Comparing Various Resin Luting Cement Systems in Different Etching Modes Through Bond Durability and Morphological Features

OBJECTIVES

This study aimed to investigate bond performance of various resin luting cement (RLC) systems on enamel and dentin in different etching modes and to compare the RLC-tooth interface morphology using scanning electron microscopy (SEM).

METHODS AND MATERIALS

The self-adhesive RLC systems used in combination with universal adhesives were as follows: Scotchbond Universal Adhesive Plus + RelyX Universal (3M Oral Care) and Clearfil Universal Bond Quick ER + SA Luting Multi (Kuraray Noritake Dental). These RLC systems were also used alone as self-adhesive RLC systems without universal adhesives (self-adhesive mode). The conventional RLC systems for comparison materials were as follows: BeautiBond Xtream + ResiCem EX (Shofu) and Tooth Primer + Panavia V5 (Kuraray Noritake Dental). Twelve specimens were prepared for each group to measure shear bond strength (SBS) in different etching modes. A stainless-steel rod was used as a substitute for indirect restorations. Bonded specimens were allocated to baseline (stored for 24 hours) and artificially aged (thermocycling [TC] for 10,000 cycles) groups. Representative treated tooth surfaces and RLC-tooth interfaces were observed using SEM.

RESULTS

Three-way analysis of variance (ANOVA) revealed that all the factors (etching mode, storage period, and RLC system) had a significant influence on the enamel SBS values (p<0.05). Enamel SBS was significantly higher in etch-&-rinse (ER) mode than in self-etch (SE) mode, regardless of RLC system or storage period. Three-way ANOVA showed that all the factors had a significant influence on the dentin SBS values (p<0.001). Most RLC systems showed significantly higher dentin SBS in SE mode than in ER mode, regardless of storage period. However, the combination with Scotchbond Universal Adhesive Plus and RelyX Universal showed no significant difference in SBS values between etching modes at the baseline and showed a significantly higher SBS value in ER mode than in SE mode after TC.

CONCLUSIONS

The self-adhesive RLC systems with universal adhesives tended to show higher enamel and dentin bond performance than the self-adhesive RLC systems alone. The morphology of treated tooth surfaces and resin cement-tooth interfaces were dependent on the RLC system and etching mode used. The RLC systems with primer application showed a thin, high-density layer above the intact dentin in both etching modes, suggesting chemical interaction.

Controlling Physical and Biochemical Parameters of Actin Nucleation Using a Patterned Model Lipid Membrane

Self-assembly of nanoscale actin cytoskeletal proteins into filamentous networks requires organizing actin nucleation areas on the plasma membrane through recruiting actin nucleators and nucleation-promoting factors (NPFs) to the areas. To investigate impacts of the nucleation geometry on actin network assembly, we localized NPF or nucleator on defined micropatterns of laterally mobile lipid bilayers confined in a framework of a polymerized lipid bilayer. We demonstrated that actin network assembly in purified protein mixtures was confined on NPF- or nucleator-localized fluid bilayers. By controlling the shape and size of nucleation areas as well as the density and types of localized NPFs and nucleators, we showed that these parameters regulate actin network architectures. Actin network assembly in Xenopus egg extracts was also spatially controlled by patterning bilayers containing phosphatidylinositol 4,5-bisphoshate (PI(4,5)P2), an essential lipid signaling mediator. Therefore, the system provides a promising platform to investigate the physical and biochemical principles for actin network assembly.

Effects of empagliflozin on progression of chronic kidney disease: a prespecified secondary analysis from the empa-kidney trial

BACKGROUND

Sodium-glucose co-transporter-2 (SGLT2) inhibitors reduce progression of chronic kidney disease and the risk of cardiovascular morbidity and mortality in a wide range of patients. However, their effects on kidney disease progression in some patients with chronic kidney disease are unclear because few clinical kidney outcomes occurred among such patients in the completed trials. In particular, some guidelines stratify their level of recommendation about who should be treated with SGLT2 inhibitors based on diabetes status and albuminuria. We aimed to assess the effects of empagliflozin on progression of chronic kidney disease both overall and among specific types of participants in the EMPA-KIDNEY trial.

METHODS

EMPA-KIDNEY, a randomised, controlled, phase 3 trial, was conducted at 241 centres in eight countries (Canada, China, Germany, Italy, Japan, Malaysia, the UK, and the USA), and included individuals aged 18 years or older with an estimated glomerular filtration rate (eGFR) of 20 to less than 45 mL/min per 1·73 m2, or with an eGFR of 45 to less than 90 mL/min per 1·73 m2 with a urinary albumin-to-creatinine ratio (uACR) of 200 mg/g or higher. We explored the effects of 10 mg oral empagliflozin once daily versus placebo on the annualised rate of change in estimated glomerular filtration rate (eGFR slope), a tertiary outcome. We studied the acute slope (from randomisation to 2 months) and chronic slope (from 2 months onwards) separately, using shared parameter models to estimate the latter. Analyses were done in all randomly assigned participants by intention to treat. EMPA-KIDNEY is registered at ClinicalTrials.gov, NCT03594110.

