Prediction of three-dimensional contact stress and ligament tension in the ankle during stance determined from computational modeling

Comparison of the use of biocompatible materials and titanium in the treatment of midshaft clavicle fractures with a patient-specific plate: a finite element analysis study

BACKGROUND

Clavicular midshaft fractures treated with titanium plates may encounter complications like implant failure. We assess if alternative biocompatible materials suchs as PLA, PLA/HA, PEEK offer comparable stability. Our study evaluates the biomechanical performance of these materials in surgical management of midshaft clavicle fractures.

METHODS

We simulated a personalized fixation implant with four different materials and conducted finite element analysis in ANSYS to assess maximum von Mises stress (MvMs).

RESULTS

The MvMs occurring on the plates, screws, clavicle, and fracture site were recorded. MvMs on titanium material at the 6th hole level (764.79 MPa) and the 6th screw level (503.38 MPa), with the highest stresses observed at 48.52 MPa on the lateral clavicle at the 1st hole level and 182.27 MPa on the medial clavicle at the 6th hole level. In PLA material analyses, the highest MvMs were observed at the 3rd hole level (340.6 MPa) and the 3rd screw level (157.83 MPa), with peak stresses at 379.63 MPa on the lateral clavicle fracture line and 505.44 MPa on the medial clavicle fracture line. In PLA/HA material analyses, the highest MvMs were at the 3rd hole (295.99 MPa) and 3rd screw (128.27 MPa), with peak stresses at 220.33 MPa on the lateral clavicle and 229.63 MPa on the medial clavicle fracture line. In PEEK material analyses, the highest MvMs were at the 3rd hole (234.74 MPa) and 6th screw (114.48 MPa), with peak stresses at 184.36 MPa on the lateral clavicle and 180.1 MPa on the medial clavicle.

CONCLUSION

Our findings indicate that titanium material shows significantly higher stresses on plates and screws compared to those on the clavicle, suggesting a risk of implant failure. PLA and PLA/HA were inadequate for fixation. Although stress on the plate with PEEK material is higher than on the clavicle, it remains lower than titanium, indicating potential stability at fracture site. Further research is needed to confirm these findings.

Stabilizing effect of total ankle arthroplasty by distal translation and lateralization of talus in varus ankle deformity

BACKGROUND

In end-stage arthritis indicated for total ankle arthroplasty (TAA), full-thickness cartilage damage, subchondral bone defect/shaving, and fluttering of the talar dome occur, shortening the distance between the tibial and talar insertions of ligaments and leading to laxity of ligaments surrounding the ankle joint. Under such conditions, medial ligaments (including the deltoid ligament) would not be expected to function properly. To stabilize the ankle joint during the stance phase, medial ligament function under tension is important. This study therefore examined whether TAA contributes to lengthening of the medial tibio-talar joint as evaluated radiographically, as a preferable method for achieving tensile effects on medial ligaments.

MATERIALS AND METHODS

Twenty-four feet with end-stage varus deformity of the ankle joint that underwent TAA were retrospectively investigated, excluding cases with any malleolar osteotomy or fracture. Distance between proximal and distal insertions of medial ligaments, lateralization of the talus, and talar tilt angle under valgus/varus stress condition were evaluated pre- and postoperatively.

RESULTS

Distance between proximal and distal insertions of medial ligaments was significantly elongated after TAA. At the same time, the talus showed significant lateralization. Furthermore, talar tilt under valgus/varus stress conditions was also significantly reduced after TAA.

CONCLUSION

TAA affects distal translation and lateralization of the talus in cases of varus ankle deformity. These effects might contribute to re-providing tensile force on lax medial ligaments, improving ligament function.

Anthropomorphic Characterization of Ankle Joint

Even though total ankle replacement has emerged as an alternative treatment to arthrodesis, the long-term clinical results are unsatisfactory. Proper design of the ankle device is required to achieve successful arthroplasty results. Therefore, a quantitative knowledge of the ankle joint is necessary. In this pilot study, imaging data of 22 subjects (with both females and males and across three age groups) was used to measure the morphological parameters of the ankle joint. A total of 40 measurements were collected by creating sections in the sagittal and coronal planes for the tibia and talus. Statistical analyses were performed to compare genders, age groups, and image acquisition techniques used to generate 3D models. About 13 measurements derived for parameters (TiAL, SRTi, TaAL, SRTa, TiW, TaW, and TTL) that are very critical for the implant design showed significant differences (p-value < 0.05) between males and females. Young adults showed a significant difference (p-value < 0.05) compared to adults for 15 measurements related to critical tibial and talus parameters (TiAL, TiW, TML, TaAL, SRTa, TaW, and TTL), but no significant differences were observed between young adults and older adults, and between adults and older adults for most of the parameters. A positive correlation (r > 0.70) was observed between tibial and talar width values and between the sagittal radius values. When compared with morphological parameters obtained in this study, the sizes of current total ankle replacement devices can only fit a very limited group of people in this study. This pilot study contributes to the comprehensive understanding of the effects of gender and age group on ankle joint morphology and the relationship between tibial and talus parameters that can be used to plan and design ankle devices.

Do lateral ankle ligaments contribute to syndesmotic stability: a finite element analysis study

Whether the lateral ankle ligaments contribute to syndesmotic stability is still controversial and has been the subject of frequent research recently. In our study, we tried to elucidate this situation using the finite element analysis method. Intact model and thirteen different injury models were created to simulate injuries of the lateral ankle ligaments (ATFL, CFL, PTFL), injuries of the syndesmotic ligaments (AITFL, IOL, PITFL) and their combined injuries. The models were compared in terms of LFT, PFT and EFR. It was observed that 0.537 mm LFT, 0.626 mm PFT and 1.25° EFR occurred in the intact model (M#1), 0.539 mm LFT, 0.761 mm PFT and 2.31° EFR occurred in the isolated ATFL injury (M#2), 0.547 mm LFT, 0.791 mm PFT and 2.50° EFR occurred in the isolated AITFL injury (M#8). The LFT, PFT and EFR amounts were higher in the both M#2 and M#8 compared to the M#1. LFT, PFT and EFR amounts in M#2 and M#8 were found to be extremely close. In terms of LFT and PFT, when we compare models with (LFT: 0.650 mm, PFT: 1.104) and without (LFT: 0.457 mm, PFT: 1.150) IOL injury, it is seen that the amount of LFT increases and the amount of PFT decreases with IOL injury. We also observed that injuries to the CFL, PTFL and PITFL did not cause significant changes in fibular translations and PFT and EFR values show an almost linear correlation. Our results suggest that ATFL injury plays a crucial role in syndesmotic stability.

