Two-Dimensional Perovskite (PEA)2PbI4 Two-Color Blue-Green Photodetector

Perovskite materials have been widely used to fabricate solar cells, laser diodes and other photodevices, owing to the advantage of high absorption coefficient, long carrier life and shallow defect energy levels. However, due to easy hydrolysis, it is difficult to fabricate perovskite micro-nano devices. Herein, we developed a water-free device fabrication technology and fabricated a two-dimensional (C₆H₅C₂H₄NH₃)₂PbI₄ ((PEA)₂PbI₄) two-color blue-green light detector, which exhibits high detection performance under the illumination of two-color lasers (λ = 460 nm, 532 nm). Compared with bulk devices, the dark current of the fabricated devices (10⁻¹¹ A) was reduced by 2 orders of magnitude. The peak responsivity and detectivity are about 1 A/W and 10¹¹ Jones, respectively. The photodetection performance of the device is basically the same under the two-color lasers. Our results provide a new process to fabricate perovskite microelectronic devices, and the fabricated photodetector shows great application prospects in underwater detection, owing to the blue-green window existing in water.

Long-range charge carrier mobility in metal halide perovskite thin-films and single crystals via transient photo-conductivity

Charge carrier mobility is a fundamental property of semiconductor materials that governs many electronic device characteristics. For metal halide perovskites, a wide range of charge carrier mobilities have been reported using different techniques. Mobilities are often estimated via transient methods assuming an initial charge carrier population after pulsed photoexcitation and measurement of photoconductivity via non-contact or contact techniques. For nanosecond to millisecond transient methods, early-time recombination and exciton-to-free-carrier ratio hinder accurate determination of free-carrier population after photoexcitation. By considering both effects, we estimate long-range charge carrier mobilities over a wide range of photoexcitation densities via transient photoconductivity measurements. We determine long-range mobilities for FA_0.83Cs_0.17Pb(I_0.9Br_0.1)₃, (FA_0.83MA_0.17)_0.95Cs_0.05Pb(I_0.9Br_0.1)₃ and CH₃NH₃PbI_3-xCl_x polycrystalline films in the range of 0.3 to 6.7 cm² V⁻¹ s⁻¹. We demonstrate how our data-processing technique can also reveal more precise mobility estimates from non-contact time-resolved microwave conductivity measurements. Importantly, our results indicate that the processing of polycrystalline films significantly affects their long-range mobility.

Charge carrier mobility is a fundamental property of semiconductors. The authors of this study demonstrate a novel way to estimate long-range mobilities of perovskite thin-films and single crystals by taking early-time carrier dynamics into account.

Thick-junction perovskite X-ray detectors: processing and optoelectronic considerations

Metal halide perovskites have attracted increasing attention due to their strong stopping power, defect tolerance, large mobility lifetime product, tunable bandgap and simple single-crystal growth via low-cost solution processes, particularly for ionizing radiation detection. Over the past few years, semiconductor-type X-ray detectors based on a variety of perovskites have been developed, showing impressive progress in achieving high sensitivity and low detection limits. In this study, based on the requirement of material properties for high-performance X-ray detectors, we review various materials used for direct detection and summarize the processing techniques and optoelectronic considerations of thick-junction perovskite X-ray detectors. This review also highlights the key challenges facing perovskite X-ray detectors towards real applications and discusses the opportunities, which are promising to explore and may require more research activities.

Electrically Pumped Polarized Exciton-Polaritons in a Halide Perovskite Microcavity

Recently, exciton-polaritons in lead halide perovskite microcavities have been extensively investigated to address striking phenomena such as polariton condensation and quantum emulation. However, a critical step in advancing these findings into practical applications, i.e., realizing electrically pumped perovskite polariton light-emitting devices, has not yet been presented. Here, we devise a new method to combine the device with a microcavity and report the first halide perovskite polariton light-emitting device. Specifically, the device is based on a CsPbBr₃ capacitive structure, which can inject the electrons and holes from the same electrode, conducive to the formation of excitons and simultaneously maintaining the high quality of the microcavity. In addition, highly polarized polariton emissions have been demonstrated due to the optical birefringence in the CsPbBr₃ microplate. This work paves the way for realizing practical polaritonic devices such as high-speed light-emitting devices for information communications and inversionless electrically pumped lasers based on perovskites.

Halide perovskite single crystals: growth, characterization, and stability for optoelectronic applications

Recently, metal halide perovskite materials have received significant attention as promising candidates for optoelectronic applications with tremendous achievements, owing to their outstanding optoelectronic properties and facile solution-processed fabrication. However, the existence of a large number of grain boundaries in perovskite polycrystalline thin films causes ion migration, surface defects, and instability, which are detrimental to device applications. Compared with their polycrystalline counterparts, perovskite single crystals have been explored to realize stable and excellent properties such as a long diffusion length and low trap density. The development of growth techniques and physicochemical characterizations led to the widespread implementation of perovskite single-crystal structures in optoelectronic applications. In this review, recent progress in the growth techniques of perovskite single crystals, including advanced crystallization methods, is summarized. Additionally, their optoelectronic characterizations are elucidated along with a detailed analysis of their optical properties, carrier transport mechanisms, defect densities, surface morphologies, and stability issues. Furthermore, the promising applications of perovskite single crystals in solar cells, photodetectors, light-emitting diodes, lasers, and flexible devices are discussed. The development of suitable growth and characterization techniques contributes to the fundamental investigation of these materials and aids in the construction of highly efficient optoelectronic devices based on halide perovskite single crystals.

Narrowband Near-Infrared Photodetectors Based on Perovskite Waveguide Devices

Organic-inorganic perovskites have attracted great interest for developing wavelength-selective photodetectors. Currently, the spectral response range of narrowband photodetectors is mainly concentrated within the visible light region, lacking near-infrared photodetectors. Here, we present perovskite narrowband near-infrared photodetectors achieved by transverse propagation of light in perovskite waveguide devices for the first time. The response spectra of photodetectors are continuously tuned from 750 to 1000 nm by changing the perovskite component and the position of the incident light with the full width at half-maximum of 25-80 nm. The theoretical and experimental results reveal that the typical perovskite photodetectors serve as an optical waveguide to confine and propagate the light, in which the long wavelength light propagates a longer distance; oppositely, the short wavelength light with the higher loss in devices fails to produce a photoresponse, owing to the wavelength dependent absorption of perovskite. This provides a new concept for designing narrowband photodetectors and will simulate new applications.

