Quantitative analysis of adhesion and biofilm formation on hydrophilic and hydrophobic surfaces of clinical isolates of Staphylococcus epidermidis

Effects of different sterilization techniques and varying anodized TiO₂ nanotube dimensions on bacteria growth

Infection of titanium (Ti)-based orthopedic implants is a growing problem due to the ability of bacteria to develop a resistance to today's antibiotics. As an attempt to develop a new strategy to combat bacteria functions, Ti was anodized in the present study to possess different diameters of nanotubes. It is reported here for the first time that Ti anodized to possess 20 nm tubes then followed by heat treatment to remove fluorine deposited from the HF anodization electrolyte solution significantly reduced both S. aureus and S. epidermidis growth compared to unanodized Ti controls. It was further found that the sterilization method used for both anodized nanotubular Ti and conventional Ti played an important role in the degree of bacteria growth on these substrates. Overall, UV light and ethanol sterilized samples decreased bacteria growth, while autoclaving resulted in the highest amount of bacteria growth. In summary, this study indicated that through a simple and inexpensive process, Ti can be anodized to possess 20 nm tubes that no matter how sterilized (UV light, ethanol soaking, or autoclaving) reduces bacteria growth and, thus, shows great promise as an antibacterial implant material.

Reducing Staphylococcus aureus biofilm formation on stainless steel 316L using functionalized self-assembled monolayers

Stainless steel 316L (SS316L) is a common material used in orthopedic implants. Bacterial colonization of the surface and subsequent biofilm development can lead to refractory infection of the implant. Since the greatest risk of infection occurs perioperatively, strategies that reduce bacterial adhesion during this time are important. As a strategy to limit bacterial adhesion and biofilm formation on SS316L, self-assembled monolayers (SAMs) were used to modify the SS316L surface. SAMs with long alkyl chains terminated with hydrophobic (-CH3) or hydrophilic (oligoethylene glycol) tail groups were used to form coatings and in an orthogonal approach, SAMs were used to immobilize gentamicin or vancomycin on SS316L for the first time to form an "active" antimicrobial coating to inhibit early biofilm development. Modified SS316L surfaces were characterized using surface infrared spectroscopy, contact angles, MALDI-TOF mass spectrometry and atomic force microscopy. The ability of SAM-modified SS316L to retard biofilm development by Staphylococcus aureus was functionally tested using confocal scanning laser microscopy with COMSTAT image analysis, scanning electron microscopy and colony forming unit analysis. Neither hydrophobic nor hydrophilic SAMs reduced biofilm development. However, gentamicin-linked and vancomycin-linked SAMs significantly reduced S. aureus biofilm formation for up to 24 and 48 h, respectively.

Phenotypic antibiotic resistance of Escherichia coli and E. coli O157 isolated from water, sediment and biofilms in an agricultural watershed in British Columbia

This study examined the distribution of antibiotic resistant Escherichia coli and E. coli O157 isolated from water, sediment and biofilms in an intensive agricultural watershed (Elk Creek, British Columbia) between 2005 and 2007. It also examined physical and chemical water parameters associated with antibiotic resistance. Broth microdilution techniques were used to determine minimum inhibitory concentrations (MIC) for E. coli (n=214) and E. coli O157 (n=27) recovered isolates for ampicillin, cefotaxime, ciprofloxacin, nalidixic acid, streptomycin and tetracycline. Both E. coli and E. coli O157 isolates showed highest frequency of resistance to tetracycline, ampicillin, streptomycin and nalidixic acid; respectively. For E. coli, the highest frequency of resistance was observed at the most agriculturally-impacted site, while the lowest frequency of resistance was found at the headwaters. Sediment and river rock biofilms were the most likely to be associated with resistant E. coli, while water was the least likely. While seasonality (wet versus dry) had no relationship with resistance frequency, length of biofilm colonization of the substratum in the aquatic environment only affected resistance frequency to nalidixic acid and tetracycline. Multivariate logistic regressions showed that water depth, nutrient concentrations, temperature, dissolved oxygen and salinity had statistically significant associations with frequency of E. coli resistance to nalidixic acid, streptomycin, ampicillin and tetracycline. The results indicate that antibiotic resistant E. coli and E. coli O157 were prevalent in an agricultural stream. Since E. coli is adept at horizontal gene transfer and prevalent in biofilms and sediment, where ample opportunities for genetic exchange with potential environmental pathogens present themselves, resistant isolates may present a risk to ecosystem, wildlife and public health.

Disruption of lmo1386, a putative DNA translocase gene, affects biofilm formation of Listeria monocytogenes on abiotic surfaces

The distribution and survival of Listeria monocytogenes (L. monocytogenes) in food processing environment is linked to its ability to form biofilms, however the genetic mechanisms remain unclear. In our previous study, a Himar1 mariner-based transposon mutagenesis was performed and 42 mutants were confirmed to have reduced biofilm formation. Among the 42 biofilm deficient mutants, two isolates (s25-10C and s55-1D) harbored single insertion in lmo1386, a gene encoding a putative DNA translocase. The lmo1386 mutants had impaired biofilm formation in both static and flow conditions. The mutant strain s55-1D was complemented by cloning the entire lmo1386 gene into pPL2-gtcAP, a derivative of the integration vector pPL2 with the L. monocytogenes gtcA promoter. The genetically complemented mutant restored its biofilm phenotype, demonstrating the role of lmo1386 in the biofilm formation of L. monocytogenes. The lmo1386 mutant had reduced initial adhesion ability, which could at least partially contribute to the impaired biofilm phenotype. Additionally, the lmo1386 mutant formed elongated cell chains when grown in a nutrient TSBYE media, while no obvious cell morphology changes were observed when grown in the minimal MWB media. Overall, our findings suggest that the disruption of lmo1386, a putative DNA translocase gene affects the biofilm formation of L. monocytogenes on abiotic surfaces, which may further advance the understanding of the complicated process of biofilm formation.