FINDINGS

Between May 15, 2019, and April 16, 2021, 6609 participants were randomly assigned and then followed up for a median of 2·0 years (IQR 1·5-2·4). Prespecified subgroups of eGFR included 2282 (34·5%) participants with an eGFR of less than 30 mL/min per 1·73 m2, 2928 (44·3%) with an eGFR of 30 to less than 45 mL/min per 1·73 m2, and 1399 (21·2%) with an eGFR 45 mL/min per 1·73 m2 or higher. Prespecified subgroups of uACR included 1328 (20·1%) with a uACR of less than 30 mg/g, 1864 (28·2%) with a uACR of 30 to 300 mg/g, and 3417 (51·7%) with a uACR of more than 300 mg/g. Overall, allocation to empagliflozin caused an acute 2·12 mL/min per 1·73 m2 (95% CI 1·83-2·41) reduction in eGFR, equivalent to a 6% (5-6) dip in the first 2 months. After this, it halved the chronic slope from -2·75 to -1·37 mL/min per 1·73 m2 per year (relative difference 50%, 95% CI 42-58). The absolute and relative benefits of empagliflozin on the magnitude of the chronic slope varied significantly depending on diabetes status and baseline levels of eGFR and uACR. In particular, the absolute difference in chronic slopes was lower in patients with lower baseline uACR, but because this group progressed more slowly than those with higher uACR, this translated to a larger relative difference in chronic slopes in this group (86% [36-136] reduction in the chronic slope among those with baseline uACR <30 mg/g compared with a 29% [19-38] reduction for those with baseline uACR ≥2000 mg/g; ptrend<0·0001).

INTERPRETATION

Empagliflozin slowed the rate of progression of chronic kidney disease among all types of participant in the EMPA-KIDNEY trial, including those with little albuminuria. Albuminuria alone should not be used to determine whether to treat with an SGLT2 inhibitor.

FUNDING

Boehringer Ingelheim and Eli Lilly.

Impact of primary kidney disease on the effects of empagliflozin in patients with chronic kidney disease: secondary analyses of the EMPA-KIDNEY trial

BACKGROUND

The EMPA-KIDNEY trial showed that empagliflozin reduced the risk of the primary composite outcome of kidney disease progression or cardiovascular death in patients with chronic kidney disease mainly through slowing progression. We aimed to assess how effects of empagliflozin might differ by primary kidney disease across its broad population.

METHODS

EMPA-KIDNEY, a randomised, controlled, phase 3 trial, was conducted at 241 centres in eight countries (Canada, China, Germany, Italy, Japan, Malaysia, the UK, and the USA). Patients were eligible if their estimated glomerular filtration rate (eGFR) was 20 to less than 45 mL/min per 1·73 m2, or 45 to less than 90 mL/min per 1·73 m2 with a urinary albumin-to-creatinine ratio (uACR) of 200 mg/g or higher at screening. They were randomly assigned (1:1) to 10 mg oral empagliflozin once daily or matching placebo. Effects on kidney disease progression (defined as a sustained ≥40% eGFR decline from randomisation, end-stage kidney disease, a sustained eGFR below 10 mL/min per 1·73 m2, or death from kidney failure) were assessed using prespecified Cox models, and eGFR slope analyses used shared parameter models. Subgroup comparisons were performed by including relevant interaction terms in models. EMPA-KIDNEY is registered with ClinicalTrials.gov, NCT03594110.

FINDINGS

Between May 15, 2019, and April 16, 2021, 6609 participants were randomly assigned and followed up for a median of 2·0 years (IQR 1·5-2·4). Prespecified subgroupings by primary kidney disease included 2057 (31·1%) participants with diabetic kidney disease, 1669 (25·3%) with glomerular disease, 1445 (21·9%) with hypertensive or renovascular disease, and 1438 (21·8%) with other or unknown causes. Kidney disease progression occurred in 384 (11·6%) of 3304 patients in the empagliflozin group and 504 (15·2%) of 3305 patients in the placebo group (hazard ratio 0·71 [95% CI 0·62-0·81]), with no evidence that the relative effect size varied significantly by primary kidney disease (pheterogeneity=0·62). The between-group difference in chronic eGFR slopes (ie, from 2 months to final follow-up) was 1·37 mL/min per 1·73 m2 per year (95% CI 1·16-1·59), representing a 50% (42-58) reduction in the rate of chronic eGFR decline. This relative effect of empagliflozin on chronic eGFR slope was similar in analyses by different primary kidney diseases, including in explorations by type of glomerular disease and diabetes (p values for heterogeneity all >0·1).