Large-Area Uniaxial-Oriented Growth of Free-Standing Thin Films at the Liquid-Air Interface with Millimeter-Sized Grains

Manipulating materials at the atomic scale and assembling them into macroscopic structures with controlled dimensionalities and single-crystal quality are grand scientific challenges. Here, we report a general solvent evaporation method to synthesize large-area uniaxial-oriented growth of free-standing thin films at the liquid-air interface. Crystals nucleate at the solution surface and rotate into the same orientation under electrostatic interaction and then merge as large crystals and grow laterally into a large-area uniform thin film with millimeter-sized grains. The lateral dimension is confined only by the size of containers. The film thickness can be tuned by adjusting solvent evaporation rate (R) and solute diffusivity (D), and a characteristic length, L * ∼ D R , was derived to estimate the film thickness. Molecular dynamic (MD) simulations reveal a concentration spike at the liquid-air interface during fast solvent evaporation, leading to the lateral growth of thin films. The large-area uniaxial oriented films are demonstrated on both inorganic metal halides and hybrid metal halide perovskites. The solvent evaporation approach and the determination of key parameters enabling film thickness prediction are beneficial to the high throughput and scalable production of single crystal-quality thin film materials under controlled evaporation conditions.

Visualizing the Surface Photocurrent Distribution in Perovskite Photovoltaics

Defect states play an important role in the photovoltaic performance of metal halide perovskites. Particularly, the passivation of surface defects has made great contributions to high-performance perovskite photovoltaics. This highlights the importance of understanding the surface defects from a fundamental level by developing more accurate and operando characterization techniques. Herein, a strategy to enable the surface carriers and photocurrent distributions on perovskite films to be visualized in the horizontal direction is put forward. The visual image of photocurrent distribution is realized by combining the static local distribution of carriers provided by scanning near-field optical microscopy with the dynamic transporting of carriers achieved via a scanning photocurrent measurement system. Taking a surface passivated molecule as an example, a comprehensive defect scene including static and dynamic as well as local and entire conditions is obtained using this strategy. The comprehensive analysis of the trap states in perovskite films is pioneered vertically and horizontally, which will powerfully promote the deep understanding of defect mechanisms and carrier behavior for the goal of fabricating high-performance perovskite optoelectronic devices.

A Bionic Interface to Suppress the Coffee-Ring Effect for Reliable and Flexible Perovskite Modules with a Near-90% Yield Rate

The inhomogeneity, poor interfacial contact, and pinholes caused by the coffee-ring effect severely affect the printing reliability of flexible perovskite solar cells (PSCs). Herein, inspired by the bio-glue of barnacles, a bionic interface layer (Bio-IL) of NiO_x /levodopa is introduced to suppress the coffee-ring effect during printing perovskite modules. The coordination effect of the sticky functional groups in Bio-IL can pin the three-phase contact line and restrain the transport of perovskite colloidal particles during the printing and evaporation process. Moreover, the sedimentation rate of perovskite precursor is accelerated due to the electrostatic attraction and rapid volatilization from an extraordinary wettability. The superhydrophilic Bio-IL affords an even spread over a large-area substrate, which boosts a complete and uniform liquid film for heterogeneous nucleation as well as crystallization. Perovskite films on different large-area substrates with negligible coffee-ring effect are printed. Consequently, inverted flexible PSCs and perovskite solar modules achieve a high efficiency of 21.08% and 16.87%, respectively. This strategy ensures a highly reliable reproducibility of printing PSCs with a near 90% yield rate.

Diammonium-Mediated Perovskite Film Formation for High-Luminescence Red Perovskite Light-Emitting Diodes

3D mixed-halide perovskite-based red emitters combine excellent charge-transport characteristics with simple solution processing and good film formation; however, light-emitting diodes (LEDs) based on these emitters cannot yet outperform their nanocrystal counterparts. Here the use of diammonium halides in regulating the formation of mixed bromide-iodide perovskite films is explored. It is found that the diammonium cations preferentially bond to Pb-Br, rather than Pb-I, octahedra, promoting the formation of quasi-2D phases. It is proposed that the perovskite formation is initially dominated by the crystallization of the thermodynamically more favorable 3D phase, but, as the solution gets depleted from the regular A cations, thin shells of amorphous quasi-2D perovskites form. This leads to crystalline perovskite grains with efficiently passivated surfaces and reduced lattice strain. As a result, the diammonium-treated perovskite LEDs demonstrate a record luminance (10745 cd m^-2 ) and half-lifetime among 3D perovskite-based red LEDs.

Perovskite Photo-Sensors with Solution-Processed TiO2 under Low Temperature Process and Ultra-Thin Polyethylenimine Ethoxylated as Electron Injection Layer

A perovskite photo-sensor is promising for a lightweight, thin, flexible, easy-to-coat fabrication process, and a higher incident photon-to-current conversion efficiency. We have investigated perovskite photo-sensors with a solution-processed compact TiO2 under a low-temperature process and an ultra-thin polyethylenimine ethoxylated (PEIE) as an electron injection layer. The TiO2 film is grown from an aqueous solution of titanium tetrachloride (TiCl4) at 70 °C by a chemical bath deposition method. For an alternative process, the ultra-thin PEIE is spin coated on the TiO2 film. Then, the perovskite layer is deposited on the substrate by the one- or two-step methods in the glovebox. Next, a hole transport layer of 2,2,7,7-tetrakis(N,N-di-p-methoxyphenylamine)-9, 9-spiro-bifluorene (Spiro-OMeTAD) solution is spin coated. The fabricated device structure is a photodiode structure of FTO/TiO2/(without or with) PEIE/(one- or two-step) perovskite layer/Spiro-OMeTAD/Au. For the sensing characteristics, a ratio of photo-to-dark-current density was 2.88 × 104 for the device with PEIE layer. In addition, a power-law relationship is discussed.

Solid-State Lithium-Ion Batteries as a Method for Doping Halide Perovskites with an In Situ Optical Readout of Dopant Concentration

Controlled doping of halide perovskites is a longstanding challenge for efficient optoelectronic applications. Here, a solid-state lithium-ion battery (LIB) inspired device is used as a method of extrinsically doping a halide perovskite in a controlled and measurable fashion. The Burstein-Moss band gap shift induced by the electronic doping is measured using in situ optical spectroscopy to monitor the fraction of injected charges that successfully n-type dope the perovskite. By comparing the optical and electrochemical readouts of the charge density, we demonstrate a 96% doping efficiency during the insertion process. Subsequent charge removal steps demonstrate only a partial "undoping" of the perovskite, providing insights into the capacity degradation pathways in perovskite LIB electrodes.