Radiographic foot alignment and morphological features of deltoid ligament in pediatric patients with medial osteochondral lesions of the talus

The cause of osteochondral lesions of the talus (OLT) in patients without a history of trauma remains unclear, and almost all nontraumatic lesions appear to involve the medial talar dome. This study aimed to investigate the relationship between foot alignment, deltoid morphology, and medial OLT in pediatric patients. In total, 28 patients (31 feet) with medial OLT (17 boys, 11 girls, mean age: 14.9 years), and 50 patients without OLT (50 feet, 31 boys, 19 girls, mean age: 14.5 years) were included in this study. The OLT patients were subdivided into traumatic and nontraumatic groups. Radiographic parameters of the foot arch were measured on weight-bearing lateral images. The extent of the OLT was measured on computed tomographic images. The ratio of deep deltoid attachment length of the talus to talar height was examined as deltoid ligament position index (DPI) on coronal magnetic resonance imaging. Nontraumatic medial lesions were frequently observed in pediatric patients (54.8%) compared to traumatic lesions. The depression of the foot arch was commonly identified in pediatric patients with resistant medial lesions. The lesion size was moderately correlated with DPI (rho = 0.48; P = 0.0086). The attachment of the deep deltoid ligament to the medial talar dome was located more proximally in nontraumatic lesions than in traumatic lesions and the control group. Our findings suggest that a combination of foot alignment and the anatomic variations in the attachment of the deep deltoid ligament contributes to the incidence of nontraumatic medial OLT in the pediatric population. Level of evidence: level IV.

Biomechanical Analysis of Tibiofibular Syndesmosis Injury Fixation Methods: A Finite Element Analysis

The optimal treatment strategy after syndesmotic injuries is still controversial. In our study, we aimed to evaluate ideal fixation method in syndesmotic injury by using finite element analysis method. A 3D SolidWorks model file was created by taking computed tomography (CT) images of the area from the right foot base to the knee joint level of a healthy adult male. The intact model, injury model, and 8 different fixation models were created that 3.5 mm screw and suture-button were used in. The models were compared in terms of lateral fibular translation, posterior fibular translation and external rotation of fibula compared to tibia and stress values occurred on screws and suture-buttons. In the hybrid-1 model, lateral fibular translation and external fibular rotation values were obtained as close to the intact model. Von Mises stresses occurred in the screw (435.7 MPa) and suture-button (424.7 MPa) that used in hybrid-1 model was more than single screw at 4 cm model (316.8 MPa) and single suture-button at 2 cm model (160.7 MPa). In the Hybrid-1 model, the screw compensates for posterior fibular translation and external fibular rotation, while the suture-button compensates for lateral fibular translation. Also, the effect of the distal suture-button preventing diastasis in case of proximal screw failure, it was concluded that the hybrid-1 model can be used as a good treatment alternative in the surgical treatment of distal tibiofibular syndesmotic injuries.

Effect of Accelerated Rehabilitation on Early Return to Sport After Arthroscopic Ankle Lateral Ligament Repair

Background

Although the minimal invasiveness of arthroscopic ankle lateral ligament repair (ALLR) means that an early return to sporting activities can be anticipated, studies have described postoperative cast immobilization and the avoidance of weightbearing for a certain period. Accelerated rehabilitation may be helpful for an early return to sport.

Purpose

To investigate clinical outcomes of ALLR and accelerated rehabilitation with a minimum duration of postoperative ankle immobilization and proactive early weightbearing.

Study Design

Case series; Level of evidence, 4.

Methods

This study investigated 23 ankles of 22 patients (11 men, 11 women; mean age, 38.7 years) who underwent ALLR for chronic lateral ankle instability. Postoperative management included the avoidance of weightbearing until postoperative day 3, after which full weightbearing walking with a brace was permitted. The objective was to return to competitive sport 8 weeks after surgery. The following were evaluated: pre- and postoperative instability and pain symptoms, ankle range of motion, anterior drawer distance on stress radiograph, anterior translation measured with a capacitance-type strain sensor, the Ankle-Hindfoot Scale from the Japanese Society for Surgery of the Foot, and the SAFE-Q (Self-Administered Foot Evaluation Questionnaire).

Results

Two male patients dropped out and were excluded from analysis. Postoperatively, instability and pain resolved or improved in all patients. There was no significant postoperative change in range of motion. There were significant pre- to postoperative improvements in talar tilt angle (from 12.2°-5.6°, P < .01), anterior drawer distance (8.2-4.4 mm, P < .01), and anterior translation (10.5-4.6 mm, P < .01) as well as the Ankle-Hindfoot Scale score (68.8-96.8, P < .01) and all subscales of the SAFE-Q (P ≤ .01 for all). Complete return to sport was achieved by 75% of the patients at 8 weeks postoperatively.

Conclusion

When accelerated rehabilitation with proactive weightbearing exercises was implemented from postoperative day 3 without ankle immobilization after ALLR, there were significant improvements in objective assessments of ankle stability and clinical scores, and as many as 75% of the patients were able to make a complete return to sport within 8 weeks.

Suture button fixation method used in the treatment of syndesmosis injury: A biomechanical analysis of the effect of the placement of the button on the distal tibiofibular joint in the mid-stance phase with finite elements method

PURPOSE

The purpose of this study is to research the effect of suture button (SB) fixation, a method used at the treatment of ankle syndesmosis injury, which was applied in various angles, pretension force, and levels, on the distal tibiofibular joint (DTFJ) in the mid-stance phase, with the help of three-dimensional finite elements method (FEM) METHOD: The ankle of a healthy individual was digitally analyzed by a finite element method-based package computer program. Then, anterior inferior tibiofibular ligament (AITFL), interosseous ligament, posterior inferior tibiofibular ligament (PITFL) and deltoid ligament (DL) were cut and force and rotation has been applied to the proximal tibia, resulting in syndesmosis injury. Then, various suture button applications on the injured model have been analyzed. Three parameters have been changed; which were divergence in the axial plane (20°, 30°, 40°), distance from the ankle (2, 3, 4 cm), and pretension force (200, 300, 600 N) RESULTS: As the result of this study, the rotation, change in the gap between the distal tibia and distal fibula, and the displacements of the fibula in the x and y axes have been obtained, and numerical results were evaluated. As the force increased, rotation, change in the gap between the distal tibia and distal fibula, and the displacements of the fibula decreased. As suture button application rotation increased, change in the gap between the distal tibia and distal fibula, and displacements of the fibula increased. As the distance from the ankle increases and reaches a certain level, the results converge to those of the healthy model; in the proximal, it diverges from healthy results.

CONCLUSION

In the study, it has been shown that abnormal tibiofibular joint movements can be prevented with suture button application, and optimum application parameters (divergence in the axial plane, distance from the ankle, and pretension force) are given for proper reduction.

Effect of Ligament Mapping from Different Magnetic Resonance Image Quality on Joint Stability in a Personalized Dynamic Model of the Human Ankle Complex

Background. Mechanical models of the human ankle complex are used to study the stabilizing role of ligaments. Identification of ligament function may be improved via image-based personalized approach. The aim of this study is to compare the effect of the ligament origin and insertion site definitions obtained with different magnetic resonance imaging (MRI) modalities on the mechanical behaviour of a dynamic model of the ankle complex. Methods. MRI scans, both via 1.5 T and 3.0 T, were performed on a lower-limb specimen, free from anatomical defects, to obtain morphological information on ligament-to-bone attachment sites. This specimen was used previously to develop the dynamic model. A third ligament attachment site mapping scheme was based on anatomical dissection of the scanned specimen. Following morphological comparison of the ligament attachment sites, their effect on the mechanical behaviour of the ankle complex, expressed by three-dimensional load–displacement properties, was assessed through the model. Results. Large differences were observed in the subtalar ligament attachment sites between those obtained through the two MRI scanning modalities. The 3.0 T MRI mapping was more consistent with dissection than the 1.5 T MRI. Load–displacement curves showed similar mechanical behaviours between the three mappings in the frontal plane, but those obtained from the 3.0 T MRI mapping were closer to those obtained from dissection. Conclusions. The state-of-the-art 3.0 T MRI image analysis resulted in more realistic mapping of ligament fibre origin and insertion site definitions; corresponding load–displacement predictions from a subject-specific model of the ankle complex showed a mechanical behaviour more similar to that using direct ligament attachment observations.

