Sunlight Assisted Photocatalytic Degradation of Ciprofloxacin in Water Using Fe Doped ZnO Nanoparticles for Potential Public Health Applications

Photocatalytic degradation of antibiotics by N-doped carbon nanoflakes-nickel ferrite composite derived from algal biomass

This work reports the synthesis of nickel ferrite (NiFe) nanoparticles, N-doped mesoporous carbon nanoflakes (NCF) and novel nickel ferrite-carbon nanoflakes (NiFe@NCF) nanocomposite using solvothermal method. NCF was derived from a cyanobacterial consortium consisting of Anabaena, Lyngbya and Weistiellopsis, rich in carbon and nitrogen. The synthesized nanoparticles were used as heterogeneous photocatalyst for degradation of two harmful water pollutants, ciprofloxacin (CIP) and levofloxacin (LEV). 99.91% LEV and 98.86% CIP were degraded within 50 and 70 min of visible light irradiation using NiFe@NCF following pseudo first order kinetics. This improved efficiency of the nanocomposite may be attributed to its higher surface area, reduction of band gap (from 2.42 to 2.19 eV), more active sites as well as charge carrier mobility with decreasing agglomeration tendency of the magnetic nickel nanoparticles upon being embedded on NCF. N-doping improves light harvesting property, retards charge recombination and extends as well as delocalises ᴨ-conjugated system resulting in enhanced photocatalytic activity. The scavenging experiments and EPR analysis reveal that O2-• and •OH are the main active species taking part in the degradation process. The material performs well within a wide range of pH and can be effectively used up to 5 repetitive cycles. A feasible photocatalytic degradation mechanism of the antibiotics against NiFe@NCF nanocomposite is also put forwarded along with their possible degradation pathways from LCMS studies.

Degradation of cefixime by photocatalysis via Ba-doped BiFeO3 nanomaterial using RSM analysis under LED light source

In the current work, Response Surface Methodology (RSM)-a statistical method-is used to optimize procedures like photocatalysis with the least amount of laboratory testing. However, to determine the most effective model for achieving the maximum rate of removal efficiency, the Response Surface Methodology was employed. The Ba-doped BiFeO3 photocatalyst was synthesized by the co-precipitation method, and its intrinsic properties were investigated by utilizing a range of spectroscopic techniques, such as FESEM, EDX, XRD, FTIR, and UV-vis. Herein, four independent factors such as, pH, contact time, pollutant concentration, and catalyst dosage were chosen. The results revealed that under acidic conditions with a contact duration of 2 min, a moderate catalyst dosage, and higher pollutant concentration, a degradation rate of 89.8% was achieved. The regression coefficient (R2) and probability value (P) were determined to be 0.99551 and 0.0301, respectively, therefore confirming the excellent fit of the RSM model. Furthermore, this research investigated the potential photocatalytic degradation mechanisms of cefixime, demonstrating that the removal efficiency of cefixime is greatly influenced by the functional parameters.

Hydrothermal fabrication, characterization and RSM optimization of cobalt-doped zinc oxide nanoparticles for antibiotic photodegradation under visible light

Photodegradation is considered a significant method engaged for the elimination of organic pollutants from water. In this work, hydrothermal cobalt-doped zinc oxide nanoparticles (Hy-Co-ZnO NPs) loaded with 5, 10, and 15% cobalt were prepared in a hydrothermal way and were investigated as a photocatalyst for the Ciprofloxacin (CIPF) degradation under visible irradiation using LED-light. Characterization approaches such as FTIR, XRD, XPS, DRS UV-vis spectroscopy, SEM, TEM, BET, EDX and TGA were used for the investigation of the fabricated Hy-Co-ZnO NPs. The studies indicated that 10% Hy-Co-ZnO NPs was the most efficient catalyst for the CIPF photolysis compared to ZnO NPs and other Hy-Co-ZnO NPs with 5 and 15% cobalt content. Higher photocatalytic activity (> 98%) of 20 mg/L of CIPF solution was attained within 60 min. The reaction kinetics showed that the first-order model is suitable for displaying the rate of reaction and amount of CIPF elimination with R2 = 0.9883. Moreover, Central composite design (CCD) optimization of the 10% Hy-Co-ZnO NPs was also studied.