Centimeter-sized lead-free iodide-based hybrid double perovskite single crystals for efficient X-ray photoresponsivity

Hybrid organic-inorganic lead halide perovskites (HOIPs) possess significant photoelectric characteristics for solar energy conversion, but the presence of lead causes issues for eco-friendly applications. Halide double perovskites represent a green option for application in the optoelectronic field, especially X-ray detection systems. Despite the great efforts, the exploration of large-size lead-free iodide-based hybrid double perovskite single crystals for X-ray detection has been unsuccessful. Herein, we demonstrate that a large single crystal of the 2D (two-dimensional) semiconducting perovskite (C₆H₁₆N₂)₂CuBiI₈·0.5H₂O can serve as an X-ray detection candidate. A perovskite crystal, as large as 35 × 31 × 3 mm³, was grown using a low-cost, simple cooling solution approach. To the best of our knowledge, this is the first time a centimeter-sized 2D BiCu iodide double perovskite single crystal has been used for X-ray detection. The perovskite crystal exhibited unique properties for X-ray detection, such as a significant X-ray absorption coefficient, considerable μτ product, and low trap density. Moreover, X-ray detection with a sensitivity of 5.51 μC Gy_air^-1 cm^-2 was achieved based on a single crystal. This work opens new ways to explore specially designed organic cations for stabilizing 2D HOIPs that show great potential in optoelectronics.

Defect engineering in two-dimensional perovskite nanowire arrays by europium(III) doping towards high-performance photodetection

We demonstrate high-performance photodetectors based on Eu-doped 2D perovskite nanowire arrays. The pure crystallographic orientation enables efficient carrier transport and the doped Eu ions effectively suppress the trap density in the nanowire arrays. As a result, the optimized Eu-doped photodetectors show an excellent responsivity of 6.24 A W^-1, an outstanding specific detectivity of 5.83 × 10¹³ Jones and stable photo-switching behavior with a current on/off ratio of 10³.

Engineering van der Waals Materials for Advanced Metaphotonics

The outstanding chemical and physical properties of 2D materials, together with their atomically thin nature, make them ideal candidates for metaphotonic device integration and construction, which requires deep subwavelength light-matter interaction to achieve optical functionalities beyond conventional optical phenomena observed in naturally available materials. In addition to their intrinsic properties, the possibility to further manipulate the properties of 2D materials via chemical or physical engineering dramatically enhances their capability, evoking new science on light-matter interaction, leading to leaped performance of existing functional devices and giving birth to new metaphotonic devices that were unattainable previously. Comprehensive understanding of the intrinsic properties of 2D materials, approaches and capabilities for chemical and physical engineering methods, the resulting property modifications and novel functionalities, and applications of metaphotonic devices are provided in this review. Through reviewing the detailed progress in each aspect and the state-of-the-art achievement, insightful analyses of the outstanding challenges and future directions are elucidated in this cross-disciplinary comprehensive review with the aim to provide an overall development picture in the field of 2D material metaphotonics and promote rapid progress in this fast emerging and prosperous field.

Temperature-Dependent Luminescence and Anisotropic Optical Properties of Centimeter-Sized One-Dimensional Perovskite Trimethylammonium Lead Iodide Single Crystals

Low-dimensional hybrid halide perovskite materials with self-trapped exciton (STE) emissions and anisotropic properties are highly attractive for their great potential in many applications. However, to date, reports on large one-dimensional (1D) perovskite single crystals have been limited. Here, centimeter-sized 1D single crystals of trimethylammonium lead iodide (TMAPbI₃) with typical STE emission are synthesized by an antisolvent vapor-assisted crystallization method. Thermal quenching and antiquenching with a high relative sensitivity of photoluminescence (PL) are observed and studied via temperature-dependent photoluminescence spectroscopy. Further analysis indicates that the temperature-dependent PL behaviors are influenced by the self-trapping of the free exciton and the migrations between self-trapped excitons and intermediate nonradiative states. The TMAPbI₃ single crystal also exhibits a linearly polarized emission and a large birefringence that is higher than those of commercial birefringent crystals. This 1D perovskite with high structural anisotropy has promise for applications in versatile optical- and luminescence-related fields.

Aromatic Amino Acid-Mediated Perovskite Nanocrystals: Fluorescence Tuning and Morphological Evolution

Lead halide perovskites with high fluorescent and tunable morphology appeared at the forefront of materials chemistry because of their corresponding impressive optoelectronic properties. The current advancement of metal halide perovskites put forward the functional and bidentate ligand to expand their utilization in modified ligand chemistry. We successfully introduced nontoxic aromatic amino acid as a capping ligand to synthesize the perovskite nanocrystals (PNCs). The implementation of aromatic amino acid for the construction of CsPbX₃ nanocrystals (NCs) provides the synergetic service of the carboxylic and amine groups with the phenyl residue, which prompts the formation of NCs with high fluorescence intensity. The experimental results demonstrate the emissive property of PNCs in a whole visible region with long-term stability. Additionally, the morphology of the NCs has been tuned. We performed several characterization techniques to investigate the nature of the NCs in the solid and solution phases.

Accurate Adjusting the Lattice Strain of Triple-Cation and Mixed-Halide Perovskites for High-Performance Photodetector

The instability of perovskite optoelectronic devices remains a big barrier to their commercialization. The instability caused by external stimuli has been addressed by encapsulation, such as humidity, oxygen, heat, and ultraviolet light. However, the intrinsic instability of perovskite materials due to the lattice strain has not been fully addressed, which affects the physical properties and device performance to a great extent. Tuning the lattice strain by controlling the perovskite composition and ratio is an effective way to further develop efficient and stable devices. Herein, we prepare a series of triple-cation and mixed-halide (FAPbI₃)_x(MAPbBr₃)_y(CsPbI₃)_1-x-y perovskite single-crystal thin films and study the effect of lattice strain on the perovskite optoelectronic properties. Especially, the perovskite photodetector with a horizontal structure based on (FAPbI₃)_0.79(MAPbBr₃)_0.13(CsPbI₃)_0.08 single-crystal thin films exhibits excellent performance with an enhanced responsivity of 40 A/W, high detectivity of 1.9 × 10¹³ Jones, external quantum efficiency of 9100%, and superior stability. This can be explained by the fact that the optimal coordination between each element leads to the release of lattice strain and further produces low defect density and long carrier lifetime in (FAPbI₃)_0.79(MAPbBr₃)_0.13(CsPbI₃)_0.08 single-crystal thin films. This research shows the significance of ion ratios in tuning lattice strain and determining the intrinsic device performance and makes the perovskite (FAPbI₃)_0.79(MAPbBr₃)_0.13(CsPbI₃)_0.08 a promising candidate for the next generation of optoelectronic devices.

