Characterization of coliphage PR772 and evaluation of its use for virus filter performance testing

Virus inactivation by sequential ultraviolet-chlorine disinfection: Synergistic effect and mechanism

The COVID-19 outbreak has raised concerns about the efficacy of the disinfection process followed in water treatment plants in preventing the spread of viruses. Ultraviolet (UV) and chlorine multi-barrier disinfection processes are commonly used in water treatment plants; however, their effects on virus inactivation are still unclear. In this study, the effects of different disinfection processes (i.e., UV, free chlorine, and their combination) on waterborne viruses were analyzed using bacteriophage surrogates (i.e., MS2 and PR772) as alternative indicators. The results showed that the inactivation rates of PR772 by either UV or free chlorine disinfection were higher than those of MS2. PR772 was approximately 1.5 times more sensitive to UV disinfection and 8.4 times more sensitive to chlorine disinfection than MS2. Sequential UV-chlorine disinfection had a synergistic effect on virus inactivation, which was enhanced by an increase in the UV dose. As compared with single free chlorine disinfection, UV irradiation at 40 mJ cm^-2 enhanced MS2 and PR772 inactivation significantly with a 2.7-fold (MS2) and a 1.7-fold (PR772) increase in the inactivation rate constants on subsequent chlorination in phosphate buffered saline. The synergistic effect was also observed in real wastewater samples, in which the MS2 inactivation rate increased 1.4-fold on subsequent chlorination following UV irradiation at 40 mJ cm^-2. The mechanism of the synergistic effect of sequential UV-chlorine disinfection was determined via sodium dodecyl sulfate-polyacrylamide gel electrophoresis, using MS2 as an indicator. The results showed that the synergistic effect was due to damage to MS2 surface proteins caused by previous UV disinfection, which enhanced the sensitivity of MS2 to chlorination. This study provides a feasible approach for the efficient inactivation of viruses in water supply and drainage.

Assessment of potential for viral contamination of user and environment via aerosols generated during hand drying: A pilot study

Background

Hand drying is an essential step of hand hygiene, helping remove microbes remaining on hands following handwashing. However, it is unclear whether particles dispersed or aerosolized during hand drying can also have an impact on microbe dissemination and so pose an infection risk.

Methods

We used a PR772 bacteriophage to investigate whether microorganisms remaining on hands can disperse in the washroom environment and contaminate facemasks of others sharing the same space, as a surrogate for virus inhalation risk. Hand drying using either a jet air dryer or paper towels were performed, and mask contamination by splattering and droplet deposition was investigated, up to 15 min following each procedure.

Results

Facemask contamination by splattering was 10-fold higher when a jet air dryer was used, compared with hand drying by paper towels, for both the person performing the hand drying and for standby users stationed at 1 and 2 m distance. Facemask contamination by droplet/aerosols deposition was higher in the first 5 min following hand drying, for both methods; however, virus load was significantly higher when a jet air dryer was used. In the jet air dryer assays, facemask contamination increased at 15 min post-hand drying, suggesting aerosolization of small particles that remain airborne for longer.

Conclusion

When using a jet air dryer, virus contamination dispersed further and for a longer period of time (up to 15 min post hand-drying). The method chosen for hand drying can potentially impact the airborne dissemination of microbial pathogens, including respiratory virus, and so potentially increase the risk of exposure and infection for other washroom users.

Electrospun Nanofibrous Membranes for Controlling Airborne Viruses: Present Status, Standardization of Aerosol Filtration Tests, and Future Development

The global COVID-19 pandemic has raised great public concern about the airborne transmission of viral pathogens. Virus-laden aerosols with small size could be suspended in the air for a long duration and remain infectious. Among a series of measures implemented to mitigate the airborne spread of infectious diseases, filtration by face masks, respirators, and air filters is a potent nonpharmacologic intervention. Compared with conventional air filtration media, nanofibrous membranes fabricated via electrospinning are promising candidates for controlling airborne viruses due to their desired characteristics, i.e., a reduced pore size (submicrometers to several micrometers), a larger specific surface area and porosity, and retained surface and volume charges. So far, a wide variety of electrospun nanofibrous membranes have been developed for aerosol filtration, and they have shown excellent filtration performance. However, current studies using electrospinning for controlling airborne viruses vary significantly in the practice of aerosol filtration tests, including setup configurations and operations. The discrepancy among various studies makes it difficult, if not impossible, to compare filtration performance. Therefore, there is a pressing need to establish a standardized protocol for evaluating the electrospun nanofibrous membranes' performance for removing viral aerosols. In this perspective, we first reviewed the properties and performance of diverse filter media, including electrospun nanofibrous membranes, for removing viral aerosols. Next, aerosol filtration protocols for electrospun nanofibrous membranes were discussed with respect to the aerosol generation, filtration, collection, and detection. Thereafter, standardizing the aerosol filtration test system for electrospun nanofibrous membranes was proposed. In the end, the future advancement of electrospun nanofibrous membranes for enhanced air filtration was discussed. This perspective provides a comprehensive understanding of status and challenges of electrospinning for air filtration, and it sheds light on future nanomaterial and protocol development for controlling airborne viruses, preventing the spread of infectious diseases, and beyond.