Photocatalytic degradation of fluoroquinolone antibiotics using chitosan biopolymer functionalized copper oxide nanoparticles prepared by facile sonochemical method

Photocatalytic degradation is an excellent method for removing pharmaceutical residues due to their simplicity, ecological benignity, high efficiency, and exceptional stability. Herein, we demonstrate the sonochemically synthesised chitosan biopolymer functionalized copper oxide nanoparticles as an efficient photocatalyst for the degradation of fluoroquinolone-based antibiotics. The X-ray diffraction Rietveld refinement revealed the formation of single-phase copper oxide (CuO) with a monoclinic structure. The presence of biopolymer functionalization was corroborated by Fourier Transform Infrared spectroscopy by observing the -NH2 and -OH functional groups. The high-resolution transmission electron microscopic images inferred that Chitosan functionalized copper oxide (C-CuO) particles are nano-sized with a smooth texture and aggregation-free particles. The strong absorbance and the broad photoluminescence emission in the ultraviolet-visible region confirm the suitability of CuO and C-CuO nanoparticles for photocatalytic applications. The catalytic activity was studied against fluoroquinolone-based antibiotics such as ciprofloxacin and norfloxacin under direct sunlight illumination. Interestingly, the C-CuO catalyst demonstrated 71.07 % (@140 min.) and 71.9 % (@60 min.) of degradation for ciprofloxacin and norfloxacin, respectively. The obtained photocatalytic activity of the prepared CuO and C-CuO catalysts was superior to the CuO particles prepared by the coprecipitation method (CC-CuO).

Cobalt-substituted ZnS QDs: a diluted magnetic semiconductor and efficient photocatalyst

Recently, understanding the origin of induced magnetic characteristics in transition metal atom-doped QDs has been a major focus owing to their potential applications in the area of spintronic devices. A detailed experimental and theoretical investigation was conducted to understand the physical properties of Co-doped ZnS QDs containing different weight percentages of Co atoms [CoxZn1-xS (x = 0.00, 0.03, 0.06, and 0.09)], prepared using chemical co-precipitation techniques. X-ray diffraction studies proved that all the prepared QDs formed an extremely pure cubic zinc blende crystallographic phase free of contaminants. The validation of the quantum dot nature of all the samples was provided by the HRTEM images, BET studies, and blue shift in the absorption spectra. Both the obtained FTIR and PL spectra at room temperature also confirmed the phase purity of the prepared QDs. The observed weak ferromagnetic behavior of the doped samples was due to the presence of p-d hybridization between the 3d levels of Co2+ ions and 3p levels of S2- ions of the host ZnS QDs. Hysteresis loops that were obtained at room temperature validated this weak ferromagnetic nature. These obtained results were also supported theoretically using DFT calculations. FDTD simulations provided a detailed explanation for the observed blue shift in the absorption spectra originating from the quantum confinement effect of doped and undoped ZnS QDs. The dielectric properties of all the samples were examined properly, and it was also found that the grain boundaries contributed effectively to providing the dielectric response. The doped ZnS sample containing more Co dopants at low frequencies showed a progressive rise in polarisation loss. In addition, Co-doped ZnS QDs are efficient photocatalysts. A pH-dependent photodegradation test of ciprofloxacin (CIP) antibiotic was conducted using 9% Co-doped ZnS QDs. It was observed that 9% Co-doped ZnS nanocatalysts has sufficient capability to degrade CIP to around 94.7% in a solution of pH 10 within one hour. Therefore, besides showing photocatalytic effects, Co-doped ZnS QDs act as ideal dilute magnetic semiconductors (DMSs) and will undoubtedly become excellent candidates for the microelectronics industry because of their special ability to exhibit spin-dependent magneto-electro-optical properties that find use in spin-polarized light-emitting diodes, solid-state lasers, and spin-transistor devices.