In Vivo Syndesmotic Motion After Rigid and Flexible Fixation Using 4-Dimensional Computerized Tomography

INTRODUCTION

Maintaining reduction after syndesmotic injury is crucial to patient function; however, malreduction remains common. Flexible suture button fixation may allow more physiologic motion of the syndesmosis compared with rigid screw fixation. Conventional syndesmotic imaging fails to account for physiologic syndesmotic motion with ankle range of motion (ROM), providing misleading results. Four-dimensional computerized tomography (4DCT) can image joints through a dynamic ROM. Our purpose was to compare syndesmotic motion after rigid and flexible fixation using 4DCT.

METHODS

We analyzed 13 patients with syndesmotic injury who were randomized to receive rigid (n = 7) or flexible (n = 6) fixation. Patients underwent bilateral ankle 4DCT while moving between ankle dorsiflexion and plantar flexion. Measures of syndesmotic position and rotation were extracted from 4DCT to determine syndesmotic motion as a function of ankle ROM.

RESULTS

Uninjured ankles demonstrated significant decreases in syndesmotic width of 1.0 mm with ankle plantar flexion (SD = 0.6 mm, P < 0.01). Initial rigid fixation demonstrated reduced motion compared with uninjured ankles in 4 of 5 measures (P < 0.01) despite all patients in the rigid fixation group having removed, loose, or broken screws by the time of imaging. Rigid fixation led to less motion than flexible fixation in 3 measures (P = 0.02-0.04). There were no observed differences in syndesmotic position or motion between flexible fixation and uninjured ankles.

CONCLUSION

Despite the loss of fixation in all subjects in the rigid fixation group, initial rigid fixation led to significantly reduced syndesmotic motion. Flexible fixation recreated more physiologic motion compared with rigid fixation and may be used to reduce rates of syndesmotic malreduction.

LEVEL OF EVIDENCE

Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.

Personalised statistical modelling of soft tissue structures in the ankle

BACKGROUND AND OBJECTIVE

Revealing the complexity behind subject-specific ankle joint mechanics requires simultaneous analysis of three-dimensional bony and soft-tissue structures. 3D musculoskeletal models have become pivotal in orthopedic treatment planning and biomechanical research. Since manual segmentation of these models is time-consuming and subject to manual errors, (semi-) automatic methods could improve the accuracy and enlarge the sample size of personalised 'in silico' biomechanical experiments and computer-assisted treatment planning. Therefore, our aim was to automatically predict ligament paths, cartilage topography and thickness in the ankle joint based on statistical shape modelling.

METHODS

A personalised cartilage and ligamentous prediction algorithm was established using geometric morphometrics, based on an 'in-house' generated lower limb skeletal model (N = 542), tibiotalar cartilage (N = 60) and ankle ligament segmentations (N = 10). For cartilage, a population-averaged thickness map was determined by use of partial least-squares regression. Ligaments were wrapped around bony contours based on iterative shortest path calculation. Accuracy of ligament path and cartilage thickness prediction was quantified using leave-one-out experiments. The novel personalised thickness prediction was compared with a constant cartilage thickness of 1.50 mm by use of a paired sample T-test.

RESULTS

Mean distance error of cartilage and ligament prediction was 0.12 mm (SD 0.04 mm) and 0.54 mm (SD 0.05 mm), respectively. No significant differences were found between the personalised thickness cartilage and segmented cartilage of the tibia (p = 0.73, CI [-1.60 .10^-17, 1.13 .10^-17]) and talus (p = 0.95, CI[ -1.35 .10^-17, 1.28 .10^-17]). For the constant thickness cartilage, a statistically significant difference was found in 89% and 92% of the tibial (p < 0.001, CI [0.51, 0.58]) and talar (p < 0.001, CI [0.33, 0.40]) cartilage area.

CONCLUSIONS

In this study, we described a personalised prediction algorithm of cartilage and ligaments in the ankle joint. We were able to predict cartilage and main ankle ligaments with submillimeter accuracy. The proposed method has a high potential for generating large (virtual) sample sizes in biomechanical research and mitigates technological advances in computer-assisted orthopaedic surgery.

Predicting ankle joint syndesmotic screw lifetime using finite element and fatigue analysis

After recovery and loading on the patient’s leg, syndesmotic screws mounted on an injured ankle may fail. The main subject of this study is to estimate the lifetime of screws considering the patient’s weight and physical activity. Method: A 3D finite element model of the bone and implemented screws were provided assigning the mechanical properties of ligaments, bones, and screws. Considering axial and tangential physiological loads during the walking phase, the stress and fatigue analyses were performed. Results: The stress distribution had an identical pattern in the screws and all of them experienced the maximum stress during 60–70% of the walking phase. Conclusion: The results of analyses show that body weight has a significant effect on the mounted screw lifetime. Patients with a weight of more than [Formula: see text] kg should prevent applying body load on the operated leg. Conversely, no worry about a patient having less than [Formula: see text] kg body weight.

Three-Dimensional Subject-Specific Knee Shape Reconstruction with Asynchronous Fluoroscopy Images Using Statistical Shape Modeling

Background and objectives: Statistical shape modeling (SSM) based on computerized tomography (CT) datasets has enabled reasonably accurate reconstructions of subject-specific 3D bone morphology from one or two synchronous radiographs for clinical applications. Increasing the number of radiographic images may increase the reconstruction accuracy, but errors related to the temporal and spatial asynchronization of clinical alternating bi-plane fluoroscopy may also increase. The current study aimed to develop a new approach for subject-specific 3D knee shape reconstruction from multiple asynchronous fluoroscopy images from 2, 4, and 6 X-ray detector views using a CT-based SSM model; and to determine the optimum number of planar images for best accuracy via computer simulations and in vivo experiments.

Methods: A CT-based SSM model of the knee was established from 60 training models in a healthy young Chinese male population. A new two-phase optimization approach for 3D subject-specific model reconstruction from multiple asynchronous clinical fluoroscopy images using the SSM was developed, and its performance was evaluated via computer simulation and in vivo experiments using one, two and three image pairs from an alternating bi-plane fluoroscope.

Results: The computer simulation showed that subject-specific 3D shape reconstruction using three image pairs had the best accuracy with RMSE of 0.52 ± 0.09 and 0.63 ± 0.085 mm for the femur and tibia, respectively. The corresponding values for the in vivo study were 0.64 ± 0.084 and 0.69 ± 0.069 mm, respectively, which was significantly better than those using one image pair (0.81 ± 0.126 and 0.83 ± 0.108 mm). No significant differences existed between using two and three image pairs.

