Electrical and optical properties of NiO composite films by radio frequency magnetron sputtering

The 100-nm NiO-Ag composite films with Ag content of 0 to 24.4 at.% are deposited on glass substrates. It is found that an ultra high electric resistivity (rho) value is obtained and cannot be detected by four point probe measurement when the Ag content is less than 3.4 at.%. The rho value is reduced significantly to 29.0 Omega-cm as Ag content is increased to 4.2 at.%, and it decreases greatly to 0.009 Omega-cm as the content of Ag is further increased to 24.4 at.%. The NiO-Ag composite film with Ag content of 4.2 at.% shows p-type conduction. However, it becomes n-type when the Ag content increases to 9.3 at.%, which results from the Ag atoms segregated at grain boundary of NiO when the excess Ag atoms are added into NiO films. On the other hand, the transmittance of the NiO-Ag films drops continuously from 96.3% to 31.6% as the Ag content increases from 0 to 24.4%.

Effect of Ag underlayer on microstructures and perpendicular magnetic properties of CoPt nanocomposite thin films

CoPt/Ag films were prepared by magnetron sputtering on glass substrates and subsequent annealing. The dependence of degree of ordering and magnetic properties on Ag film thickness and annealing conditions were investigated. It was found that the Ag underlayer played a dominant role in inducing the (001) texture of the CoPt film after annealing. CoPt films with a thickness about 20 nm and Ag underlayers with a thickness about 70 nm are easy to obtain a large degree of ordering and a perpendicular magnetic anisotropy after annealing at 700 degrees C for 30 min. CoPt/Ag films with out-of-plane coercivity (Hc (perpendicular)) in the range of 13.5-14.0 kOe and a out-of-plane squareness (S(perpendicular)) of 0.97 were obtained after annealing at 700 degrees C for 30 min. Ag underlayer is beneficial to enhance the Hc(perpendicular)and S(perpendicular) of CoPt film significantly. The degree of ordering and perpendicular magnetic properties of the CoPt films which deposited on Ag underlayer are larger than those of the single layer CoPt films.

Crystallization mechanisms of phase change (GeSbSn)(100-x)Co(x) optical recording films

In this study, the (GeSbSn)(100-x0Co(x) films (x = 0-13.3) were deposited on natural oxidized silicon wafer and glass substrate by dc magnetron co-sputtering of GeSbSn and Co targets. The ZnS-SiO2 films were used as protective layers. The thicknesses of the (GeSbSn)(100-x)Co(x) films and protective layer were 100 nm and 30 nm, respectively. We investigated the effects of Co addition on the thermal property, crystallization kinetics, and crystallization mechanism of the GeSbSn recording film. The crystallization temperatures of (GeSbSn)(100-x)Co(x) films were decreased with Co content. It was found that the activation energy of the (GeSbSn)(100-x)Co(x) films will decrease from 1.53 eV to 0.55 eV as Co content increased from 0 at.% to 13.3 at.%.

Microstructure and crystallization kinetics analysis of the (In15Sb85)(100-x)Zn(x) phase change recording thin films

The (In15Sb85)(100-x)Zn(x) films (x = 0 - 17.4) were deposited on nature oxidized Si wafer and glass substrate at room temperature by magnetron co-sputtering of Sb target and InZn composite target. The thermal property of the films was examined by a homemade reflectivity thermal analyzer. Microstructures of the films were analyzed by transmission electron microscope (TEM). We examined the effects of Zn addition on the thermal property, crystallization kinetics, and crystallization mechanism of the In15Sb85 recording film. As x = 0 - 17.4, thermal analysis shows that the (In15Sb85)(100-x)Zn(x) films have two phase transition temperature ranges which are 189 degrees C-215 degrees C and 300 degrees C-350 degrees C. It is found that the activation energy is increased with Zn content. This indicates that the thermal stability of amorphous state is improved by doping Zn. The optical contrasts of the films are all larger than 15%, as x = 0 - 6.2, indicating that the films have the potential in blue laser optical recording media application.