Electrically Modulated Near-Infrared/Visible Light Dual-Mode Perovskite Photodetectors

Dual-mode photodetectors (PDs) have attracted increasing interest owing to their potential optoelectrical applications. However, the widespread use of PDs is still limited by the high cost of epitaxial semiconductors. In contrast, the solution processability and wide spectral tunability of perovskites have led to the development of various inexpensive and high-performance optoelectronic devices. In this study, we develop a high-performance electronically modulated dual-mode PD with near-infrared (NIR) narrowband and visible light broadband detection based on organic-inorganic hybrid methylammonium lead halide perovskite (MAPbX₃; MA = CH₃NH₃ and X = Cl, Br, and I) single crystals with a pnp configuration. The operating mode of the dual-mode PD can be switched according to voltage bias polarity because the photon absorption region and carrier transport performance are tuned at different bias voltages. The dual-mode PD exhibits a NIR light responsivity of 0.244 A/W and a narrow full width at half-maximum of ∼12 nm at 820 nm at positive voltages and an average visible light responsivity of ∼0.13 A/W at negative voltages. The detectivities of both modes are high (∼10¹² Jones), and the linear dynamic range is wide (>100 dB). Our study provides a new method for fabricating multifunctional PDs and can expand their application in integrated imaging systems.

Exciton dynamics and photoresponse behavior of thein situannealed CsSnBr3perovskite films synthesized by thermal evaporation

The CsSnBr₃photodetectors are fabricated by thermal evaporation and 75 °Cin situannealing, and the effect ofin situannealing on the morphology, structure, exciton dynamics and photoresponse of thermally evaporated CsSnBr₃films are investigated. Especially, temperature dependent steady-state photoluminescence (PL) and transient PL decaying have been analyzed in details for understanding the exciton dynamics. Meanwhile, effect of annealing on the activation energy for trap sites (E_a), exciton binding energy (E_b), activation energy for interfacial trapped carriers (ΔE), trap densities and carriers mobilities are studied and the annealed (A-CsSnBr₃) reveals obviously lowerE_band trap density together with notably higher carrier mobility than those of the unannealed (UA-CsSnBr₃). Temperature dependence of the integrated PL intensity can be ascribed to the combining effect of the exciton dissociation, exciton quenching through trap sites and thermal activation of trapped carriers. The temperature dependent transient PL decaying analysis indicates that the PL decaying mechanism at low and high temperature is totally different from that in intermediate temperature range, in which combing effect of free exciton and localized state exciton decaying prevail. The beneficial effects of thein situannealing on the photoresponse performance of the CsSnBr₃films can be demonstrated by the remarkable enhancement of the optimal responsivity (R) afterin situannealing which increases from less than 1 A W^-1to 1350 A W^-1as well as dramatically improved noise equivalent power, specific detectivityD* and Gain (G).

Halide Perovskite Solar Cells for Building Integrated Photovoltaics: Transforming Building Façades into Power Generators

The rapid emergence of organic-inorganic lead halide perovskites for low-cost and high-efficiency photovoltaics promises to impact new photovoltaic concepts. Their high power conversion efficiencies, ability to coat perovskite layers on glass via various scalable deposition techniques, excellent optoelectronic properties, and synthetic versatility for modulating transparency and color allow perovskite solar cells (PSCs) to be an ideal solution for building-integrated photovoltaics (BIPVs), which transforms windows or façades into electric power generators. In this review, the unique features and properties of PSCs for BIPV application are accessed. Device engineering and optical management strategies of active layers, interlayers, and electrodes for semitransparent, bifacial, and colorful PSCs are also discussed. The performance of PSCs under conditions that are relevant for BIPV such as different operational temperature, light intensity, and light incident angle are also reviewed. Recent outdoor stability testing of PSCs in different countries and other demonstration of scalability and deployment of PSCs are also spotlighted. Finally, the current challenges and future opportunities for realizing perovskite-based BIPV are discussed.

Ultrafast transient infrared spectroscopy for probing trapping states in hybrid perovskite films

Studying the charge dynamics of perovskite materials is a crucial step to understand the outstanding performance of these materials in various fields. Herein, we utilize transient absorption in the mid-infrared region, where solely electron signatures in the conduction bands are monitored without external contributions from other dynamical species. Within the measured range of 4000 nm to 6000 nm (2500-1666 cm-1), the recombination and the trapping processes of the excited carriers could be easily monitored. Moreover, we reveal that within this spectral region the trapping process could be distinguished from recombination process, in which the iodide-based films show more tendencies to trap the excited electrons in comparison to the bromide-based derivatives. The trapping process was assigned due to the emission released in the mid-infrared region, while the traditional band-gap recombination process did not show such process. Various parameters have been tested such as film composition, excitation dependence and the probing wavelength. This study opens new frontiers for the transient mid-infrared absorption to assign the trapping process in perovskite films both qualitatively and quantitatively, along with the potential applications of perovskite films in the mid-IR region.

Defect Healing of MAPbI3 Perovskite Single Crystal Surface by Benzylamine

Controlling the surface traps in metal halide perovskites (MHPs) is essential for device performance, stability, and commercialization. Here, a facile approach is introduced to passivate the methylammonium lead iodide (MAPbI3) perovskite single crystal (PSC) surface defects by benzylamine (BA) ligand treatment, and the natural crystallographic (100) facets surface of PSC is chosen as the research platform to provide a deeper understanding of the passivation process. The confocal photoluminescence (PL) results show that the pristine three-dimensional (3D) MAPbI3 PSC surface with a symmetric emission spectrum is normally converted to a pure two-dimensional (2D) BA2PbI4, and also forms a quasi-2D Ruddlesden–Popper perovskite (RPP) BA2MAn−1PbnI3n+1 (n = 2, 3, 4, … ∞) after BA exchange with cation defects. The blue shift in the PL peak, as well as the extended exciton lifetimes of time-resolved photoluminescence (TRPL), indicate the realization of surface defect passivation. Additionally, changes in surface morphology are also investigated. The reaction starts with the formation of small, layered crystallites over the surface; as time elapses, the layered crystallites spread and merge in contact with each other, eventually resulting in smooth features. Our findings present a simple approach for MAPbI3 PSC surface defect passivation, which aims to advance MHP optimization processes toward practical perovskite device applications.

