Effect of Root Canal Treatments on Quartz Fiber Posts Bonding to Root Dentin

The aim of this study was to evaluate the effect of irrigants and endodontic sealers on fiber post push-out strength in both fatigue cycling and no-cycling conditions. Fifty single-rooted human teeth received five endodontic treatments. The posts were cemented using a flowable composite and a three-steps adhesive. Five specimens from each group were subjected to 2 x 10(6) cycles of 37.5 N. There were 200 sections obtained for the push-out test. Fatigue cycled groups treated with an eugenol-containing sealer showed the lowest push-out strength (p < 0.001). No significant differences were found among no-cycled groups (p = 0.665). The post-cement interface was found to be weaker than the cement-dentin one. However, fatigue cycles increased the occurrence of cement-dentin failures (p = 0.001). The eugenol-containing sealer reduced the bonding of fiber posts when mechanically cycled, thus the use of a resin-based sealer is advisable.

Push-out bond strengths: the Epiphany-Resilon endodontic obturation system compared with different pairings of Epiphany, Resilon, AH Plus and gutta-percha

AIM

To assess the bond strength of the new resin-based Epiphany-Resilon root canal filling system, and to compare this with bond strengths of different pairings of AH Plus, gutta-percha, Epiphany and Resilon.

METHODOLOGY

A total of 65 extracted human single-rooted teeth were used. All teeth were instrumented using a set of ProTaper rotary instruments. Irrigation was performed with 15 mL of 1.25% NaOCl between each instrument and the smear layer was removed during and after instrumentation with 5 mL of 17% EDTA. The canal spaces were filled with different combinations of core and sealer using lateral condensation, as follows: group 1, AH Plus + gutta-percha; group 2, AH Plus + Resilon; group 3, Epiphany + Resilon; group 4, Epiphany + gutta-percha; group 5 (control), gutta-percha only. Cylinders of root dentine 1.13 (0.06)-mm long were prepared from the coronal sections of the 65 teeth. The test specimens were subjected to the push-out test method. After adhesion testing, the remaining sections were examined under a stereomicroscope at x 25 magnification to determine the nature of bond failure. The values of bond strength were analyzed by one-way analysis of variance (ANOVA) and the post hoc Tukey's test, with significance set at P < 0.05.

RESULTS

The respective mean push-out test values for groups 1-5 were: 2.000 +/- 0.369, 1.380 +/- 0.154, 1.706 +/- 0.340, 2.857 +/- 0.523 and 0.078 +/- 0.027 MPa. Significant difference (P < 0.001) occurred between the groups. Multiple paired comparisons (Tukey's test) revealed that group 4 (Epiphany + gutta-percha) had significantly (P < 0.001) greater bonding strength than all the other groups; group 1 (AH Plus + gutta-percha) had significantly (P < 0.05) greater bonding strength than group 2 (AH Plus + Resilon); and group 5 (control) had significantly (P < 0.05) lower bonding strength than all the other groups. Inspection of the surfaces revealed the bond failure to be mainly adhesive to dentine for all groups.

CONCLUSIONS

The Epiphany-Resilon combination (group 3) was not superior to that of the AH Plus-gutta percha combination (group 1).

Root Canal Irrigants

Local wound debridement in the diseased pulp space is the main step in root canal treatment to prevent the tooth from being a source of infection. In this review article, the specifics of the pulpal microenvironment and the resulting requirements for irrigating solutions are spelled out. Sodium hypochlorite solutions are recommended as the main irrigants. This is because of their broad antimicrobial spectrum as well as their unique capacity to dissolve necrotic tissue remnants. Chemical and toxicological concerns related to their use are discussed, including different approaches to enhance local efficacy without increasing the caustic potential. In addition, chelating solutions are recommended as adjunct irrigants to prevent the formation of a smear layer and/or remove it before filling the root canal system. Based on the actions and interactions of currently available solutions, a clinical irrigating regimen is proposed. Furthermore, some technical aspects of irrigating the root canal system are discussed, and recent trends are critically inspected.

Evaluation of the accuracy of three electronic apex locators using glass tubules

AIM

To evaluate the accuracy of three different electronic apex locators (EALs) using glass tubules.