Purification and characterization of a surfactin-like molecule produced by Bacillus sp. H2O-1 and its antagonistic effect against sulfate reducing bacteria

Background

Bacillus sp. H2O-1, isolated from the connate water of a Brazilian reservoir, produces an antimicrobial substance (denoted as AMS H2O-1) that is active against sulfate reducing bacteria, which are the major bacterial group responsible for biogenic souring and biocorrosion in petroleum reservoirs. Thus, the use of AMS H2O-1 for sulfate reducing bacteria control in the petroleum industry is a promising alternative to chemical biocides. However, prior to the large-scale production of AMS H2O-1 for industrial applications, its chemical structure must be elucidated. This study also analyzed the changes in the wetting properties of different surfaces conditioned with AMS H2O-1 and demonstrated the effect of AMS H2O-1 on sulfate reducing bacteria cells.

Results

A lipopeptide mixture from AMS H2O-1 was partially purified on a silica gel column and identified via mass spectrometry (ESI-MS). It comprises four major components that range in size from 1007 to 1049 Da. The lipid moiety contains linear and branched β-hydroxy fatty acids that range in length from C13 to C16. The peptide moiety contains seven amino acids identified as Glu-Leu-Leu-Val-Asp-Leu-Leu.

Transmission electron microscopy revealed cell membrane alteration of sulfate reducing bacteria after AMS H2O-1 treatment at the minimum inhibitory concentration (5 μg/ml). Cytoplasmic electron dense inclusions were observed in treated cells but not in untreated cells. AMS H2O-1 enhanced the osmosis of sulfate reducing bacteria cells and caused the leakage of the intracellular contents. In addition, contact angle measurements indicated that different surfaces conditioned by AMS H2O-1 were less hydrophobic and more electron-donor than untreated surfaces.

Conclusion

AMS H2O-1 is a mixture of four surfactin-like homologues, and its biocidal activity and surfactant properties suggest that this compound may be a good candidate for sulfate reducing bacteria control. Thus, it is a potential alternative to the chemical biocides or surface coating agents currently used to prevent SRB growth in petroleum industries.

Structural, physicochemical and microbial properties of flocs and biofilms in integrated fixed-film activated sludge (IFFAS) systems

Integrated fixed-film activated sludge systems (IFFAS) may achieve year-round nitrification or gain additional treatment capacity due to the presence of both flocs and biofilms, and the potential for multiple redox states and long solids retention time. Flocs and biofilms are distinctive microbial structures and characterization of the physicochemical and structural properties of these may provide insight into their respective roles in wastewater treatment and contaminant removal in IFFAS. Flocs and biofilms were examined from five different pilot media systems being evaluated for potential full scale implementation at a large municipal wastewater treatment plant. Flocs and biofilms within the same system possessed different surface characteristics; flocs were found to have a higher negative surface charge (-0.35 to -0.65 meq./g VSS) and are more hydrophobic (60%-75%) than biofilms (-0.05 to -0.07 meq/g VSS; 19-34%). The EPS content of flocs was significantly higher (range of 2.1-4.5 folds) than that of biofilms. In floc-derived extracellular polymeric substances (EPS), protein (PN) was clearly dominant; whereas in biofilm-derived EPS, PN and polysaccharide (PS) were present in approximately equal proportions. Biofilm EPS had a higher proportion of DNA when compared to flocs. Biofilm growth was preferential on the protected internal surfaces of the media. Colonization of the external surfaces of the media was evident by the presence of small microcolonies. The structural heterogeneity of the biofilms examined was supported by observed differences in biomass content, thickness and roughness of biofilm surface. The biofilm on the interior surface of media was found to be patchy with clusters of cells connected by an irregular arrangement of interconnecting EPS projections. Biofilm thickness ranged between 139 μm and 253 μm. The pattern of oxygen penetration is expected to be complex. Nitrifiers and denitrifiers were predominantly associated with the biofilms, and the latter were found to be dispersed throughout the film and arranged in micro-clusters, suggesting partial oxygen penetration.

Effects of Bacillus anthracis hydrophobicity and induction of host cell death on sample collection from environmental surfaces

The objective of this study is to determine whether DNA signature recovery of Bacillus anthracis strains from different environmental substrates correlates with pathogen cell surface hydrophobicity and induction of host cell death. We compared recovery of DNA signatures from a panel of B. anthracis strains collected from two environmental substrates, non-porous surfaces and soil, using real-time qPCR. We further assessed both cell surface hydrophobicity of the B. anthracis strains by contact angle measurements and host cell viability in response to B. anthracis infection in a mouse macrophage cell model system. Our studies demonstrated correlation between reduced B. anthracis sample recovery from environmental substrates and increased cell surface hydrophobicity. Surprisingly, the most hydrophilic strain, K4596, which exhibited the highest level of recovery from the environmental surfaces, induced the highest level of host cell cytotoxicity compared to more hydrophobic B. anthracis strains in the panel. Our results suggest that cell surface hydrophobicity may play a leading role in mediating pathogen adherence to environmental surfaces. These findings can contribute to the optimization of pathogen detection efforts by understanding how bacterial parameters such as hydrophobicity and induction of host cell death affect bacterial adherence to environmental surfaces.