Potential antibacterial, antibiofilm, and photocatalytic performance of gamma-irradiated novel nanocomposite for enhanced disinfection applications with an investigated reaction mechanism

BACKGROUND

Water scarcity is now a global challenge due to the population growth and the limited amount of available potable water. In addition, modern industrialization, and microbial pathogenesis is resulting in water pollution on a large scale.

METHODS

In the present study, reusable Co0.5Ni0.5Fe2O4/SiO2/TiO2 composite matrix was incorporated with CdS NPs to develop an efficient photocatalyst, and antimicrobial agents for wastewater treatment, and disinfection purpose. The antibacterial performance of the gamma-irradiated samples was evaluated against various types of Gram-positive bacteria using ZOI, MIC, antibiofilm, and effect of UV-exposure. Antibacterial reaction mechanism was assessed by bacterial membrane leakage assay, and SEM imaging. In addition, their photocatalytic efficiency was tested against MB cationic dye as a typical water organic pollutant.

RESULTS

Our results showed that, the formed CdS NPs were uniformly distributed onto the surface of the nanocomposite matrix. While, the resulted CdS-based nanocomposite possessed an average particle size of nearly 90.6 nm. The antibacterial performance of the prepared nanocomposite was significantly increased after activation with gamma and UV irradiations. The improved antibacterial performance was mainly due to the synergistic effect of both TiO2 and CdS NPs; whereas, the highest photocatalytic efficiency of MB removal was exhibited in alkaline media due to the electrostatic attraction between the cationic MB and the negatively-charged samples. In addition, the constructed heterojunction enabled better charge separation and increased the lifetime of the photogenerated charge carriers.

CONCLUSION

Our results can pave the way towards the development of efficient photocatalysts for wastewater treatment and promising antibacterial agents for disinfection applications.

Upcycling of waste EPS beads to immobilized codoped TiO2 photocatalysts for ciprofloxacin degradation and E. coli disinfection under sunlight

The emerging global problem of antimicrobial resistance needs immediate attention. In this regard, this work demonstrates the use of expanded polystyrene waste in the synthesis of immobilized photocatalytic films for the treatment of antibiotics as well as for bacterial disinfection. A boron-cerium codoped TiO2 catalyst (of specific composition: B0.8Ce0.2TiO2) was immobilized in an expanded polystyrene (EPS) film prepared from waste EPS beads. These films were studied for the degradation of ciprofloxacin (CIP) and disinfection of E. coli under sunlight. The film with a catalyst loading of 20 wt% showed a maximum degradation of 89% in 240 min with a corresponding TOC reduction of 84%. A 7.4 and 6.3 log reduction from the bacterial inactivation studies in the presence and absence of antibiotics, respectively, was obtained. The EPS film was stable after five times of reuse, and no significant chemical changes in the used film were observed from FTIR analysis. The average thickness of the prepared film was found from FESEM analysis to be 1.09 mm. These EPS films were also tested for degradation of other antibiotics, such as norfloxacin, levofloxacin and moxifloxacin. The EPS films were tested in two different reactor volumes at optimum conditions. Also, the effectiveness of B0.8Ce0.2TiO2/EPS film in real water samples indicates its potential in large-scale and real-world applications. Thus, these B0.8Ce0.2TiO2/EPS films can be effectively employed for both degradation of ciprofloxacin and the disinfection of E. coli under solar light to solve the increasing problem of antimicrobial resistance.

