerus still pose a challenge to modern orthopedics due to unsatisfactory treatment results and a high percentage (over 50%) of postoperative complications. When surgical treatment is chosen, such fractures are fixed using two plates with locking screws, which can be used in three spatial configurations: either parallel or one of two perpendicular variants (posterolateral and posteromedial). The evaluation of the fracture healing conditions for these plate configurations is unambiguous. The contradictions between the conclusions of biomechanical studies and clinical observations were the motivation to undertake a more in-depth biomechanical analysis aiming to indicate the weak points of two-plate fracture stabilization.

METHODS

Research was conducted using the finite element method based on an experimentally validated model. Three variants of distal humerus fracture (Y, λ, and H) were fixed using three different plate configurations (parallel, posterolateral, and posteromedial), and they were analyzed under six loading conditions, covering the whole range of flexion in the elbow joint (0-145°). A joint reaction force equal to 150 N was assumed, which corresponds with holding a weight of 1 kg in the hand. The biomechanical conditions of bone union were assessed based on the interfragmentary movement (IFM) and using criteria formulated by Steiner et al. Results: The IFMs were established for particular regions of all of the analyzed types of fracture, with distinction to the normal and tangential components. In general, the tangential component of IFM was greater than normal. A strong influence of the elbow joint's angular position on the IFM was observed, with excessive values occurring for flexion angles greater than 90°. In most cases, the smallest IFM values were obtained for the parallel plaiting, while the greatest values were obtained for the posteromedial plating. Based on IFM values, fracture healing conditions in particular cases (fracture type, plate configuration, loading condition, and fracture gap localization) were classified into one of four groups: optimal bone union (OPT), probable union (PU), probable non-union (PNU), and non-union (NU).

CONCLUSIONS

No plating configuration is able to ensure distal humerus fracture union when the full elbow flexion is allowed while holding a weight of 1 kg in the hand. However, flexion in the range of 0-90° with such loadings is acceptable when using parallel plating, which is a positive finding in the context of the early rehabilitation process. In general, parallel plating ensures better conditions for fracture healing than perpendicular plate configurations, especially the posteromedial version.

IFM calculator: An algorithm for interfragmentary motion calculation in finite element analysis

BACKGROUND

Interfragmentary motion (IFM) is a complex state that significantly impacts the healing process of fractures following implant placement. It is crucial to fully consider the IFM state after implantation in the design and biomechanical testing of implants. However, current finite element analysis software lacks direct tools for calculating IFM, and existing IFM tools do not offer a comprehensive solution in terms of accuracy, functionality, and visualization.

METHODS

In our study, we developed a Python-based algorithm for calculating IFM that addresses limitations. Our algorithm automatically calculated IFM distances, sliding distances, gaps, as well as the angles and rotation of the two fracture surfaces using all nodes on both sides of the fracture ends. Researchers could input data and selected desired parameters in the interface. The algorithm then performed the necessary calculations and presented the results in a clear and concise manner. The algorithm also provided comprehensive data export capabilities, allowing researchers to customize analyses based on specific needs.To provide a more intuitive demonstration of the calculation process and usage of IFM-Cal, we conducted simulations in Ansys using two rectangular blocks to compare the accuracy and function of three different methods (Point based method, contact tool and IFM-Cal).

RESULTS

The point-based method and the contact tool could not accurately calculate IFA, while IFM-Cal could provide a comprehensive evaluation of IFA. In simulation 1, the IFM distances calculated using the point sampling method, contact tool, and IFM-Cal were 2.00 mm, 3.15 mm, and 2.00 mm, respectively. In simulation 2, both the point sampling method and contact tool failed to calculate the interfragmentary angle (IFA), while the IFM-Cal algorithm estimated an angle of -7.87°, which had a small error compared to the ground-truth value of 7.9°.

CONCLUSION

We have developed an algorithm for computing IFM which can be utilized in finite element analysis and biomechanical experiments. By conducting comparative simulations with other existing algorithms, we have demonstrated the superior accuracy and expanded evaluation capabilities of our algorithm.

Mechanical evaluation of revision surgery for femoral shaft nonunion initially treated with intramedullary nailing: Exchange nailing versus augmentation plating

INTRODUCTION

Exchange nailing (EN) or augmentation plating (AP) has been employed to treat nonunions after intramedullary nailing for femoral shaft fractures. Although instability is a factor in hypertrophic nonunion, mechanical evaluations have been limited because the contribution of the callus to fracture site stability varies with healing. Our previous study illustrated the potential for evaluation using a finite element analysis (FEA) that incorporates callus material properties. This study aimed to mechanically evaluate revision surgery for nonunions using FEA.