Conclusion: A new two-phase optimization approach was developed for SSM-based 3D subject-specific knee model reconstructions using more than one asynchronous fluoroscopy image pair from widely available alternating bi-plane fluoroscopy systems in clinical settings. A CT-based SSM model of the knee was also developed for a healthy young Chinese male population. The new approach was found to have high mode reconstruction accuracy, and those for both two and three image pairs were much better than for a single image pair. Thus, two image pairs may be used when considering computational costs and radiation dosage. The new approach will be useful for generating patient-specific knee models for clinical applications using multiple asynchronous images from alternating bi-plane fluoroscopy widely available in clinical settings. The current SSM model will serve as a basis for further inclusion of training models with a wider range of sizes and morphological features for broader applications.

Medial Ankle Stability Evaluation With Dynamic Ultrasound: Establishing Natural Variations in the Healthy Cohort

INTRODUCTION

Destabilizing injuries to the deltoid ligament have relied on radiographic stress examination for diagnosis, with a focus on medial clear space (MCS) widening. Recently, studies have demonstrated the use of ultrasonography to assess deltoid ligament injury, but not the medial ankle stability. The purpose of this study was to assess the MCS via ultrasonography while weight-bearing and with a gravity stress test (GST) in the uninjured ankle as a means of establishing normative values for future comparison.

METHODS

Twenty-six participants with no reported ankle injury in their premedical history were included. The MCS was examined using ultrasonography with the patient lying in a lateral decubitus position to replicate a GST with the ankle held in a neutral and plantarflexed position as well as while weight-bearing. The MCS was assessed in mm at the anteromedial and inferomedial aspect of the ankle joint.

RESULTS

With weight-bearing, the average anterior MCS and inferior MCS were 3.6 and 3.3 mm, respectively. During the GST in neutral ankle position, the average anterior MCS was 4.1 mm, whereas the average inferior MCS was 4.0 mm. When measured during the GST in plantarflexed ankle position, the averages anterior MCS and inferior MCS increased to 4.4 mm. MCS values were notably higher with GST than with weight-bearing measurements (P < 0.001). MCS values were notably higher with the foot in a plantarflexed compared with a neutral position when doing GST (P < 0.001). No notable differences in MCS distance were found when comparing laterality (P > 0.05). Height had a notable effect on all MCS values (P < 0.05). Inter- and intra-rater reliabilities for ultrasonographic MCS measurements were all excellent (interclass correlation coefficient >0.75).

DISCUSSION

Ultrasound can reliably measure the MCS of the ankle while doing dynamic stress manoeuvres. With the deltoid ligament intact, a GST increases MCS widening more than weight-bearing, and holding the ankle in plantarflexion while doing a gravity stress view, further increases this difference.

LEVELS OF EVIDENCE

Diagnostic studies-investigating a diagnostic test: Level III.

Arthroscopic ankle lateral ligament repair alone versus arthroscopic ankle lateral ligament repair with reinforcement by inferior extensor retinaculum

PURPOSE

This study aimed to compare the clinical outcomes and postoperative activities of arthroscopic ankle lateral ligament (ALL) repair alone with arthroscopic ALL repair and reinforcement by the inferior extensor retinaculum (IER) for chronic ankle instability (CAI).

MATERIALS AND METHODS

All patients who underwent arthroscopic repair for CAI between 2017 and 2019 were evaluated. The Japanese Society for Surgery of the Foot (JSSF) scale and self-administered foot evaluation questionnaire (SAFE-Q), and duration between the surgery and walking without any support, jogging, and complete return to sports were evaluated and compared. The exclusion criteria were (1) follow-up period of < 1 year after surgery, (2) the presence of associated ankle lesions requiring treatment during the same operative procedure, including patients with subfibular ossicle bigger than 5 mm on radiographs, chondral or osteochondral defect, bony impingement, deltoid ligament tear, fibular tendon pathology, or posterior ankle impingement, and (3) patients who underwent revision surgery.

RESULTS

We identified 126 patients who underwent surgery for CAI and subsequently excluded 36 patients on account of a short follow-up period (< 1 year), additional surgery, and previous surgery. The remaining 90 eligible patients included arthroscopic ALL repair alone (group A, n = 44) and arthroscopic ALL repair with reinforcement by the inferior extensor retinaculum (group G, n = 46) groups. There was no significant difference in the postoperative activities nor in the preoperative or postoperative JSSF scale and SAFE-Q between the two groups. However, significant differences were seen in the mean surgical time (15.5 ± 8.1 vs 20.1 ± 7.6, P = 0.013).

CONCLUSION

This study showed no difference in clinical outcomes between the two groups. However, arthroscopic ALL repair with reinforcement by IER resulted in a longer surgical time than arthroscopic ALL repair alone.

LEVEL OF EVIDENCE

Retrospective comparative study, level III.

Clinical outcomes of concurrent surgery with weight bearing after modified lasso-loop stitch arthroscopic ankle stabilization

PURPOSE

To determine the effects of unilateral and bilateral ankle stabilization surgery with or without additional concurrent procedures for other pathologies on return to activity in patients who were allowed unrestricted weight bearing postoperatively.

METHODS

Ninety-three athletes underwent 120 ankle stabilization surgeries including 27 that underwent bilateral simultaneous surgery using the all-inside arthroscopy-modified lasso-loop technique and were divided into two groups: arthroscopic ligament repair alone without concurrent procedures (group A) and with simultaneous procedures for other pathologies (group B). Group A was further subdivided into unilateral (group A1) and simultaneous bilateral ankle surgery (group A2), and group B into ankle stabilization surgery with simultaneous procedures not requiring weight bearing postoperatively (Group B1) and with concurrent procedures allowing weight bearing (Group B2). Return to activity postoperatively was assessed by recording the time to walk without any support, jog, and return to full athletic activities. Clinical outcomes were assessed preoperatively and 12 months postoperatively using a subjective clinical score.

RESULTS

The average time between surgery and unsupported walk, jog, and return to full athletic activities was 1.6 ± 2.5, 16.9 ± 3.7, and 42.4 ± 19.3 days in group A, 17.2 ± 19.6, 34.5 ± 20.8, and 60.9 ± 22.8 days in group B, 1.7 ± 2.9, 16.1 ± 2.4, and 41.6 ± 18.2 days in group A1, 1.3 ± 0.6, 18.9 ± 5.5, and 44.6 ± 22.5 days in group A2, 25.3 ± 20.2, 43.3 ± 21.1, and 70.7 ± 23.1 days in group B1, and 4.8 ± 11.7, 20.7 ± 11.7, and 45.0 ± 13.7 days in group B2, respectively. These results indicate that the patients in group B2 showed a statistically significant faster time to return to activity than did those restricted from weight bearing. Differences in ankle stabilization alone between patients in groups A1 and A2 as well as groups B2 and A were not statistically significant. Clinical outcomes were similar for patients in groups B2 and A1 versus group A2.

CONCLUSION

Time to return to activity and clinical outcomes after ankle stabilization surgery using the modified lasso-loop technique were negatively affected if simultaneous bilateral surgery or simultaneous concurrent procedures were added or if weight bearing was unrestricted. However, a delay in return to athletic activity was observed when ankle stabilization surgery was performed using the modified lasso-loop technique with concurrent procedures that require non-weight bearing postoperatively.