Incorporation of Ag-doped ZnO nanorod through Graphite hybridization: Effective approach for degradation of Ciprofloxacin

To remove the Ciprofloxacin (CIP) from aqueous solution, ZnO-Ag-Gp nanocomposite exhibited efficient photocatalytic properties. The biopersistent CIP is pervasive in surface water and also hazardous to human and animal health. This study utilized the hydrothermal technique to prepare Ag-doped ZnO hybridizing Graphite (Gp) sheet (ZnO-Ag-Gp) to degrade pharmaceuticals pollutant CIP from an aqueous medium. The structural and chemical compositions of the photocatalysts were determined by XRD, FTIR and XPS analysis. FESEM and TEM images revealed the nanorod ZnO with round shape Ag distributed on a Gp surface. The reduced bandgap of the ZnO-Ag-Gp sample enhanced the photocatalytic property which was measured by using UV-vis Spectroscopy. Dose optimization study found that 1.2 g/L is optimum for single (ZnO) and binary (ZnO-Gp and ZnO-Ag), where 0.3 g/L ternary (ZnO-Ag-Gp) exhibited maximum degradation efficiency (98%) within 60 min for 5 mg/L CIP. Pseudo 1st order reaction kinetics rate was found highest for ZnO-Ag-Gp (0.05983 min^-1) and it decreased to 0.03428 min^-1 for annealed sample. Removal efficiency decreased to only 90.97% at 5th run and hydroxyl radicals played a vital role to degrade CIP from aqueous solution. UV/ZnO-Ag-Gp will be a promising technique to degrade wide-ranging pharmaceutical antibiotics from the aquatic medium.

Copper sulfide and zinc oxide hybrid nanocomposite for wastewater decontamination of pharmaceuticals and pesticides

In this work, hybrid nanocomposites of CuS QDs @ ZnO photocatalysts are fabricated through a facile microwave-assisted (MW) hydrothermal method as a green preparation process. The prepared photocatalysts (PCs) are employed under simulated sunlight (SL) for the degradation of ciprofloxacin, ceftriaxone, ibuprofen pharmaceuticals, methylene blue dye, and 2,4,5-trichlorophenoxyacetic acid (2,4-D) pesticide. The prepared photocatalysts are characterized in detail using several compositional, optical, and morphological techniques. The influence of the CuS (QDs) wt. % on morphological, structural, as well as photocatalytic degradation efficiency have been investigated. The small displacement between the (107) plane of CuS and the (102) plane of ZnO can confirmed the existence of lattice interaction, implying the formation of p-n heterojunctions. TEM and XRD results demonstrated that the CuS QDs are established and uniformly decorated on the surface of ZnO NRs, confirming the forming of an efficient CuS QDs @ ZnO heterojunction nanostructures. The CuS QDs @ ZnO hybrid nanocomposites showed enhancement in crystallinity, light absorption, surface area, separation of e-h pair and inhibition in their recombination at an interfacial heterojunction. In addition it is found that, 3 wt% CuS QDs @ ZnO has the foremost influence. The results showed improvement of photocatalytic activity of the 3% CuS QDs @ ZnO hybrid nanocomposite as compared to the bare ZnO nanorods. The impressive photocatalytic performance of CuS @ ZnO heterostructure nanorods may be attributed to efficient charge transfer. The prepared CuS QDs @ ZnO hybrid nanocomposites exhibited 100% removal for MB dye, after 45 min, and after 60 min for ibuprofen, ciprofloxacin pharmaceuticals, and 2.4.5 trichloro phenoxy acetic acid pesticide with the catalyst amount of 0.2 g/L. Although 100% removal of ceftriaxone pharmaceutical acheived after 90 min. In addition CuS QDs @ ZnO hybrid nanocomposites exhibited complete removal of COD for ibuprofen, ceftriaxone pharmaceuticals and 2.4.5 trichloro phenoxy acetic acid pesticide after 2 h with no selectivity. Briefly, 3% CuS QDs@ZnO hybrid nanocomposites can be considered as promising photoactive materials under simulated sunlight for wastewater decontamination.