INTERPRETATION

In a broad range of patients with chronic kidney disease at risk of progression, including a wide range of non-diabetic causes of chronic kidney disease, empagliflozin reduced risk of kidney disease progression. Relative effect sizes were broadly similar irrespective of the cause of primary kidney disease, suggesting that SGLT2 inhibitors should be part of a standard of care to minimise risk of kidney failure in chronic kidney disease.

FUNDING

Boehringer Ingelheim, Eli Lilly, and UK Medical Research Council.

Dosimetric Comparison of Automated Non-Coplanar Volumetric-Modulated Arc Therapy and Intensity-Modulated Proton Therapy in Angiosarcoma of the Scalp

PURPOSE/OBJECTIVE(S)

Angiosarcoma of the scalp (AS) is a rare tumor and has often been treated by total scalp irradiation (TSI). TSI is a challenging technique because of the target close to the organs at risks (OARs), located in the skin surface, and helmet-shape of the target. We performed the dosimetric comparison of automated non-coplanar volumetric-modulated arc therapy (HA) and intensity-modulated proton therapy (IMPT) in TSI for AS.

MATERIALS/METHODS

A planning study was performed on 20 patients with AS. The clinical target volume (CTV) 1 and CTV2 were defined as gross tumor volume with margin and entire scalp, respectively. For HA, planning target volume (PTV) 1 and PTV2 were defined as CTV1 and CTV2 with 5-mm margins, respectively. For IMPT, robust optimization was utilized which accounted for a 5-mm setup and a 3.5% range uncertainty and dose was prescribed to CTV1 robust and CTV2 robust. The prescription doses were 70 Gy and 56 Gy in 35 fractions to PTV1 (CTV1 robust) and PTV2 (CTV2 robust), respectively, using the simultaneous integrated boost technique. The HA plan was performed using a 6-MV photon beam machine and a 1-cm thick virtual bolus. The HA plan included three half non-coplanar and one full coplanar arc fields. The HA plan used collimator angles of 15°, 60°, 15°, and 120° in the beam with couch rotations of 0°, 45°, 90°, and 315°, respectively. The IMPT plan was performed using a compact proton beam machine dedicated to pencil beam scanning. The IMPT plan used gantry angles of 70°, 150°, 70°, 150°, and 30° in the beam with couch rotations of 0°, 0°, 180°, 180°, and 270°, respectively. The IMPT plan was optimized assuming a relative biological effectiveness of 1.1. The dose distribution and dosimetric parameters for each plan were evaluated.

RESULTS

All plans met the goals within the acceptable range in target volume coverage, conformity, and homogeneity. Table shows the dosimetric parameters of OARs in HA and IMPT plans. The doses receiving 0.1 cc of the volume for hippocampus, optic passway, eye, and lens in the IMPT plan were significantly lower than those in the HA plan. The IMPT plan showed a significant reduction in the percentage of brain volume receiving at least 5 Gy (V5 Gy) compared to the HA plan, while the HA plan showed a significant reduction of V10 Gy - V60 Gy and mean brain dose compared to the IMPT plan. The HA plan provided a shorter beam-on time (184 ± 9 s) than did the IMPT plan (446 ± 49 s).

CONCLUSION

The HA and IMPT plans demonstrated different strengths with respect to OARs sparing.

Prevalence trends of metabolic syndrome in residents of postdisaster Fukushima: a longitudinal analysis of Fukushima Health Database 2012-2019

OBJECTIVES

The study aimed to evaluate the long-term metabolic risk profiles of Fukushima residents after the Great East Japan Earthquake of March 2011.

STUDY DESIGN

This was a cross-sectional and a longitudinal design.

METHODS

The Fukushima Health Database (FDB) contains 2,331,319 annual health checkup records of participants aged 40-74 years between 2012 and 2019. We checked the validity of the FDB by comparing the prevalence of metabolic factors with the National Database of Health Insurance Claims and Specific Health Checkups (NDB). We applied a regression analysis to determine the changes and project the trends of metabolic factors over the years.

RESULTS

Compared to the NDB, the prevalence of metabolic factors in Fukushima was higher than the country average from 2013 to 2018, and they showed the same trends as those from the FDB. The prevalence of metabolic syndrome (MetS) increased from 18.9% in 2012 to 21.4% in 2019 (an annual increase of 2.74%) in men and from 6.8 to 7.4% (an annual increase of 1.80%) in women in Fukushima. The standardized prevalence of MetS, being overweight, and diabetes is projected to continue increasing, with disparities among subareas being higher in evacuees than in non-evacuees. An annual decrease of 0.38-1.97% in hypertension was mainly observed in women.

CONCLUSIONS

The prevalence of metabolic risk is higher in Fukushima as compared to the country average. The increasing metabolic risk in subareas, including the evacuation zone, highlights the need to control MetS in Fukushima residents.