LEVEL OF EVIDENCE

Level III.

Anatomy of Ankle Syndesmotic Ligaments: A Systematic Review of Cadaveric Studies

Diagnosis and management of isolated syndesmotic injuries are controversial and highly debated. Hence, the aim of this study is to explore and gain the current understanding pertaining to detailed anatomy of syndesmotic ligaments through a systematic review of published cadaveric studies. A systematic review was conducted online for literature published in English using PubMed and Google Scholar, as per PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) guidelines, up to April 30, 2019. Predefined eligibility criteria were applied, and the data thus compiled was analyzed. Study quality was assessed based on Quality Appraisal for Cadaveric Studies (QUACS) scale. A total of 12 studies reporting 365 ankles were included in this review. Considerable inconsistency in the naming and description of syndesmotic ligaments was observed, with only 2 studies reporting the vasculature of the ligaments. Hence further investigation of the anatomy of the syndesmotic ligaments is recommended so as to better inform clinical practice, as awareness of anatomy is critical for assessment, healing, and successful surgical management.Levels of Evidence: Level III: Systematic review of anatomical dissections.

Identification of Surgical Plan for Syndesmotic Fixation Procedure Based on Finite Element Method

Syndesmosis injuries account for approximately 20% of ankle fractures that require surgery. Although multiple surgical options are available, all of them are based on metal screws. Serious complications that arise when applying metal screws include screw loosening or breakage. To prevent such complications, we applied a simulation method using a finite element (FE) analysis. We created a 3D FE model of an ankle joint and conducted an FE analysis focusing on syndesmosis in terms of the level, material, and diameter of the syndesmotic screw and the number of penetrated cortical bones. The magnitude and direction of the force applied to the tibia in the midstance state were considered for simulating the model. The maximum von-Mises stress and syndesmosis widening were analyzed in terms of different biomechanical parameters. We identified the characteristics of the most biomechanically stable syndesmotic screw and its fixation point on the basis of the two parameters. We demonstrated that the ideal syndesmotic screw fixation should be fixed at a level 20 to 25 mm above the ankle using a 4.5 mm titanium screw.

An extended discrete element method for the estimation of contact pressure at the ankle joint during stance phase

Abnormalities in the ankle contact pressure are related to the onset of osteoarthritis. In vivo measurements are not possible with currently available techniques, so computational methods such as the finite element analysis (FEA) are often used instead. The discrete element method (DEM), a computationally efficient alternative to time-consuming FEA, has also been used to predict the joint contact pressure. It describes the articular cartilage as a bed of independent springs, assuming a linearly elastic behaviour and absence of relative motion between the bones. In this study, we present the extended DEM (EDEM) which is able to track the motion of talus over time. The method was used, with input data from a subject-specific musculoskeletal model, to predict the contact pressure in the ankle joint during gait. Results from EDEM were also compared with outputs from conventional DEM. Predicted values of contact area were larger in EDEM than they were in DEM (4.67 and 4.18 cm², respectively). Peak values of contact pressure, attained at the toe-off, were 7.3 MPa for EDEM and 6.92 MPa for DEM. Values predicted from EDEM fell well within the ranges reported in the literature. Overall, the motion of the talus had more effect on the extension and shape of the pressure distribution than it had on the magnitude of the pressure. The results indicated that EDEM is a valid methodology for the prediction of ankle contact pressure during daily activities.

[Effectiveness comparison of open reduction and internal fixation for open and closed ankle Logsplitter fractures]

Objective

To investigate the effectiveness of open reduction and internal fixation on high-energy ankle Logsplitter injuries (a kind of transsyndesmotic ankle fracture dislocation), and compare the prognosis between open and closed Logsplitter fracture.

Methods

The clinical data of 36 Logsplitter fractures treated with open reduction and internal fixation between April 2011 and May 2016 were retrospectively analyzed. Among them, 15 cases were open fracture and dislocation (open group) and 21 cases were closed fracture and dislocation (closed group). There was no significant difference between the two groups in gender, age, combined injury, injury to hospital admission time, and other general data ( P>0.05), with comparability. The wound healing, ankle mobility recovery, complications, and fracture healing were observed after operation. The ankle function was evaluated by the American Orthopaedic Foot and Ankle Society (AOFAS) score.

Results

Both groups were followed up 12-29 months (mean, 19 months). There was no significant difference in the follow-up time between the open group and the closed group ( t=1.169, P=0.251). In the open group, there were 3 cases of postoperative infection, 3 cases of nonunion, and 5 cases of post-traumatic osteoarthritis; the above complications occurred in 1 case in the closed group; there was no significant difference in complications between the two groups ( P=0.41) except post-traumatic osteoarthritis ( P=0.02). At last follow-up, there was no significant difference in AOFAS score between the two groups ( t=1.981, P=0.056). According to AOFAS score criterion, the results were good in 10 cases and general in 5 cases in the open group, and good in 13 cases and general in 8 cases in the closed group, showing no significant difference ( P=0.45). There was no significant difference in the fracture healing time and ankle flexion, dorsal extension, varus, and valgus motion between the two groups ( P>0.05).

Conclusion

Open reduction and internal fixation for open or closed Logsplitter fractures can achieve satisfactory results, improve fracture healing rate, effectively reduce the incidence of complications, and improve ankle function.

A model-based tracking method for measuring 3D dynamic joint motion using an alternating biplane x-ray imaging system

PURPOSES

To propose a new model-based tracking method for measuring three-dimensional (3D) dynamic joint kinematics using a clinical alternating biplane x-ray imaging system; and to quantify in vitro its errors in measuring ankle and knee motions at different motion speeds.

METHODS

A new model-based tracking method based on motion component partition and interpolation (MCPI) was developed for measuring 3D dynamic joint kinematics based on a clinical alternating biplane x-ray imaging system. Two detectors of the biplane imaging system placed perpendicular to each other were operated to collect alternating fluoroscopic images of the targeted joint during tasks. The CT data of the joint were also acquired for the reconstruction of volumetric and surface models of each of the associated bones. The CT-based models of the bones were first registered to the alternating images using a model-to-single-plane fluoroscopic image registration method, and the resulting bone poses were then refined using a two-level optimization with motion component partition and model vertex trajectory interpolation. The MCPI method was evaluated in vitro for measurement errors for an ankle and a knee specimen moving at different speeds against a standard reference provided by a highly accurate motion capture system. The positional and rotational errors of the measured bone poses were quantified in terms of the bias, precision, and root-mean-squared errors (RMSE), as well as the mean target registration error (mTRE), a final mTRE less than 2.5 mm indicating a successful registration.

RESULTS

The new method was found to have RMSE of bone pose measurements of less than 0.18 mm for translations and 0.72° for rotations for the ankle, and 0.33 mm and 0.74° for the knee with a high successful registration rate (>97%), and did not appear to be affected by joint motion speeds. Given the same alternating fluoroscopic images, the MCPI method outperformed the typical biplane analysis method assuming zero time offset between the two fluoroscopic views. The differences in performance between the methods were increased with increased joint motion speed. With the accurate bone pose data, the new method enabled talocrural, subtalar, and tibiofemoral kinematics measurements with submillimeter and subdegree accuracy, except for an RMSE of 1.04° for the internal/external rotation of the talocrural joint.