Are carbon water filters safe for private wells? Evaluating the occurrence of microbial indicator organisms in private well water treated by point-of-use activated carbon block filters

Point-of-use (POU) water treatment is highly relevant to private well users vulnerable to chemical contamination, but uncertainty remains around the effects of activated carbon based POU devices on the microbial quality of the treated water. In this study, under-sink activated carbon block water filters were installed in 17 homes relying on private well water in North Carolina. The influent and effluent water in each home was evaluated for bacterial and viral microbial indicator organisms monthly for five months. Multiple logistic regression was used to identify water quality and water usage variables that were significant predictors of each indicator organism occurring in the filter effluent. The odds of total coliforms occurring in the effluent decreased by 84% with each 1-log₁₀ increase in the influent HPC (p < 0.05), suggesting a protective effect by native heterotrophic bacteria, but increased by over 50 times with low cumulative water use (p < 0.05). The filters were not protective against coliphages in the influent and viral shedding may occur after periods of increased virus concentrations in the raw well water. Specific bacteria were also found to increase in the effluent, causing a shift in the bacterial community composition, although potential opportunistic pathogens were detected in both the influent and the effluent. Overall, under normal conditions of use, the filters tested in this study did not represent a significant additional risk for well users beyond the existing exposures from undisinfected well water alone.

Air filtration as a tool for the reduction of viral aerosols

For testing the effectiveness of air purification devices in regard to the reduction of virus-containing aerosols, a test method involving test viruses has been lacking until now. The use of bacteriophages (phiX174 phages) is a method to test the efficiency of air purification devices under experimental conditions. Using air purifiers with a HEPA filter H14, a 4.6-6.1 Log reduction of test viruses can be achieved if bacteriophages are directly aerosolised into the air purifier, which corresponds to a reduction of 99.9974-99.9999%. Due to the complexity and individuality of air flow, an experimental approach was used in which all outside influences were minimised. The experimental setup was practical and chosen to project a scenario of direct transmission by an emitting source to a recipient. The experiments were performed with and without the air purifier at a distance of 0.75 m and 1.5 m each. Using the air purifier at a setting of 1000 m³/h, the concentration of the phiX174 phages in the air could be reduced by 2.86 Log (mean value). Nevertheless, the experiments without the air purifier showed a similar reduction rate of 2.61 Log (mean value) after 35 min. The concentration of phiX174 phages in the air could be additionally reduced up to 1 log step (maximum value) by the use of the air purifier in comparison to the experiments without. Distance was shown to be an important factor for risk reduction.

Virus Isoelectric Point Estimation: Theories and Methods

Much of virus fate, both in the environment and in physical/chemical treatment, is dependent on electrostatic interactions. Developing an accurate means of predicting virion isoelectric point (pI) would help to understand and anticipate virus fate and transport, especially for viruses that are not readily propagated in the lab. One simple approach to predicting pI estimates the pH at which the sum of charges from ionizable amino acids in capsid proteins approaches zero. However, predicted pIs based on capsid charges frequently deviate by several pH units from empirically measured pIs. Recently, the discrepancy between empirical and predicted pI was attributed to the electrostatic neutralization of predictable polynucleotide-binding regions (PBRs) of the capsid interior. In this paper, we review models presupposing (i) the influence of the viral polynucleotide on surface charge or (ii) the contribution of only exterior residues to surface charge. We then compare these models to the approach of excluding only PBRs and hypothesize a conceptual electrostatic model that aligns with this approach. The PBR exclusion method outperformed methods based on three-dimensional (3D) structure and accounted for major discrepancies in predicted pIs without adversely affecting pI prediction for a diverse range of viruses. In addition, the PBR exclusion method was determined to be the best available method for predicting virus pI, since (i) PBRs are predicted independently of the impact on pI, (ii) PBR prediction relies on proteome sequences rather than detailed structural models, and (iii) PBR exclusion was successfully demonstrated on a diverse set of viruses. These models apply to nonenveloped viruses only. A similar model for enveloped viruses is complicated by a lack of data on enveloped virus pI, as well as uncertainties regarding the influence of the phospholipid envelope on charge and ion gradients.

Mechanistic insights into viral clearance during the chromatography steps in antibody processes by using virus surrogates

Viral safety is required for biological products to treat human diseases, and the burden of inactivation and or virus removal lies on the downstream purification process. Minute virus of mice (MVM) is a nonenveloped parvovirus commonly used as the worst-case model virus in validation studies because of its small size and high chemical stability. In this study, we investigated the use of MVM-mock virus particle (MVP) and bacteriophage ΦX174 as surrogates for MVM to mimic viral clearance studies, with a focus on chromatography operations. Based on structural models and comparison of log reduction value among MVM, MVP, and ΦX174, it was demonstrated that MVP can be used as a noninfectious surrogate to assess viral clearance during process development in multiple chromatography systems in a biosafety level one (BSL-1) laboratory. Protein A (ProA) chromatography was investigated to strategically assess the impact of the resin, impurities, and the monoclonal antibody product on virus removal.