Microscopic Temperature Control Reveals Cooperative Regulation of Actin-Myosin Interaction by Drebrin E

Drebrin E is a regulatory protein of intracellular force produced by actomyosin complexes, that is, myosin molecular motors interacting with actin filaments. The expression level of drebrin E in nerve cells decreases as the animal grows, suggesting its pivotal but unclarified role in neuronal development. Here, by applying the microscopic heat pulse method to actomyosin motility assay, the regulatory mechanism is examined from the room temperature up to 37 °C without a thermal denaturing of proteins. We show that the inhibition of actomyosin motility by drebrin E is eliminated immediately and reversibly during heating and depends on drebrin E concentration. The direct observation of quantum dot-labeled drebrin E implies its stable binding to actin filaments during the heat-induced sliding. Our results suggest that drebrin E allosterically modifies the actin filament structure to regulate cooperatively the actomyosin activity at the maintained in vivo body temperature.

Left atrial dysfunction still exists in patients who obtain normal left atrial volume after successful ablation of atrial fibrillation

Introduction

Atrial fibrillation (AF) promotes left atrial (LA) remodeling and vice versa. LA volume index (LAVI) ≥34 mL/m2 is an established cut-off value for identifying an enlarged left atrium. Catheter ablation has become an established therapy for AF and provides a reduction of LA volume by maintaining sinus rhythm (reverse remodeling). However, the definition of LA reverse remodeling after AF ablation is undetermined.

Purpose

We hypothesized that patients with LA dilatation who obtain normal LA volume (LAVI &lt;34 mL/m2) after AF ablation would have better long-term outcomes than those who do not. Furthermore, we investigated whether patients with a normal LA volume could also obtain normal LA function with AF ablation.

Methods

We enrolled 140 AF patients with baseline LAVI ≥34 mL/m2, without AF recurrence for 1 year after the initial AF ablation. We acquired conventional and speckle-tracking echocardiographic parameters within 24 h and at 1 year after the procedure. Late recurrence was defined as AF recurrence &gt;1 year after the initial ablation. To define the normal range of LA function, age-and sex-matched 140 controls without a history of AF were also enrolled.

Results

After restoration of sinus rhythm, overall LA structural and functional parameters were significantly improved, and 75 patients (54%) had normal LA volume at the time of follow-up (Table). During a median follow-up of 44 (31–61) months, 32 patients (23%) experienced a late recurrence of AF. Patients who obtained normal LA volume after AF ablation had fewer late recurrences than those who did not (P&lt;0.01) (Figure). However, LA functional abnormalities still existed in AF patients, even if LA volume was normalized as in controls (Table).

Conclusion

Patients who obtain normal LA volume have better long-term outcomes of AF ablation than those who do not. Although AF ablation promotes beneficial effects on LA structure and function, LA function cannot be normalized even in patients who obtain normal LA volume after successful ablation. Thus, physicians should carefully consider long-term follow-up and residual AF risks, regardless of sinus rhythm restoration by catheter ablation.

Funding Acknowledgement

Type of funding sources: None.

Handling and Mechanical Properties of Low-viscosity Bulk-fill Resin Composites

This study aimed to evaluate the filler contents (FCs), flexural properties, depth of cure (DOC), wear resistance, and handling properties of different low-viscosity bulk-fill resin composites (LVBRCs) and to determine the correlations between the tested parameters. Six LVBRCs, Beautifil-Bulk (BBF), Bulk Base Hard (BBH), Bulk Base Medium (BBM), Filtek Bulk-Fill Flowable Restorative (FBF), G-ænial Bulk Injectable (GBI), and SDR flow+ Bulk-Fill Flowable (SDR) were used. The DOC and flexural property tests were conducted according to the ISO 4049 specifications. The flexural strength, elastic modulus, and resilience were determined in 12 specimens that were obtained from each of the 6 materials. Sliding-impact-wear testing was conducted by evaluating the wear facets of the specimens using a noncontact profilometer and by confocal laser scanning microscopy. The handling properties of the LVBRC was assessed via extrusion force and thread formation measurements. The DOC for the majority of the LVBRCs was approximately 4 mm. Although the FCs and mechanical properties were material dependent, some LVBRCs exhibited excellent flexural properties and wear resistance. The LVBRCs demonstrated a wide range of extrusion force and thread formation. Regarding the correlations between the tested parameters, extremely strong negative and positive correlations were observed for the DOC versus extrusion force, flexural strength versus elastic modulus, maximum depth versus volume loss, and maximum depth versus thread formation. In addition, strong correlations between FCs and DOC, resilience, wear resistance, and extrusion force were observed.

Flexural Properties and Polished Surface Characteristics of a Structural Colored Resin Composite

OBJECTIVE

The aim of this study was to determine the flexural properties and surface characteristics of a structural colored resin composite after different finishing and polishing methods, in comparison to those of conventional resin composites.