Potential of Fluoride-Containing Zinc Oxide and Copper Oxide Nanocomposites on Dentin Bonding Ability

Despite recent advances in bonding restorations, which are the basis of restorative dentistry, secondary caries are still able to form. Previously, a novel fluoride-containing zinc and copper (ZCF) nanocomposite was introduced to prevent the formation of caries due to its antibacterial activity. In this study, we studied the impact of ZCF nanoparticles on the adhesive strength of bonding restorations through micro-tensile bond strength (µTBS) testing. The impact of antibacterial and matrix metalloproteinase (MMP) inhibitors on the nanoparticles was also examined. The nanocomposites were prepared using a simple one-step homogeneous co-precipitation method at a low temperature. A self-etch adhesive was applied to 10 extracted caries-free human molars with (test group) and without (control group) the ZCF nanoparticles. This was followed by composite resin build-up and µTBS testing, MMP activity assays, and evaluation of the antibacterial effects. The results showed no significant differences in the µTBS between the ZCF and the control groups. However, the ZCF exhibited a significant inhibitory effect against MMP-2, MMP-8, and MMP-9, in addition to an antibacterial effect on Streptococcus mutans. Therefore, the present study demonstrated that the addition of ZCF nanoparticles to adhesive systems can result in MMP inhibition and antibacterial action while maintaining the mechanical properties of the bonding restorations.

Nanophotocatalysis for the Removal of Pharmaceutical Residues from Water Bodies: State of Art and Recent Trends

Background:

The occurrence of pharmaceuticals in surface and drinking water is ubiquitous and is a major concern of researchers. These compounds cause a destructive impact on aquatic and terrestrial life forms, and the removal of these compounds from the environment is a challenging issue. Existent conventional wastewater treatment processes are generally inefficacious because of their low degradation efficiency and inadequate techniques associated with the disposal of adsorbed pollutants during comparatively effective methods like the adsorption process.

Remediation Method:

Semiconductor-mediated photocatalysis is an attractive technology for the efficient removal of pharmaceutical compounds. Among various semiconductors, TiO2 and ZnObased photocatalysts gained much interest during the last years because of their efficiency in decomposing and mineralizing the lethal organic pollutants with the utilization of UV-visible light. Incessant efforts are being undertaken for tuning the physicochemical, optical, and electronic properties of these photocatalysts to strengthen their overall photocatalytic performance with good recycling efficiency.

Results:

This review attempts to showcase the recent progress in the rational design and fabrication of nanosized TiO2 and ZnO photocatalysts for the removal of pollutants derived from the pharmaceutical industry and hospital wastes.

Conclusion:

Photocatalysis involving TiO2 and ZnO provides a positive impact on pollution management and could be successfully applied to remove pharmaceuticals from wastewater streams. Structure modifications, the introduction of heteroatoms, and the integration of polymers with these nano photocatalysts offer leapfrogging opportunities for broader applications in the field of photocatalysis.

Visible-Light-Driven Bio-Templated Magnetic Copper Oxide Composite for Heterogeneous Photo-Fenton Degradation of Tetracycline

The development of a visible-light-driven, reusable, and long-lasting catalyst for the heterogeneous photo-Fenton process is critical for practical application in the treatment of contaminated water. This study focuses on synthesizing a visible-light-driven heterogenous bio-templated magnetic copper oxide composite (Fe3O4/CuO/C) by a two-step process of bio-templating and hydrothermal processes. The prepared composite was characterized by field emission-scanning electron microscope (FE-SEM), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), electrical impedance spectroscopy (EIS), and vibrating sample magnetometer (VSM). The results reveal that the prepared composite retains the template’s (corn stalk’s) original porous morphology, and a substantial amount of CuO and Fe3O4 particles are loaded onto the surface of the template. The prepared Fe3O4/CuO/C composite was employed as a catalyst for heterogeneous photo-Fenton degradation of tetracycline (TC) irradiated by visible light. The prepared Fe3O4/CuO/C catalyst has high efficiency towards TC degradation within 60 min across a wide pH range irradiated by visible light, which is attributed to its readily available interfacial boundaries, which significantly improves the movement of photoexcited electrons across various components of the prepared composite. The influence of other parameters such as initial H2O2 concentration, initial concentration of TC, and catalyst dosages was also studied. In addition to high efficiency, the prepared catalyst’s performance was sustained after five cycles, and its recovery is aided by the use of an external magnetic field. This research paper highlights the development of a heterogeneous catalyst for the elimination of refractory organic compounds in wastewater.

