On the Dependence of Rheology of Hyaluronic Acid Solutions and Frictional Behavior of Articular Cartilage

Multimodal mechano-microscopy reveals mechanical phenotypes of breast cancer spheroids in three dimensions

Cancer cell invasion relies on an equilibrium between cell deformability and the biophysical constraints imposed by the extracellular matrix (ECM). However, there is little consensus on the nature of the local biomechanical alterations in cancer cell dissemination in the context of three-dimensional (3D) tumor microenvironments (TMEs). While the shortcomings of two-dimensional (2D) models in replicating in situ cell behavior are well known, 3D TME models remain underutilized because contemporary mechanical quantification tools are limited to surface measurements. Here, we overcome this major challenge by quantifying local mechanics of cancer cell spheroids in 3D TMEs. We achieve this using multimodal mechano-microscopy, integrating optical coherence microscopy-based elasticity imaging with confocal fluorescence microscopy. We observe that non-metastatic cancer spheroids show no invasion while showing increased peripheral cell elasticity in both stiff and soft environments. Metastatic cancer spheroids, however, show ECM-mediated softening in a stiff microenvironment and, in a soft environment, initiate cell invasion with peripheral softening associated with early metastatic dissemination. This exemplar of live-cell 3D mechanotyping supports that invasion increases cell deformability in a 3D context, illustrating the power of multimodal mechano-microscopy for quantitative mechanobiology in situ.

Size Matters: Rethinking Hertz Model Interpretation for Cell Mechanics Using AFM

Cell mechanics are a biophysical indicator of cell state, such as cancer metastasis, leukocyte activation, and cell cycle progression. Atomic force microscopy (AFM) is a widely used technique to measure cell mechanics, where the Young modulus of a cell is usually derived from the Hertz contact model. However, the Hertz model assumes that the cell is an elastic, isotropic, and homogeneous material and that the indentation is small compared to the cell size. These assumptions neglect the effects of the cytoskeleton, cell size and shape, and cell environment on cell deformation. In this study, we investigated the influence of cell size on the estimated Young's modulus using liposomes as cell models. Liposomes were prepared with different sizes and filled with phosphate buffered saline (PBS) or hyaluronic acid (HA) to mimic the cytoplasm. AFM was used to obtain the force indentation curves and fit them to the Hertz model. We found that the larger the liposome, the lower the estimated Young's modulus for both PBS-filled and HA-filled liposomes. This suggests that the Young modulus obtained from the Hertz model is not only a property of the cell material but also depends on the cell dimensions. Therefore, when comparing or interpreting cell mechanics using the Hertz model, it is essential to account for cell size.

A Low Transition Temperature Mixture-based viscosupplementation complemented with celecoxib for osteoarthritis treatment

Viscosupplementation consists of hyaluronic acid (HA) intra-articular injections, commonly applied for osteoarthritis treatment while non-steroidal anti-inflammatory drugs (NSAIDs) are widely administered for pain relief. Here, HA and a NSAID (celecoxib) were combined in a formulation based on a low transition temperature mixture (LTTM) of glycerol:sorbitol, reported to increase celecoxib's solubility, thus rendering a potential alternative viscosupplement envisioning enhanced therapeutic efficiency. The inclusion of glucosamine, a cartilage precursor, was also studied. The developed formulations were assessed in terms of rheological properties, crucial for viscosupplementation: the parameters of crossover frequency, storage (G') and loss (G'') moduli, zero-shear-rate viscosity, stable viscosity across temperatures, and shear thinning behaviour, support viscoelastic properties suitable for viscosupplementation. Additionally, the gels biocompatibility was confirmed in chondrogenic cells (ATDC5). Regarding drug release studies, high and low clearance scenarios demonstrated an increased celecoxib (CEX) release from the gel (6 to 73-fold), compared to dissolution in PBS. The low clearance setup presented the highest and most sustained CEX release, highlighting the importance of the gel structure in CEX delivery. NMR stability studies over time demonstrated the LTTM+HA+CEX (GHA+CEX) gel as viable candidate for further in vivo evaluation. In sum, the features of GHA+CEX support its potential use as alternative viscosupplement.

