Ni-Rich Layered Oxide with Preferred Orientation (110) Plane as a Stable Cathode Material for High-Energy Lithium-Ion Batteries

LiNi0.6Co0.2Mn0.2O2 Cathode-Solid Electrolyte Interfacial Behavior Characterization Using Novel Method Adopting Microcavity Electrode

Due to the limitations of organic liquid electrolytes, current development is towards high performance all-solid-state lithium batteries (ASSLBs). For high performance ASSLBs, the most crucial is the high ion-conducting solid electrolyte (SE), with a focus on interface analysis between SE and active materials. In the current study, we successfully synthesized the high ion-conductive argyrodite-type (Li₆PS₅Cl) solid electrolyte, which has 4.8 mS cm^-1 conductivity at room temperature. Additionally, the present study suggests the quantitative analysis of interfaces in ASSLBs. The measured initial discharge capacity of a single particle confined in a microcavity electrode was 1.05 nAh for LiNi_0.6Co_0.2Mn_0.2O₂ (NCM622)-Li₆PS₅Cl solid electrolyte materials. The initial cycle result shows the irreversible nature of active material due to the formation of the solid electrolyte interphase (SEI) layer on the surface of the active particle; further second and third cycles demonstrate high reversibility and good stability. Furthermore, the electrochemical kinetic parameters were calculated through the Tafel plot analysis. From the Tafel plot, it is seen that asymmetry increases gradually at high discharge currents and depths, which rise asymmetricity due to the increasing of the conduction barrier. However, the electrochemical parameters confirm the increasing conduction barrier with increased charge transfer resistance.

Advances in the Development of Single-Atom Catalysts for High-Energy-Density Lithium-Sulfur Batteries

Although lithium-sulfur (Li-S) batteries are promising next-generation energy-storage systems, their practical applications are limited by the growth of Li dendrites and lithium polysulfide shuttling. These problems can be mitigated through the use of single-atom catalysts (SACs), which exhibit the advantages of maximal atom utilization efficiency (≈100%) and unique catalytic properties, thus effectively enhancing the performance of electrode materials in energy-storage devices. This review systematically summarizes the recent progress in SACs intended for use in Li-metal anodes, S cathodes, and separators, briefly introducing the operating principles of Li-S batteries, the action mechanisms of the corresponding SACs, and the fundamentals of SACs activity, and then comprehensively describes the main strategies for SACs synthesis. Subsequently, the applications of SACs and the principles of SACs operation in reinforced Li-S batteries as well as other metal-S batteries are individually illustrated, and the major challenges of SACs usage in Li-S batteries as well as future development directions are presented.

Reactivity at the Electrode-Electrolyte Interfaces in Li-Ion and Gel Electrolyte Lithium Batteries for LiNi0.6Mn0.2Co0.2O2 with Different Particle Sizes

The layered oxide LiNi_0.6Mn_0.2Co_0.2O₂ is a very attractive positive electrode material, as shown by the good reversible capacity, chemical stability, and cyclability upon long-range cycling in Li-ion batteries and, hopefully, in the near future, in all-solid-state batteries. Three samples with variable primary particle sizes of 240 nm, 810 nm, and 2.1 μm on average and very similar structures close to the ideal 2D layered structure (less than 2% Ni²⁺ ions in Li⁺ sites) were obtained by coprecipitation followed by a solid-state reaction at high temperatures. The electrochemical performances of the materials were evaluated in a conventional organic liquid electrolyte in Li-ion batteries and in a gel electrolyte in all-solid-state batteries. The positive electrode/electrolyte interface was analyzed by X-ray photoelectron spectroscopy to determine its composition and the extent of degradation of the lithium salt and the carbonate solvents after cycling, taking into account the changes in particle size of the positive electrode material and the nature of the electrolyte.

NAi/Li Antisite Defects in the Li1.2Ni0.2Mn0.6O2 Li-Rich Layered Oxide: A DFT Study

Li-rich layered oxide (LRLO) materials are promising positive-electrode materials for Li-ion batteries. Antisite defects, especially nickel and lithium ions, occur spontaneously in many LRLOs, but their impact on the functional properties in batteries is controversial. Here, we illustrate the analysis of the formation of Li/Ni antisite defects in the layered lattice of the Co-free LRLO Li1.2Mn0.6Ni0.2O2 compound through a combination of density functional theory calculations performed on fully disordered supercells and a thermodynamic model. Our goal was to evaluate the concentration of antisite defects in the trigonal lattice as a function of temperature and shed light on the native disorder in LRLO and how synthesis protocols can promote the antisite defect formation.

Determining the Preferred Orientation of Silver-Plating via X-ray Diffraction Profile

Determining the preferred orientation of plating film is of practical importance. In this work, the Rietveld method and quantitative texture analysis (RM+QTA) are used to analyze the preferred orientation of plating silver film with XRD profile, whose <311> axial texture can be completely described by a set of exponential harmonics index, extracted from a single XRD profile, C41,1(0.609), C61,1(0.278), C81,1(-0.970). The constructed pole figures with the index of the exponential harmonic are following those measured by the multi-axis diffractometer. The method using exponential harmonic index can be extended to characterize the plating by electroplating in a quantitative harmonic description. In addition, a new dimension involving crystallite shape and size is considered in characterizing the preferred orientation.