Enhanced activated persulfate oxidation of ciprofloxacin using a low-grade titanium ore under sunlight: influence of the irradiation source on its transformation products

In this work, the activated persulfate oxidation of ciprofloxacin (CIP) using a low-grade titanium ore under sunlight or simulated sunlight were conducted to analyze the CIP degradation efficiency and to identify the transformation products (TPs) generated during oxidation under both types of irradiation sources by using liquid chromatography-quadrupole time-of-flight mass spectrometry (LC-QTOF-MS). All advance oxidation process experiments were performed in a 2700-mL raceway reactor at a pH value of ~ 6.5 and an initial CIP concentration of 1 mg/L, during 90 min of reaction time. The control experiments carried out under simulated sunlight achieved a 97.7 ± 0.6% degradation efficiency, using 385 W/m² of irradiation with an average temperature increase of 11.7 ± 0.6 °C. While, the experiments under sunlight reached a 91.2 ± 1.3% degradation efficiency, under an average irradiation value of 19.2 ± 0.3 W/m² in October-November 2019 at hours between 11:00 am and 3:00 pm with an average temperature increase of 1.4 ± 0.8 °C. Mass spectrometry results indicated that 14 of the 108 possible TPs reported in the literature were detected. The calculated exact mass, measured accurate mass, and its characteristic diagnostic fragment ions were listed, and two new TPs were tentative identified. The TP generation analysis showed that some specific compounds were detected in different time intervals with kinetic variations depending on the irradiation used. Consequently, two CIP degradation pathways were proposed, since the type of irradiation determines the CIP degradation mechanism. Graphical abstract.

Review on the Visible Light Photocatalysis for the Decomposition of Ciprofloxacin, Norfloxacin, Tetracyclines, and Sulfonamides Antibiotics in Wastewater

Antibiotics are chemical compounds that are used to kill or prevent bacterial growth. They are used in different fields, such as the medical field, agriculture, and veterinary. Antibiotics end up in wastewater, which causes the threat of developing antibacterial resistance; therefore, antibiotics must be eliminated from wastewater. Different conventional elimination methods are limited due to their high cost and effort, or incomplete elimination. Semiconductor-assisted photocatalysis arises as an effective elimination method for different organic wastes including antibiotics. A variety of semiconducting materials were tested to eliminate antibiotics from wastewater; nevertheless, research is still ongoing due to some limitations. This review summarizes the recent studies regarding semiconducting material modifications for antibiotic degradation using visible light irradiation.

Removal of Emerging Pollutants from Water Using Environmentally Friendly Processes: Photocatalysts Preparation, Characterization, Intermediates Identification and Toxicity Assessment

Pharmaceuticals and pesticides are emerging contaminants problematic in the aquatic environment because of their adverse effects on aquatic life and humans. In order to remove them from water, photocatalysis is one of the most modern technologies to be used. First, newly synthesized photocatalysts were successfully prepared using a sol-gel method and characterized by different techniques (XRD, FTIR, UV/Vis, BET and SEM/EDX). The photocatalytic properties of TiO₂, ZnO and MgO nanoparticles were examined according to their removal from water for two antibiotics (ciprofloxacin and ceftriaxone) and two herbicides (tembotrione and fluroxypyr) exposed to UV/simulated sunlight (SS). TiO₂ proved to be the most efficient nanopowder under UV and SS. Addition of (NH₄)₂S₂O₈ led to the faster removal of both antibiotics and herbicide fluroxypyr. The main intermediates were separated and identified for the herbicides and antibiotic ciprofloxacin. Finally, the toxicity of each emerging pollutant mixture and formed intermediates was assessed on wheat germination and biomass production.

Copper and sulphur co-doped titanium oxide nanoparticles with enhanced catalytic and photocatalytic properties

Copper and sulphur co-doped titanium oxide nanoparticles have been prepared by the sol–gel method to develop versatile catalysts exhibiting enhanced catalytic and photocatalytic properties.