In vitro drug release and cartilage interface lubrication properties of biomimetic polymers

Osteoarthritis is a degenerative disease that is widely found in the elderly population, with a trend towards a younger age group in recent years. In the early stages of arthritis, patients are treated with hyaluronic acid injections and anti-inflammatory drugs. However, it has been found that hyaluronic acid can only play a supportive role and does not have a lubricating effect, and due to the absence of blood vessels, nerves, and lymphatic vessels in the articular cartilage, the oral anti-inflammatory drugs cannot reach the interface of the inflammatory joints adequately, and the drug utilisation rate is low. Herein, we designed and prepared a brush-like bionic lubricant for joint lubrication and drug loading. The poly(2-methyl-2-oxazoline) branched chain was grafted onto the hyaluronic acid main chain by ring-opening polymerisation and graft polymerisation to form a brush-like bionic lubricin containing multiple hydrophilic groups, which was self-assembled to encapsulate the drug by using its multi-branched special structure for drug loading. The friction behaviour tests on the articular cartilage surface showed that the prepared bionic lubricin has excellent lubrication effect, with a minimum friction coefficient of 0.036 close to the lubrication effect of natural synovial fluid, which is mainly due to the hydrophilic groups on its molecular chain that can adsorb the water molecules and form a hydration layer at the cartilage interface, which plays the role of hydration lubrication. In addition, in vitro drug release studies showed that the synthesised drug-loading biomimetic lubricin had a certain drug release capacity, and the maximum drug release rate could reach 77.8 % at 72 h. The synthesis of this bionic lubricant with dual functions of lubrication and drug release provides a new idea for the treatment of osteoarthritis.

Preparation and characterization of a novel composite acellular matrix/hyaluronic acid thermosensitive hydrogel for interstitial cystitis/bladder pain syndrome

Bladder mucosa damage that causes harm to the interstitium is a recognized pathogenesis of interstitial cystitis/bladder pain syndrome (IC/BPS). The intravesical instillation of drugs is an important second-line therapy, but it is often necessary to use drugs repeatedly in the clinic because of their short residence time in the bladder cavity, which alters the therapeutic effect. To overcome this drawback, this study developed a novel composite acellular matrix/hyaluronic acid (HA) thermosensitive hydrogel (HA-Gel) using rabbit small intestinal submucosa extracellular matrix (ECM) as the thermosensitive material and HA as the drug component and examined its composition, microstructure, thermodynamic properties, temperature sensitivity, rheological properties, biocompatibility, drug release, hydrogel residue, and bacteriostatic properties. The study showed HA-Gel was liquid at temperatures of 15-37.5°C and solid at 37.5-50°C, its swelling rate decreased with increasing temperature, and its lower critical solution temperature occurred at approximately 37.5°C. This property made the hydrogel liquid at room temperature convenient for intravesical perfusion and turned into a solid about 1 min after entering the body and rising to body temperature to increase its residence time. Subsequent experiments also proved that the gel residue time of HA-Gel in vivo and the drug release time of HA in vivo could reach more than 5 days, which was significantly higher than that of HA alone, and it had good biocompatibility and antibacterial properties. Therefore, this hydrogel possesses the proper characteristics to possibly make it an ideal dosage form for IC/BPS intravesical instillation therapy.

Cartilage regeneration using transforming growth factor-beta 3-loaded injectable crosslinked hyaluronic acid hydrogel

Cartilage defects can be difficult to heal, potentially leading to complications such as osteoarthritis. Recently, a tissue engineering approach that uses scaffolds and growth factors has been proposed to regenerate new cartilage tissues. Herein, we investigated the application of hyaluronic acid (HA) gel loaded with transforming growth factor-beta 3 (TGF-β3) for enhanced cartilage regeneration. We assessed the clinical conditions required to efficiently enhance the ability of the modified HA gel to repair defective cartilage. Based on our findings, the prepared HA gel exhibited good physicochemical and mechanical properties and was non-toxic and non-inflammatory. Moreover, HA gel-loaded TGF-β3 (HAT) had improved biocompatibility and promoted the synthesis of cartilage-specific matrix and collagen, further improving its ability to repair defects. The application of HAT resulted in an initial burst release of HA, which degraded slowly in vivo. Finally, HAT combined with microfracture-inducing bone marrow stem cells could significantly improve the cartilage microenvironment and regeneration of cartilage defects. Our results indicate that HA is a suitable material for developing growth factor carriers, whereas HAT is a promising candidate for cartilage regeneration. Furthermore, this differentiated strategy provides a rapid and effective clinical approach for next-generation cartilage regeneration.