Using Algal Virus Paramecium bursaria Chlorella Virus as a Human Adenovirus Surrogate for Validation of UV Treatment Systems

Adenovirus is among the most UV-resistant waterborne human pathogens. There is a need to identify nonpathogenic surrogates for adenovirus for the water treatment industry. In this study, the feasibility of using the algal virus Paramecium bursaria chlorella virus (PBCV-1) as an adenovirus surrogate for validation of UV reactors was evaluated. The UV dose-response behavior of PBCV-1 to monochromatic UV radiation at 254 nm and action spectrum for wavelengths ranging from 214 to 289 nm were measured. A culture-based infectivity assay was used to evaluate viral inactivation, and a quantitative PCR assay was used to quantify DNA damage. A UV₂₅₄ dose of 150 mJ/cm² resulted in roughly 5-log₁₀ units of reduction of PBCV-1, which is similar to that of adenovirus. Furthermore, the inactivation action spectrum of PBCV-1 was similar to that of adenovirus between 214 and 289 nm. A simplified and inexpensive prepurification method was also developed to prepare PBCV-1 viral suspensions with similar inactivation behavior to purified PBCV-1. Overall, PBCV-1 appears to represent an appropriate adenovirus surrogate for UV system performance evaluation and illustrates the potential of using algal viruses as nonpathogenic, easy to culture, and readily available surrogates for human pathogens.

Ozone efficacy for the control of airborne viruses: Bacteriophage and norovirus models

This study was designed to test the efficacy of an air treatment using ozone and relative humidity (RH) for the inactivation of airborne viruses. Four phages (φX174, PR772, MS2 and φ6) and one eukaryotic virus (murine norovirus MNV-1) were exposed to low ozone concentrations (1.23 ppm for phages and 0.23 ppm for MNV-1) and various levels of RH for 10 to 70 minutes. The inactivation of these viruses was then assessed to determine which of the tested conditions provided the greatest reduction in virus infectivity. An inactivation of at least two orders of magnitude for φX174, MS2 and MNV-1 was achieved with an ozone exposure of 40 minutes at 85% RH. For PR772 and φ6, exposure to the reference condition at 20% RH for 10 minutes yielded the same results. These findings suggest that ozone used at a low concentration is a powerful disinfectant for airborne viruses when combined with a high RH. Air treatment could therefore be implemented inside hospital rooms ventilated naturally.

Electron cryo-microscopy of bacteriophage PR772 reveals the elusive vertex complex and the capsid architecture

Bacteriophage PR772, a member of the Tectiviridae family, has a 70 nm diameter icosahedral protein capsid that encapsulates a lipid membrane, dsDNA, and various internal proteins. An icosahedrally averaged CryoEM reconstruction of the wild-type virion and a localized reconstruction of the vertex region reveal the composition and the structure of the vertex complex along with new protein conformations that play a vital role in maintaining the capsid architecture of the virion. The overall resolution of the virion is 2.75 Å, while the resolution of the protein capsid is 2.3 Å. The conventional penta-symmetron formed by the capsomeres is replaced by a large vertex complex in the pseudo T = 25 capsid. All the vertices contain the host-recognition protein, P5; two of these vertices show the presence of the receptor-binding protein, P2. The 3D structure of the vertex complex shows interactions with the viral membrane, indicating a possible mechanism for viral infection.

Evaluating the effect of in-process material on the binding mechanisms of surrogate viral particles to a multi-modal anion exchange resin

Bacteriophage binding mechanisms to multi-modal anion exchange resin may include both anion exchange and hydrophobic interactions, or the mechanism can be dominated by a single moiety. However, previous studies have reported binding mechanisms defined for simple solutions containing only buffer and a surrogate viral spike (i.e. bacteriophage ΦX174, PR772, and PP7). We employed phage spiked in-process monoclonal antibody (mAb) pools to model binding under bioprocessing conditions. These experiments allow the individual contributions of the mAb, in-process impurities, and buffer composition on mechanistic removal of phages to be studied. PP7 and PR772 use synergetic binding by the positively charged quaternary amine and the hydrophobic aromatic phenyl group to bind multi-modal resin. ΦX174's binding mechanism remains inconclusive due to operating conditions.

Bacteriophages as indicators of faecal pollution and enteric virus removal

Bacteriophages are an attractive alternative to faecal indicator bacteria (FIB), particularly as surrogates of enteric virus fate and transport, due to their closer morphological and biological properties. Based on a review of published data, we summarize densities of coliphages (F+ and somatic), Bacteroides spp. and enterococci bacteriophages (phages) in individual human waste, raw wastewater, ambient fresh and marine waters and removal through wastewater treatment processes utilizing traditional treatments. We also provide comparisons with FIB and enteric viruses whenever possible. Lastly, we examine fate and transport characteristics in the aquatic environment and provide an overview of the environmental factors affecting their survival. In summary, concentrations of bacteriophages in various sources were consistently lower than FIB, but more reflective of infectious enteric virus levels. Overall, our investigation indicates that bacteriophages may be adequate viral surrogates, especially in built systems, such as wastewater treatment plants.

SIGNIFICANCE AND IMPACT OF THE STUDY

Bacteriophage are alternative fecal indicators that may be better surrogates for viral pathogens than fecal indicator bacteria (FIB). This report offers a summary of the existing literature concerning the utility of bacteriophage as indicators of viral presence (fecal sources and surface waters) and persistence (in built infrastructure and aquatic environments). Our findings indicate that bacteriophage levels in all matrices examined are consistently lower than FIB, but similar to viral pathogens. Furthermore, in built infrastructure (e.g. wastewater treatment systems) bacteriophage closely mimic viral pathogen persistence suggesting they may be adequate sentinels of enteric virus removal.