Facile fabrication of highly flexible and floatable Cu2O/rGO on Vietnamese traditional paper toward high-performance solar-light-driven photocatalytic degradation of ciprofloxacin antibiotic

In this work, we successfully demonstrated the facile fabrication of highly flexible and floatable Cu₂O/rGO on Vietnamese traditional paper (VTP) for the solar-light-driven photocatalytic degradation of the antibiotic ciprofloxacin. The catalyst membrane was prepared by the green reduction of both Cu(OH)₂ to Cu₂O nanoparticles and graphene oxide to reduced graphene oxide. VTP has a fibrous structure with tiny fibers connected like a spider web and multiple layers in the form of a multidimensional array, which functions as a flexible and highly porous supporter to the catalyst. Moreover, the microfibrillated cellulose of VTP acts as micro-capillaries to drag ciprofloxacin (CIP) close to the active sites on the Cu₂O/rGO/VTP surface, which improves the adsorption capacity and photocatalytic efficiency of ciprofloxacin. The adsorption process is best described by the pseudo-first-order and Freundlich models. The maximum photodegradation of CIP by the catalyst is more than 80% attained after 1.5 h under solar light irradiation with a fixed CIP concentration of 10 mg L⁻¹. The catalyst membrane exhibited good reusability of up to 5 cycles.

In this work, we successfully demonstrated the facile fabrication of highly flexible and floatable Cu₂O/rGO on Vietnamese traditional paper (VTP) for the solar-light-driven photocatalytic degradation of the antibiotic ciprofloxacin.

MoS2 nanosheet incorporated α-Fe2O3/ZnO nanocomposite with enhanced photocatalytic dye degradation and hydrogen production ability

We have synthesized MoS₂ incorporated α-Fe₂O₃/ZnO nanocomposites by adapting a facile hydrothermal synthesis process. The effect of incorporating ultrasonically exfoliated few-layer MoS₂ nanosheets on the solar-light driven photocatalytic performance of α-Fe₂O₃/ZnO photocatalyst nanocomposites has been demonstrated. Structural, morphological and optical characteristics of the as-synthesized nanomaterials are comprehensively investigated and analyzed by performing Rietveld refinement of powder X-ray diffraction patterns, field emission scanning electron microscopy and UV-visible spectroscopy, respectively. The photoluminescence spectra of the as-prepared nanocomposites elucidate that the recombination of photogenerated electron–hole pairs is highly suppressed due to incorporation of MoS₂ nanosheets. Notably, the ultrasonicated MoS₂ incorporated α-Fe₂O₃/ZnO nanocomposite manifests 91% and 83% efficiency in degradation of rhodamine B dye and antibiotic ciprofloxacin respectively under solar illumination. Active species trapping experiments reveal that the hydroxyl (˙OH) radicals play a significant role in RhB degradation. Likewise the dye degradation efficiency, the amount of hydrogen produced by this nanocomposite via photocatalytic water splitting is also considerably higher as compared to both non-ultrasonicated MoS₂ incorporated α-Fe₂O₃/ZnO and α-Fe₂O₃/ZnO nanocomposites as well as Degussa P25 titania nanoparticles. This indicates the promising potential of the incorporation of ultrasonicated MoS₂ with α-Fe₂O₃/ZnO nanocomposites for the generation of carbon-free hydrogen by water splitting. The substantial increase in the photocatalytic efficiency of α-Fe₂O₃/ZnO after incorporation of ultrasonicated MoS₂ can be attributed to its favorable band structure, large surface to volume ratio, effective segregation and migration of photogenerated electron–hole pairs at the interface of heterojunctions and the plethora of exposed active edge sites provided by the few-layer MoS₂ nanosheets.

Novel few-layer MoS₂ nanosheets incorporated α-Fe₂O₃/ZnO photocatalyst nanocomposite is reported with high dye degradation and hydrogen evolution ability under solar illumination.