Hyaluronic acid single-network hydrogel with high stretchable and elastic properties

Stretchable materials have demonstrated great interest in wearable or implantable applications. Most of the existing hydrogels with high stretchability characteristics are based on double networks, exhibit large hysteresis loops, and cannot recover after deformation due to permanent rupture of network. Elastic, biodegradable, and biocompatible hydrogels are desirable for wound dressing of joints with frequent motions or post-surgical healing of mobile tissues. Here, we show a simple strategy for the preparation of a hyaluronic acid (HA) single-network hydrogel that can be stretchable and highly elastic without the addition of other components/partners or complicated processes of preparation. Our strategy relies on the use of high Mw HA to create a chemical hydrogel in which densely entangled HA chains are tied together by a small number of covalent bonds. While the presence of covalent cross-links can prevent disintegration of the HA network, entanglements endow the hydrogel with high stretchability through transmission of tension along the length of the long HA chains. The stretching-relaxation cycles show negligible hysteresis and perfect recovery of material after the release of force. The diminution of Mw together with increasing the concentration or cross-linker amount leads to brittle hydrogels.

Boron Nitride's Morphological Role in the Design of Injectable Hyaluronic Acid Based Hybrid Artificial Synovial Fluid

The treatment process of osteoarthritis (OA) is challenging as it affects not only cartilage but also subchondral bone, ligament attachment capsules, synovium, and surrounding muscle tissue. Therefore, the search for preventive treatment or methods to slow the onset of the condition. Hexagonal boron nitride (hBN) has a graphite-like lamellar structure and is thought to facilitate cartilage movement for biomedical applications, just like in bearing systems. Hyaluronic acid (HA) is one of the natural polymers that can be used to transport boron nitride and maintain its presence in joints for a long time. In this study, hybrid hydrogels were formulated by using boron nitride nanoparticles and nanosheets. The rheological properties of the hydrogels were evaluated according to the structural differences of hBN. Characterizations have shown that hybrid hydrogels can be produced in injectable form, and the rheological properties are strongly related to the structural properties of the added particle. It has been determined that hBN added to the hydrogel structure reduces the dynamic viscosity of the zero-shear point and the deformation rate of the hydrogel and also changes the viscoelastic properties of the hydrogel depending on boron nitride's structural differences. The suggested mechanism is the hybrid hydrogel that exhibits lower viscosity as the layers detach from each other or disperses the agglomerates under applied shear stress. hBN, which has been proposed as a new strategy for joint injections, is thought to be a promising candidate for the treatment of OA due to its lamellar structures.

Ex Vivo Functional Benchmarking of Hyaluronan-Based Osteoarthritis Viscosupplement Products: Comprehensive Assessment of Rheological, Lubricative, Adhesive, and Stability Attributes

While many injectable viscosupplementation products are available for osteoarthritis (OA) management, multiple hydrogel functional attributes may be further optimized for efficacy enhancement. The objective of this study was to functionally benchmark four commercially available hyaluronan-based viscosupplements (Ostenil, Ostenil Plus, Synvisc, and Innoryos), focusing on critical (rheological, lubricative, adhesive, and stability) attributes. Therefore, in vitro and ex vivo quantitative characterization panels (oscillatory rheology, rotational tribology, and texture analysis with bovine cartilage) were used for hydrogel product functional benchmarking, using equine synovial fluid as a biological control. Specifically, the retained experimental methodology enabled the authors to robustly assess and discuss various functional enhancement options for hyaluronan-based hydrogels (chemical cross-linking and addition of antioxidant stabilizing agents). The results showed that the Innoryos product, a niacinamide-augmented linear hyaluronan-based hydrogel, presented the best overall functional behavior in the retained experimental settings (high adhesivity and lubricity and substantial resistance to oxidative degradation). The Ostenil product was conversely shown to present less desirable functional properties for viscosupplementation compared to the other investigated products. Generally, this study confirmed the high importance of formulation development and control methodology optimization, aiming for the enhancement of novel OA-targeting product critical functional attributes and the probability of their clinical success. Overall, this work confirmed the tangible need for a comprehensive approach to hyaluronan-based viscosupplementation product functional benchmarking (product development and product selection by orthopedists) to maximize the chances of effective clinical OA management.