Differential gene expression between the porcine morula and blastocyst

The survival and development of pre-implantation embryos are determinant factors affecting the outcome of animal reproduction. It is essential to transfer the expression of the genetic material from maternal sources, that is the ovum to the zygote before implantation to ensure successful development. Differentiation and transformation of blastomeres initiated during the morula and blastocyst stages is an important step of the embryonic development prior to implantation. We collected morula and early blastocyst samples from pure-bred Landrace pigs in vivo to study the differential gene expression patterns at these two stages. Total RNA was extracted from individual embryos and two rounds of amplification were employed. Two micrograms of antisense RNA, targets, were prepared and hybridized with each of four custom made oligo microarrays representing 24,000 porcine genes. The analyses of replicate hybridizations showed that among the 24,000 genes, 162 genes were expressed fivefold or greater in the morula compared to early blastocysts and 2126 genes were expressed fivefold or greater in early blastocysts compared to the morula. Of these differentially expressed genes, 1429 genes were functionally annotated with related human Gene Ontology terms. In addition to basic metabolic processes, genes related to signal transduction, transportation and cell differentiation were found in both stages and were up-regulated as embryo development proceeded. Real time polymerase chain reaction was utilized to quantify 12 genes differentially expressed in the 2 embryonic stages and validated the reliability of major evidences shown in microarrays. In conclusion, we have obtained a preliminary landscape of genes differentially expressed during the transition from morula to early blastocysts in pigs and showed a generally increased transcriptional activity, perhaps in preparation for implantation. Our results provide an opportunity to study the functions of these genes in relation to the development and survival of pre-implantation porcine embryos.

Routine drainage is not necessary after laparoscopic gastric bypass

INTRODUCTION

Routine intra-abdominal drainage has been recommended for detecting surgical complications, such as anastomotic leaks or intra-abdominal hemorrhage, after laparoscopic gastric bypass for morbid obesity. The aim of this study was to determine whether routine drainage after laparoscopic gastric bypass is indeed necessary.

METHODS

Patients undergoing laparoscopic gastric bypass with intra-abdominal drainage (D-group) were compared with those without drainage (N-group) in a retrospective study. The main outcome measures were postoperative course and complications.

RESULTS

No differences were observed in the postoperative complications. Both groups had one major complication of leakage (1/90, 1.1%). Minor complications occurred in six D-group patients (6/90, 6.7%) and eight N-group patients (8/90, 8.9%) (P=0.578). No difference was observed in postoperative analgesic dose usage (mean ± SD: 63 ± 37 mg vs 60 ± 31 mg; P=0.963) or length of stay hospital (5.2 ± 2.6 d vs 4.7 ± 1.8 d; P=0.135). However, the N-group had a shorter time to flatus passage compared to the D-group (1.6 ± 0.7 d vs 1.2 ± 0.5 d; P=0.006).

CONCLUSION

Routine abdominal drainage is not necessary after a successful laparoscopic gastric bypass for morbidly obese patients. Drainage omission may contribute to a quicker recovery without additional surgical complications.

The effect of thickness on the texture and magnetic properties of single-layered FePt films by rapid thermal annealing

The single-layered FePt films with thickness in the range of 5 to 50 nm are deposited directly on Si(100) substrate without underlayer, then post annealed at 700 degrees C by rapid thermal annealing (RTA) technique. As the film thickness of FePt is over 20 nm, the L1(0) FePt(111) preferred orientation is presented and tended to in-plane magnetic anisotropy. However, the L1(0) FePt(001) texture is obtained and exhibited perpendicular magnetic anisotropy as the film thickness is decreased to 10 nm. Its perpendicular coercivity (Hc(perpendicular)), saturation magnetization (Ms) and perpendicular squareness (S(perpendicular)) are 14.8 kOe, 795 emu/cm3 and 0.79, respectively. On the other hand, both the grain size and domain size of FePt film decrease with decreasing the film thickness of FePt. The grain size for 10-nm FePt film is as small as 9.7 nm with domain size of 123 nm, which reveal its significant potential as perpendicular magnetic recording media for ultra high-density recording.

