Finite Element Analysis of the Endodontically-treated Maxillary Premolars restored with Composite Resin along with Glass Fiber Insertion in Various Positions

Stress Distribution of Endodontically Treated Tooth MOD Cavity Restored with Ribbon Fiber-Reinforced Composite (Wallpapering Technique) Using Finite Element Method

Purpose

This research aimed to describe the stress distribution of an endodontically treated tooth with a mesio-occluso-distal (MOD) cavity restored with direct composite reinforced with polyethylene and e-glass ribbon fiber.

Methods

This research was a descriptive study using the finite element method. A 3D model of the mandibular first molar solid after endodontic treatment with class II MOD preparation was prepared using Solidworks software. Finite element simulation was carried out using Abaqus software. In the first simulation, 180 N force was applied (vertically 90° perpendicular to the occlusal surface) at four points of loading: the tip of the mesiobuccal and distobuccal cusp, central fossa, and distal marginal ridge. For the second simulation, a 100 N force was applied at a 45° lateral angle to the occlusal surface at two loading points: the lingual slope of the mesiobuccal and distobuccal cusp.

Results

This study showed that the stress concentration was located in the occlusal pit and fissure, CEJ distal area, bifurcation in dentin, and the 1/3 cervical area of root dentin. The stress value generated after vertical and lateral force did not exceed the tooth and restoration's compressive and tensile strength value. The failure occurred at the interface of enamel and composite near the loading point area due to vertical load, both on polyethylene and e-glass fiber ribbon-reinforced composite restoration. Stress distribution of an endodontically treated tooth with a MOD cavity restored with ribbon fiber-reinforced composite using the finite element method showed that the highest stress concentration occurred on the surface close to the loading point, in narrow, concave, and sharp areas, and more apically for endodontically treated teeth.

Conclusion

Neither the tooth nor restoration failed after vertical and horizontal loads. The interface between enamel and composite on the occlusal surface failed.

Stress Analysis on Mesiolingual Cavity of Endodontically Treated Molar Restored Using Bidirectional Fiber-Reinforced Composite (Wallpapering Technique)

Introduction

Endodontically treated teeth (ETT) undergo extensive structure change and experience high stress during biomechanical function. Stress distribution is influenced by the restoration material and the type of bond between material and tooth structure. The selection of materials that can distribute stress will affect the resistance and retention of ETT to mastication forces, thus biomechanical functions were achieved. Composite has mechanical properties similar to dentin, it can transmit and distribute stresses throughout the tooth surface. The disadvantage of composites in large cavities is their lack of toughness. The addition of fiber to composites can increase their toughness.

Purpose

This research is to determine the stress distribution of a fiber-reinforced composite made of polyethylene and e-glass on the mesiolingual cavity of ETT.

Materials and Methods

A three-dimensional model of the mandibular molar was prepared for cavity preparation and the formation of restorations using SolidWorks 2021. The models were analyzed with Abaqus 2020 to determine stress concentrations after given vertical and oblique loading.

Results

The maximum and minimum principal stress data were obtained to assess material resistance and interfacial damage criterion. Polyethylene fiber shows a more homogeneous stress distribution because the modulus of elasticity is close to the dentin and has a thickness that can reduce the volume of the composite. The E-glass shows the stress concentration on the circumferential fiber and cavity floor.

Conclusion

The stress distribution of fiber-reinforced composite on the buccolingual cavity of ETT using the finite element method did not show structural failure in the polyethylene group because the maximum and minimum principal stresses were lower than the strength of the material. Interfacial bond failure occurs at the enamel portion. The maximum and minimum principal values of e-glass indicate structural failure in the circumferential fiber and the base fiber because the stress exceeds the strength of the material. Interfacial bond failure occurred on the circumferential and the cavity floor.

Effect of Fiber Posts on Stress Distribution of Endodontically Treated Upper Premolars: Finite Element Analysis

By means of a finite element method (FEM), the present study evaluated the effect of fiber post (FP) placement on the stress distribution occurring in endodontically treated upper first premolars (UFPs) with mesial–occlusal–distal (MOD) nanohybrid composite restorations under subcritical static load. FEM models were created to simulate four different clinical situations involving endodontically treated UFPs with MOD cavities restored with one of the following: composite resin; composite and one FP in the palatal root; composite and one FP in the buccal root; or composite and two FPs. As control, the model of an intact UFP was included. A simulated load of 150 N was applied. Stress distribution was observed on each model surface, on the mid buccal–palatal plane, and on two horizontal planes (at cervical and root-furcation levels); the maximum Von Mises stress values were calculated. All analyses were replicated three times, using the mechanical parameters from three different nanohybrid resin composite restorative materials. In the presence of FPs, the maximum stress values recorded on dentin (in cervical and root-furcation areas) appeared slightly reduced, compared to the endodontically treated tooth restored with no post; in the same areas, the overall Von Mises maps revealed more favorable stress distributions. FPs in maxillary premolars with MOD cavities can lead to a positive redistribution of potentially dangerous stress concentrations away from the cervical and the root-furcation dentin.