MATERIALS AND METHODS

A quantitative computed tomography-based FEA was performed on virtual revision models of a patient with suspected nonunion after intramedullary nailing. In addition to the initial nailing model (IN) with an 11-mm diameter (D) and 360-mm length (L), four EN models with D12mm (EN1), D13mm (EN2), D12mm-L400mm (EN3), and D13mm-L400mm (EN4) nails and three AP models with 5- (AP1), 6- (AP2), and 7-hole (AP3) plates were created. As with bone, callus was assigned inhomogeneous material properties derived from density based on an empirical formula. The hip joint reaction force and muscle forces at maximum load during the gait cycle were applied. The volume ratio of the callus at the fracture site with a tensile failure risk of ≥1 (tensile failure ratio) and bone fragment movement were evaluated.

RESULTS

The tensile failure ratio was 11.6 % (IN), 10.1 % (EN1), 6.3 % (EN2), 10.9 % (EN3), 6.2 % (EN4), 6.4 % (AP1), 7.2 % (AP2), and 7.7 % (AP3), respectively. The bone fragment movement showed an opening on the lateral side with the initial intramedullary nailing. However, both revision surgeries reduced the opening, leading to compression except in the EN1 model. The proximal bone fragments were internally rotated relative to the distal fragments, and the rotational instability was more suppressed in models with lower tensile failure ratio.

CONCLUSIONS

For EN, the increase in diameter, not length, is important to suppress instability. AP reduces instability, comparable to a 2 mm increase in nail diameter, and screw fixation closer to the fracture site reduces instability. This study suggest that AP is mechanically equivalent to EN and could be an option for revision surgery for femoral shaft nonunions.

In vivo characterization of 3D-printed polycaprolactone-hydroxyapatite scaffolds with Voronoi design to advance the concept of scaffold-guided bone regeneration

Three-dimensional (3D)-printed medical-grade polycaprolactone (mPCL) composite scaffolds have been the first to enable the concept of scaffold-guided bone regeneration (SGBR) from bench to bedside. However, advances in 3D printing technologies now promise next-generation scaffolds such as those with Voronoi tessellation. We hypothesized that the combination of a Voronoi design, applied for the first time to 3D-printed mPCL and ceramic fillers (here hydroxyapatite, HA), would allow slow degradation and high osteogenicity needed to regenerate bone tissue and enhance regenerative properties when mixed with xenograft material. We tested this hypothesis in vitro and in vivo using 3D-printed composite mPCL-HA scaffolds (wt 96%:4%) with the Voronoi design using an ISO 13485 certified additive manufacturing platform. The resulting scaffold porosity was 73% and minimal in vitro degradation (mass loss <1%) was observed over the period of 6 months. After loading the scaffolds with different types of fresh sheep xenograft and ectopic implantation in rats for 8 weeks, highly vascularized tissue without extensive fibrous encapsulation was found in all mPCL-HA Voronoi scaffolds and endochondral bone formation was observed, with no adverse host-tissue reactions. This study supports the use of mPCL-HA Voronoi scaffolds for further testing in future large preclinical animal studies prior to clinical trials to ultimately successfully advance the SGBR concept.

Impact of the adjacent bone on pseudarthrosis in mandibular reconstruction with fibula free flaps

BACKGROUND

Mechanical and morphological factors have both been described to influence the rate of pseudarthrosis in mandibular reconstruction. By minimizing mechanical confounders, the present study aims to evaluate the impact of bone origin at the intersegmental gap on osseous union.

METHODS

Patients were screened retrospectively for undergoing multi-segment fibula free flap reconstruction of the mandible including the anterior part of the mandible and osteosynthesis using patient-specific 3D-printed titanium reconstruction plates. Percentage changes in bone volume and width at the bone interface between the fibula/fibula and fibula/mandible at the anterior intersegmental gaps within the same patient were determined using cone-beam computed tomography (CBCT). Additionally, representative samples of the intersegmental zones were assessed histologically and using micro-computed tomography (µCT).