High-Throughput Evaluation of Emission and Structure in Reduced-Dimensional Perovskites

High-throughput experimentation (HTE) seeks to accelerate the exploration of materials space by uniting robotics, combinatorial methods, and parallel processing. HTE is particularly relevant to metal halide perovskites (MHPs), a diverse class of optoelectronic materials with a large chemical space. Here we develop an HTE workflow to synthesize and characterize light-emitting MHP single crystals, allowing us to generate the first reported data set of experimentally derived photoluminescence spectra for low-dimensional MHPs. We leverage the accelerated workflow to optimize the synthesis and emission of a new MHP, methoxy-phenethylammonium lead iodide ((4-MeO-PEAI)₂-PbI₂). We then synthesize 16 000 MHP single crystals and measure their photoluminescence to study the effects of synthesis parameters and compositional engineering on the emission intensity of 54 distinct MHPs: we achieve an acceleration factor of more than 100 times over previously reported HTE MHP synthesis and characterization methods. Using insights derived from this analysis, we screen an existing database for new, potentially emissive MHPs. On the basis of the Tanimoto similarity of the bright available emitters, we present our top candidates for future exploration. As a proof of concept, we use one of these (3,4-difluorophenylmethanamine) to synthesize an MHP which we find has a photoluminescence quantum yield of 10%.

Strongly Quantum-Confined Perovskite Nanowire Arrays for Color-Tunable Blue-Light-Emitting Diodes

Color tunability of perovskite light-emitting diodes (PeLEDs) by mixed halide compositional engineering is one of the primary intriguing characteristics of PeLEDs. However, mixed halide PeLEDs are often susceptible to color red-shifting caused by halide ion segregation. In this work, strongly quantum-confined perovskite nanowires (QPNWs) made of CsPbBr₃ are grown in nanoporous anodic alumina templates using a closed space sublimation process. By tuning the pore size with atomic layer deposition, QPNWs with a diameter of 6.6 to 2.8 nm have been successfully obtained, with continuous tunable photoluminescence emission color from green (512 nm) to pure blue (467 nm). To better understand the photophysics of QPNWs, carrier dynamics and the benefit of alumina passivation are studied and discussed in detail. Eventually, PeLEDs using various diameters of CsPbBr₃ QPNWs are successfully fabricated with cyan color (492 nm) PeLEDs, achieving a record high 7.1% external quantum efficiency (EQE) for all CsPbBr₃-based cyan color PeLEDs. Sky blue (481 nm) and pure blue (467 nm) PeLEDs have also been successfully demonstrated, respectively. The work here demonstrates a different approach to achieve quantum-confined one-dimensional perovskite structures and color-tunable PeLEDs, particularly blue PeLEDs.

Review for Rare-Earth-Modified Perovskite Materials and Optoelectronic Applications

In recent years, rare-earth metals with triply oxidized state, lanthanide ions (Ln³⁺), have been demonstrated as dopants, which can efficiently improve the optical and electronic properties of metal halide perovskite materials. On the one hand, doping Ln³⁺ ions can convert near-infrared/ultraviolet light into visible light through the process of up-/down-conversion and then the absorption efficiency of solar spectrum by perovskite solar cells can be significantly increased, leading to high device power conversion efficiency. On the other hand, multi-color light emissions and white light emissions originated from perovskite nanocrystals can be realized via inserting Ln³⁺ ions into the perovskite crystal lattice, which functioned as quantum cutting. In addition, doping or co-doping Ln³⁺ ions in perovskite films or devices can effectively facilitate perovskite film growth, tailor the energy band alignment and passivate the defect states, resulting in improved charge carrier transport efficiency or reduced nonradiative recombination. Finally, Ln³⁺ ions have also been used in the fields of photodetectors and luminescent solar concentrators. These indicate the huge potential of rare-earth metals in improving the perovskite optoelectronic device performances.

A Novel 4,4'-Bipiperidine-Based Organic Salt for Efficient and Stable 2D-3D Perovskite Solar Cells

The efficiency of metal halide perovskite solar cells (PSCs) has dramatically increased over the past decade (formerly 3.8%, now 25.5%). It has been widely demonstrated that the defects passivation of perovskite photo-active layer plays a vital role in increasing the efficiency and improving the stability of PSCs. In this study, we developed a novel 4,4'-bipiperidine (BiPi)-based organic salt with good stability and successfully introduced this ligand into perovskite for the first time. The embedded BiPi-based organic salt in the 3D perovskites facilitated the formation of two-dimensional-three-dimensional (2D-3D) perovskite materials that passivated the perovskite layer, with a constructive consequence in both photovoltaic performance and device stability. Incorporating this ligand improved the crystallinity of the perovskite materials with reduced defect states, prolonged resolved carrier lifetime, and improved stability. An optimized PSC device exhibited substantially improved device stability and an outstanding power conversion efficiency of 20.03%, with the aid of the BiPi-based organic salt [open-circuit voltage (V_OC), 1.10 V; current density (J_SC), 23.51 mA/cm²; and fill factor (FF), 0.77], which are 13.0% higher than the original device. Our study provides a ligand design protocol for developing next-generation, highly efficient, stable PSCs.

Recent advances in lead-free double perovskites for x-ray and photodetection

Over the last decade, lead halide perovskites have attracted significant research attention in the field of photovoltaics, light-emitting devices, photodetection, ionizing radiation detection, etc, owing to their outstanding optoelectrical properties. However, the commercial applications of lead-based perovskite devices are restricted due to the poor ambient stability and toxicity of lead. The encapsulation of lead-based devices can reduce the possible leakage of lead. However, it is hard to ensure safety during large-scale production and long-term storage. Recently, considerable efforts have been made to design lead-free perovskites for different optoelectronic applications. Metal halide double perovskites with the general formula of A₂M^IM^IIIX₆or A₂M^IVX₆could be potentially considered as green and stable alternatives for different optoelectronic applications. In this review article, we focus on the recent progress and findings on lead-free halide double perovskites for x-ray and UV-vis photodetection applications. Lead-free halide double perovskite has recently drawn a great deal of attention for superior x-ray detection due to its high absorption coefficient, large carrier mobility-lifetime product, and large bulk resistance. In addition, these materials exhibit good performance in photodetection in the UV-vis region due to high photocarrier generation and efficient carrier separation. In this review, first, we define the characteristics of lead-free double perovskite materials. The fundamental characteristics and beneficial properties of halide perovskites for direct and indirect x-ray detection are then discussed. We comprehensively review recent developments and efforts on lead-free double perovskite for x-ray detection and UV-vis photodetection. We bring out the current challenges and opportunities in the field and finally present the future outlook for developing lead-free double perovskite-based x-ray and UV-vis photodetectors for practical applications.