Detection of biofilm-grown Aspergillus fumigatus by means of atomic force spectroscopy: ultrastructural effects of alginate lyase

Aspergillus fumigatus has become a leading cause of fungal morbidity and mortality, especially in immunocompromised patients. This fungus is able to grow as a multicellular community and produce a hydrophobic extracellular matrix (ECM), mainly composed of galactomannan and α-1,3 glucans, to protect itself from host defenses and antimicrobial drugs. This matrix envelops the fungus hyphae, binding them into a contiguous sheath on the colony surface, forming a biofilm and increasing the fungal resistance to adverse environmental factors. Adherence to host cells and resistance to physical removal play a key role in fungal colonization and invasion of the host and in a wide range of infections. Here we show that, by using atomic force spectroscopy, it is possible to exploit the peculiar hydrophobicity of the biofilm components (i.e., cell walls, ECM) to detect the biofilm spread, its growth, and lysis on rough surfaces. By means of this approach, we demonstrate that alginate lyase, an enzyme known to reduce negatively charged alginate levels in microbial biofilms, reduces the biofilm adhesion forces suggesting a loss of ECM from the biofilm, which could be used to enhance pharmacological treatments.

Adhesion of Staphylococcus epidermidis to biomaterials is inhibited by fibronectin and albumin

Decades of contradictory results have obscured the exact role of adsorbed fibronectin in the adhesion of the bacterium, Staphylococcus epidermidis, to biomaterials. Here, the ability of adsorbed fibronectin (FN) or bovine serum albumin (BSA) to modulate S. epidermidis adhesion to various biomaterials is reported. FN or BSA was adsorbed in increasing surface densities up to saturated monolayer coverage onto various common biomaterials, including poly(ethylene terephthalate), fluorinated ethylene propylene, poly(ether urethane), silicone, and borosilicate glass. Despite the wide range of surface characteristics represented, adsorption isotherms varied only subtly between materials for the two proteins considered. S. epidermidis adhesion to the various protein-coated biomaterials was quantified in a static-fluid batch adhesion assay. Although slight differences in overall adherent cell numbers were observed between the various protein-coated substrata, all materials exhibited significant dose-dependent decreases in S. epidermidis adhesion with increasing adsorption of either protein (FN, BSA) to all surfaces. Results here indicate that S. epidermidis adhesion to FN-coated surfaces is not a specific adhesion (i.e., receptor: ligand) mediated process, as no significant difference in adhesion was found between FN- and BSA-coated materials. Rather, results indicate that increasing surface density of either FN or BSA actually inhibited S. epidermidis adhesion to all biomaterials examined.

Optimizing a qPCR gene expression quantification assay for S. epidermidis biofilms: a comparison between commercial kits and a customized protocol

Staphylococcus epidermidis biofilm-related infections are a current concern within the medical community due to their high incidence and prevalence, particularly in patients with indwelling medical devices. Biofilm gene expression analysis by quantitative real-time PCR (qPCR) has been increasingly used to understand the role of biofilm formation in the pathogenesis of S. epidermidis infections. However, depending on the RNA extraction procedure, and cDNA synthesis and qPCR master mixes used, gene expression quantification can be suboptimal. We recently showed that some RNA extraction kits are not suitable for S. epidermidis biofilms, due to sample composition, in particular the presence of the extracellular matrix. In this work, we describe a custom RNA extraction assay followed by the evaluation of gene expression using different commercial reverse transcriptase kits and qPCR master mixes. Our custom RNA extraction assay was able to produce good quality RNA with reproducible gene expression quantification, reducing the time and the costs associated. We also tested the effect of reducing cDNA and qPCR reaction volumes and, in most of the cases tested, no significant differences were found. Finally, we titered the SYBR Green I concentrations in standard PCR master mixes and compared the normalized expression of the genes icaA, bhp, aap, psmβ1 and agrB using 4 distinct biofilm forming S. epidermidis strains to the results obtained with commercially available kits. The overall results demonstrated that despite some statistically, but not biologically significant differences observed, the customized qPCR protocol resulted in the same gene expression trend presented by the commercially available kits used.

Confocal laser scanning microscopy analysis of S. epidermidis biofilms exposed to farnesol, vancomycin and rifampicin

Background

Staphylococcus epidermidis is the major bacterial species found in biofilm-related infections on indwelling medical devices. Microbial biofilms are communities of bacteria adhered to a surface and surrounded by an extracellular polymeric matrix. Biofilms have been associated with increased antibiotic tolerance to the immune system. This increased resistance to conventional antibiotic therapy has lead to the search for new antimicrobial therapeutical agents. Farnesol, a quorum-sensing molecule in Candida albicans, has been described as impairing growth of several different microorganisms and we have previously shown its potential as an adjuvant in antimicrobial therapy against S. epidermidis. However, its mechanism of action in S. epidermidis is not fully known. In this work we better elucidate the role of farnesol against S: epidermidis biofilms using confocal laser scanning microscopy (CLSM).

Findings

24 h biofilms were exposed to farnesol, vancomycin or rifampicin and were analysed by CLSM, after stained with a Live/Dead stain, a known indicator of cell viability, related with cell membrane integrity. Biofilms were also disrupted by sonication and viable and cultivable cells were quantified by colony forming units (CFU) plating. Farnesol showed a similar effect as vancomycin, both causing little reduction of cell viability but at the same time inducing significant changes in the biofilm structure. On the other hand, rifampicin showed a distinct action in S. epidermidis biofilms, by killing a significant proportion of biofilm bacteria.

Conclusions

While farnesol is not very efficient at killing biofilm bacteria, it damages cell membrane, as determined by the live/dead staining, in a similar way as vancomycin. Furthermore, farnesol might induce biofilm detachment, as determined by the reduced biofilm biomass, which can partially explain the previous findings regarding its role as a possible chemotherapy adjuvant.