RESULTS

The bone interface (p = 0.223) did not significantly impact the change in bone volume at the intersegmental gap. Radiotherapy (p < 0.001), time between CBCT scans (p = 0.006) and wound healing disorders (p = 0.005) were independent risk factors for osseous non-union. Preliminary analysis of the microstructure of the intersegmental bone did not indicate morphological differences between fibula-fibula and fibula-mandible intersegmental bones.

CONCLUSIONS

The bone interface at the intersegmental gap in mandibular reconstruction did not influence long-term bone healing significantly. Mechanical and clinical properties seem to be more relevant for surgical success.

Fixators dynamization for delayed union and non-union of femur and tibial fractures: a review of techniques, timing and influence factors

The optimal balance between mechanical environment and biological factors is crucial for successful bone healing, as they synergistically affect bone development. Any imbalance between these factors can lead to impaired bone healing, resulting in delayed union or non-union. To address this bone healing disorder, clinicians have adopted a technique known as "dynamization" which involves modifying the stiffness properties of the fixator. This technique facilitates the establishment of a favorable mechanical and biological environment by changing a rigid fixator to a more flexible one that promotes bone healing. However, the dynamization of fixators is selective for certain types of non-union and can result in complications or failure to heal if applied to inappropriate non-unions. This review aims to summarize the indications for dynamization, as well as introduce a novel dynamic locking plate and various techniques for dynamization of fixators (intramedullary nails, steel plates, external fixators) in femur and tibial fractures. Additionally, Factors associated with the effectiveness of dynamization are explored in response to the variation in dynamization success rates seen in clinical studies.

Evaluation of bone healing process after intramedullary nailing for femoral shaft fracture by quantitative computed tomography-based finite element analysis

BACKGROUND

There is no proven method for quantitative evaluation of bone healing progress or decision to remove the nail after intramedullary nailing for femoral shaft fractures. Finite element analysis has become commonly utilized in bone analysis, but it may also be used to evaluate callus. The goal of this study was to use quantitative CT-based finite element analysis to assess the bone healing process and predict bone strength with the nail removed.

METHODS

Quantitative CT-based finite element analysis was conducted on CT images from patients who had intramedullary nailing after a femoral shaft fracture at 6, 12, and 15 months postoperatively. The failure risk of the callus was evaluated with maximal load throughout the gait cycle. The tensile failure ratio was calculated using the volume ratio of the callus element with a tensile failure risk ≥100%. A virtual model with the nail removed was built for bone strength study, and the strength was calculated using the displacement-load curve.

FINDINGS

The tensile failure ratio reduced with time, reaching 11.6%, 2.6%, and 0.5% at 6, 12, and 15 months postoperatively, respectively, consistent with bone healing inferred from imaging results. At 15 months, the bone strength at nail removal grew to 212, 2670, and 3385 N, surpassing the healthy side's 2766 N.

INTERPRETATION

Quantitative CT-based finite element analysis enables mechanical assessment during the bone healing process and is expected to be applied to the selection of revision surgery. It is also applicable to the nail removal decision.

A new design for the humerus fixation plate using a novel reliability-based topology optimization approach to mitigate the stress shielding effect

BACKGROUND

Due to high stiffness, metal fixation plates are prone to stress shielding of the peri-prosthetic bones, leading to bone loss. Therefore, it has become important to design implants with reduced rigidity but increased load-carrying capacity. Considering the uncertainties in the parameters affecting the implant-bone structure is critical in making more reliable implant designs. In this study, a Response Surface Method based Reliability-based Topology Optimization approach was proposed to design a fixation plate for humerus fracture having less stiffness than the conventional plate.

METHODS

The design of the fixation plate was described as an Reliability-based Topology Optimization problem in which the probabilistic constraint was replaced with a meta-model generated using the Kriging method. The artificial humerus bone model was scanned, and the 3D simulation model was used in the finite element analysis required in the solution. The optimum plate was manufactured using Selective Laser Melting. Both designs were experimentally compared in terms of rigidity.

FINDINGS

The volume of the conventional plate was reduced from 2512.5 mm³ to 1667.3 mm³; nevertheless, the optimum plate had almost one-third less rigidity than the conventional plate. The probability of failure of the conventional plate was computed as 0.994. However, this value was almost half for the optimum fixation plate. Interpretation The studies showed that the new fixation plate design was less rigid but more reliable than the conventional one. The computation time required to have the optimum plate was reduced by one-tenth by applying the Response Surface Method for the Reliability-based Topology Optimization problem.

