Dissolving and Swelling Hydrogel-Based Microneedles: An Overview of Their Materials, Fabrication, Characterization Methods, and Challenges

Research Progress of Hydrogel Microneedles in Wound Management

Microneedles are a novel drug delivery system that offers advantages such as safety, painlessness, minimally invasive administration, simplicity of use, and controllable drug delivery. As a type of polymer microneedle with a three-dimensional network structure, hydrogel microneedles (HMNs) possess excellent biocompatibility and biodegradability and encapsulate various therapeutic drugs while maintaining drug activity, thus attracting significant attention. Recently, they have been widely employed to promote wound healing and have demonstrated favorable therapeutic effects. Although there are reviews about HMNs, few of them focus on wound management. Herein, we present a comprehensive overview of the design and preparation methods of HMNs, with a particular emphasis on their application status in wound healing, including acute wound healing, infected wound healing, diabetic wound healing, and scarless wound healing. Finally, we examine the advantages and limitations of HMNs in wound management and provide suggestions for future research directions.

Hydrogel Microneedles with Programmed Mesophase Transitions for Controlled Drug Delivery

Microneedle-based drug delivery offers an attractive and minimally invasive administration route to deliver therapeutic agents through the skin by bypassing the stratum corneum, the main skin barrier. Recently, hydrogel-based microneedles have gained prominence for their exceptional ability to precisely control the release of their drug cargo. In this study, we investigated the feasibility of fabricating microneedles from triblock amphiphiles with linear poly(ethylene glycol) (PEG) as the hydrophilic middle block and two dendritic side-blocks with enzyme-cleavable hydrophobic end-groups. Due to the poor formation and brittleness of microneedles made from the neat amphiphile, we added a sodium alginate base layer and tested different polymeric excipients to enhance the mechanical strength of the microneedles. Following optimization, microneedles based on triblock amphiphiles were successfully fabricated and exhibited favorable insertion efficiency and low height reduction percentage when tested in Parafilm as a skin-simulant model. When tested against static forces ranging from 50 to 1000 g (4.9-98 mN/needle), the microneedles showed adequate mechanical strength with no fractures or broken segments. In buffer solution, the solid microneedles swelled into a hydrogel within about 30 s, followed by their rapid disintegration into small hydrogel particles. These hydrogel particles could undergo slow enzymatic degradation to soluble polymers. In vitro release study of dexamethasone (DEX), as a steroid model drug, showed first-order drug release, with 90% released within 6 days. Eventually, DEX-loaded MNs were subjected to an insertion test using chicken skin and showed full penetration. This study demonstrates the feasibility of programming hydrogel-forming microneedles to undergo several mesophase transitions and their potential application as a delivery system for self-administration, increased patient compliance, improved efficacy, and sustained drug release.

3D Printing of Biodegradable Polymeric Microneedles for Transdermal Drug Delivery Applications

Microneedle (MN) technology is an optimal choice for the delivery of drugs via the transdermal route, with a minimally invasive procedure. MN applications are varied from drug delivery, cosmetics, tissue engineering, vaccine delivery, and disease diagnostics. The MN is a biomedical device that offers many advantages including but not limited to a painless experience, being time-effective, and real-time sensing. This research implements additive manufacturing (AM) technology to fabricate MN arrays for advanced therapeutic applications. Stereolithography (SLA) was used to fabricate six MN designs with three aspect ratios. The MN array included conical-shaped 100 needles (10 × 10 needle) in each array. The microneedles were characterized using optical and scanning electron microscopy to evaluate the dimensional accuracy. Further, mechanical and insertion tests were performed to analyze the mechanical strength and skin penetration capabilities of the polymeric MN. MNs with higher aspect ratios had higher deformation characteristics suitable for penetration to deeper levels beyond the stratum corneum. MNs with both 0.3 mm and 0.4 mm base diameters displayed consistent force-displacement behavior during a skin-equivalent penetration test. This research establishes guidelines for fabricating polymeric MN for high-accuracy and low-cost 3D printing.