Effect of alkaline pH on staphylococcal biofilm formation

Biofilms are a serious problem, cause of severe inconvenience in the biomedical, food and industrial environment. Staphylococcus aureus and S. epidermidis are important pathogenic bacteria able to form thick and resistant biofilms on various surfaces. Therefore, strategies aimed at preventing or at least interfering with the initial adhesion and subsequent biofilm formation are a considerable achievement. The aim of this study was to evaluate the effect of alkaline pH on bacterial adhesion and further biofilm formation of S. aureus and S. epidermidis strains by biofilm biomass, cell-surface hydrophobicity, scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) analysis. The results demonstrated that the amount of biofilm biomass formed and the surface hydrophobicity were significantly less than what were observed at higher levels of pH. SEM and CLSM images revealed a poorly structured and very thin biofilm (2.5-3 times thinner than that of the controls). The inhibiting effect of the alkaline pH on the bacterial attachment impaired the normal development of biofilm that arrested at the microcolony stage. Alkaline formulations could be promising towards the control of bacterial colonization and therefore the reduction of the biofilm-related hazard. In the clinical setting, alkaline solutions or cleaners could be promising to prevent the bacterial colonization, by treating surfaces such as catheters or indwelling medical devices, reducing the risk of biofilm related infections.

Preparation and rapid analysis of antibacterial silver, copper and zinc doped sol-gel surfaces

The colonisation of clinical and industrial surfaces with microorganisms, including antibiotic-resistant strains, has promoted increased research into the development of effective antibacterial and antifouling coatings. This study describes the preparation of metal nitrate (Ag, Cu, Zn) doped methyltriethoxysilane (MTEOS) coatings and the rapid assessment of their antibacterial activity using polyproylene microtitre plates. Microtitre plate wells were coated with different volumes of liquid sol-gel and cured under various conditions. Curing parameters were analysed by thermogravimetric analysis (TGA) and visual examination. The optimum curing conditions were determined to be 50-70°C using a volume of 200 μl. The coated wells were challenged with Gram-positive and Gram-negative bacterial cultures, including biofilm-forming and antibiotic-resistant strains. The antibacterial activities of the metal doped sol-gel, at equivalent concentrations, were found to have the following order: silver>zinc>copper. The order is due to several factors, including the increased presence of silver nanoparticles at the sol-gel coating surface, as determined by X-ray photoelectron spectroscopy, leading to higher elution rates as measured by inductively coupled plasma atomic emission spectroscopy (ICP-AES). The use of microtitre plates enabled a variety of sol-gel coatings to be screened for their antibacterial activity against a wide range of bacteria in a relatively short time. The broad-spectrum antibacterial activity of the silver doped sol-gel showed its potential for use as a coating for biomaterials.

Gas-phase removal of biofilms from various surfaces using carbon dioxide aerosols

The present study evaluated the removal of Escherichia coli XL1-blue biofilms using periodic jets of carbon dioxide aerosols (a mixture of solid and gaseous CO(2)) with nitrogen gas. The aerosols were generated by the adiabatic expansion of high-pressure CO(2) gas through a nozzle and used to remove air-dried biofilms. The areas of the biofilms were measured from scanning electron micrographs before and after applying the aerosols. The removal efficiency of the aerosol treatment was measured with various air-drying times of the biofilms before the treatment, surface materials, and durations of CO(2) aerosols in each 8-s aerosol-nitrogen cleaning cycle. Nearly 100% of the fresh biofilms were removed from the various surfaces very reliably within 90 s. This technique can be useful for removing unsaturated biofilms on solid surfaces and has potential applications for cleaning bio-contaminated surfaces.

Comparison of RNA extraction methods from biofilm samples of Staphylococcus epidermidis

Background

Microbial biofilms are communities of bacteria adhered to a surface and surrounded by an extracellular polymeric matrix. Biofilms have been associated with increased antibiotic resistance and tolerance to the immune system. Staphylococcus epidermidis is the major bacterial species found in biofilm-related infections on indwelling medical devices. Obtaining high quality mRNA from biofilms is crucial to validate the transcriptional measurements associated with the switching to the biofilm mode of growth. Therefore, we selected three commercially available RNA extraction kits with distinct characteristics, including those using silica membrane or organic extraction methods, and enzymatic or mechanical cell lysis, and evaluated the RNA quality obtained from two distinct S. epidermidis bacterial biofilms.

Results

RNA extracted using the different kits was evaluated for quantity, purity, integrity, and functionally. All kits were able to extract intact and functional total RNA from the biofilms generated from each S. epidermidis strain. The results demonstrated that the kit based on mechanical lysis and organic extraction (FastRNA^® Pro Blue) was the only one that was able to isolate pure and large quantities of RNA. Normalized expression of the icaA virulence gene showed that RNA extracted with PureLink™ had a significant lower concentration of icaA mRNA transcripts than the other kits tested.

Conclusions

When working with complex samples, such as biofilms, that contain a high content extracellular polysaccharide and proteins, special care should be taken when selecting the appropriate RNA extraction system, in order to obtain accurate, reproducible, and biologically significant results. Among the RNA extraction kits tested, FastRNA^® Pro Blue was the best option for both S. epidermidis biofilms used.

Vitamin E blended UHMWPE may have the potential to reduce bacterial adhesive ability

Biomaterial-associated infection (BAI), a clinical problem resulting in septic failure of joint replacement implants, is initiated by bacterial adhesion, often by Staphylococcus epidermidis. Ultra high molecular weight polyethylene (UHMWPE) is a material of choice for joint replacement; reducing the adhesion of S. epidermidis to the polymer could be a means to decrease infection. We examined the adhesion of two ATCC and one clinical strain of S. epidermidis to standard polyethylene (PE), vitamin E blended UHMWPE (VE-PE), and oxidized UHMWPE (OX-PE) after different incubation times: a significant (p < 0.01) decrease in the adhered staphylococci on VE-PE and a significantly higher incidence of the dislodged biofilm bacteria on OX-PE was observed compared with that registered on PE. With attenuated total reflectance (ATR)-FTIR spectroscopy before and after suspension in bacterial medium for 48 h, new absorptions were observed mainly in OX-PE, indicating adsorption of protein-like substances on the polymer surface. We hypothesized that the different hydrophilicity of the surfaces with different chemical characteristics influenced protein adsorption and bacterial adhesion. These results may have clinical implications concerning the prevention of septic loosening: the VE-PE could have the potential to reduce S. epidermidis adhesive ability if the preliminary data observed in these selected strains is further confirmed, as diversity among clinical strains is well known. 