Mechanical Characterization at the Microscale of Mineralized Bone Callus after Bone Lengthening

Distraction osteogenesis (DO) involves several processes to form an organized distracted callus. While bone regeneration during DO has been widely described, no study has yet focused on the evolution profile of mechanical properties of mineralized tissues in the distracted callus. The aim of this study was therefore to measure the elastic modulus and hardness of calcified cartilage and trabecular and cortical bone within the distracted callus during the consolidation phase. We used a microindentation assay to measure the mechanical properties of periosteal and endosteal calluses; each was subdivided into two regions. Histological sections were used to localize the tissues. The results revealed that the mechanical properties of calcified cartilage did not evolve over time. However, trabecular bone showed temporal variation. For elastic modulus, in three out of four regions, a similar evolution profile was observed with an increase and decrease over time. Concerning hardness, this evolves differently depending on the location in the distracted callus. We also observed spatial changes in between regions. A first duality was apparent between regions close to the native cortices and the central area, while latter differences were seen between periosteal and endosteal calluses. Data showed a heterogeneity of mechanical properties in the distracted callus with a specific mineralization profile.

Increased rate of pseudarthrosis in the anterior intersegmental gap after mandibular reconstruction with fibula free flaps: a volumetric analysis

OBJECTIVES

Pseudarthrosis after mandibular reconstruction leads to chronic overload of the osteosynthesis and impedes dental rehabilitation. This study evaluates the impact of gap site on osseous union in mandible reconstruction using a new volumetric analysis method with repeated cone-beam computed tomography (CBCT).

METHODS

The degree of bone regeneration was evaluated in 16 patients after mandible reconstruction with a fibula free flap and patient-specific reconstruction plates. Percentual bone volume and width changes in intersegmental gaps were retrospectively analyzed using a baseline CBCT in comparison to a follow-up CBCT. Patients' characteristics, plate-related complications, and gap sites (anterior/posterior) were analyzed. Detailed assessments of both gap sites (buccal/lingual/superior/inferior) were additionally performed.

RESULTS

Intersegmental gap width (p = 0.002) and site (p < 0.001) significantly influence bone volume change over two consecutive CBCTs. An initial larger gap width resulted in a lower bone volume change. In addition, anterior gaps showed significantly less bone volume changes. Initial gap width was larger at posterior segmental gaps (2.97 vs 1.65 mm, p = 0.017).

CONCLUSIONS

A methodology framework has been developed that allows to quantify pseuarthrosis in reconstructed mandibles using CBCT imaging. The study identifies the anterior segmental gap as a further risk factor for pseudarthrosis in reconstructions with CAD/CAM reconstruction plates. Future research should evaluate whether this outcome is related to the biomechanics induced at this site.

Finite element analysis between Hunsuck/Epker and novel modification of Low Z plasty technique of mandibular sagittal split osteotomy

A novel modification of the Low Z plasty (NM-Low Z) technique for bilateral sagittal split osteotomy was recently proposed. The osteotomy line was modified more inferiorly than in the conventional Hunsuck–Epker (HE) approach. The NM-Low Z technique enhances the mandibular setback distance and degree of rotation in severe skeletal discrepancies. This study aimed to investigate the biomechanical behavior under simulated forces, and to compare the NM-Low Z and HE techniques on the mandible with Class III skeletal deformity at 1 week, 3 weeks, and 6 weeks post-operation. Physiological muscular and occlusal loads were simulated using the finite element (FE) method. Stresses on the miniplate, screws, and bone were observed and compared between the two models. The elastic strain at the fracture site was observed for the optimal bone-healing capacity. The NM-Low Z model exhibited a lower stress than the HE model at every stage post-operation. Both models demonstrated elastic strains within the normal range for bone healing. In summary, the biomechanical behavior of the NM-Low Z technique is comparable to that of the conventional EH technique. NM-Low Z could facilitate post-operation skeletal stability by reducing the stress on fixation materials during bone healing.