Discrete cortical responses from multi-site supra-choroidal electrical stimulation in the feline retina

Exploration into electrical stimulation of the retina has thus far focussed primarily upon the development of prostheses targeted at one of two sites of intervention - the epi- and sub-retinal surfaces. These two approaches have sound, logical merit owing to their proximity to retinal neurons and their potential to deliver stimuli via the surviving retinal neural networks respectively. There is increasing evidence, however, that electric field effects, electrode engineering limitations, and electrode-tissue interactions limit the spatial resolution that once was hoped could be elicited from electrical stimulation at epi- and sub-retinal sites. An alternative approach has been proposed that places a stimulating electrode array within the supra-choroidal space - that is, between the sclera and the choroid. Here we investigate whether discrete, cortical activity patterns can be elicited via electrical stimulation of a feline retina using a custom, 14 channel, silicone rubber and Pt electrode array arranged in two hexagons comprising seven electrodes each. Cortical responses from Areas 17/18 were acquired using a silicon-based, multi-channel, penetrating probe developed at IMTEK, University of Freiburg, within the European research project NeuroProbes. Multi-unit spike activity was recorded in synchrony with the presentation of electrical stimuli. Results show that distinct cortical response patterns could be elicited from each hexagon separated by 1.8 mm (center-to-center) with a center-to-center electrode spacing within each hexagon of 0.55 mm. This lends support that higher spatial resolution may also be discerned.

A transparent electrode array for simultaneous cortical potential recording and intrinsic signal optical imaging

Intrinsic signal optical imaging (ISOI) is a technique that enables researchers to relate changes in cortical activity in response to stimuli by measuring changes in hemoglobin oxygenation and local blood volume. As the time course of these changes - local blood volume in particular - is of the order of seconds, the neural activity that initiates these changes is only indirectly acquired in ISOI. To better correlate these events, it is beneficial to simultaneously record both the evoked cortical potentials and ISOI. In this study we present a novel, transparent, recording array that allows the combination of optical imaging with electrical recordings without the use of metal electrodes in the observation field. Pilot data were recorded after visual and electrical stimuli of the eye to prove the concept.

Analysis of the factors influencing living kidney donation: the experience in National Taiwan University Hospital

INTRODUCTION

Kidney transplantation provides a choice of active treatment for patients with chronic renal failure. However, the sources of organs are limited; therefore, living kidney donation is an alternative source. The regulation of organ donation in Taiwan stipulates that living organ donation is restricted to living related recipients. We sought to investigate factors that influenced or prevented individuals from living kidney donation in our center.

MATERIALS AND METHODS

From January 2005 to December 2008, there were 266 potential candidates who underwent evaluation for living kidney donation in our center.

RESULTS

Among the potential candidates, most were spouses (n=85, 31.9%), followed by parents (n=67, 25.1%), siblings (n=62, 23.3%), and children (n=40, 15%). Eventually, 124 candidates (47%) completed organ donation, most of whom were siblings (n=39, 31.5%), then parents (n=38, 30.6%), spouses (n=26), and children (n=18). Most donors were females, including mothers and sisters. The most frequent reason to not donate was unwillingness, due to potential influences on their health, economic stress due to suspension of their job, and objection of family members. In 34 candidates (23.9%), adverse health factors of potential candidates prohibited them from donating, including age, chronic medical illness, hepatitis carrier status, severe depression, or mental retardation. Among 59 potential donor-recipient pairs with incompatible ABO blood types or highly sensitized to potential donors, 22 candidates completed living kidney donation.

CONCLUSION

Although laparoscopic nephrectomy for living kidney donation decreases the discomfort and hospital stay after donation, we can only promote living kidney donation if we can deal with the possible factors that prohibit candidates from living kidney donation, such as morbidity after organ donation, anxiety, or other factors. After analyzing those factors, we must also develop a protocol to closely follow the living kidney donors to ensure their health status and relieve their anxiety.

Biodegradation of propionitrile by Klebsiella oxytoca immobilized in alginate and cellulose triacetate gel