METHODS AND MATERIALS

A structural color resin composite, Omnichroma (OM, Tokuyama Corp, Chiyoda City, Tokyo, Japan), and two comparison resin composites, Filtek Supreme Ultra (FS, 3M, St Paul, MN, USA) and Tetric EvoCeram (TE, Ivoclar Vivadent, Schaan, Liechtenstein), were used. The flexural properties of the resin composites were determined in accordance with the ISO 4049 specifications. For surface properties, 70 polymerized specimens of each resin composite were prepared and divided into seven groups of 10. Surface roughness (Sa), gloss (GU), and surface free energy (SFE) were investigated after the following finishing and polishing methods. Three groups of specimens were finished with a superfine-grit diamond bur (SFD), and three with a tungsten carbide bur (TCB). After finishing, one of the two remaining groups was polished with a one-step silicone point (CMP), and the other with an aluminum oxide flexible disk (SSD). A group ground with SiC 320-grit was set as a baseline.

RESULTS

The average flexural strength ranged from 116.6 to 142.3 MPa in the following order with significant differences between each value: FS > TE > OM. The average E ranged from 6.8 to 13.2 GPa in the following order with significant differences between each value: FS > TE > OM. The average R ranged from 0.77 to 1.01 MJ/mm3 in the following order: OM > FS > TE. The Sa values of the OM groups polished with CMP and SSD were found to be significantly lower than those of the other resin composites, regardless of the finishing method. The GU values appeared to be dependent on the material and the finishing method used. The OM specimens polished with SSD showed significantly higher GU values than those polished with CMP. Most of the resin composites polished with SSD demonstrated significantly higher γS values compared to the other groups. Extremely strong negative correlations between Sa and GU in the combined data from the three resin composites and each resin composite and between Sa and γS in the OM specimens were observed; GU showed a strong positive correlation with γS in the same material.

CONCLUSION

These findings indicate that both flexural and surface properties are material dependent. Furthermore, the different finishing and polishing methods used in this study were observed to affect the Sa, GU, and SFE of the resin composites.

Evaluation of Color-matching Ability of a Structural Colored Resin Composite

PURPOSE

The present study evaluated the color-matching ability of a structural colored resin composite to compare it with resin composites employing pigments.

METHODS AND MATERIALS

A structural colored resin composite (Omnichroma [OMC]), a supranano-filled resin composite (Estelite ∑ Quick [ELQ]), and a nano-filled resin composite (Filtek Supreme Ultra [FSU]) were used. Each resin composite was packed into a Teflon mold and pressed down with a clear strip under a glass slide. The specimens were light irradiated through the slide with a light-emitting diode curing unit. The thickness of the specimens (n=6) was measured with a digital caliper before being transferred to distilled water and stored at 37°C for 24 hours. The measurements of the optical characteristics of the specimens on a black-and-white background were performed using a spectrophotometer. D65 (CIE D65) was used as a light source for the spectrophotometer. Measurements were repeated three times for each specimen under each color-measurement condition, and average values for three same-shade specimens were calculated. One-way analysis of variance and Tukey post hoc tests were used (α=0.05). To determine its ability to match the color of artificial teeth, each shade of resin composite was placed in a cavity before performing color measurements. Using a spectrophotometer (CMS-35F S/C) with a flexible sensor, L*, a*, and b* values were obtained.

RESULTS

The spectral reflectance curve of OMC showed that it reflected light wavelengths from 430-700 nm regardless of the background color and thickness of the specimens. The percentage of reflectance of ELQ decreased near wavelengths of 550-580 nm. Regarding the influence of background color on CIE L*, a*, b* values, the L* level showed significantly higher values for all tested materials with white backgrounds, and OMC was most affected by the difference in background color. However, a* values of ELQ and FSU were significantly higher with a black background than with a white background, and OMC showed a significantly higher value with a white background than with a black background. The b* values were higher with a white background than with a black background and were significantly higher for all three products, and these tendencies were much greater for ELQ and FSU.

CONCLUSIONS

The ability of OMC to match the color of artificial teeth showed acceptable color compatibility, regardless of the shade of the artificial teeth and the depth of the cavity. However, ELQ and FSU showed reduced color compatibility, especially for a cavity depth of 3.0 mm. Excellent color matching ability was confirmed for the structural colored resin composite OMC, resulting in reduced color differences and therefore improving the esthetic appearance of the restoration, simplifying shade matching, and compensating for any color mismatch.

Effect of Layering Techniques on Polymerization Shrinkage Stress of High- and Low-viscosity Bulk-fill Resins

CLINICAL RELEVANCE

The use of layering techniques is still advisable with many bulk-fill resins and should be the default unless a particular resin is known to not need it.