CONCLUSIONS

A new model-based tracking method based on MCPI has been developed for measuring dynamic joint motions using an alternating biplane x-ray imaging system widely available in medical centers. The MCPI method has been demonstrated in vitro to be highly accurate in determining the 3D kinematics of the bones of both the ankle joint complex and the knee. The current results suggest that the MCPI method would be an effective approach for measuring in vivo 3D kinematics of dynamic joint motion in a clinical setting equipped with an alternating biplane x-ray imaging system.

Anatomic feature of deltoid ligament attachment in posteromedial osteochondral lesion of talar dome

BACKGROUND

Osteochondral lesions of the talus (OLT) are recognized as being commonly associated with trauma. However, the etiology of OLT remains unclear. In the case of a posteromedial lesion of OLT (medial OLT), the deep layer of the deltoid ligament is located close to the medial OLT, and this relationship between a medial lesion and deltoid ligament could be a risk factor for medial OLT. The purpose of this study is to investigate the unique anatomic feature of the deep deltoid attachment to the talus in patients with medial OLT compared with patients with non-medial OLT.

METHODS

Forty ankles with medial OLT and 40 ankles without medial OLT were retrospectively reviewed in this study. On the coronal images of MRI, the attachment of deltoid ligament was measured. The continuity of the osteochondral fragment and its bed was evaluated on MRI and arthroscopic findings.

RESULTS

Coronal MRI images showed that the attachment of the deep deltoid ligament to the medial OLT was broader and located more proximally than in non-medial OLT. The continuity of fibers from the insertion site of deltoid ligament to the talus to the osteochondral fragment was observed (76.7%). In the arthroscopic findings, the osteochondral fragment was obviously connected to the talus at the medial site in 85.2% of feet.

CONCLUSIONS

The location of the deep deltoid ligament attachment to the medial OLT was more proximal and there was the possibility of these anatomic feature might contribute to the pathogenesis of medial OLT.

Musculoskeletal modelling of human ankle complex: Estimation of ankle joint moments

BACKGROUND

A musculoskeletal model for the ankle complex is vital in order to enhance the understanding of neuro-mechanical control of ankle motions, diagnose ankle disorders and assess subsequent treatments. Motions at the human ankle and foot, however, are complex due to simultaneous movements at the two joints namely, the ankle joint and the subtalar joint. The musculoskeletal elements at the ankle complex, such as ligaments, muscles and tendons, have intricate arrangements and exhibit transient and nonlinear behaviour.

METHODS

This paper develops a musculoskeletal model of the ankle complex considering the biaxial ankle structure. The model provides estimates of overall mechanical characteristics (motion and moments) of ankle complex through consideration of forces applied along ligaments and muscle-tendon units. The dynamics of the ankle complex and its surrounding ligaments and muscle-tendon units is modelled and formulated into a state space model to facilitate simulations. A graphical user interface is also developed during this research in order to include the visual anatomical information by converting it to quantitative information on coordinates.

FINDINGS

Validation of the ankle model was carried out by comparing its outputs with those published in literature as well as with experimental data obtained from an existing parallel ankle rehabilitation robot.

INTERPRETATION

Qualitative agreement was observed between the model and measured data for both, the passive and active ankle motions during trials in terms of displacements and moments.

The Role of Fluid Dynamics in Distributing Ankle Stresses in Anatomic and Injured States

BACKGROUND

In 1976, Ramsey and Hamilton published a landmark cadaveric study demonstrating a dramatic 42% decrease in tibiotalar contact area with only 1 mm of lateral talar shift. An increase in maximum principal stress of at least 72% is predicted based on these findings though the delayed development of arthritis in minimally misaligned ankles does not appear to be commensurate with the results found in dry cadaveric models. We hypothesized that synovial fluid could be a previously unrecognized factor that contributes significantly to stress distribution in the tibiotalar joint in anatomic and injured states.

METHODS

As it is not possible to directly measure contact stresses with and without fluid in a cadaveric model, finite element analysis (FEA) was employed for this study. FEA is a modeling technique used to calculate stresses in complex geometric structures by dividing them into small, simple components called elements. Four test configurations were investigated using a finite element model (FEM): baseline ankle alignment, 1 mm laterally translated talus and fibula, and the previous 2 bone orientations with fluid added. The FEM selected for this study was the Global Human Body Models Consortium-owned GHBMC model, M50 version 4.2, a model of an average-sized male (distributed by Elemance, LLC, Winston-Salem, NC). The ankle was loaded at the proximal tibia with a distributed load equal to the GHBMC body weight, and the maximum principal stress was computed.

RESULTS

All numerical simulations were stable and completed with no errors. In the baseline anatomic configuration, the addition of fluid between the tibia, fibula, and talus reduced the maximum principal stress computed in the distal tibia at maximum load from 31.3 N/mm² to 11.5 N/mm². Following 1 mm lateral translation of the talus and fibula, there was a modest 30% increase in the maximum stress in fluid cases. Qualitatively, translation created less high stress locations on the tibial plafond when fluid was incorporated into the model.

CONCLUSIONS

The findings in this study demonstrate a meaningful role for synovial fluid in distributing stresses within the ankle that has not been considered in historical dry cadaveric studies. The increase in maximum stress predicted by simulation of an ankle with fluid was less than half that projected by cadaveric data, indicating a protective effect of fluid in the injured state. The trends demonstrated by these simulations suggest that bony alignment and fluid in the ankle joint change loading patterns on the tibia and should be accounted for in future experiments.

CLINICAL RELEVANCE

Synovial fluid may play a protective role in ankle injuries, thus delaying the onset of arthritis. Reactive joint effusions may also function to additionally redistribute stresses with higher volumes of viscous fluid.

Biomechanical evaluation of syndesmotic screw design via finite element analysis and Taguchi's method

BACKGROUND

Screw fixation of syndesmotic injuries facilitates ligament healing and restoration of ankle stability, but failure of the screw might threaten the success of the treatment. Screw design parameters, such as outer diameter, inner diameter, thread pitch, leading edge radius, trailing edge radius, leading edge angle, and trailing edge angle, might have effects on the stresses that occur in the screws. This is the first study, to our knowledge, to investigate which geometric screw parameters play key roles in stresses that occur in screws used for syndesmotic fixation.

METHODS

A three-dimensional finite element model of an ankle was reconstructed. Four different types of titanium screws—4.5-mm malleolar, 4-mm cancellous, 4-mm machine, and 3.5-mm cortical—were placed on this model. Physiologic load was applied to evaluate the stress in the screw. Then the contribution of each design factor to stress in the screws was analyzed systematically by Taguchi's robust design method.

RESULTS

The maximum equivalent ductile failure (von Mises equivalent stress) value was found in the 4-mm cancellous screw (402 MPa). Taguchi's analysis showed that the descending order of contribution of the design factors to stress emerging on the screw is inner diameter, leading edge angle, thread pitch, outer diameter, and trailing edge angle.