Characterization of Non-Infectious Virus-Like Particle Surrogates for Viral Clearance Applications

Viral clearance is a critical aspect of biopharmaceutical manufacturing process validation. To determine the viral clearance efficacy of downstream chromatography and filtration steps, live viral "spiking" studies are conducted with model mammalian viruses such as minute virus of mice (MVM). However, due to biosafety considerations, spiking studies are costly and typically conducted in specialized facilities. In this work, we introduce the concept of utilizing a non-infectious MVM virus-like particle (MVM-VLP) as an economical surrogate for live MVM during process development and characterization. Through transmission electron microscopy, size exclusion chromatography with multi-angle light scattering, chromatofocusing, and a novel solute surface hydrophobicity assay, we examined and compared the size, surface charge, and hydrophobic properties of MVM and MVM-VLP. The results revealed that MVM and MVM-VLP exhibited nearly identical physicochemical properties, indicating the potential utility of MVM-VLP as an accurate and economical surrogate to live MVM during chromatography and filtration process development and characterization studies.

Resistance of Aerosolized Bacterial Viruses to Four Germicidal Products

Viral diseases can spread through a variety of routes including aerosols. Yet, limited data are available on the efficacy of aerosolized chemicals to reduce viral loads in the air. Bacteriophages (phages) are often used as surrogates for hazardous viruses in aerosol studies because they are inexpensive, easy to handle, and safe for laboratory workers. Moreover, several of these bacterial viruses display physical characteristics similar to pathogenic human and animal viruses, like morphological size, type of nucleic acids, capsid morphology, and the presence of an envelope. In this study, the efficacy of four chemicals was evaluated on four airborne phages at two different relative humidity levels. Non-tailed bacteriophages MS2 (single-stranded RNA), ϕ6 (double-stranded RNA, enveloped), PR772 (double-stranded DNA), and ϕX174 (single-stranded DNA) were first aerosolized in a 55L rotative environmental chamber at 19°C with 25% and 50% relative humidity. Then, hydrogen peroxide, Eugenol (phenylpropene used in commercial perfumes and flavorings), Mist® (automobile disinfectant containing Triethylene glycol), and Pledge® (multisurface disinfectant containing Isopropanol, n-Alkyl Dimethyl Benzyl Amonium Chlorides, and n-Alkyl Dimethyl Ethylbenzyl Ammonium Chloride) were nebulized with the phages using a separate nebulizer. Aerosols were maintained in suspension during 10 minutes, 1 hour, and 2 hours. Viral aerosols were sampled using an SKC BioSampler and samples were analyzed using qPCR and plaque assays. The resistance levels of the four phages varied depending on the relative humidity (RH) and germicidal products tested. Phage MS2 was the most stable airborne virus under the environmental conditions tested while phage PR772 was the least stable. Pledge® and Eugenol reduced the infectivity of all airborne phages tested. At 25% RH, Pledge® and Eugenol were more effective at reducing infectivity of RNA phages ϕ6 and MS2. At 50% RH, Pledge® was the most effective agent against phage MS2. These findings illustrate that various airborne viruses should be tested to demonstrate the effectiveness of germicidal treatments. This research also provides a set of parameters for testing germicidal products in large-scale settings to reduce the risk of virus transmission.

Development of adsorptive hybrid filters to enable two-step purification of biologics

Recent progress in mammalian cell culture process has resulted in significantly increased product titers, but also a substantial increase in process- and product-related impurities. Due to the diverse physicochemical properties of these impurities, there is constant need for new technologies that offer higher productivity and improved economics without sacrificing the process robustness required to meet final drug substance specifications. Here, we examined the use of new synthetic adsorptive hybrid filters (AHF) modified with the high binding capacity of quaternary amine (Emphaze™ AEX) and salt-tolerant biomimetic (Emphaze™ ST-AEX) ligands for clearance of process-related impurities like host cell protein (HCP), residual DNA, and virus. The potential to remove soluble aggregates was also examined. Our aim was to develop a mechanistic understanding of the interactions governing adsorptive removal of impurities during filtration by evaluating the effect of various filter types, feed streams, and process conditions on impurity removal. The ionic capacity of these filters was measured and correlated with their ability to remove impurities for multiple molecules. The ionic capacity of AHF significantly exceeded that of traditional adsorptive depth filters (ADF) by 40% for the Emphaze™ AEX and by 700% for the Emphaze™ ST-AEX, providing substantially higher reduction of soluble anionic impurities, including DNA, HCPs and model virus. Nevertheless, we determined that ADF with filter aid provided additional hydrophobic functionality that resulted in removal of higher molecular weight species than AHF. Implementing AHF demonstrated improved process-related impurity removal and viral clearance after Protein A chromatography and enabled a two-step purification process. The consequences of enhanced process performance are far reaching because it allows the downstream polishing train to be restructured and simplified, and chromatographic purity standards to be met with a reduced number of chromatographic steps.