Mechanical Stimulation on Mesenchymal Stem Cells and Surrounding Microenvironments in Bone Regeneration: Regulations and Applications

Treatment of bone defects remains a challenge in the clinic. Artificial bone grafts are the most promising alternative to autologous bone grafting. However, one of the limiting factors of artificial bone grafts is the limited means of regulating stem cell differentiation during bone regeneration. As a weight-bearing organ, bone is in a continuous mechanical environment. External mechanical force, a type of biophysical stimulation, plays an essential role in bone regeneration. It is generally accepted that osteocytes are mechanosensitive cells in bone. However, recent studies have shown that mesenchymal stem cells (MSCs) can also respond to mechanical signals. This article reviews the mechanotransduction mechanisms of MSCs, the regulation of mechanical stimulation on microenvironments surrounding MSCs by modulating the immune response, angiogenesis and osteogenesis, and the application of mechanical stimulation of MSCs in bone regeneration. The review provides a deep and extensive understanding of mechanical stimulation mechanisms, and prospects feasible designs of biomaterials for bone regeneration and the potential clinical applications of mechanical stimulation.

International recognition of the Ilizarov bone reconstruction techniques: Current practice and research (dedicated to 100th birthday of G. A. Ilizarov)

The Ilizarov method is one of the current methods used in bone reconstruction. It originated in the middle of the past century and comprises a number of bone reconstruction techniques executed with a ring external fixator developed by Ilizarov GA. Its main merits are viable new bone formation through distraction osteogenesis, high union rates and functional use of the limb throughout the course of treatment. The study of the phenomenon of distraction osteogenesis induced by tension stress with the Ilizarov apparatus was the impetus for advancement in bone reconstruction surgery. Since then, the original method has been used along with a number of its modifications developed due to emergence of new fixation devices and techniques of their application such as hexapod external fixators and motorized intramedullary lengthening nails. They gave rise to a relatively new orthopedic subspecialty termed “limb lengthening and reconstruction surgery”. Based on a comprehensive literature search, we summarized the recent clinical practice and research in bone reconstruction by the Ilizarov method with a special focus on its modification and recognition by the world orthopedic community. The international influence of the Ilizarov method was reviewed in regard to the origin country of the authors and journal’s rating. The Ilizarov method and other techniques based on distraction osteogenesis have been used in many countries and on all populated continents. It proves its international significance and confirms the greatest contribution of Ilizarov GA to bone reconstruction surgery.

Biomechanical comparison of different cerclage types in addition to an angle stable plate osteosynthesis of distal tibial fractures

BACKGROUND

Different stand-alone cerclage configurations and their optimal twisting techniques have been investigated over the years. This study tests for the stabilizing effect of different supplemental cerclage materials in combination with locked plating of distal tibia fractures.

METHODS

Locking plate fixation of a distal tibial spiral fracture was tested as stand-alone and with supplemental cerclage materials (one cable, two cables, wire, fiber tape). Construct stiffness and fracture gap movements were investigated under quasi-static and dynamic loads and compared to the stand-alone locking plate.

RESULTS

With each of the tested cerclages, stiffness was significantly higher than for a solitary plate osteosynthesis. Most reduction in fracture gap movement was achieved by cable cerclages, followed by double-looped wire and double-looped fiber tape cerclages. Under dynamic loading an additional cable cerclage reduces excessive gap movement.

CONCLUSION

Compared to solitary plate osteosynthesis all supplemental cerclage materials were generally superior with reduced fracture gap movements whereas cable cerclages showing the greatest stabilizing effect.

Optimal time-dependent levels of weight-bearing for bone fracture healing under Ilizarov circular fixators

It is known that weight-bearing exercises under Ilizarov circular fixators (ICF) could enhance bone fracture healing by mechano-regulation. However, interfragmentary movements at the fracture site induced by weight-bearing may inhibit angiogenesis and ultimately delay the healing process. To tackle this challenge, a computational model is presented in this study which considers the spatial and temporal changes in mechanical properties of fracture callus to predict optimal levels of weight-bearing during fracture healing under ICF. The study takes sheep fractures as example and shows that the developed model has the capability of predicting patient specific, time-dependent optimal levels of weight-bearing which enhances mechano-regulation mediated healing without hindering the angiogenesis process. The results demonstrate that allowable level of weight-bearing and timings depend on fracture gap size. For normal body weights (BW) and moderate fracture gap sizes (e.g. 3 mm), weight-bearing with 30% BW could start by week 4 post-operation and gradually increase to 100% BW by week 11. In contrast, for relatively large fracture gap sizes (i.e. 6 mm), weight-bearing is recommended to commence in later stages of healing (e.g. week 11 post-operation). Furthermore, increasing ICF stiffness (e.g. using half pins instead of pretension wires) can increase the level of weight-bearing significantly in the early stages up to a certain time point (e.g. week 8 post-operation) beyond which no noticeable benefits could be achieved. The findings of this study have potential applications in designing post-operative weight bearing exercises.