CONCLUSIONS

Stress that occurs in syndesmotic screws is closely related to their geometry and dimensions. According to the results, a 3.5-mm cortical screw with the ideal screw design regarding optimal parameters to resist against stresses in the syndesmosis seems more reasonable to choose in syndesmotic fixation.

A modified and enhanced test setup for biomechanical investigations of the hindfoot, for example in tibiotalocalcaneal arthrodesis

Background

Tibiotalocalcaneal arthrodesis (TTCA) using intramedullary nails is a salvage procedure for many diseases in the ankle and subtalar joint. Despite “newly described intramedullary nails” with specific anatomical shapes there still remain major complications regarding this procedure. The following study presents a modified biomechanical test setup for investigations of the hindfoot.

Methods

Nine fresh-frozen specimens from below the human knee were anaysed using the Hindfoot Arthrodesis Nail (Synthes) instrument. Quasi-static biomechanical testing was performed for internal/external rotation, varus/valgus and dorsal/plantar flexion using a modified established setup (physiological load entrance point, sledge at lever arm to apply pure moments). Additionally, a 3D optical measurement system was added to allow determination of interbony movements.

Results

The mean torsional range of motion (ROM) calculated from the actuator data of a material testing machine was 10.12° (SD 0.6) compared to 10° (SD 2.83) as measured with the Optotrak® system (between tibia and calcaneus). The Optotrak showed 40 % more rotation in the talocrural joint.

Mean varus/valgus ROM from the material testing flexion machine was seen to be 5.65° (SD 1.84) in comparison to 2.82° (SD 0.46) measured with the Optotrak. The subtalar joint showed a 70 % higher movement when compared to the talocrural joint.

Mean ROM in the flexion test was 5.3° (SD 1.45) for the material testing machine and 2.1° (SD 0.39) for the Optotrak. The movement in the talocrural joint was 3 times higher compared to the subtalar joint.

Conclusion

The modified test setup presented here for the hindfoot allows a physiological biomechanical loading. Moreover, a detailed characterisation of the bone-implant constructs is possible.

Efficient Computation of Cartilage Contact Pressures within Dynamic Simulations of Movement

The objective of this study was to assess the use of an advanced collision detection algorithm to simulate cartilage contact pressure patterns within dynamic musculoskeletal simulations of movement. We created a knee model that included articular cartilage contact for the tibiofemoral and patellofemoral joints. Knee mechanics were then predicted within the context of a dynamic gait simulation. At each time step of a simulation, ray-casting was used in conjunction with hierarchical oriented bounding boxes (OBB) to rapidly identify regions of overlap between articulating cartilage surfaces. Local cartilage contact pressure was then computed using an elastic foundation model. Collision detection implemented in parallel on a GPU provided up to a 10× speed increase when using high resolution mesh densities that had >10 triangles/mm2. However, pressure magnitudes converged at considerably lower mesh densities (2.6 triangles/mm2) where CPU and GPU implementations of collision detection exhibited equivalent performance. Simulated tibiofemoral contact locations were comparable to prior experimental measurements, while pressure magnitudes were similar to those predicted by finite element models. We conclude the use of ray-casting with hierarchical OBB for collision detection is a viable method for simulating joint contact mechanics in human movement.

Foot-ankle simulators: A tool to advance biomechanical understanding of a complex anatomical structure

In vitro gait simulations have been available to researchers for more than two decades and have become an invaluable tool for understanding fundamental foot-ankle biomechanics. This has been realised through several incremental technological and methodological developments, such as the actuation of muscle tendons, the increase in controlled degrees of freedom and the use of advanced control schemes. Furthermore, in vitro experimentation enabled performing highly repeatable and controllable simulations of gait during simultaneous measurement of several biomechanical signals (e.g. bone kinematics, intra-articular pressure distribution, bone strain). Such signals cannot always be captured in detail using in vivo techniques, and the importance of in vitro experimentation is therefore highlighted. The information provided by in vitro gait simulations enabled researchers to answer numerous clinical questions related to pathology, injury and surgery. In this article, first an overview of the developments in design and methodology of the various foot-ankle simulators is presented. Furthermore, an overview of the conducted studies is outlined and an example of a study aiming at understanding the differences in kinematics of the hindfoot, ankle and subtalar joints after total ankle arthroplasty is presented. Finally, the limitations and future perspectives of in vitro experimentation and in particular of foot-ankle gait simulators are discussed. It is expected that the biofidelic nature of the controllers will be improved in order to make them more subject-specific and to link foot motion to the simulated behaviour of the entire missing body, providing additional information for understanding the complex anatomical structure of the foot.

Ankle Arthroscopic Reconstruction of Lateral Ligaments (Ankle Anti-ROLL)

Ankle instability is a condition that often requires surgery to stabilize the ankle joint that will improve pain and function if nonoperative treatments fail. Ankle stabilization surgery may be performed as a repair in which the native existing anterior talofibular ligament or calcaneofibular ligament (or both) is imbricated or reattached. Alternatively, when native ankle ligaments are insufficient for repair, a reconstruction of the ligaments may be performed in which an autologous or allograft tendon is used to reconstruct the anterior talofibular ligament or calcaneofibular ligament (or both). Currently, ankle stabilization surgery is most commonly performed through an open incision, but arthroscopic ankle stabilization using repair techniques has been described and is being used more often. We present our technique for anatomic ankle arthroscopic reconstruction of the lateral ligaments (anti-ROLL) performed in an all-inside-out manner that is likely safe for patients and minimally invasive.

Biomechanical evaluation of syndesmotic screw position: a finite-element analysis

OBJECTIVES

To evaluate the stresses in syndesmotic screws and widening of syndesmosis under loading after placement of the screws at different levels from the ankle joint line and to determine the optimal level.

METHODS

From a set of computed tomographic data of an ankle, a 3-dimensional finite-element model was reconstructed. Six fixation configurations of the syndesmosis with placement of 3.5 or 4.5 mm single tricortical screws at 20-45 mm from the tibiotalar joint were performed on this model. Physiological loads approximating those during both midstance and heel-off states of stance phase of normal walking were applied to evaluate the stress in the screw and widening of the syndesmosis.

RESULTS

Among the 6 fixation configurations, the lowest von Mises stress was found in the screws placed 30-40 mm above the joint line (373.31-380.17 MPa for 3.5 mm cortical screw and 284.06-327.31 MPa for 4.5 mm cortical screw in midstance phases), whereas the least syndesmosis widening was determined when the screw was placed 30 mm above the tibial plafond (0.005 mm) for 3.5 mm cortical screw and 20, 25, and 30 mm above the tibial plafond (0.004 mm for each, respectively) for 4.5 mm cortical screw during midstance phases.

CONCLUSIONS

This study showed that syndesmosis fixation at the level of 30-40 mm above the tibiotalar joint has advantages with regard to stress in screws in comparison with the other evaluated levels.

Three-dimensional finite element analysis used to compare six different methods of syndesmosis fixation with 3.5- or 4.5-mm titanium screws: a biomechanical study

BACKGROUND

Use of thicker and longer (four cortices) screws or of multiple screws seems to be more stable and efficient for syndesmosis fixation.