Antibiotic-loaded cement in orthopedic surgery: a review

Infections in orthopaedic surgery are a serious issue. Antibiotic-loaded bone cement was developed for the treatment of infected joint arthroplasties and for prophylaxes in total joint replacement in selected cases. Despite the widespread use of the antibiotic-loaded bone cement in orthopedics, many issues are still unclear or controversial: bacterial adhesion and antibiotic resistance, modification of mechanical properties which follows the addition of the antibiotic, factors influencing the release of the antibiotic from the cement and the role of the surface, the method for mixing the cement and the antibiotic, the choice and the effectiveness of the antibiotic, the combination of two or more antibiotics, and the toxicity. This review discusses all these topics, focusing on properties, merits, and defects of the antibiotic loaded cement. The final objective is to provide the orthopaedic surgeons clear and concise information for the correct choice of cement in their clinical practice.

Diameter of titanium nanotubes influences anti-bacterial efficacy

Bacterial infection of in-dwelling medical devices is a growing problem that cannot be treated by traditional antibiotics due to the increasing prevalence of antimicrobial resistance and biofilm formation. Here, due to changes in surface parameters, it is proposed that bacterial adhesion can be prevented through nanosurface modifications of the medical device alone. Toward this goal, titanium was created to possess nanotubular surface topographies of highly controlled diameters of 20, 40, 60, or 80 nm, sometimes followed by heat treatment to control chemistry and crystallinity, through a novel anodization process. For the first time it was found that through the control of Ti surface parameters including chemistry, crystallinity, nanotube size, and hydrophilicity, significantly changed responses of both Staphylococcus epidermidis and Staphylococcus aureus (pathogens relevant for orthopaedic and other medical device related infections) were measured. Specifically, heat treatment of 80 nm diameter titanium tubes produced the most robust antimicrobial effect of all surface treatment parameters tested. This study provides the first step toward understanding the surface properties of nano-structured titanium that improve tissue growth (as has been previously observed with nanotubular titanium), while simultaneously reducing infection without the use of pharmaceutical drugs.

Development of bacterial biofilms on artificial corals in comparison to surface-associated microbes of hard corals

Numerous studies have demonstrated the differences in bacterial communities associated with corals versus those in their surrounding environment. However, these environmental samples often represent vastly different microbial micro-environments with few studies having looked at the settlement and growth of bacteria on surfaces similar to corals. As a result, it is difficult to determine which bacteria are associated specifically with coral tissue surfaces. In this study, early stages of passive settlement from the water column to artificial coral surfaces (formation of a biofilm) were assessed. Changes in bacterial diversity (16S rRNA gene), were studied on artificially created resin nubbins that were modelled from the skeleton of the reef building coral Acropora muricata. These models were dip-coated in sterile agar, mounted in situ on the reef and followed over time to monitor bacterial community succession. The bacterial community forming the biofilms remained significantly different (R = 0.864 p<0.05) from that of the water column and from the surface mucus layer (SML) of the coral at all times from 30 min to 96 h. The water column was dominated by members of the α-proteobacteria, the developed community on the biofilms dominated by γ-proteobacteria, whereas that within the SML was composed of a more diverse array of groups. Bacterial communities present within the SML do not appear to arise from passive settlement from the water column, but instead appear to have become established through a selection process. This selection process was shown to be dependent on some aspects of the physico-chemical structure of the settlement surface, since agar-coated slides showed distinct communities to coral-shaped surfaces. However, no significant differences were found between different surface coatings, including plain agar and agar enhanced with coral mucus exudates. Therefore future work should consider physico-chemical surface properties as factors governing change in microbial diversity.

Hacking into bacterial biofilms: a new therapeutic challenge

Microbiologists have extensively worked during the past decade on a particular phase of the bacterial cell cycle known as biofilm, in which single-celled individuals gather together to form a sedentary but dynamic community within a complex structure, displaying spatial and functional heterogeneity. In response to the perception of environmental signals by sensing systems, appropriate responses are triggered, leading to biofilm formation. This process involves various molecular systems that enable bacteria to identify appropriate surfaces on which to anchor themselves, to stick to those surfaces and to each other, to construct multicellular communities several hundreds of micrometers thick, and to detach from the community. The biofilm microbial community is a unique, highly competitive, and crowded environment facilitating microevolutionary processes and horizontal gene transfer between distantly related microorganisms. It is governed by social rules, based on the production and use of "public" goods, with actors and recipients. Biofilms constitute a unique shield against external aggressions, including drug treatment and immune reactions. Biofilm-associated infections in humans have therefore generated major problems for the diagnosis and treatment of diseases. Improvements in our understanding of biofilms have led to innovative research designed to interfere with this process.

"Biofilmology": a multidisciplinary review of the study of microbial biofilms

The observation of biofilm formation is not a new phenomenon. The prevalence and significance of biofilm and aggregate formation in various processes have encouraged extensive research in this field for more than 40 years. In this review, we highlight techniques from different disciplines that have been used to successfully describe the extracellular, surface and intracellular elements that are predominant in understanding biofilm formation. To reduce the complexities involved in studying biofilms, researchers in the past have generally taken a parts-based, disciplinary specific approach to understand the different components of biofilms in isolation from one another. Recently, a few studies have looked into combining the different techniques to achieve a more holistic understanding of biofilms, yet this approach is still in its infancy. In order to attain a global understanding of the processes involved in the formation of biofilms and to formulate effective biofilm control strategies, researchers in the next decade should recognise that the study of biofilms, i.e. biofilmology, has evolved into a discipline in its own right and that mutual cooperation between the various disciplines towards a multidisciplinary research vision is vital in this field.