SUMMARY

Objective: The purpose of this study was to investigate how layering techniques affect polymerization shrinkage stresses of high-and low-viscosity bulk-fill resins.Method: Six high-viscosity and six low-viscosity bulk-fill resins were evaluated. Aluminum blocks with a mesial-occlusal-distal (MOD) cavity were machined and randomly divided into groups for different filling techniques (bulk-fill vs horizontal layering vs oblique layering) and further subdivided according to type of resin (high- vs low-viscosity). The cuspal deflection resulting from the polymerization of bulk-fill resin bonded to a MOD cavity within an aluminum block was measured with a digimatic micrometer. Scanning electron microscopy analyses of tested resins were also conducted.Results: In the high-viscosity bulk-fill resins, cuspal deflection of the MOD cavity ranged from 11.2 to 18.2 μm with the bulk-filling technique, from 10.7 to 15.5 μm with the horizontal layering technique, and from 10.9 to 15.2 μm with the oblique layering technique. In the low-viscosity bulk-fill resins, cuspal deflection of the material ranged from 9.2 to 19.8 μm with the bulk-filling technique, from 8.2 to 15.7 μm with the horizontal layering technique, and from 8.4 to 16.4 μm with the oblique layering technique.Conclusion: Cuspal deflections for some high-and low-viscosity bulk-fill resins were significantly reduced by using layering techniques, but the resultant improvement of layering techniques was not applicable to all the bulk-fill resins used in this study.

Simulated Cuspal Deflection and Flexural Properties of Bulk-Fill and Conventional Flowable Resin Composites

CLINICAL RELEVANCE

Some bulk-fill flowable resin composites produce less cuspal deflection than a conventional incrementally filled flowable resin composites.

SUMMARY

Objective: This study investigated simulated cuspal deflection and flexural properties of bulk-fill and conventional flowable resin composites.Methods and Materials: Five bulk-fill and six conventional flowable resin composites were evaluated. Aluminium blocks with a mesio-occlusal-distal cavity were prepared and randomly divided into groups for each of the different measurement techniques and were further subdivided according to the type of flowable resin composite. The simulated cuspal deflection caused by the polymerization of resin composite within an aluminium block was measured using a highly accurate submicron digimatic micrometer or a confocal laser scanning microscope (CLSM). In addition, the flexural properties of tested resin composites were measured to investigate the relation between cuspal deflection and flexural properties, and the resin composites were observed using scanning electron microscopy.Results: Simulated cuspal deflection of some bulk-fill flowable resin composites was found to be significantly lower than or similar to those for conventional counterparts, regardless of the measurement method. There were statistically significant differences in flexural properties depending on the material, regardless of the type of flowable resin composite. Pearson correlation analysis did not reveal a statistically significant relationship between flexural properties and cuspal deflection.Conclusion: These results indicate that some bulk-fill flowable resin composites exhibit lower cuspal deflection with the bulk-filling technique than is shown by conventional flowable resin composites using the incremental filling technique. Simulated cuspal deflection can be measured using either a micrometer or CLSM, but this experiment failed to show a significant relationship between cuspal deflection and flexural properties of flowable resin composites.

AB0381 THE UTILITY OF HYDROXYCHLOROQUINE (HCQ) THERAPY FOR TWO YEARS AS A SPARING CORTICOSTEROID AGENCY IN PATIENTS WITH SYSTEMIC LUPUS ERYTHEMATOSUS (SLE)

Background:

Prednisolone (PSL) and HCQ are key drugs in the therapy of SLE. However, since PSL induce many harmful adverse events, PSL is preferred to be reduced especially in the maintenance therapy. The efficacy of HCQ for reducing the dose of PSL has not been revealed yet. So, we focused on the cessation of PSL under the treatment of HCQ with conventional SLE therapy.

Objectives:

The aim of this study is to evaluate the efficacy and the safety of HCQ as co-treatment in the standard therapy of SLE.

Methods:

SLE patients (n=30) under the maintenance therapy were enrolled in this study. Dose of PSL, titer of anti-DNA antibody, WBC count, serum complement and SLE disease activity index (SLEDAI) were examined retrospectively at 0 and 12 months after administration of HCQ.

Results:

Baseline patient-characteristics are as follows (mean±S.E); the age of patients was 54.4±3.2 years old, 21 patients (70%) were female, the disease duration was 108.5±25.2 months, SLEDAI was 4.0±0.9, the dose of PSL was 10.3±1.7 mg/day, the titer of anti-DNA antibody was 7.3±1.8 IU/ml, C3 was 85±4.3 mg/dl and C4 was 18±1.6 mg/dl.

The mean dose of PSL was reduced with statistically significance (pre-administration of HCQ:10.3±1.7 mg/day, 24 months after administration of HCQ:2.2±0.3 mg/day,p<0.0001). Furthermore, in this observation period, 6 patients could achieve the cessation of PSL.

SLEDAI was also significantly reduced (4.0±0.9 vs 1.0±0.3,p<0.01).

There was no statistical significance between before treatment by HCQ and after treatment in the titer of anti-DNA antibody (7.3±1.8 vs 2.8±1.6 IU/ml,p=0.06), WBC count (6208±4.9 vs 5096±3.3 /μl,p=0.06) and serum complement level (C3 85±4.3 mg/dl vs 89±4.0 mg/dl,p=0.52, C4 18±1.6 mg/dl vs 19±1.4 mg/dl,p=0.45). Relapse of SLE was clarified in only one patient.