A microbial process for the degradation of propionitrile by Klebsiella oxytoca was studied. The microorganism, K. oxytoca, was isolated from the discharged wastewater of metal plating factory in southern Taiwan and adapted for propionitrile biodegradation. The free and immobilized cells of K. oxytoca were then examined for their capabilities on degrading propionitrile under various conditions. Alginate (AL) and cellulose triacetate (CT) techniques were applied for the preparation of immobilized cells. The efficiency and produced metabolic intermediates and end-products of propionitrile degradation were monitored in bath and continuous bioreactor experiments. Results reveal that up to 100 and 150 mM of propionitrile could be removed completely by the free and immobilized cell systems, respectively. Furthermore, both immobilized cell systems show higher removal efficiencies in wider ranges of temperature (20-40 degrees C) and pH (6-8) compared with the free cell system. Results also indicate that immobilized cell system could support a higher cell density to enhance the removal efficiency of propionitrile. Immobilized cells were reused in five consecutive degradation experiments, and up to 99% of propionitrile degradation was observed in each batch test. This suggests that the activity of immobilized cells can be maintained and reused throughout different propionitrile degradation processes. A two-step pathway was observed for the biodegradation of propionitrile. Propionamide was first produced followed by propionic acid and ammonia. Results suggest that nitrile hydratase and amidase were involved in the degradation pathways of K. oxytoca. In the continuous bioreactor, both immobilized cells were capable of removing 150 mM of propionitriles completely within 16h, and the maximum propionitriles removal rates using AL and CT immobilized beads were 5.04 and 4.98 mM h(-1), respectively. Comparing the removal rates obtained from batch experiments with immobilized cells (AL and CT were 1.57 and 2.18 mM h(-1) at 150 mM of propionitrile, respectively), the continuous-flow bioreactor show higher potential for practical application.

Synergistic antitumor effect of TRAIL and adriamycin on the human breast cancer cell line MCF-7

The aim of the present study was to determine the effect of the combination of tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) and adriamycin (ADM) on the human breast cancer cell line MCF-7 and to identify potential mechanisms of apoptosis. Cell viability was analyzed by the MTT assay and the synergistic effect was assessed by the Webb coefficient. Apoptosis was quantified using the annexin V-FITC and propidium iodide staining flow cytometry. The mRNA expression of TRAIL receptors was measured by RT-PCR. Changes in the quantities of Bax and caspase-9 proteins were determined by Western blot. MCF-7 cells were relatively resistant to TRAIL (IC50 >10 microg/mL), while MCF-7 cells were sensitive to ADM (IC50 <10 microg/mL). A subtoxic concentration of ADM (0.5 microg/mL) combined with 0.1, 1, or 10 microg/mL TRAIL had a synergistic cytotoxic effect on MCF-7 cells, which was more marked with the combination of TRAIL (0.1 microg/mL) and ADM (0.5 microg/mL). In addition, the combined treatment with TRAIL and ADM significantly increased cell apoptosis from 9.8% (TRAIL) or 17% (ADM) to 38.7%, resulting in a synergistic apoptotic effect, which is proposed to be mediated by up-regulation of DR4 and DR5 mRNA expression and increased expression of Bax and caspase-9 proteins. These results suggest that the combination of TRAIL and ADM might be a promising therapy for breast cancer.

Combined immersion and oral vaccination of Vietnamese catfish (Pangasianodon hypophthalmus) confers protection against mortality caused by Edwardsiella ictaluri

Edwardsiella ictaluri septicemia occurs worldwide and causes high mortality and considerable economic damage to the catfish industry especially in Vietnam and the USA. To control Edwardsiella septicemia farmers extensively use antibiotics and various vaccination methods. Vaccination with inactivated vaccines has come with variable efficacy. In this trial the results of an approach of controlling Edwardsiella septicemia of Tra catfish (Pangasianodon hypophthalmus) in Vietnam through vaccination via mucosal surfaces are presented. The results show that a combination of primary vaccination by immersion with inactivated E. ictaluri followed by an oral boost with a formulated antigen preparation induces a statistically significant level of protection against mortality caused by experimental infection 4 weeks post-boost. Fish immunized by immersion only show significantly lower level of protection but significantly higher than the controls. Repeated boosts result in improved duration of immunity with a relative percent survival (RPS) of 47% at 90% control mortality. The immunization procedure provides an alternative for disease control through vaccination.

