Comparison of the Friction and Wear Characteristics between Copper and Paper Based Friction Materials

Influence of the Additive of Ceramic and Intermetallic Powders on the Friction Properties and Temperature of the Wet Clutch Disc

The basic function of friction clutches is to transfer the torque in the conditions of its smooth engagement without vibrations. Hard working conditions under high thermal and mechanical loads, leading to high temperature in the contact area, intense wear, and instability of the coefficient of friction impose restrictive criteria in the design of friction materials. In this paper, the results of experimental research of the effect of ceramic and intermetallic additives to the copper-based material of the friction disc of the clutch on the thermophysical and frictional properties were presented. Next, these properties were incorporated in the proposed contact 3D numerical model of the clutch to carry out computer simulations of the heating process and subsequent cooling. Based on the obtained experimental data and transient temperature changes of the friction and steel discs, the relations between the powder additives, thermophysical properties of the five friction materials, and coefficients of friction, wear, and temperature reached were discussed. Among these, it was found that when working with the lubrication, the largest values of the coefficient of friction 0.068 and wear 13.5  μm  km−1 were reached when using the 3 wt.% SiC additive.

Friction-Wear Characteristics of Carbon Fiber Reinforced Paper-Based Friction Materials under Different Working Conditions

To study the friction and wear performance of carbon fiber reinforced friction materials under different working conditions, paper-based friction materials with different fibers were prepared. Experiments on the SAE#2 test bench were conducted to study the infectors including friction torques, surface temperature, coefficient of friction (COF), and surface morphologies. The results were analyzed, which indicated that the carbon fiber reinforced friction material could provide a higher friction torque and a lower temperature rising rate under the applied high pressure and high rotating speed conditions. As the pressure increased from 1 MPa to 2.5 MPa, the friction torque of plant fiber reinforced material increased by 150%, the friction torque of carbon fiber reinforced material increased by 400%, and the maximum temperature of plant fiber reinforced and carbon fiber reinforced material reached the highest value at 1.5 MPa. Thus, carbon fibers not only improved the COF and friction torque performance but also had advantages in avoiding thermal failure. Meanwhile, carbon fiber reinforced friction materials can provide a more stable COF as its variable coefficient (α) only rose from 38.18 to 264.62, from 1 MPa to 2.5 MPa, which was much lower than the natural fiber reinforced friction materials. Simultaneously, due to the good dispersion and excellent mechanical properties of PAN chopped carbon fibers, fewer pores formed on the initial surface, which improved the high wear resistance, especially in the intermedia disc.

Effect of Silicon Carbide Nanoparticles on the Friction-Wear Properties of Copper-Based Friction Discs

To study the influence of nano-additives on the friction-wear characteristics of friction materials, the nano-sized silicon carbide particles which have excellent chemical and physical properties are considered to add in composite to form the modified friction material. The influence of the silicon carbide nanoparticles (SCN) on the friction-wear characteristics of copper-based friction materials (CBFM) is investigated via the SAE#2 (made in Hangzhou, China) clutch bench test with the applied pressure, rotating speed, and automatic transmission fluid (ATF) temperature taken into account. Moreover, the variations of friction torque and temperature are considered to evaluate the friction performance, and the variable coefficient is employed to describe the friction stability. The wear characteristics of friction materials are investigated by the disc changes in thickness and micro-morphology. The results show that the CBFM with SCN can provide a higher friction torque, which increased by 30% to 50% compared with CBFM. The variable coefficient of CBFM with SCN changes from 674 to 52 with the rotating speed raised from 600 rpm to 3000 rpm, which shows that the friction stability is relatively worse. Furthermore, the micromorphology shows that the CBFM with SCN has lower porosity and surface roughness, which increases the microscopic contact area and the coefficient of friction (COF). Simultaneously, the reduction in porosity also leads to a decrease in the cooling quality, bringing about a rapid temperature rise. Thus, the wear amount of CBFM with SCN increases significantly, especially for the friction disc in the axial middle position.

An Effect of a Carbon-Containing Additive in the Structure of a Friction Material on Temperature of the Wet Clutch Disc

This paper consists of two parts. The first one contains a description and methodology of the composite material used as friction material in clutches. Four variants of such material, differing in the type of carbon additive (the elemental graphite, pencil graphite and foundry coke powder of various fractions) were considered. Thermal conductivity, thermal diffusivity as well as the specific heat all materials were determined experimentally. On the inertial IM-58 stand, a simulation of the braking process of the friction pair consisting of a steel disc with friction material and a counterpart in the form of a homogeneous steel disc was carried out. On this basis, averaged coefficients of friction, unchanging in the entire sliding process, were found for the four friction pairs. The experimental data obtained in the first stage were used in the second stage to develop two (2D and 3D) numerical models of the friction heating process of the friction pairs under consideration. For four variants of the friction material, a comparative spatial-temporal temperature analysis was performed using both models. It was found that a simplified axisymmetric (2D) model can be used to estimate the maximum temperature with high accuracy. The lowest maximum temperature (115.6 °C) obtained for the same total friction work was achieved on the friction surface of the material with the addition of GP-1.

Influence of Material Parameters on the Contact Pressure Characteristics of a Multi-Disc Clutch

As an essential part of the transmission, the life of the clutch directly affects the stability of the transmission. In this paper, a finite element model and a thermodynamic numerical model of a multi-disc clutch are established to investigate the influence of material parameters on the contact pressure distribution. The pressure distribution index (PDI) is firstly proposed to evaluate the pressure difference among friction pairs. Moreover, the correctness of the numerical model is verified by the clutch static pressure experiment. The results show that increasing the elastic modulus and Poisson’s ratio of the backplate can effectively improve the uniformity of the contact pressure. However, the variations in material parameters of other clutch components can not easily smooth the pressure difference. Therefore, optimized material parameters for the clutch are proposed, where the maximum pressure and temperature differences are reduced by about 27.2% and 10.3%, respectively.

Numerical and Experimental Studies of the Attenuation Characteristics of Friction Torque in a Wet Multidisc Clutch

A numerical model is proposed to calculate both the contact pressure and the friction torque (FT) of the friction components considering the spline friction in a wet multidisc clutch, which is verified by the bench test. The results indicate that the spline friction of components is an important factor causing the axial attenuation of contact pressure on friction pairs. As the applied pressure increases, the attenuation amplitude of contact pressure increases gradually. In addition, the average single-pair FT decreases with the increasing number of friction pairs, thus leading to the decrease of the growth rate of total FT. Therefore, when the number of friction pairs reaches a certain number, it is not reliable to obtain a good torque enhancement, indicating that the effect of spline friction needs to be weakened to reduce the attenuation of contact pressure.