Surface hydrophobicity, nutritional contents affect Staphylococcus aureus biofilms and temperature influences its survival in preformed biofilms

The present study investigates the effect of surface hydrophobicity and media on in vitro biofilm formation potential of S. aureus isolates from two dairies. There was lack of correlation between biofilm formation potential of S. aureus and sampling points but not with the source of isolation. Biofilm formation was more pronounced on hydrophobic polypropylene (PP) than hydrophilic stainless steel (SSC). A better correlation was established between the biofilms on SSC and PP when analyzed by crystal violet staining than conventional plating method. On comparative evaluation of nutrient rich and diluted growth media, enhanced biofilm formation was observed in latter (1/20 tryptic soya broth). Highest survival in the preformed biofilms was observed at incubation temperature of 25 °C in sterilized skim milk rather than TSB. The present study signify preferable adherence of S. aureus on hydrophobic surfaces and potential survival within preformed biofilm at temperatures prevalent in dairy industries.

Farnesol as antibiotics adjuvant in Staphylococcus epidermidis control in vitro

INTRODUCTION

Farnesol is a sesquiterpenoid that has been described as impairing bacterial growth. Therefore, the goal of this study was to compare the in vitro postantimicrobial effect (PAE) of farnesol against Staphylococcus epidermidis with the corresponding values of most common practice antibiotics and also to evaluate the combined effect of farnesol with these antibiotics against planktonic and biofilm cells.

METHODS

After exposure of S epidermidis cells to farnesol and antibiotics at minimum inhibitory concentration for 1 hour, the cells were regrown in medium without any antimicrobial agent. Cellular viability was assessed by colony-forming units, every hour for 12 hours, and then, the PAE was determined. The combined effect of farnesol (0, 30, 100 and 300 μM) with vancomycin, tetracycline and rifampicin was also evaluated, by using these antibiotics at peak serum concentration.

RESULTS

When PAE is concerned, it was found that cells grown in 100 μM of farnesol behaved similarly to cells that had never been in contact with farnesol, whereas a clear difference was obtained with cells exposed to 300 μM of farnesol, displaying a longer PAE. Farnesol showed a combined effect with the tested antibiotics against planktonic cells, although this was not so evident against biofilm cells.

CONCLUSIONS

Despite the reduced efficacy against biofilm cells, farnesol seems to be a potential adjuvant therapeutic agent to antibiotics against S epidermidis planktonic cells. Moreover, its long PAE makes farnesol a potential candidate in the prevention of biofilm formation because it showed to be very effective against planktonic cells alone as well.

Lens material and formulation of multipurpose solutions affects contact lens disinfection

PURPOSE

To assess the disinfection efficacy of multipurpose solutions (MPS) against different bacterial species adhered either to silicon hydrogel or to conventional hydrogel contact lenses (CLs). The influences of the MPS formulation and the chemical composition of the lens material were investigated.

METHODS

This investigation followed the standard 14729, which establishes the guidelines for assessing CL disinfecting solutions. Two commercially available (Opti-Free(®) Express(®) and Renu(®) Multiplus) solutions and one recalled solution (Complete(®) MoisturePlus™) were used in this study. After disinfection, the number of survivors was estimated by the colony forming units' method.

RESULTS

The lens material appears to influence disinfection. The conventional hydrogel polymacon exhibited the highest disinfection scores, a fact that should be related with the lack of electrostatic attraction towards the biocides and its hydrophilicity. The MPS formulation appears to have influence in disinfection efficacy as well. For most adhered bacteria, Opti-Free(®) was capable of reducing cell concentration in 4-log.

CONCLUSION

Disinfection results from multivariate factors and this study confirmed that the lens material and the MPS play a very important role in the disinfection efficacy of CL.

In vitro adhesion of staphylococci to diamond-like carbon polymer hybrids under dynamic flow conditions

This study compares the ability of selected materials to inhibit adhesion of two bacterial strains commonly implicated in implant-related infections. These two strains are Staphylococcus aureus (S-15981) and Staphylococcus epidermidis (ATCC 35984). In experiments we tested six different materials, three conventional implant metals: titanium, tantalum and chromium, and three diamond-like carbon (DLC) coatings: DLC, DLC-polydimethylsiloxane hybrid (DLC-PDMS-h) and DLC-polytetrafluoroethylene hybrid (DLC-PTFE-h) coatings. DLC coating represents extremely hard material whereas DLC hybrids represent novel nanocomposite coatings. The two DLC polymer hybrid films were chosen for testing due to their hardness, corrosion resistance and extremely good non-stick (hydrophobic and oleophobic) properties. Bacterial adhesion assay tests were performed under dynamic flow conditions by using parallel plate flow chambers (PPFC). The results show that adhesion of S. aureus to DLC-PTFE-h and to tantalum was significantly (P < 0.05) lower than to DLC-PDMS-h (0.671 ± 0.001 × 10(7)/cm(2) and 0.751 ± 0.002 × 10(7)/cm(2) vs. 1.055 ± 0.002 × 10(7)/cm(2), respectively). No significant differences were detected between other tested materials. Hence DLC-PTFE-h coating showed as low susceptibility to S. aureus adhesion as all the tested conventional implant metals. The adherence of S. epidermidis to biomaterials was not significantly (P < 0.05) different between the materials tested. This suggests that DLC-PTFE-h films could be used as a biomaterial coating without increasing the risk of implant-related infections.