Characterizing Bacteriophage PR772 as a Potential Surrogate for Adenovirus in Water Disinfection: A Comparative Analysis of Inactivation Kinetics and Replication Cycle Inhibition by Free Chlorine

Elucidating mechanisms by which pathogenic waterborne viruses become inactivated by drinking water disinfectants would facilitate the development of sensors to detect infectious viruses and novel disinfection strategies to provide safe water. Using bacteriophages as surrogates for human pathogenic viruses could assist in elucidating these mechanisms; however, an appropriate viral surrogate for human adenovirus (HAdV), a medium-sized virus with a double-stranded DNA genome, needs to be identified. Here, we characterized the inactivation kinetics of bacteriophage PR772, a member of the Tectiviridae family with many similarities in structure and replication to HAdV. The inactivation of PR772 and HAdV by free chlorine had similar kinetics that could be represented with a model previously developed for HAdV type 2 (HAdV-2). We developed and tested a quantitative assay to analyze several steps in the PR772 replication cycle to determine if both viruses being inactivated at similar rates resulted from similar replication cycle events being inhibited. Like HAdV-2, we observed that PR772 inactivated by free chlorine still attached to host cells, and viral DNA synthesis and early and late gene transcription were inhibited. Consequently, free chlorine exposure inhibited a replication cycle event that was post-binding but took place prior to early gene synthesis for both PR772 and HAdV-2.

Resistance of Aerosolized Bacterial Viruses to Relative Humidity and Temperature

The use of aerosolized bacteriophages as surrogates for hazardous viruses might simplify and accelerate the discovery of links between viral components and their persistence in the airborne state under diverse environmental conditions. In this study, four structurally distinct lytic phages, MS2 (single-stranded RNA [ssRNA]), ϕ6 (double-stranded RNA [dsRNA]), ϕX174 (single-stranded DNA [ssDNA]), and PR772 (double-stranded DNA [dsDNA]), were nebulized into a rotating chamber and exposed to various levels of relative humidity (RH) and temperature as well as to germicidal UV radiation. The aerosolized viral particles were allowed to remain airborne for up to 14 h before being sampled for analysis by plaque assays and quantitative PCRs. Phages ϕ6 and MS2 were the most resistant at low levels of relative humidity, while ϕX174 was more resistant at 80% RH. Phage ϕ6 lost its infectivity immediately after exposure to 30°C and 80% RH. The infectivity of all tested phages rapidly declined as a function of the exposure time to UVC radiation, phage MS2 being the most resistant. Taken altogether, our data indicate that these aerosolized phages behave differently under various environmental conditions and highlight the necessity of carefully selecting viral simulants in bioaerosol studies.

Comparison of five bacteriophages as models for viral aerosol studies

Bacteriophages are perceived to be good models for the study of airborne viruses because they are safe to use, some of them display structural features similar to those of human and animal viruses, and they are relatively easy to produce in large quantities. Yet, only a few studies have investigated them as models. It has previously been demonstrated that aerosolization, environmental conditions, and sampling conditions affect viral infectivity, but viral infectivity is virus dependent. Thus, several virus models are likely needed to study their general behavior in aerosols. The aim of this study was to compare the effects of aerosolization and sampling on the infectivity of five tail-less bacteriophages and two pathogenic viruses: MS2 (a single-stranded RNA [ssRNA] phage of the Leviviridae family), Φ6 (a segmented double-stranded RNA [dsRNA] phage of the Cystoviridae family), ΦX174 (a single-stranded DNA [ssDNA] phage of the Microviridae family), PM2 (a double-stranded DNA [dsDNA] phage of the Corticoviridae family), PR772 (a dsDNA phage of the Tectiviridae family), human influenza A virus H1N1 (an ssRNA virus of the Orthomyxoviridae family), and the poultry virus Newcastle disease virus (NDV; an ssRNA virus of the Paramyxoviridae family). Three nebulizers and two nebulization salt buffers (with or without organic fluid) were tested, as were two aerosol sampling devices, a liquid cyclone (SKC BioSampler) and a dry cyclone (National Institute for Occupational Safety and Health two-stage cyclone bioaerosol sampler). The presence of viruses in collected air samples was detected by culture and quantitative PCR (qPCR). Our results showed that these selected five phages behave differently when aerosolized and sampled. RNA phage MS2 and ssDNA phage ΦX174 were the most resistant to aerosolization and sampling. The presence of organic fluid in the nebulization buffer protected phages PR772 and Φ6 throughout the aerosolization and sampling with dry cyclones. In this experimental setup, the behavior of the influenza virus resembled that of phages PR772 and Φ6, while the behavior of NDV was closer to that of phages MS2 and ΦX174. These results provide critical information for the selection of appropriate phage models to mimic the behavior of specific human and animal viruses in aerosols.

Evaluation of concentration efficiency of the Pseudomonas aeruginosa phage PP7 in various water matrixes by different methods

Enteric viruses monitoring in surface waters requires the concentration of viruses before detection assays. The aim of this study was to evaluate different methods in terms of recovery efficiencies of bacteriophage PP7 of Pseudomonas aeruginosa, measured by real-time PCR, using it as a viral control process in water analysis. Different nucleic acid extraction methods (silica-guanidinium thiocyanate, a commercial kit (Qiagen Viral RNA Kit) and phenol-chloroform with alcohol precipitation) exhibited very low recovery efficiencies (0.08-4.18 %), being the most efficient the commercial kit used for subsequent experiments. To evaluate the efficiency of three concentration methods, PBS (as model for clean water) and water samples from rivers were seeded to reach high (HC, 10(6) pfu ml(-1)) and low concentrations (LC, 10(4) pfu ml(-1)) of PP7. Tangential ultrafiltration proved to be more efficient (50.36 ± 12.91, 17.21 ± 9.22 and 12.58 ± 2.35 % for HC in PBS and two river samples, respectively) than adsorption-elution with negatively charged membranes (1.00 ± 1.34, 2.79 ± 2.62 and 0.05 ± 0.08 % for HC in PBS and two river samples, respectively) and polyethylene glycol precipitation (15.95 ± 7.43, 4.01 ± 1.12 and 3.91 ± 0.54 %, for HC in PBS and two river samples, respectively), being 3.2-50.4 times more efficient than the others for PBS and 2.7-252 times for river samples. Efficiencies also depended on the initial virus concentration and aqueous matrixes composition. In consequence, the incorporation of an internal standard like PP7 along the process is useful as a control of the water concentration procedure, the nucleic acid extraction, the presence of inhibitors and the variability of the recovery among replicas, and for the calculation of the sample limit of detection. Thus, the use of a process control, as presented here, is crucial for the accurate quantification of viral contamination.