The Combination of Glucocorticoids and Hyaluronic Acid Enhances Efficacy in IL-1β/IL-17-Treated Bovine Osteochondral Grafts Compared with Individual Application

Patients with knee osteoarthritis often receive glucocorticoid (GC) or hyaluronic acid (HA) injections to alleviate symptoms. This study evaluated the impact of Triamcinolone Hexacetonide (a GC), HA, and a combination of both on bovine osteochondral grafts exposed to IL-1β and IL-17 in an ex vivo culture. Metabolic activity increased with GC treatment. GCs and GCs/HA counteracted cytokine effects, with gene expressions similar to untreated controls, while HA alone did not. However, HA improved the coefficient of friction after two weeks. The highest friction values were observed in GC-containing and cytokine-treated groups. Cytokine treatment reduced tissue proteoglycan content, which HA could mitigate, especially in the GC/HA combination. This combo also effectively controlled proteoglycan release, supported by reduced sGAG release. Cytokine treatment led to surface cell death, while GCs, HA, or their combination showed protective effects against inflammation. The GC/HA combination had the best overall results, suggesting its potential as a superior treatment option for osteoarthritis.

Comparison of Four Treatment Protocols with Intra-Articular Medium Molecular Weight Hyaluronic Acid in Induced Temporomandibular Osteoarthritis: An Experimental Study

The aim was to compare the effect between a single intra-articular infiltration (1i) and two infiltrations (2i) of medium molecular weight hyaluronic acid (MMW-HA) of high viscosity (HV) and low viscosity (LV) on the histopathological characteristics of temporomandibular joint (TMJ) osteoarthritis (OA) induced in rabbits. An experimental study was conducted on Oryctolagus cuniculus rabbits, including 42 TMJs, distributed between (1) TMJ-C, control group; (2) TMJ-OA, group with OA; (3) TMJ-OA-wt, group with untreated OA; (4) group treated with HA-HV-1i; (5) group treated with HA-HV-2i; (6) group treated with HA-LV-1i; and (7) group treated with HA-LV-2i. The results were evaluated using the Osteoarthritis Research Society International (OARSI) scale and descriptive histology considering the mandibular condyle (MC), the articular disc (AD), and the mandibular fossa (MF). The Kruskal-Wallis test was used for the statistical analysis, considering p < 0.05 significant. All treated groups significantly decreased the severity of OA compared to the TMJ-OA-wt group. The HA-HV-2i group showed significant differences in the degree of OA from the TMJ-OA group. The degree of OA in the HA-HV-2i group was significantly lower than in the HA-LV-1i, HA-LV-2i, and HA-HV-1i groups. The protocol that showed better results in repairing the joint was HA-HV-2i. There are histological differences depending on the protocol of the preparation used: two infiltrations seem to be better than one, and when applying two doses, high viscosity shows better results.

Rheological Considerations of Pharmaceutical Formulations: Focus on Viscoelasticity

Controlling rheological properties offers the opportunity to gain insight into the physical characteristics, structure, stability and drug release rate of formulations. To better understand the physical properties of hydrogels, not only rotational but also oscillatory experiments should be performed. Viscoelastic properties, including elastic and viscous properties, are measured using oscillatory rheology. The gel strength and elasticity of hydrogels are of great importance for pharmaceutical development as the application of viscoelastic preparations has considerably expanded in recent decades. Viscosupplementation, ophthalmic surgery and tissue engineering are just a few examples from the wide range of possible applications of viscoelastic hydrogels. Hyaluronic acid, alginate, gellan gum, pectin and chitosan are remarkable representatives of gelling agents that attract great attention applied in biomedical fields. This review provides a brief summary of rheological properties, highlighting the viscoelasticity of hydrogels with great potential in biomedicine.

Visualizable and Lubricating Hydrogel Microspheres Via NanoPOSS for Cartilage Regeneration