As for adverse events (AEs), Severe bacterial infection (n=4), herpes zoster (n=1) and patellar tendon rupture (n=1) were revealed. All cases of the AEs were fully recovered.

Conclusion:

Our study suggested that co-treatment with HCQ on standard SLE therapy could be enable to prevent the flare of SLE and reduce the dose of PSL with statistical significance. In some cases, we could achieve the cessation of PSL treatment.

References:

None.

Disclosure of Interests:

None declared

The Effects of Aluminablasting on Bond Durability Between Universal Adhesives and Tooth Substrate

The aim of this study was to determine the effect of aluminablasting on the bond durability of universal adhesives and adherent surface characteristics. Adhese Universal (Ivoclar Vivadent), All-Bond Universal (Bisco), Bondmer Lightless (Tokuyama Dental), G-Premio Bond (GC), and Scotchbond Universal (3M ESPE) were used in self-etch mode. The prepared bovine enamel and dentin specimens were divided into two groups based on whether they received an aluminablasting prior to application of the universal adhesives. The resin composite bonded specimens were stored in distilled water at 37°C for 24 hours, following which the shear bond strength (SBS) of half of the specimens was measured (24-hour group). The other half was subjected to 30,000 thermal cycles between 5 and 55°C before SBS measurement (TC group). Surface roughness (Ra) and surface free energy (SFE) of the adherent surfaces were also measured, and scanning electron microscopy observation and scanning electron microscopy/energy-dispersive X-ray analysis were carried out. Most of the adhesives did not show any significant differences in enamel SBS values between the two pretreatment groups, regardless of the storage condition. However, the dentin SBS values were significantly lower in specimens that underwent aluminablasting compared with those that did not, irrespective of their storage conditions. Significantly higher Ra and SFE values were observed in the enamel and dentin of specimens that underwent aluminablasting. Although aluminablasting increased the Ra and SFE values of enamel and dentin, its effect on the SBS value was dependent on the tooth substrate. In addition to C, O, Na, Mg, P, and Ca, the element Al was detected in the enamel and dentin of samples that had undergone aluminablasting. These results suggest that although aluminablasting of the tooth surface is thought to be effective for modification of the adherent surface, it may not enhance enamel bond performance and may also adversely affect the dentin bond effectiveness of the universal adhesives.

Effects of Finishing and Polishing Methods on the Surface Roughness and Surface Free Energy of Bulk-fill Resin Composites

The purpose of this study was to determine the influence of finishing and polishing methods on surface properties of bulk-fill resin composites through surface roughness (Ra) and surface free energy (SFE) measurements, and scanning electron microscopy (SEM) observations. Three bulk-fill resin composites, Tetric EvoCeram Bulk Fill (TB), Filtek Bulk Fill (FB), and Filtek Bulk Fill Flowable Restorative (FF), and two conventional resin composites, Clearfil AP-X (AP) and Estelite ∑ Quick (EQ) were used. Seventy cured specimens of each resin composite were prepared and divided into seven groups of 10 specimens. Ra, SFE measurements, and SEM observations were conducted after finishing and polishing procedures. Three groups of specimens were finished with a fine grit diamond bur (FDB), and three with a tungsten carbide bur (CBB). After finishing, one group from each type of finishing was polished with aluminum oxide flexible disks (SSD) and one group from each type of finishing was polished with diamond particles embedded in a silicone point (CMP). A baseline group of samples that were neither finished nor polished after removing the translucent strips from the surface was examined. Although the baseline group showed significantly lower Ra values than the other groups, most resin composites showed lower Ra values with CBB+SSD than with the other finishing and polishing groups. Among the tested resin composites, EQ showed significantly lower Ra values than the other resin composites, regardless of the finishing and polishing methods. On the other hand, AP showed significantly higher Ra values than the other resin composites in all finishing and polishing groups, apart from FB with FDB. For the finished specimens, most resin composites showed higher SFE values with CBB than with FDB. For the polished specimens, all the tested resin composites with CMP showed lower γ_S values than those with SSD, regardless of the finishing method. The baseline groups of TB and FB showed significantly lower SFE values than the other finished and polished groups. In the SEM observations, all the examined resin composites showed rougher surfaces after finishing with FDB than with CBB. However, when comparing the different polishing methods (CMP and SSD), surface smoothness appeared to be material dependent.