The attenuation of microorganisms in on-site wastewater effluent discharged into highly permeable subsoils

An extensive field study on percolation areas receiving both septic tank and secondary treated on-site effluents from single houses in Ireland was carried out to investigate the attenuation capacity of highly permeable subsoils with respect to E. coli bacteria and spiked bacteriophages (MS2, ΦX174 and PR772). The development of biomats across the percolation areas receiving the secondary effluent was restricted compared to the percolation area receiving septic tank effluent, promoting a much higher areal hydraulic loading which created significant differences in the potential microbiological loading to groundwater. Greatest E. coli removal in the subsoil occurred within the first 0.35 m of unsaturated subsoil for all effluent types. Analysis showed, however, that more evidence of faecal contamination occurred at depth in the subsoils receiving secondary treated effluents than that receiving septic tank effluent, despite the lower bacterial influent load. All three bacteriophages were reduced to their minimum detection limit (<10 PFU/mL) at a depth of 0.95 m below the percolation trenches receiving septic tank effluent, although isolated incidences of ΦX174 and PR772 were measured below one trench. However again, slightly higher breakthroughs of MS2 and PR772 contamination were detected at the same depth under the trenches receiving secondary treated effluent.

Interactions between rotavirus and Suwannee River organic matter: aggregation, deposition, and adhesion force measurement

Interactions between rotavirus and Suwannee River natural organic matter (NOM) were studied by time-resolved dynamic light scattering, quartz crystal microbalance, and atomic force microscopy. In NOM-containing NaCl solutions of up to 600 mM, rotavirus suspension remained stable for over 4 h. Atomic force microscopy (AFM) measurement for interaction force decay length at different ionic strengths showed that nonelectrostatic repulsive forces were mainly responsible for eliminating aggregation in NaCl solutions. Aggregation rates of rotavirus in solutions containing 20 mg C/L increased with divalent cation concentration until reaching a critical coagulation concentration of 30 mM CaCl(2) or 70 mM MgCl(2). Deposition kinetics of rotavirus on NOM-coated silica surface was studied using quartz crystal microbalance. Experimental attachment efficiencies for rotavirus adsorption to NOM-coated surface in MgCl(2) solution were lower than in CaCl(2) solution at a given divalent cation concentration. Stronger adhesion force was measured for virus-virus and virus-NOM interactions in CaCl(2) solution compared to those in MgCl(2) or NaCl solutions at the same ionic strength. This study suggested that divalent cation complexation with carboxylate groups in NOM and on virus surface was an important mechanism in the deposition and aggregation kinetics of rotavirus.

Impact of riparian zone protection from cattle on nutrient, bacteria, F-coliphage, and loading of an intermittent stream

This 5-yr study compared, via an upstream-downstream experimental design, nutrient and microbial water quality of an intermittent stream running through a small pasture (∼2.5 animals ha) where cattle are restricted from the riparian zone (restricted cattle access [RCA]) and where cattle have unrestricted access to the stream (unrestricted cattle access [URCA]). Fencing in the RCA excluded pasturing cattle to within ∼3 to 5 m of the stream. Approximately 88% (26/32) of all comparisons of mean contaminant load reduction for lower, higher, and all stream flow conditions during the 5-yr study indicated net contaminant load reductions in the RCA; for the URCA, this percentage was 38% (12/32). For all flow conditions, mean percent load reductions in the RCA for nutrients and bacteria plus F-coliphage were 24 and 23%, respectively. These respective percentages for the URCA were -9 and -57% (positive values are reductions; negative values are increases). However, potentially as a result of protected wildlife habitat in the RCA, the mean percent load reduction for for "all flow" was -321% for the RCA and 60% for the URCA; for , these respective percentages were -209% (RCA) and 73% (URCA). For "all flow" situations, mean load reductions for the RCA were significantly greater ( < 0.1) than those from the URCA for NH-N, dissolved reactive phosphorus (DRP), total coliform, , and . For "high flow" situations, mean load reductions were significantly greater for the RCA for DRP, total coliform, and . For "low flow" conditions, significantly greater mean load reductions were in favor of the RCA for DRP, total P, total coliforms, fecal coliforms, , and . In no case were mean pollutant loads in the URCA significantly higher than RCA pollutant loads. Restricting pasturing livestock to within 3 to 5 m of intermittent streams can improve water quality; however, water quality impairment can occur if livestock have unrestricted access to a stream.