Possible influence of surfactants and proteins on the efficiency of contact agar microbiological surface sampling

Agar contact microbiological sampling techniques, based on a transfer of the microorganisms present on a surface to a culture medium, are widely used to assess and control surface cleanliness and to evaluate microbial contamination levels. The effectiveness of these techniques depends on many environmental parameters that influence the strength of attachment of the bacteria to the surface. In the present study, stainless steel and high density polyethylene surfaces were inoculated with known concentrations of Staphylococcus epidermidis. Following an experimental design, the surfaces were sampled with different types of replicate organism direct agar contact plates and Petrifilm; results indicated that recovery rates were influenced by the presence of egg white albumin or Tween 80 in the inoculum solutions or by the introduction of surfactants into the contact agar of the microbiological sampling techniques. The techniques yielded significantly different results, depending on sampling conditions, underlining the need for a standardization of laboratory experiments to allow relevant comparisons of such techniques.

Characterization of protein degradation in serum-based lubricants during simulation wear testing of metal-on-metal hip prostheses

A size exclusion high performance liquid chromatography (SEC-HPLC) method has been developed which is capable of separation and quantitation of bovine serum albumin (BSA) and bovine serum globulin (BSG) components of serum-based lubricant (SBL) solutions. This allowed characterization of the stability profiles of these proteins when acting as lubricants during hip wear simulation, and identification of wear-specific mechanisms of degradation. Using cobalt-chromium metal-on-metal (MOM) hip joints, it was observed that BSA remained stable for up to 3 days (215K cycles) of wear testing after which the protein degraded in a fairly linear fashion. BSG on the other hand, began to degrade immediately and in a linear fashion with a rate constant of 5% per day. Loss of both proteins occurred via the formation of high molecular weight aggregates which precipitated out of solution. No fragmentation of the polypeptide backbone of either protein was observed. Data obtained suggest that protein degradation was not due to microbial contamination, denaturation at the air-water interface, or frictional heating of articulating joint surfaces in these studies. We conclude that the primary source of protein degradation during MOM simulation testing occurs via high shear rates experienced by SBL solutions at articulating surfaces, possibly coupled with metal-protein interactions occurring as new and reactive metal surfaces are generated during wear testing. The development of this analytical methodology will allow new studies to clarify the role of SBL solutions in wear simulation studies and the interactions and lubricating properties of serum proteins with prosthetic surfaces other than MOM.

Candida albicans virulence and drug-resistance requires the O-acyltransferase Gup1p

Background

GUP1 gene was primarily identified in Saccharomyces cerevisiae being connected with glycerol uptake defects in association with osmotic stress response. Soon after, Gup1p was implicated in a complex and extensive series of phenotypes involving major cellular processes. These include membrane and wall maintenance, lipid composition, bud-site selection, cytoskeleton orientation, vacuole morphology, secretory/endocytic pathway, GPI anchors remodelling, and lipid-ordered domains assembly, which is compatible with their inclusion in the Membrane Bound O-acyl transferases (MBOAT) family. In mammals, it has been described as a negative regulator of the Sonic hedgehog pathway involved in morphogenesis, differentiation, proliferation, among other processes.

Results

We show that Candida albicans Gup1p strongly interferes with the capacity of cells to develop hyphae, to adhere, to invade, and to form a biofilm, all of which are significant virulence factors. Furthermore, the mutant colonies exhibited an aberrant morphology/differentiation pattern. Identically to S. cerevisiae, Cagup1Δ null mutant was more resistant to antifungals like fluconazole, ketoconazole, and clotrimazole, and displayed an abnormal even sterol distribution at the plasma membrane.

Conclusions

This work is the first study in the opportunistic yeast Candida albicans, showing a role for the GUP1 gene in virulence as well as in the mechanisms underlying antifungal resistance. Moreover, its impact is even more significant since these results, taken together with all the knowledge about GUP1 gene (from S. cerevisiae and mammals) give consistence to the possibility that Gup1p may be part of a yeast morphogenic pathway parallel to the mammalian Hedgehog.

Fluctuation-induced attraction between adhesion sites of supported membranes

We use scaling arguments and coarse-grained Monte Carlo simulations to study the fluctuation-mediated interactions between a pair of adhesion sites of a bilayer membrane and a supporting surface. We find that the potential of mean force is an infinitely long range attractive potential that grows logarithmically with the pair distance r : ϕ(r)/k B T=c ln r, where the constant c=2 and c=1 for nonstressed and stressed membranes, respectively. When, in addition to excluded volume repulsion, the membrane also interacts with the underlying surface through a height-dependent attractive potential, the potential ϕ(r) is screened at large pair distances.

Control of biofilm formation by poly-ethylene-co-vinyl acetate films incorporating nisin

The aim of this study was to evaluate the effect of poly-ethylene-co-vinyl acetate (EVA) films incorporating different concentrations (0.1%, 0.5% and 1%) of nisin on the biofilm-forming ability of Listeria monocytogenes ATCC 7644, Staphylococcus aureus 815 and Staphylococcus epidermidis ATCC 35984. Nisin was incorporated into two grades of EVA (EVA14 and EVA28) in the melt during a common film-blowing operation. The efficacy of EVA/nisin films was evaluated by biofilm biomass measurements and Live/Dead staining in combination with fluorescence microscopy. In order to evaluate whether the nisin incorporation could modify the film surface properties, contact angle measurements and scanning electron microscopy were performed. The results revealed the efficacy of EVA14/nisin films in reducing biofilm formation on their surfaces with more evident effect for S. epidermidis than L. monocytogenes and S. aureus strains. In contrast, EVA28/nisin films showed unsatisfactory activity. Fluorescence microscopy confirmed poor biofilm formation on EVA14/nisin films, also characterised by the presence of dead cells. The data presented in this study offer new potential applications for developing strategies aimed to improve the effect of antimicrobial agents.