Unveiling the Valence State of Interstitial Bromine on Charge Carrier Lifetime in CH3NH3PbBr3 by Quantum Dynamics Simulation

Interstitial halogens are detrimental to the optoelectronic properties of metal halide perovskites. Using nonadiabatic (NA) molecular dynamics, we demonstrate that the valence state of interstitial bromine strongly changes the carrier lifetimes of MAPbBr₃ (MA = CH₃NH₃⁺). Both neutral and negatively charged interstitial bromine create no midgap states, and they decrease the bandgap, weaken the NA coupling, and accelerate decoherence in a different extent with respect to pristine MAPbBr₃, making free charge recombination either slow down about a 3-fold or remain largely unchanged. In contrast, a positively charged interstitial bromine forms a Br trimer and introduces a deep electron trap state, causing a 1.4-fold increase of charge recombination followed by a rapid electron trapping or across the bandgap because of an enhanced NA coupling. The simulations uncover the influence of different charged interstitial bromine defects on MAPbBr₃ carrier lifetimes and provide rational guidelines for optimizing perovskite solar cells.

Nanoscale Encapsulation of Hybrid Perovskites Using Hybrid Atomic Layer Deposition

Organic-inorganic hybrid perovskites have shown tremendous potential for optoelectronic applications. Ion migration within the crystal and across heterointerfaces, however, imposed severe problems with material degradation and performance loss in devices. Encapsulating hybrid perovskite with a thin physical barrier can be essential for suppressing the undesirable interfacial reactions without inhibiting the desirable transport of charge carriers. Here, we demonstrated that nanoscale, pinhole-free Al₂O₃ layer can be coated directly on the perovskite CH₃NH₃PbI₃ using atomic layer deposition (ALD). The success can be attributed to a multitude of strategies including surface molecular modification and hybrid ALD processing combining the thermal and plasma-enhanced modes. The Al₂O₃ films provided remarkable protection to the underlying perovskite films, surviving by hours in solvents without noticeable decays in either structural or optical properties. The results advanced the understanding of applying ALD directly on hybrid perovskite and provided new opportunities to implement stable and high-performance devices based on the perovskites.

Exciton-Phonon Coupling of Chiral One-Dimensional Lead-Free Hybrid Metal Halides at Room Temperature

The interaction between organic cations and inorganic metal halide octahedral units strongly affects the properties of organic-inorganic hybrid metal halides. The "soft" property of the lattice provides the possibility of its strong exciton-phonon interaction. Here we report one-dimensional (1D) lead-free chiral organic-inorganic hybrid metal halide single crystals of (R/S)-methylbenzylamine bismuth iodide (R/S-MBA)₂Bi₂I₈, which exhibits a high level of octahedral bond distortion. The introduction of chiral amines leads to a strong chiroptical response in the range of 200-600 nm. The strong exciton-phonon coupling can be observed through the coherent oscillation spectrum of transient absorption dynamics at room temperature. The coherent phonon oscillation frequencies are ∼97 and ∼130 cm^-1, corresponding to the symmetrical stretching or bending of the Bi-I octahedron. Our work provides new insights for the study of exciton-phonon coupling in 1D chiral hybrid metal halides.

Electrode Spacing as a Determinant of the Output Performance of Planar-Type Photodetectors Based on Methylammonium Lead Bromide Perovskite Single Crystals

Methylammonium lead bromide is a very perspective hybrid semiconductor material, suitable for high-sensitive, filter-free photodetection of electromagnetic radiation. Herein, we studied the effect of electrode spacing on the output performance and stability of planar-type photodetectors based on high-quality MAPbBr₃ single crystals. Such crystals, as large as 4.5×4.5×1.2 mm³ were synthesized via the inverse temperature crystallization method and were further used for the fabrication of planar Au/MAPbBr₃/Au photodetectors with variable electrode spacing (in the range between 125 and 25 μm). We report that the electrode spacing has a profound impact on photocurrent densities and key detector parameters (responsivity R, external quantum efficiency EQE, and specific detectivity D*). In the studied fivefold electrode spacing, the photocurrent density increased over 4 times, with decreasing active area of the devices. This effect is attributed to intrinsic photocurrent amplification. Based on the transient photocurrent measurements and calculated key parameters, we determined the device sample with the best output performance. The champion sample with an electrode spacing of 50 μm exhibited great detection ability, especially for a low light intensity of 200 nWcm^-2, for which we calculated the R of 19.55 A W^-1, EQE of 4253%, and D* of 3.42 × 10¹² Jones (cm Hz^1/2 W^-1). Moreover, the functional stability of this device showed a minimal reduction of photodetection ability after 2000 cycles, which makes it very promising for the next generation of optoelectronic devices.

Efficient and Stable Perovskite Solar Cells by B-Site Compositional Engineered All-Inorganic Perovskites and Interface Passivation

Perovskite solar cells (PSCs) have emerged as a cost-effective solar technology in the past years. PSCs by three-dimensional hybrid inorganic-organic perovskites exhibited decent power conversion efficiencies (PCEs); however, their stabilities were poor. On the other hand, PSCs by all-inorganic perovskites indeed exhibited good stability, but their PCEs were low. Here, the development of novel all-inorganic perovskites CsPbI₂Br:xNd³⁺, where Pb²⁺ at the B-site is partially heterovalently substituted by Nd³⁺, is reported. The CsPbI₂Br:xNd³⁺ thin films possess enlarged crystal sizes, enhanced charge carrier mobilities, and superior crystallinity. Thus, the PSCs by the CsPbI₂Br:xNd³⁺ thin films exhibit more than 20% enhanced PCEs and dramatically boosted stability compared to those based on pristine CsPbI₂Br thin films. To further boost the device performance of PSCs, solution-processed 4-lithium styrenesulfonic acid/styrene copolymer (LiSPS) is utilized to passivate the surface defect and suppress surface charge carrier recombination. The PSCs based on the CsPbI₂Br:xNd³⁺/LiSPS bilayer thin film possess reduced charge extraction lifetime and suppressed charge carrier recombination, resulting in 14% enhanced PCEs and significantly boosted stability compared to those without incorporation of the LiSPS interface passivation layer. All these results indicate that we developed a facile way to approach high-performance PSCs by all-inorganic perovskites.