The monitoring of tissue regeneration is particularly important. However, most materials do not allow direct observation of the regeneration process in the cartilage layer. Here, using sulfhydryl polyhedral oligomeric silsesquioxane (POSS-SH) as a nano-construction platform, poly(ethylene glycol) (PEG), Kartogenin (KGN), hydrogenated soya phosphatidylcholine (HSPC), and fluorescein are linked through the "click chemistry" method to construct nanomaterial with fluorescence visualization for cartilage repair: POSS linked with PEG, KGN, HSPC, and fluorescein (PPKHF). PPKHF nanoparticles are encapsulated with hyaluronic acid methacryloyl to prepare PPKHF-loaded microfluidic hyaluronic acid methacrylate spheres (MHS@PPKHF) for in situ injection into the joint cavity using microfluidic technology. MHS@PPKHF forms a buffer lubricant layer in the joint space to reduce friction between articular cartilages, while releasing encapsulated positively charged PPKHF to the deep cartilage through electromagnetic force, facilitating visualization of the location of the drug via fluorescence. Moreover, PPKHF facilitates differentiation of bone marrow mesenchymal stem cells into chondrocytes, which are located in the subchondral bone. In animal experiment, the material accelerates cartilage regeneration while allowing monitoring of cartilage layer repair progression via fluorescence signals. Thus, these POSS-based micro-nano hydrogel microspheres can be used for cartilage regeneration and monitoring and potentially for clinical osteoarthritis therapy.

Structures, Properties, and Bioengineering Applications of Alginates and Hyaluronic Acid

In recent years, polymeric materials have been used in a wide range of applications in a variety of fields. In particular, in the field of bioengineering, the use of natural biomaterials offers a possible new avenue for the development of products with better biocompatibility, biodegradability, and non-toxicity. This paper reviews the structural and physicochemical properties of alginate and hyaluronic acid, as well as the applications of the modified cross-linked derivatives in tissue engineering and drug delivery. This paper summarizes the application of alginate and hyaluronic acid in bone tissue engineering, wound dressings, and drug carriers. We provide some ideas on how to replace or combine alginate-based composites with hyaluronic-acid-based composites in tissue engineering and drug delivery to achieve better eco-economic value.

A composite device for viscosupplementation treatment resistant to degradation by reactive oxygen species and hyaluronidase

Osteoarthritis (OA) is one of the most common musculoskeletal disorders in the world. OA is often associated with the loss of viscoelastic and tribological properties of synovial fluid (SF) due to degradation of hyaluronic acid (HA) by reactive oxygen species (ROS) and hyaluronidases. Viscosupplementation is one of the ways how to effectively restore SF functions. However, current viscosupplementation products provide only temporal therapeutic effect because of short biological half-life. In this article we describe a novel device for viscosupplementation (NV) based on the cross-linked tyramine derivative of HA, chondroitin sulfate (CS), and high molecular weight HA by online determination of viscoelastic properties loss during degradation by ROS and hyaluronidase. Rheological and tribological properties of developed viscosupplement were compared with HA solutions with different molecular weights in the range 500-2000 kDa, which are currently commonly used as medical devices for viscosupplementation treatment. Moreover, based on clinical practice and scientific literature all samples were also diluted by model OA SF in the ratio 1:1 (vol/vol) to better predict final properties after injection to the joint. The observed results confirmed that NV exhibits appropriate rheological properties (viscosity, elastic, and viscous moduli) comparable with healthy SF and maintain them during degradation for a significantly longer time than HA solutions with molecular weight in the range 500-2000 kDa and cross-linked material without CS.

Bioinspired Hydrogels as Platforms for Life-Science Applications: Challenges and Opportunities

Hydrogels, as interconnected networks (polymer mesh; physically, chemically, or dynamic crosslinked networks) incorporating a high amount of water, present structural characteristics similar to soft natural tissue. They enable the diffusion of different molecules (ions, drugs, and grow factors) and have the ability to take over the action of external factors. Their nature provides a wide variety of raw materials and inspiration for functional soft matter obtained by complex mechanisms and hierarchical self-assembly. Over the last decade, many studies focused on developing innovative and high-performance materials, with new or improved functions, by mimicking biological structures at different length scales. Hydrogels with natural or synthetic origin can be engineered as bulk materials, micro- or nanoparticles, patches, membranes, supramolecular pathways, bio-inks, etc. The specific features of hydrogels make them suitable for a wide variety of applications, including tissue engineering scaffolds (repair/regeneration), wound healing, drug delivery carriers, bio-inks, soft robotics, sensors, actuators, catalysis, food safety, and hygiene products. This review is focused on recent advances in the field of bioinspired hydrogels that can serve as platforms for life-science applications. A brief outlook on the actual trends and future directions is also presented.