Supplemental cerclage wiring in angle stable plate fixation of distal tibial spiral fractures enables immediate post-operative full weight-bearing: a biomechanical analysis

Purpose

Distal tibial fractures generally require post-operative weight-bearing restrictions. Especially geriatric patients are unable to follow these recommendations. To increase post-operative implant stability and enable early weight-bearing, augmentation of the primary osteosynthesis by cerclage is desirable. The purpose of this study was to identify the stabilizing effects of a supplemental cable cerclage following plate fixation of distal tibial spiral fractures compared to solitary plate osteosynthesis.

Methods

In eight synthetic tibiae, a reproducible spiral fracture (AO/OTA 42-A1.1c) was stabilized by angle stable plate fixation. Each specimen was statically loaded under combined axial and torsional loads to simulate partial (200 N, 2 Nm) and full (750 N, 7 Nm) weight-bearing. Tests were repeated with supplemental cable cerclage looped around the fracture zone. In a subsequent stepwise increased dynamic load scenario, construct stiffness and interfragmentary movements were analyzed.

Results

With supplemental cable cerclage, construct stiffness almost tripled compared to solitary plate osteosynthesis (2882 ± 739 N/mm vs. 983 ± 355 N/mm; p < 0.001). Under full weight-bearing static loads, a supplemental cerclage revealed reduced axial (− 55%; p = 0.001) and shear movement (− 83%; p < 0.001), and also lowered shear movement (− 42%; p = 0.001) compared to a solitary plate under partial weight-bearing. Under dynamic loads supplemental cerclage significantly reduced axial (p = 0.005) as well as shear movements (p < 0.001).

Conclusion

Supplemental cable cerclage significantly increases fixation stiffness and reduces shear movement in distal tibial spiral fractures. This stabilizing effect enables from a biomechanical point of view immediate mobilization without any weight-bearing restrictions, which may improve the quality of care of orthopedic patients and may trigger a change towards early weight-bearing regimes, especially geriatric patients would benefit from.

Extracellular matrix compression temporally regulates microvascular angiogenesis

Mechanical cues influence tissue regeneration, and although vasculature is known to be mechanically sensitive, little is known about the effects of bulk extracellular matrix deformation on the nascent vessel networks found in healing tissues. Previously, we found that dynamic matrix compression in vivo potently regulated revascularization during bone tissue regeneration; however, whether matrix deformations directly regulate angiogenesis remained unknown. Here, we demonstrated that load initiation time, magnitude, and mode all regulate microvascular growth, as well as upstream angiogenic and mechanotransduction signaling pathways. Immediate load initiation inhibited angiogenesis and expression of early sprout tip cell selection genes, while delayed loading enhanced microvascular network formation and upstream signaling pathways. This research provides foundational understanding of how extracellular matrix mechanics regulate angiogenesis and has critical implications for clinical translation of new regenerative medicine therapies and physical rehabilitation strategies designed to enhance revascularization during tissue regeneration.

Stability evaluation of anterior external fixation in patient with unstable pelvic ring fracture: a finite element analysis

Background

The pelvic ring fractures (PRF) are commonly induced by the high-energy impact and will lead to unstable and sever injures. This study is aimed to explore the stability of anterior external fixation in treating pelvis fracture and evaluate the possibility for these kinds of patients to reduce bedridden time.

Methods

A patient with Tile B3 pelvis fracture was chosen in the research and the corresponding digital model was reconstructed according to the CT images and 3D scanning. Four angles of pelvis under vertical compression were employed in the finite element (FE) analyses. The stress distribution and micro-motion displacement were calculated to validate the instability of pelvis.

Results

The stress applied on the pelvis was ranged from 4.296 to 8.364 MPa in all postures. The stress applied on pins was less than 7.011 MPa during reclining, and reached 28.29 MPa when standing. The micro-motion displacement in reclining posture was ranged from 0.005 to 0.087 mm. The value increased to more than 1mm in standing posture.

Conclusions

It was safety for patients with pelvis fracture to sit vertical or recline on the bed during nursing or having treatment, but standing or walking will generate inappropriate micro-motion. The existence of external fixation can reduce the possibility of complications caused by long-term bedridden.