Autonomous Reconstitution of Fractured Hybrid Perovskite Single Crystals

The outstanding performance and facile processability turn hybrid organic-inorganic perovskites into one of the most sought-after classes of semiconducting materials for optoelectronics. Yet, their translation into real-world applications necessitates that challenges with their chemical stability and poor mechanical robustness are first addressed. Here, centimeter-size single crystals of methylammoniumlead(II) iodide (MAPbI₃ ) are reported to be capable of autonomous self-healing under minimal compression at ambient temperature. When crystals are halved and the fragments are brought in contact, they can readily self-repair as a result of a liquid-like behavior of their lattice at the contact surface, which leads to a remarkable healing with an efficiency of up to 82%. The successful reconstitution of the broken single crystals is reflected in recuperation of their optoelectronic properties. Testing of the healed crystals as photodetectors shows an impressive 74% recovery of the generated photocurrent relative to pristine crystals. This self-healing capability of MAPbI₃ single crystals is an efficient strategy to overcome the poor mechanical properties and low wear resistance of these materials, and paves the way for durable and stable optoelectronic devices based on single crystals of hybrid perovskites.

In Situ Inorganic Ligand Replenishment Enables Bandgap Stability in Mixed-Halide Perovskite Quantum Dot Solids

Instability in mixed-halide perovskites (MHPs) is a key issue limiting perovskite solar cells and light-emitting diodes (LEDs). One form of instability arises during the processing of MHP quantum dots using an antisolvent to precipitate and purify the dots forming surface traps that lead to decreased luminescence, compromised colloidal stability, and emission broadening. Here, the introduction of inorganic ligands in the antisolvents used in dot purification is reported in order to overcome this problem. MHPs that are colloidally stable for over 1 year at 25 °C and 40% humidity are demonstrated and films that are stable under 100 W cm^-2 photoirradiation, 4× longer than the best previously reported MHPs, are reported. In LEDs, the materials enable an EQE of 24.4% (average 22.5 ± 1.3%) and narrow emission (full-width at half maximum of 30 nm). Sixfold-enhanced operating stability relative to the most stable prior red perovskite LEDs having external quantum efficiency >20% is reported.

Anion-Exchange Driven Phase Transition in CsPbI3 Nanowires for Fabricating Epitaxial Perovskite Heterojunctions

Anion-exchange in halide perovskites provides a unique pathway of bandgap engineering for fabricating heterojunctions in low-cost photovoltaics and optoelectronics. However, it remains challenging to achieve robust and sharp perovskite heterojunctions, due to the spontaneous anion interdiffusion across the heterojunction in 3D perovskites. Here, it is shown that the anionic behavior in 1D perovskites is fundamentally different, that the anion exchange can readily drive an indirect-to-direct bandgap phase transition in CsPbI₃ nanowires (NWs) and greatly lower the phase transition temperature. In addition, the heterojunction created by phase transition is epitaxial in nature, and its chemical composition can be precisely controlled upon postannealing. Further study of the phase transition dynamics reveals a threshold-dominating anion exchange mechanism in these 1D NWs rather than the gradient-dominating mechanism in 3D systems. The results provide important insights into the ionic behavior in halide perovskites, which is beneficial for applications in solar cells, light-emitting diodes (LEDs), and other semiconductor devices.

Controllable Acceleration and Deceleration of Charge Carrier Transport in Metal-Halide Perovskite Single-Crystal by Cs-Cation Induced Bandgap Engineering

Charge carrier transport in materials is of essential importance for photovoltaic and photonic applications. Here, the authors demonstrate a controllable acceleration or deceleration of charge carrier transport in specially structured metal-alloy perovskite (MACs)PbI₃ (MA= CH₃ NH₃ ) single-crystals with a gradient composition of CsPbI₃ /(MA_{1- x} Cs_x )PbI₃ /MAPbI₃ . Depending on the Cs-cation distribution in the structure and therefore the energy band alignment, two different effects are demonstrated: i) significant acceleration of electron transport across the depth driven by the gradient band alignment and suppression of electron-hole recombination, benefiting for photovoltaic and detector applications; and ii) decelerated electron transport and thus improved radiative carrier recombination and emission efficiency, highly beneficial for light and display applications. At the same time, the top Cs-layer results in hole localization in the top layer and surface passivation. This controllable acceleration and deceleration of electron transport is critical for various applications in which efficient electron-hole separation and suppressed nonradiative electron-hole recombination is demanded.

A First-Principles Study on the Structural and Carrier Transport Properties of Inorganic Perovskite CsPbI3 under Pressure

Lead halide perovskite has attracted intensive attention for pressure and strain detection. Principally, pressure-induced changes in the structure and resistance of perovskite may bring great potential for developing high-performance piezoresistive pressure sensors. Herein, for the first time, we study the structural changes and the hot carrier cooling process of perovskite CsPbI3 under pressure based on density functional theory and time-dependent density functional theory. The calculation results show that the lattice constant of CsPbI3 linearly decreases and the time and path of the hot carrier cooling process change apparently under pressure. Meanwhile, the pressure will change the transition dipole moment, and the position of the k-point will not affect the optical properties of perovskite. Subsequently, the electrical conductivity enlarges as the pressure increases due to the change in charge density caused by pressure, which will be helpful for its potential application in the pressure sensors.

In Situ Growth Mechanism for High-Quality Hybrid Perovskite Single-Crystal Thin Films with High Area to Thickness Ratio: Looking for the Sweet Spot

The development of in situ growth methods for the fabrication of high-quality perovskite single-crystal thin films (SCTFs) directly on hole-transport layers (HTLs) to boost the performance of optoelectronic devices is critically important. However, the fabrication of large-area high-quality SCTFs with thin thickness still remains a significant challenge due to the elusive growth mechanism of this process. In this work, the influence of three key factors on in situ growth of high-quality large-size MAPbBr₃ SCTFs on HTLs is investigated. An optimal "sweet spot" is determined: low interface energy between the precursor solution and substrate, a slow heating rate, and a moderate precursor solution concentration. As a result, the as-obtained perovskite SCTFs with a thickness of 540 nm achieve a record area to thickness ratio of 1.94 × 10⁴  mm, a record X-ray diffraction peak full width at half maximum of 0.017°, and an ultralong carrier lifetime of 1552 ns. These characteristics enable the as-obtained perovskite SCTFs to exhibit a record carrier mobility of 141 cm² V^-1 s^-1 and good long-term structural stability over 360 days.

Highly Orientational Order Perovskite Induced by In situ-generated 1D Perovskitoid for Efficient and Stable Printable Photovoltaics

Employing low-dimensional perovskite has been proven to be a promising approach to enhance the efficiency and stability of perovskite solar cells. Here, thiopheniformamidine hydrochloride is introduced into CH₃ NH₃ PbI₃ -based printable mesoscopic perovskite solar cells, to form 1D iodide lead thiophenamidine (TFPbI₃ ) in situ. This judiciously designed low-dimensional perovskite can effectively passivate the defect of perovskite and induce the perovskite crystals to grow in a direction perpendicular to the substrate. Thus, the obtained 1D@3D perovskite could suppress the charge recombination and promote the charge transfer significantly. Benefiting from its dual effect and robustness, a significantly improved power conversion efficiency of 17.42% is yielded. The authors also develop high-performance printable mesoscopic perovskite solar cells with a champion efficiency approaching 13% for aperture area about 11.8 cm² , as well as outstanding operational stability, retaining 90% of the original power conversion efficiency after 1000 hours of continuous illumination at the maximum power point in air.