Cartilage-Inspired Hydrogel with Mechanical Adaptability, Controllable Lubrication, and Inflammation Regulation Abilities

Cartilage is a key component in joints because of its load-bearing and lubricating abilities. However, osteoarthritis often leads to afunction of load-bearing/lubrication and occurrence of inflammation with overexpressed reactive oxygen species (ROS) and nitric oxide (NO). To address these issues, we fabricated a novel polyanionic hydrogel with abundant carboxylates/sulfonates ("CS" hydrogel), inspired by normal cartilage rich in anionic hyaluronate/sulfonate glycosaminoglycan/lubricin, and crosslinked it tightly by Fe3+ ("CS-Fe" hydrogel). The "CS-Fe" hydrogel displayed mechanical adaptability and shear resistance. A low coefficient of friction (∼0.02) appeared when a loose hydrogel layer was generated because of the photoreduction of Fe3+ to Fe2+ by UV irradiation. This biocompatible "CS-Fe" hydrogel suppressed the overexpressed hydroxyl radical (·OH) and NO in macrophages and protected chondrocytes/fibroblasts from aggressive inflammation. Moreover, the layered "CS-Fe" hydrogel avoided cell death of chondrocytes in sliding tests. The results demonstrate that this cartilage-inspired hydrogel is a promising candidate material in cartilage tissue engineering to especially address inflammation.

Sliding Corrosion Fatigue of Metallic Joint Implants: A Comparative Study of CoCrMo and Ti6Al4V in Simulated Synovial Environments

Mechanical contact in a corrosive synovial environment leads to progressive surface damage at the modular interface of the joint implants. The wear debris and corrosion products degrade the synovial fluids and change the lubrication mechanisms at the joints. Consequently, the unstable joint lubrication and corrosion products will further induce the undesirable performance of the joint implants. In this study, the two major joint materials, CoCrMo and Ti6Al4V, were tested during the course of reciprocal sliding contact in simulated synovial liquids. Open circuit potential and coefficient of friction were monitored to describe electrochemical and mechanical responses. Potentiostatic test results illustrated electrochemical damage on both surfaces that modified oxidation chemistry on both surfaces. However, more significant modification of the CoCrMo surface was detected during wear in the simulated joint liquid. Even with a reduced coefficient of friction on the CoCrMo surface in sodium lactate environments, fretting current density drastically increased in corrosive sodium lactate with pH 2. However, the test results from the Ti6Al4V surface presented less coefficient of friction values, and moderate change in fretting current. Therefore, the experimental study concluded that the biocompatibility of Ti6Al4V is superior to that of CoCrMo in the combined effect of mechanical loadings and an electrochemical environment.

Gellan gum modified hyaluronic acid hydrogel as viscosupplement with lubrication maintenance and enzymatic resistance

Osteoarthritis (OA) is a common disease caused by damage to articular cartilage and underlying bone tissues. Early OA can be treated by intra-articular injection of viscosupplements to restore the lost...

RHAMM Is a Multifunctional Protein That Regulates Cancer Progression

The functional complexity of higher organisms is not easily accounted for by the size of their genomes. Rather, complexity appears to be generated by transcriptional, translational, and post-translational mechanisms and tissue organization that produces a context-dependent response of cells to specific stimuli. One property of gene products that likely increases the ability of cells to respond to stimuli with complexity is the multifunctionality of expressed proteins. Receptor for hyaluronan-mediated motility (RHAMM) is an example of a multifunctional protein that controls differential responses of cells in response-to-injury contexts. Here, we trace its evolution into a sensor-transducer of tissue injury signals in higher organisms through the detection of hyaluronan (HA) that accumulates in injured microenvironments. Our goal is to highlight the domain and isoform structures that generate RHAMM's function complexity and model approaches for targeting its key functions to control cancer progression.

Effect of Progressive Resistance Strength Training on Body Mass Index, Quality of Life and Functional Capacity in Knee Osteoarthritis: A Randomized Controlled Trial

Purpose

This study aimed to investigate the effectiveness of progressive resistance strength training of the lower limb rehabilitation protocol (LLRP) on body mass index (BMI), quality of life, and functional capacity in patients with knee osteoarthritis (OA) who were overweight and obese.

Patients and Methods

Fifty-six patients were allocated into either the Rehabilitation Protocol Group (RPG) or the Control Group (CG) by a computer-generated random number. The patients in the RPG performed the strengthening exercises of the LLRP and followed the instruction of daily care (IDC). The patients in the CG only followed the IDC as a usual care. Gait Speed Test, quality of life, and BMI were taken at pre-test and post-test measurements. Paired samples t-test and two way mixed analysis of variance were used to analyze the change of BMI within and compare the difference of BMI between the groups, respectively. Wilcoxon signed ranked test and Mann-Whitney U-test were used to analyze the changes of quality of life and functional capacity within and compare the differences of quality of life and functional capacity between the groups, respectively.