Evaluation of electrospray differential mobility analysis for virus particle analysis: Potential applications for biomanufacturing

The technique of electrospray differential mobility analysis (ES-DMA) was examined as a potential potency assay for routine virus particle analysis in biomanufacturing environments (e.g., evaluation of vaccines and gene delivery products for lot release) in the context of the International Committee of Harmonisation (ICH) Q2 guidelines. ES-DMA is a rapid particle sizing method capable of characterizing certain aspects of the structure (such as capsid proteins) and obtaining complete size distributions of viruses and virus-like particles. It was shown that ES-DMA can distinguish intact virus particles from degraded particles and measure the concentration of virus particles when calibrated with nanoparticles of known concentration. The technique has a measurement uncertainty of ≈20%, is linear over nearly 3 orders of magnitude, and has a lower limit of detection of ≈10⁹ particles/mL. This quantitative assay was demonstrated for non-enveloped viruses. It is expected that ES-DMA will be a useful method for applications involving production and quality control of vaccines and gene therapy vectors for human use.

Deposition and aggregation kinetics of rotavirus in divalent cation solutions

Aggregation kinetics of rotavirus in aqueous solutions and its deposition kinetics on silica surface in the presence of divalent (Ca(2+), Mg(2+)) cations were studied using complementary techniques of time-resolved dynamic light scattering (TR-DLS) and quartz crystal microbalance (QCM). Within a reasonable temporal window of 4 h, aggregation could be observed at levels as low as 10 mM of Ca(2+) and 20 mM of Mg(2+). Attachment efficiencies were always greater in Ca(2+) solutions of the same concentration, and the critical coagulation concentration (CCC) for rotavirus in Ca(2+) solutions was slightly smaller than that in Mg(2+) solutions. No aggregation was detected in Na(+) solution within the temporal window of 4 h. Deposition experiments showed higher attachment coefficients in solutions containing Ca(2+) compared to those obtained in Mg(2+) solution. The classic Derjaguin-Landau-Verwey-Overbeek (DLVO) theory failed to predict both the aggregation behavior of rotavirus and its deposition on silica surface. Besides electrostatic interactions, steric repulsions and specific interactions with divalent cations were important mechanisms in controlling rotavirus deposition and aggregation. Experimental results presented here suggest that rotavirus is not expected to aggregate in groundwater with typical hardness (up to 6 mM Ca(2+)) and rotavirus deposition on silica soil would be more favorable in the presence of Ca(2+) than Mg(2+).

Optimal preparation and purification of PRD1-like bacteriophages for use in environmental fate and transport studies

Bacteriophages are bacterial viruses with unique characteristics that make them excellent surrogates for mammalian pathogenic viruses in environmental studies. Simple and reliable methodologies for isolation, detection, characterization and enumeration of somatic and F-specific bacteriophage are available in the literature. Limited information or methods are available for producing high-titer purified phage suspensions for studying microbial transport and survival in natural and engineered environments. This deficiency arises because most research on the production of high-titer phage suspensions was completed over half a century ago and more recent advances on these methods have not been compiled in a single publication. We present a review of the available methods and new data on the propagation, concentration and purification of two bacteriophage host systems (somatic PRD1/Salmonella thyphimurium and F-specific PR772/Escherichia coli) that are commonly utilized in laboratory and field-scale assessments of subsurface microbial transport and survival. The focus of the present study is to recommend the approach(es) that will ensure maximum bacteriophage yields while optimizing suspension purification (i.e. avoiding modification of surface charge of the phage capsids and/or inadvertent introduction of dissolved organic matter to the study system).

Basic oxygen furnace slag as a treatment material for pathogens: contribution of inactivation and attachment in virus attenuation

Basic oxygen furnace (BOF) slag media were studied as a potential treatment material in on-site sanitation systems. Batch and column studies were conducted to evaluate attenuation of the bacteriophage PR772 and 0.190 microm diameter microspheres by BOF media, and to delineate the relative contributions of two principle processes of virus attenuation: inactivation and attachment. In the batch studies, conducted at 4 degrees C, substantial inactivation of PR772 did not occur in the pH 7.6 and 9.5 suspensions. At pH 11.4, bimodal inactivation of PR772 was observed, at an initial rate of 2.1 log C/C(0) day(-1) for the first two days, followed by a much slower rate of 0.124 log C/C(0) day(-1) over the following 10 days. Two column studies were conducted at 4 degrees C at a flow rate of 1 pore volume day(-1) using two slag sources (Stelco, Ontario; Tubarão, Brazil) combined with sand and pea gravel. In both column experiments, the effluent microsphere concentration approached input concentrations over time (reductions of 0.1-0.2 log C/C(0)), suggesting attachment processes for microspheres were negligible. Removal of PR772 virus was more pronounced both during the early stages of the experiments, but also after longer transport times (0.5-1.0 log C/C(0)). PR772 reduction appeared to be primarily as a result of virus inactivation in response to the elevated pH conditions generated by the BOF mixture (10.6-11.4). On-site sanitation systems using BOF media should be designed to maintain sufficient contact time between the BOF media and the wastewater to allow sufficient residence time of pathogens at elevated pH conditions.