Efficient degradation of lube oil by a mixed bacterial consortium

A laboratory study was performed to assess the biodegradation of lube oil in bio-reactor with 304# stainless steel as a biofilm carrier. Among 164 oil degrading bacterial cultures isolated from oil contaminated soil samples, Commaonas acidovorans Pxl, Bacillus sp. Px2, Pseudomonas sp. Px3 were selected to prepare a mixed consortium for the study based on the efficiency of lube oil utilization. The percentage of oil degraded by the mixed bacterial consortium decreased slightly from 99% to 97.2% as the concentration of lube oil was increased from 2000 to 10,000 mg/L. The degradation of TDOC (total dissolved organic carbon) showed a similar tendency compared with lube oil removal, which indicated that the intermediates in degradation process hardly accumulated. Selected mixed bacterial consortium showed their edge compared to activated sludge. Scanning electron microscopy (SEM) photos showed that biofilms on stainless steel were robust and with a dimensional framework constructed by EPS (extracellular polymeric substances), which could promote the biodegradation of hydrocarbons. The increase of biofilm followed first-order kinetics with rate of 0.216 microg glucose/(cm2-day) in logarithm phase. With analysis of Fourier transform infrared spectroscopy (FT-IR) and gas chromatography-mass spectrometry (GC-MS) combined with removal of lube oil and TDOC, mixed bacterial consortium could degrade benzene and its derivatives, aromatic ring organic matters with a percentage over 97%.

Silver doped perfluoropolyether-urethane coatings: antibacterial activity and surface analysis

The colonisation of clinical and industrial surfaces with pathogenic microorganisms has prompted increased research into the development of effective antibacterial and antifouling coatings. There is evidence that implanted biomedical surfaces coated with metallic silver can be inactivated by physiological fluids, thus reducing the bioactivity of the coating. In this work, we report the biofilm inhibition of Staphylococcus epidermidis using a room temperature processed silver doped perfluoropolyether-urethane coating. The release of silver ions from these fluoropolymers over a six-day period inhibited bacterial encrustation - as observed by scanning electron microscopy (SEM). X-ray photoelectron spectroscopy (XPS) analysis indicated differences in carbon, fluorine and sodium surface composition between silver doped and undoped fluoropolymers after exposure to nutrient rich media. These silver doped perfluoropolyether coatings also exhibited antibacterial activity against methicillin-resistant Staphylococcus aureus (MRSA), Escherichia coli, Pseudomonas aeruginosa and Acinetobacter baumannii; suggesting potential use in preventing transmission of pathogenic and opportunistic microbes on environmental surfaces in healthcare facilities. The broad-spectrum antibacterial activity of these silver release coatings may be exploited on biomaterials surfaces to combat the development of resistant Gram-negative Enterobacteriaceae that can occur during prophylactic treatment for urinary tract infections.

Influence of Surface Properties on the Adhesion of Staphylococcus epidermidis to Acrylic and Silicone

The aim of the present study was to compare the ability of eight Staphylococcus epidermidis strains to adhere to acrylic and silicone, two polymers normally used in medical devices manufacture. Furthermore, it was tried to correlate that with the surface properties of substrata and cells. Therefore, hydrophobicity and surface tension components were calculated through contact angle measurements. Surface roughness of substrata was also assessed by atomic force microscopy (AFM). No relationship was found between microbial surface hydrophobicity and adhesion capability. Nevertheless, Staphylococcus epidermidis IE214 showed very unique adhesion behaviour, with cells highly aggregated between them, which is a consequence of their specific surface features. All strains, determined as being hydrophilic, adhered at a higher extent to silicone than to acrylic, most likely due to its more hydrophobic character and higher roughness. This demonstrates the importance of biomaterial surface characteristics for bacterial adhesion.

The role of polysaccharide intercellular adhesin (PIA) in Staphylococcus epidermidis adhesion to host tissues and subsequent antibiotic tolerance

The aim of this study was to determine the role of polysaccharide intercellular adhesin (PIA) in Staphylococcus epidermidis adhesion to host tissues and subsequent antibiotic tolerance. The adherence of S. epidermidis 1457 and the mutant defective in PIA production (1457-M10) to urinary epithelium and endothelium was estimated by colony counting. Minimum bactericidal concentration and mean reduction of cellular activity (XTT) following antibiotic exposure was determined for planktonic and adhered bacteria. S. epidermidis 1457 adhered to a greater extent to both cells than the mutant strain. The adhered strains had a significantly higher antimicrobial tolerance than their planktonic counterparts. The mutant strain was, in general, the most susceptible to the antibiotics assayed. In conclusion, PIA may influence S. epidermidis adherence to host tissues and their antimicrobial susceptibility. Initial adhesion may be the main step for the acquisition of resistance in S. epidermidis.

Role of type 1 fimbriae and mannose in the development of Escherichia coli K12 biofilm: from initial cell adhesion to biofilm formation

The influence of type 1 fimbriae, mannose-sensitive structures, on biofilm development and maturation has been examined by the use of three isogenic Escherichia coli K12 strains: wild type, fimbriated, and non-fimbriated. Experiments with the three strains were done in minimal medium or Luria-Bertani broth supplemented with different concentrations of d-mannose. The investigation consisted of: (1) characterizing the bacterial surface of the three strains with respect to hydrophilicity and surface charge, (2) investigating the effect of type 1 fimbriae on bacterial adhesion rate and reversibility of initial adhesion on glass surfaces, and (3) verifying the role of type 1 fimbriae and exopolysaccharides (EPS) in biofilm maturation. The results suggest that type 1 fimbriae are not required for the initial bacterial adhesion on glass surfaces as the non-fimbriated cells had higher adhesion rates and irreversible deposition. Type 1 fimbriae, however, are critical for subsequent biofilm development. It was hypothesized that in the biofilm maturation step, the cells synthesize mannose-rich EPS, which functions as a 'conditioning film' that can be recognized by the type 1 fimbriae.