Results

The patients in the RPG reported a significant reduction in BMI (p = 0.025), improvement in quality of life (p ≤ 0.001), and functional capacity (p ≤ 0.001) within group. The patients in the CG also reported a significant improvements in quality of life (p < 0.05). The improvement in quality of life score was greater in the patients with RPG than the CG (p = 0.053).

Conclusion

The progressive resistance strength training of LLRP is effective in terms of reducing BMI, improving quality of life and functional capacity.

Trial Registration

Name: Iranian Registry of Clinical Trials. Number: IRCT20191221045846N3. Enrollment of first participant: 27-07-2020.

Squeeze-film properties of synovial fluid and hyaluronate-based viscosupplements

The rheological properties of synovial fluid and hyaluronate (HA) solutions have been studied using a variety of viscometers and rheometers. These devices measure the viscosity of the fluid's resistance to shearing forces, which is useful when studying the lubrication and frictional properties of movable joints. Less commonly used is a squeeze-film fluid test, mechanistically similar to when two joint surfaces squeeze interposed fluid. In our study, we used squeeze-film tests to determine the rheological response of normal bovine synovial fluid and 10 mg/ml HA-based solutions, Hyalgan/Hyalovet, commercially available 500-700 kDa HA viscosupplements, and a 1000 kDa sodium hyaluronate (NaHy) solution. We found similar rheological responses (fluid thickness, viscosity, viscosity-pressure relationship) for all three fluids, though synovial fluid's minimum squeeze-film thickness was slightly thicker. Squeeze-film loading speed did not affect these results. Different HA concentrations and molecular weights also did not have a significant or consistent effect on the squeeze-film responses. An unexpected result for the HA-solutions was a linear increase in minimum fluid-film thickness with increasing initial fluid-film thickness. This result was attributed to faster gelling of thicker HA-solutions, which formed at a lower squeeze-film strain and higher squeeze-film strain rate compared to thinner layers. Also included is a review of the literature on viscosity measurements of synovial fluid and HA solutions.

Analysis of Chemisorbed Tribo-Film for Ceramic-on-Ceramic Hip Joint Prostheses by Raman Spectroscopy

To understand the possible lubricant mechanism in ceramic-on-ceramic hip joint prostheses, biochemical reactions of the synovial fluid and the corresponding frictional coefficients were studied. The experiments were performed in a hip joint simulator using the ball-on-cup configuration with balls and cups made from two types of ceramics, BIOLOX^®forte and BIOLOX^®delta. Different lubricants, namely albumin, γ-globulin, hyaluronic acid and three model synovial fluids, were studied in the experiments and Raman spectroscopy was used to analyze the biochemical responses of these lubricants at the interface. BIOLOX^®delta surface was found less reactive to proteins and model fluid lubricants. In contrast, BIOLOX^®forte ball surface has shown chemisorption with both proteins, hyaluronic acid and model fluids imitating total joint replacement and osteoarthritic joint. There was no direct correlation between the measured frictional coefficient and the observed chemical reactions. In summary, the study reveals chemistry of lubricant film formation on ceramic hip implant surfaces with various model synovial fluids and their components.

Hyaluronic Acid: The Influence of Molecular Weight on Structural, Physical, Physico-Chemical, and Degradable Properties of Biopolymer

Hyaluronic acid, as a natural linear polysaccharide, has attracted researchers' attention from its initial detection and isolation from tissues in 1934 until the present day. Due to biocompatibility and a high biodegradation of hyaluronic acid, it finds wide application in bioengineering and biomedicine: from biorevitalizing skin cosmetics and endoprostheses of joint fluid to polymeric scaffolds and wound dressings. However, the main properties of aqueous polysaccharide solutions with different molecular weights are different. Moreover, the therapeutic effect of hyaluronic acid-based preparations directly depends on the molecular weight of the biopolymer. The present review collects the information about relations between the molecular weight of hyaluronic acid and its original properties. Particular emphasis is placed on the structural, physical and physico-chemical properties of hyaluronic acid in water solutions, as well as their degradability.