Quantitative characterization of virus-like particles by asymmetrical flow field flow fractionation, electrospray differential mobility analysis, and transmission electron microscopy

Here we characterize virus-like particles (VLPs) by three very distinct, orthogonal, and quantitative techniques: electrospray differential mobility analysis (ES-DMA), asymmetric flow field-flow fractionation with multi-angle light scattering detection (AFFFF-MALS) and transmission electron microscopy (TEM). VLPs are biomolecular particles assembled from viral proteins with applications ranging from synthetic vaccines to vectors for delivery of gene and drug therapies. VLPs may have polydispersed, multimodal size distributions, where the size distribution can be altered by subtle changes in the production process. These three techniques detect subtle size differences in VLPs derived from the non-enveloped murine polyomavirus (MPV) following: (i) functionalization of the surface of VLPs with an influenza viral peptide fragment; (ii) packaging of foreign protein internally within the VLPs; and (iii) packaging of genomic DNA internally within the VLPs. These results demonstrate that ES-DMA and AFFFF-MALS are able to quantitatively determine VLP size distributions with greater rapidity and statistical significance than TEM, providing useful technologies for product development and process analytics.

Effects of temperature and shear force on infectivity of the baculovirus Autographa californica M nucleopolyhedrovirus

Virus stability and infectivity during stressful conditions was assessed to establish guidelines for future virus filtration experiments and to contribute to the body of knowledge on a widely used virus. A recombinant baculovirus of Autographa californica M nucleopolyhedrovirus (AcMNPV), vHSGFP, was incubated at 15-65 degrees C. A 2-log decrease in virus infectivity occurred after virus incubation above 45 degrees C. The activation energy of virus deactivation was circa 108 kJ/mol. Dynamic light scattering revealed an increase in apparent virus particle size from 150+/-19 to 249+/-13 nm at 55 degrees C. Protein and DNA concentrations in solution correlated well with virus aggregation as temperature was increased. Infectivity of vHSGFP stored for 5 months at 4 degrees C or exposed to shear stress from stirring (100 rpm, 1.02x10(-5) psi) and pumping (50-250 ml/min, 1.45x10(-5) to 7.25x10(-5) psi) did not change with time. Unlike temperature variations, cold storage and shear stress appeared to have little impact on infectivity.

Characterization and purification of bacteriophages using chromatofocusing

The technique of chromatofocusing was applied to the characterization and purification of three bacteriophages that are routinely used for testing virus filters: phiX174, PR772, and PP7. Chemically well-defined eluent buffers were used, instead of the more commonly used chromatofocusing polyampholyte buffers. Chromatographic column packings were selected to minimize band broadening by confining bacteriophage adsorption solely to the exterior particle surface. Under the conditions used it was determined that bacteriophages could be made to focus into narrow bands in a retained pH gradient with recoveries of live phage that ranged from 15 to nearly 100% as determined by a plaque-forming assay. Retention times and apparent isoelectric point data were obtained for samples consisting either of purified bacteriophage, or samples consisting of crude preparations of bacteriophages containing host cell impurities. Isoelectric point estimates were obtained using modified, previously described models. The results obtained suggest that chromatofocusing is a simple and rapid method for obtaining approximate isoelectric points for bacteriophages and probably other types of viruses. It is also likely a useful method for purifying these materials.

Curated list of prokaryote viruses with fully sequenced genomes

Genome sequencing is of enormous importance for classification of prokaryote viruses and for understanding the evolution of these viruses. This survey covers 284 sequenced viruses for which a full description has been published and for which the morphology is known. This corresponds to 219 (4%) of tailed and 75 (36%) of tailless viruses of prokaryotes. The number of sequenced tailless viruses almost doubles if viruses of unknown morphology are counted. The sequences are from representatives of 15 virus families and three groups without family status, including eight taxa of archaeal viruses. Tailed phages, especially those with large genomes and hosts other than enterobacteria or lactococci, mycobacteria and pseudomonads, are vastly under investigated.

A snapshot of viral evolution from genome analysis of the tectiviridae family

The origin, evolution and relationships of viruses are all fascinating topics. Current thinking in these areas is strongly influenced by the tailed double-stranded (ds) DNA bacteriophages. These viruses have mosaic genomes produced by genetic exchange and so new natural isolates are quite dissimilar to each other, and to laboratory strains. Consequently, they are not amenable to study by current tools for phylogenetic analysis. Less attention has been paid to the Tectiviridae family, which embraces icosahedral dsDNA bacterial viruses with an internal lipid membrane. It includes viruses, such as PRD1, that infect Gram-negative bacteria, as well as viruses like Bam35 with Gram-positive hosts. Although PRD1 and Bam35 have closely related virion morphology and genome organization, they have no detectable sequence similarity. There is strong evidence that the Bam35 coat protein has the "double-barrel trimer" arrangement of PRD1 that was first observed in adenovirus and is predicted to occur in other viruses with large facets. It is very likely that a single ancestral virus gave rise to this very large group of viruses. The unprecedented degree of conservation recently observed for two Bam35-like tectiviruses made it important to investigate those infecting Gram-negative bacteria. The DNA sequences for six PRD1-like isolates (PRD1, PR3, PR4, PR5, L17, PR772) have now been determined. Remarkably, these bacteriophages, isolated at distinctly different dates and global locations, have almost identical genomes. The discovery of almost invariant genomes for the two main Tectiviridae groups contrasts sharply with the situation in the tailed dsDNA bacteriophages. Notably, it permits a sequence analysis of the isolates revealing that the tectiviral proteins can be dissected into a slowly evolving group descended from the ancestor, the viral self, and a more rapidly changing group reflecting interactions with the host.