An experimental method to verify soil conservation by check dams on the Loess Plateau, China

A successful experiment with a physical model requires necessary conditions of similarity. This study presents an experimental method with a semi-scale physical model. The model is used to monitor and verify soil conservation by check dams in a small watershed on the Loess Plateau of China. During experiments, the model-prototype ratio of geomorphic variables was kept constant under each rainfall event. Consequently, experimental data are available for verification of soil erosion processes in the field and for predicting soil loss in a model watershed with check dams. Thus, it can predict the amount of soil loss in a catchment. This study also mentions four criteria: similarities of watershed geometry, grain size and bare land, Froude number (Fr) for rainfall event, and soil erosion in downscaled models. The efficacy of the proposed method was confirmed using these criteria in two different downscaled model experiments. The B-Model, a large scale model, simulates watershed prototype. The two small scale models, D(a) and D(b), have different erosion rates, but are the same size. These two models simulate hydraulic processes in the B-Model. Experiment results show that while soil loss in the small scale models was converted by multiplying the soil loss scale number, it was very close to that of the B-Model. Obviously, with a semi-scale physical model, experiments are available to verify and predict soil loss in a small watershed area with check dam system on the Loess Plateau, China.

Patient-driven loop control for ambulation function restoration in a non-invasive functional electrical stimulation system

PURPOSE

In this study, a patient-driven loop control in a non-invasive functional electrical stimulation (FES) system was designed to restore ambulation function of patients with stroke with their residual capabilities.

METHOD

With this patient-driven loop control, patients use the electromyographic (EMG) signals from their voluntary controlled muscles in affected extremity to adjust stimulus parameters of the system. A special designed FES system generated electrical stimuli to excite the paralysed muscles through surface electrodes on the basis of the control command from the residual myoelectric signals. The EMG signals were also served as the trigger and the adjustment of stimulus parameters and thereby adding versatility of the FES system. One patient with hemiplegia was recruited to conduct clinical evaluation and treated by using the new closed-loop FES system.

RESULTS

The experimental results showed that hemiplegic could successfully control the system to restore their lost ambulation functions with the strategy of patient-driven loop control. It is revealed that the mean velocity, cadence, stride length, active ankle motion range and functional ambulation category have improved significantly from 0.22 + or - 0.17 m/s, 37.3 + or - 15.5 steps/min, 0.32 + or - 0.11 m, 10 degrees , level 2 to 0.46 + or - 0.23 m/s, 58.2 + or - 19.1 steps/min, 0.73 + or - 0.22 m, 35 degrees , level 4 respectively for the patient. A paired t-test indicated that differences in the EMG of the tibialis anterior and the gastrocnemius muscles between patient's disabled (affected-side) foot and normal (unaffected-side) foot are not significant (p > 0.05) after 12 weeks of training.

CONCLUSIONS

According to the experiment results, this patient-driven loop control can be beneficial for patient with hemiplegia to restore their ambulation functions such as dorsi-flexion and plantar-flexion. The control strategy of this study has the potential to be employed not only in the FES system but also in other assistive devices.

Viral kinetics and exhaled droplet size affect indoor transmission dynamics of influenza infection

The purpose of this paper was to investigate the effects of viral kinetics and exhaled droplet size on indoor transmission dynamics of influenza infection. The target cell-limited model with delayed virus production was adopted to strengthen the inner mechanisms of virus infection on human epithelial cell. The particle number and volume involved in the viral kinetics were linked with Wells-Riley mathematical equation to quantify the infection risk. We investigated population dynamics in a specific elementary school by using the seasonal susceptible - exposed - infected - recovery (SEIR) model. We found that exhaled pulmonary bioaerosol of sneeze (particle diameter <10 microm) have 10(2)-fold estimate higher than that of cough. Sneeze and cough caused risk probabilities range from 0.075 to 0.30 and 0.076, respectively; whereas basic reproduction numbers (R(0)) estimates range from 4 to 17 for sneeze and nearly 4 for cough, indicating sneeze-posed higher infection risk. The viral kinetics and exhaled droplet size for sneeze affect indoor transmission dynamics of influenza infection since date post-infection 1-7. This study provides direct mechanistic support that indoor influenza virus transmission can be characterized by viral kinetics in human upper respiratory tracts that are modulated by exhaled droplet size. Practical Implications This paper provides a predictive model that can integrate the influenza viral kinetics (target cell-limited model), indoor aerosol transmission potential (Wells-Riley mathematical equation), and population dynamic model [susceptible - exposed - infected - recovery (SEIR) model] in a proposed susceptible population. Viral kinetics expresses the competed results of human immunity ability with influenza virus generation. By linking the viral kinetics and different exposure parameters and environmental factors in a proposed school setting with five age groups, the influenza infection risk can be estimated. On the other hand, we implicated a new simple means of inhaling to mitigate exhaled bioaerosols through an inhaled non-toxic aerosol. The proposed predictive model may serve as a tool for further investigation of specific control measure such as the personal protection masks to alter the particle size and number concentration characteristics and minimize the exhaled bioaerosol droplet to decrease the infection risk in indoor environment settings.