Influence of Application Time on Dentin Bond Performance in Different Etching Modes of Universal Adhesives

We attempted to determine the effect of universal adhesive application time on dentin bond performance in different etching modes based on shear bond strength (SBS) tests and surface free energy (SFE) measurements. The five universal adhesives used were Adhese Universal (AU), Clearfil Universal Bond Quick (CQ), G-Premio Bond (GP), Scotchbond Universal (SU), and Tokuyama Universal Bond (TU). Bovine dentin specimens were divided into four groups of 10 for each adhesive. SBS and SFE were determined after applying the following surface treatments: 1) self-etch (SE) mode with immediate air blowing after adhesive application (IA treatment), 2) SE mode with prolonged application time (PA treatment), 3) etch-and-rinse (ER) mode with IA treatment, and 4) ER mode with PA treatment. Bonded specimens were subjected to SBS testing. The SFE of adhesive-treated dentin surfaces was measured after rinsing with acetone and water. Three-way analysis of variance revealed that dentin SBS values (p<0.001) were significantly influenced by the factors of adhesive type and application duration, but the factor of pre-etching was not significant (p=0.985). The manufacturer's instructions require longer application times for AU and SU, which showed significantly lower SBS values in IA than in PA treatment in both etching modes. However, the difference in the other adhesives was not significant between the IA and PA treatments in either etching mode. The total SFE (γ_S) was dependent on the adhesive and etching mode. The γ_S value of the initial group (SiC paper ground group) at baseline was 69.5 (mN·m^-1) and that of the pre-etching group at baseline was 30.6 (mN·m^-1). For all the adhesives, γ_S in SE mode showed significantly higher values than in ER mode, regardless of the application time. In SE mode, almost all universal adhesives tested showed lower γ_S values in PA treatment than in IA treatment. For ER mode, all the adhesives showed significantly higher γ_S values than those of the pre-etching baseline, regardless of the application time. Most adhesives did not show any significant differences in γ_S values between IA and PA treatments, regardless of etching mode.

CD73 complexes with emmprin to regulate MMP-2 production from co-cultured sarcoma cells and fibroblasts

Background

Interaction between cancer cells and fibroblasts mediated by extracellular matrix metalloproteinase inducer (emmprin, CD147) is important in the invasion and proliferation of cancer cells. However, the exact mechanism of emmprin mediated stimulation of matrix metalloprotease-2 (MMP-2) production from fibroblasts has not been elucidated. Our previous studies using an inhibitory peptide against emmprin suggested the presence of a molecule on the cell membrane which forms a complex with emmprin. Here we show that CD73 expressed on fibroblasts interacts with emmprin and is a required factor for MMP-2 production in co-cultures of sarcoma cells with fibroblasts.

Methods

CD73 along with CD99 was identified by mass spectrometry analysis as an emmprin interacting molecule from a co-culture of cancer cells (epithelioid sarcoma cell line FU-EPS-1) and fibroblasts (immortalized fibroblasts cell line ST353i). MMP-2 production was measured by immunoblot and ELISA. The formation of complexes of CD73 with emmprin was confirmed by immunoprecipitation, and their co-localization in tumor cells and fibroblasts was shown by fluorescent immunostaining and proximity ligation assays.

Results

Stimulated MMP-2 production in co-culture of cancer cells and fibroblasts was completely suppressed by siRNA knockdown of CD73, but not by CD99 knockdown. MMP-2 production was not suppressed by CD73-specific enzyme inhibitor (APCP). However, MMP-2 production was decreased by CD73 neutralizing antibodies, suggesting that CD73-mediated suppression of MMP-2 production is non-enzymatic. In human epithelioid sarcoma tissues, emmprin was immunohistochemically detected to be mainly expressed in tumor cells, and CD73 was expressed in fibroblasts and tumor cells: emmprin and CD73 were co-localized predominantly on tumor cells.

Conclusion

This study provides a novel insight into the role of CD73 in emmprin-mediated regulation of MMP-2 production.

Effect of a saline flush technique for head and neck imaging in dual-energy CT: improvement of image quality and perivenous artefact reduction using virtual monochromatic imaging

AIM

To evaluate the effect of the saline flush (SF) technique on the depiction of lesions and the reduction of perivenous artefacts in the head and neck region using dual-energy computed tomography (CT) with virtual monochromatic imaging (VMI).

MATERIALS AND METHODS

Fifty patients with head and neck cancer were divided into two groups: group A, without a SF and group B, with a 30-ml SF. All images were acquired using fast kilovolt-switching CT (Revolution HD, GE Healthcare, Milwaukee, WI, USA). Contrast-to-noise ratios (CNRs) of the lesions were calculated at VMI energy levels ranging from 40 to 80 keV. Subjective analysis of overall image quality, delineation of lesions, and perivenous artefacts was conducted by two reviewers at both VMI energy level 40 keV and the optimal energy level (which showed optimal CNR by objective analysis).

RESULTS

Optimal energy level was 63 keV for group A and 61 keV for group B. At VMI energy levels ranging from 40 to 80 keV, the CNR was higher for group B. The highest subjective overall image quality was shown for group B at the optimal energy level (subjective image quality mean value, 3.40). Subjective delineation of lesions was comparable. The perivenous artefact score was significantly higher for group B (2.44 versus 2.74 [p<0.05] at 40 keV, 3.20 versus 3.46 [p<0.05] at the optimal energy level).

CONCLUSION

The SF technique results in an improvement of lesion CNR and a reduction of perivenous artefacts in VMI using duel-energy CT, especially at 40 keV.