Quantifying Efficiency Limitations in All-Inorganic Halide Perovskite Solar Cells

While halide perovskites have excellent optoelectronic properties, their poor stability is a major obstacle toward commercialization. There is a strong interest to move away from organic A-site cations such as methylammonium and formamidinium toward Cs with the aim of improving thermal stability of the perovskite layers. While the optoelectronic properties and the device performance of Cs-based all-inorganic lead-halide perovskites are very good, they are still trailing behind those of perovskites that use organic cations. Here, the state-of-the-art of all-inorganic perovskites for photovoltaic applications is reviewed by performing detailed meta-analyses of key performance parameters on the cell and material level. Key material properties such as carrier mobilities, external photoluminescence quantum efficiency, and photoluminescence lifetime are discussed and what is known about defect tolerance in all-inorganic is compared relative to hybrid (organic-inorganic) perovskites. Subsequently, a unified approach is adopted for analyzing performance losses in perovskite solar cells based on breaking down the losses into several figures of merit representing recombination losses, resistive losses, and optical losses. Based on this detailed loss analysis, guidelines are eventually developed for future performance improvement of all-inorganic perovskite solar cells.

Is There a Polaron Signature in Angle-Resolved Photoemission of CsPbBr_{3}?

The formation of large polarons has been proposed as reason for the high defect tolerance, low mobility, low charge carrier trapping, and low nonradiative recombination rates of lead halide perovskites. Recently, direct evidence for large-polaron formation has been reported from a 50% effective mass enhancement in angle-resolved photoemission of CsPbBr_{3} over theory for the orthorhombic structure. We present in-depth band dispersion measurements of CsPbBr_{3} and GW calculations, which lead to similar effective masses at the valence band maximum of 0.203±0.016 m_{0} in experiment and 0.226 m_{0} in orthorhombic theory. We argue that the effective mass can be explained solely on the basis of electron-electron correlation and large-polaron formation cannot be concluded from photoemission data.

In Situ Polymer Network in Perovskite Solar Cells Enabled Superior Moisture and Thermal Resistance

Perovskite decomposition arising from water permeation and heat induced crystal expansion is a major obstacle restricting the long-term durability of perovskite solar cells (PSCs). Herein, a polymerizable methyl acrylate (MCE) was employed as dopants in the deposition of perovskite thin films. Owing to the in situ formed polymer network, the environment moisture can be retained on the perovskite surface as the formation of a thin layer of perovskite monohydrate to prevent their deep penetration and transverse spread, and the heat tolerance of the perovskite was also improved because of the anchor structure between Pb²⁺ and -C═O groups and the agglomeration effect of the polymerized MCE. Moreover, MCE can coordinate with Pb²⁺ ions and some of them were volatilized during crystallization, resulting in preferred crystal orientations and suppressed nonradiative recombination. As a result, an excellent efficiency up to 21% with improved stability of MAPbI₃ PSC was achieved.

High-Luminance Microsized CH3NH3PbBr3 Single-Crystal-Based Light-Emitting Diodes via a Facile Liquid-Insulator Bridging Route

Micro-/nanosized organic-inorganic hybrid perovskite single crystals (SCs) with appropriate thickness and high crystallinity are promising candidates for high-performance electroluminescent (EL) devices. However, their small lateral size poses a great challenge for efficient device construction and performance optimization, causing perovskite SC-based light-emitting diodes (PSC-LEDs) to demonstrate poor EL performance. Here, we develop a facile liquid-insulator bridging (LIB) strategy to fabricate high-luminance PSC-LEDs based on single-crystalline CH₃NH₃PbBr₃ microflakes. By introducing a blade-coated poly(methyl methacrylate) (PMMA) insulating layer to effectively overcome the problems of leakage current and possible short circuits between electrodes, we achieve the reliable fabrication of PSC-LEDs. The LIB method also allows us to systematically boost the device performance through crystal growth regulation and device architecture optimization. Consequently, we realize the best CH₃NH₃PbBr₃ microflake-based PSC-LED with an ultrahigh luminance of 136100 cd m^-2 and a half-lifetime of 88.2 min at an initial luminance of ∼1100 cd m^-2, which is among the highest for organic-inorganic hybrid perovskite LEDs reported to date. Moreover, we observe the strong polarized edge emission of the microflake-based PSC-LEDs with a high degree of polarization up to 0.69. Our work offers a viable approach for the development of high-performance perovskite SC-based EL devices.

Spray deposited polycrystalline MAPbBr3 thick films for hole-transport-material free solar cells

A spray deposition procedure for the fabrication of polycrystalline MAPbBr₃ thick films (20-100 μm) is developed and highly efficient (>5.5% under AM1.5 sunlight) hole-transport-material free perovskite solar cells are successfully made with 40 μm thick MAPbBr₃ films.

Recent Advances on the Strategies to Stabilize the α-Phase of Formamidinium Based Perovskite Materials

Perovskite solar cells (PSC) are considered promising next generation photovoltaic devices due to their low cost and high-power conversion efficiency (PCE). The perovskite material in the photovoltaic devices plays the fundamental role for the unique performances of PSC. Formamidinium based perovskite materials have become a hot-topic for research due to their excellent characteristics, such as a lower band gap (1.48 V), broader light absorption, and better thermal stability compared to methylammonium based perovskite materials. There are four phases of perovskite materials, named the cubic α-phase, tetragonal β-phase, orthorhombic γ-phase, and δ-phase (yellow). Many research focus on the transition of α-phase and δ-phase. α-Phase FA-based perovskite is very useful for photovoltaic application. However, the phase stability of α-phase FA-based perovskite materials is quite poor. It transforms into its useless δ-phase at room temperature. This instability will lead the degradation of PCE and the other optoelectronic properties. For the practical application of PSC, it is urgent to understand more about the mechanism of this transformation and boost the stability of α-Phase FA-based perovskite materials. This review describes the strategies developed in the past several years, such as mixed cations, anion exchange, dimensions controlling, and surface engineering. These discussions present a perspective on the stability of α-phase of FA-based perovskite materials and the coming challenges in this field.