Rehabilitation regimes based upon psychophysical studies of prosthetic vision

Human trials of prototype visual prostheses have successfully elicited visual percepts (phosphenes) in the visual field of implant recipients blinded through retinitis pigmentosa and age-related macular degeneration. Researchers are progressing rapidly towards a device that utilizes individual phosphenes as the elementary building blocks to compose a visual scene. This form of prosthetic vision is expected, in the near term, to have low resolution, large inter-phosphene gaps, distorted spatial distribution of phosphenes, restricted field of view, an eccentrically located phosphene field and limited number of expressible luminance levels. In order to fully realize the potential of these devices, there needs to be a training and rehabilitation program which aims to assist the prosthesis recipients to understand what they are seeing, and also to adapt their viewing habits to optimize the performance of the device. Based on the literature of psychophysical studies in simulated and real prosthetic vision, this paper proposes a comprehensive, theoretical training regime for a prosthesis recipient: visual search, visual acuity, reading, face/object recognition, hand-eye coordination and navigation. The aim of these tasks is to train the recipients to conduct visual scanning, eccentric viewing and reading, discerning low-contrast visual information, and coordinating bodily actions for visual-guided tasks under prosthetic vision. These skills have been identified as playing an important role in making prosthetic vision functional for the daily activities of their recipients.

Predictors of mortality in patients with pyogenic liver abscess

BACKGROUND

Pyogenic liver abscess (PLA) is uncommon but potentially life-threatening. The objective of this study was to identify the prognostic factors for PLA.

METHODS

The medical records of 253 patients, 148 men and 105 women with a mean age of 56.4 years (SD : 15.0 years), who were hospitalised due to a PLA between January 1995 and June 2007 were reviewed. The underlying medical disorders, clinical signs and symptoms, laboratory values, imaging studies, microbiological features, treatments, morbidity and mortality were recorded. Factors related to in-hospital case fatality were analysed.

RESULTS

The mean Acute Physiology And Chronic Health Evaluation (APACHE) II score at admission in patients with PLA was 8.7 points (SD 5.4 points). The most common co-existing disease was diabetes mellitus (41.9%), followed by biliary stone disorders (32.0%). Klebsiella pneumoniae was the most frequent pathogen, followed by Escherichia coli. The in-hospital case-fatality rate was 9.1%. Multivariate analysis revealed that gas-forming abscess (p=0.019), multi-drug resistant isolates (p=0.026), anaerobic infection (p=0.045), blood urea nitrogen level >7.86 mmol/l (p=0.004), and APACHE II score > or =15 (p= 0.004) were associated with mortality.

CONCLUSIONS

The prognosis of PLA may depend chiefly on the severity of the basic physical condition and underlying pathology. As the primary treatment for PLA is not completely effective, a more aggressive approach should be considered, especially for patients with poor prognosis.

Application of Klebsiella oxytoca immobilized cells on the treatment of cyanide wastewater

Klebsiella oxytoca, isolated from cyanide-containing industrial wastewater, has been shown to be able to biodegrade cyanide to non-toxic end products. The technology of immobilized cells can be applied in biological treatment to enhance the efficiency and effectiveness of biodegradation. In this study, potassium cyanide was used as the target compound and both alginate and cellulose triacetate techniques were applied for the preparation of immobilized cells. Results from this study show that KCN can be utilized as the sole nitrogen source by K. oxytoca. The free suspension systems reveal that the cell viability was highly affected by initial KCN concentration and pH. Results show that immobilized cell systems could tolerate a higher level of KCN concentration and wider ranges of pH. In the batch experiments, the maximum KCN removal efficiencies using alginate and cellulose triacetate immobilized beads were 0.108 and 0.101mM h(-1) at pH 7, respectively. Results also indicate that immobilized system can support a higher biomass concentration. Complete KCN degradation was observed after the operation of four consecutive degradation experiments with the same batch of immobilized cells. This suggests that the activity of immobilized cells can be maintained and KCN can be used as the nitrogen source throughout KCN degradation experiments. The maximum KCN removal rates using alginate and cellulose triacetate immobilized beads in continuous-column system were 0.224 and 0.192mMh(-1) with initial KCN concentration of 3mM, respectively. Results indicate that the immobilized cells of K. oxytoca would be applicable to the treatment of cyanide-containing wastewaters.