METHODS

A three-dimensional finite element model of an ankle was constructed from serial axial sections from an existing two-dimensional computed tomographic image. Constructions of syndesmosis fixation with 3.5-mm single tricortical, 3.5-mm single quadricortical, 3.5-mm double tricortical, 3.5-mm double quadricortical, 4.5-mm single tricortical, and 4.5-mm single quadricortical screws were performed on this model. Physiologic loads approximating those during stance phase normal walking were applied to this ankle system. Stress values on the screws using the six fixation methods were compared.

RESULTS

The highest maximum stress was determined over 3.5-mm cortical screws applied as single quadricortical, and the lowest maximum stress was determined over the 4.5-mm cortical screw applied as single quadricortical. Stress on the 3.5-mm single screw with quadricortical application was found to be higher than that with tricortical application and also compared with the 4.5-mm quadricortical screw application. Differences between the 4.5-mm single tricortical and quadricortical screws and between the 3.5-mm single tricortical and 3.5-mm double tricortical screw applications were not significant.

CONCLUSIONS

Quadricortical application of 3.5-mm single screws and tricortical application of 3.5-mm double cortical screws are not good choices for syndesmosis fixation. If the plan is tricortical application, a 3.5-mm single cortical screw is adequate. If quadricortical application of syndesmosis fixation is planned, a 4.5-mm cortical screw should be used.

Trabecular evidence for a human-like gait in Australopithecus africanus

Although the earliest known hominins were apparently upright bipeds, there has been mixed evidence whether particular species of hominins including those in the genus Australopithecus walked with relatively extended hips, knees and ankles like modern humans, or with more flexed lower limb joints like apes when bipedal. Here we demonstrate in chimpanzees and humans a highly predictable and sensitive relationship between the orientation of the ankle joint during loading and the principal orientation of trabecular bone struts in the distal tibia that function to withstand compressive forces within the joint. Analyses of the orientation of these struts using microCT scans in a sample of fossil tibiae from the site of Sterkfontein, of which two are assigned to Australopithecus africanus, indicate that these hominins primarily loaded their ankles in a relatively extended posture like modern humans and unlike chimpanzees. In other respects, however, trabecular properties in Au africanus are distinctive, with values that mostly fall between those of chimpanzees and humans. These results indicate that Au. africanus, like Homo, walked with an efficient, extended lower limb.

Changes in in vitro compressive contact stress in the rat tibiofemoral joint with varus loading

Increased compression of the tibiofemoral joint, due to increased body mass or malalignment, is a risk factor for the onset and progression of osteoarthritis. This work investigates compressive stresses and contact areas in the articular cartilage of the rat tibiofemoral joint during standing with different applied varus loads. Cadaver rat knees underwent loading of the extensors combined with varus loading (0%, 50% or 100% of bodyweight) of the tibiofemoral joint. Articular cartilage contact stress was evaluated using stereophotogrammetric measurements of biplanar radiographs, high-resolution micro-computed tomography and discrete element analysis. Random coefficients regression models were used to analyze the relationship between peak and spatially averaged contact stresses and contact areas as a function of increasing varus loadings. The contact stresses increased linearly in the medial compartment. Peak stress significantly increased 0.042 MPa (p=0.006) and spatially averaged stress significantly increased 0.029 MPa (p=0.045) for each 10% increase in varus loading. There was a trend for a small decrease in contact areas in the lateral compartment with varus loading. This is the first report of the contact stresses in a rat tibiofemoral joints under simulated weight bearing conditions. The 0.42 MPa increase in peak contact stress at the cartilage-cartilage interface of the medial compartment with 100% bodyweight varus load is similar to the reported change in peak contact stress associated with development of symptomatic knee osteoarthritis in humans. Determination of contact stresses in rat tibiofemoral joints allows comparison to contact stresses in humans with the development of osteoarthritis.

Anatomy of the distal tibiofibular syndesmosis in adults: a pictorial essay with a multimodality approach

A syndesmosis is defined as a fibrous joint in which two adjacent bones are linked by a strong membrane or ligaments.This definition also applies for the distal tibiofibular syndesmosis, which is a syndesmotic joint formed by two bones and four ligaments. The distal tibia and fibula form the osseous part of the syndesmosis and are linked by the distal anterior tibiofibular ligament, the distal posterior tibiofibular ligament, the transverse ligament and the interosseous ligament. Although the syndesmosis is a joint, in the literature the term syndesmotic injury is used to describe injury of the syndesmotic ligaments. In an estimated 1–11% of all ankle sprains, injury of the distal tibiofibular syndesmosis occurs. Forty percent of patients still have complaints of ankle instability 6 months after an ankle sprain. This could be due to widening of the ankle mortise as a result of increased length of the syndesmotic ligaments after acute ankle sprain. As widening of the ankle mortise by 1 mm decreases the contact area of the tibiotalar joint by 42%, this could lead to instability and hence early osteoarthritis of the tibiotalar joint. In fractures of the ankle, syndesmotic injury occurs in about 50% of type Weber B and in all of type Weber C fractures. However,in discussing syndesmotic injury, it seems the exact proximal and distal boundaries of the distal tibiofibular syndesmosis are not well defined. There is no clear statement in the Ashhurst and Bromer etiological, the Lauge-Hansen genetic or the Danis-Weber topographical fracture classification about the exact extent of the syndesmosis. This joint is also not clearly defined in anatomical textbooks, such as Lanz and Wachsmuth. Kelikian and Kelikian postulate that the distal tibiofibular joint begins at the level of origin of the tibiofibular ligaments from the tibia and ends where these ligaments insert into the fibular malleolus. As the syndesmosis of the ankle plays an important role in the stability of the talocrural joint, understanding of the exact anatomy of both the osseous and ligamentous structures is essential in interpreting plain radiographs, CT and MR images, in ankle arthroscopy and in therapeutic management. With this pictorial essay we try to fill the hiatus in anatomic knowledge and provide a detailed anatomic description of the syndesmotic bones with the incisura fibularis, the syndesmotic recess, synovial fold and tibiofibular contact zone and the four syndesmotic ligaments. Each section describes a separate syndesmotic structure, followed by its clinical relevance and discussion of remaining questions.

The relation between geometry and function of the ankle joint complex: a biomechanical review

This review deals with the relation between the anatomy and function of the ankle joint complex. The questions addressed are how high do the forces in the ankle joint get, where can the joints go (range of motion) and where do they go during walking and running. Finally the role of the ligaments and the articular surfaces is discussed, i.e. how does it happen. The magnitude of the loads on the ankle joint complex are primarily determined by muscle activity and can be as high as four times the body weight during walking. For the maximal range of motion, plantar and dorsiflexion occurs in the talocrural joint and marginally at the subtalar joint. In-eversion takes place at both levels. The functional range of motion is well within the limits of the maximal range of motion. The ligaments do not contribute to the forces for the functional range of motion but determine the maximal range of motion together with the articular surfaces. The geometry of the articular surfaces primarily determines the kinematics. Clinical studies must include these anatomical aspects to better understand the mechanism of injury, recovery, and interventions. Models can elucidate the mechanism by which the anatomy relates to the function. The relation between the anatomy and mechanical properties of the joint structures and joint function should be considered for diagnosis and treatment of ankle joint pathology.