Application of in situ biosparging to remediate a petroleum-hydrocarbon spill site: field and microbial evaluation

In this study, a full-scale biosparging investigation was conducted at a petroleum-hydrocarbon spill site. Field results reveal that natural attenuation was the main cause of the decrease in major contaminants [benzene, toluene, ethylbenzene, and xylenes (BTEX)] concentrations in groundwater before the operation of biosparging system. Evidence of the occurrence of natural attenuation within the BTEX plume includes: (1) decrease of DO, nitrate, sulfate, and redox potential, (2) production of dissolved ferrous iron, sulfide, methane, and CO(2), (3) decreased BTEX concentrations along the transport path, (4) increased microbial populations, and (5) limited spreading of the BTEX plume. Field results also reveal that the operation of biosparging caused the shifting of anaerobic conditions inside the plume to aerobic conditions. This variation can be confirmed by the following field observations inside the plume due to the biosparging process: (1) increase in DO, redox potential, nitrate, and sulfate, (2) decrease dissolved ferrous iron, sulfide, and methane, (3) increased total cultivable heterotrophs, and (4) decreased total cultivable anaerobes as well as methanogens. Results of polymerase chain reaction, denaturing gradient gel electrophoresis, and nucleotide sequence analysis reveal that three BTEX biodegraders (Candidauts magnetobacterium, Flavobacteriales bacterium, and Bacteroidetes bacterium) might exist at this site. Results show that more than 70% of BTEX has been removed through the biosparging system within a 10-month remedial period at an averaged groundwater temperature of 18 degrees C. This indicates that biosparging is a promising technology to remediate BTEX contaminated groundwater.

Surface plasmon-based nanopatterning assisted by gold nanospheres

A pulsed laser is used to produce surface plasmon excitation in a monolayer of gold (Au) spheres to nanopattern a silicon substrate. An electrodynamic model accompanies the experimental data, based on the numerical solution to the complete Maxwell's equations including near- and far-field effects and reflection from the substrate. The Drude-employing finite-difference time-domain method describes the deformation and enhancement of the laser pulse around the boundary of a Au sphere and the resulting distribution of intensity incident upon the substrate. The effect of the incident laser angle on the plasmon generation and lithographic potential is studied.

Efficacy of supra-choroidal, bipolar, electrical stimulation in a vision prosthesis

The key to successful, clinical application of therapeutic neurostimulators lies primarily with the safety and efficacy of their electrode-tissue interfaces. The authors posit that for electrical stimulation of the visual system, supra-choroidal electrode placement provides a safe, stable and readily-accessible site for implantation and the provision of electrical stimulation. The present paper explores the efficacy of supra-choroidal electrical stimulation of retinal neurons. Based upon recordings made with surface electrodes placed on the primary visual cortex, areas of activation in the cortex were shown to change when different areas on the supra-choroidal space were stimulated. Finally, the threshold to elicit a response from neurons in the visual cortex, was found to be 77.55 +/- 29.85 nC.

A text input system developed by using lips image recognition based LabVIEW for the seriously disabled

In this paper, we present a text input system for the seriously disabled by using lips image recognition based on LabVIEW. This system can be divided into the software subsystem and the hardware subsystem. In the software subsystem, we adopted the technique of image processing to recognize the status of mouth-opened or mouth-closed depending the relative distance between the upper lip and the lower lip. In the hardware subsystem, parallel port built in PC is used to transmit the recognized result of mouth status to the Morse-code text input system. Integrating the software subsystem with the hardware subsystem, we implement a text input system by using lips image recognition programmed in LabVIEW language. We hope the system can help the seriously disabled to communicate with normal people more easily.