METHODOLOGY

Forty-eight glass tubules with different diameters and an agar model were used to mimic root canals. A size 15 stainless steel K-file was used as the measuring electrode. The Root ZX, Propex and Neosono Ultima EZ were used to measure the tubule length with tubules dry, or filled with 0.9% NaCl, 3% H(2)O(2), 2.5% NaOCl or 17% EDTA. The distance between the real length (RL) and measured length (ML) of the tubules was recorded. The range of RL +/- 0.5 mm and RL +/- 1 mm was used to evaluate the accuracy of the EALs. Results were subject to correlation analysis and Friedman's test.

RESULTS

In dry tubules, the accuracy of Root ZX was 75-91.7% for RL +/- 0.5 mm and 100% for RL +/- 1 mm, whilst the measurements of the other two EALs were all within the RL +/- 0.5 mm. No influence from the increase in tubule diameter on the accuracy of all three EALs was observed in dry tubules. In tubules filled with electrolyte, the accuracy of the Root ZX decreased as tubule diameter increased (R(d) > 0, P < 0.05). The RL-ML distance recorded by Propex was inversely related to the tubule diameter (R(d) < 0, P < 0.05). The accuracy of Propex was 75-100% for RL +/- 0.5 mm and 100% for RL +/- 0.5 mm when the tubule diameter was not more than 0.80 mm, but decreased in tubules with diameter over 0.80 mm and filled with 2.5% NaOCl or 17% EDTA. Nearly, all the measurements (except for six tubules) using Neosono Ultima EZ were within 1 mm shorter than RL despite the contents in tubules and the increase of tubule diameter.

CONCLUSIONS

The accuracy of the Root ZX decreased as the tubule diameter increased when tubules were filled with electrolytes. The electrolytes in the tubules decreased the accuracy of Propex when the tubule diameter was large. The electrolytes in tubules and tubule diameter had no influence on the accuracy of Neosono Ultima EZ. The Propex and Neosono Ultima EZ were more accurate than the Root ZX under various conditions in this laboratory study.

Ability of fourteen chemical agents used in dental practice to induce chromosome aberrations in Syrian hamster embryo cells

To assess the genotoxicity of 14 chemical agents used in dental practice, the ability of these agents to induce chromosome aberrations was examined using Syrian hamster embryo (SHE) cells. Statistically significant increases in the frequencies of chromosome aberrations were induced in SHE cells treated with 7 of 10 chemical agents used as endodontic medicaments, that is, carbol camphor, m-cresol, eugenol, guaiacol, zinc oxide, hydrogen peroxide, and formaldehyde. The other 3 chemical agents, that is, thymol, glutaraldehyde, and iodoform, did not increase the levels of chromosome aberrations. Of the 4 chemical agents that are used as an antiseptic on the oral mucosa, chromosome aberrations were induced by iodine, but not by the other 3 antiseptics, benzalkonium chloride, benzethonium chloride, and chlorhexidine. Among the 6 chemical agents exhibiting a negative response in the assay, only thymol induced chromosome aberrations in the presence of exogenous metabolic activation. Our results indicate that chemical agents having a positive response in the present study are potentially genotoxic to mammalian cells and need to be studied further in detail.

In vitro evaluation of the susceptibility of endodontic pathogens to calcium hydroxide combined with different vehicles

The aim of this study was to investigate in vitro the antimicrobial activity of calcium hydroxide [Ca(OH)2] in combination with different vehicles against endodontic pathogens. For such purpose, a broth dilution test was performed. Pastes were prepared with Ca(OH)2 powder and the following vehicles: sterile water, glycerin, camphorated monochlorophenol (CMCP), CMCP + glycerin, polyethyleneglycol and CMCP + polyethyleneglycol. The time required for the pastes to produce negative cultures against the tested microorganisms was recorded and analyzed statistically using the Kruskal Wallis test at 5% significance level. Timing for pastes to eliminate the aerobic and facultative anaerobic microorganisms ranged from 6 to 24 h, while strict anaerobic microorganisms were inhibited within 30 s to 5 min. Microbial susceptibility, ranked from weakest to strongest, can be presented as follows: Enterococcus faecalis (the most resistant microorganism), Candida albicans, Staphylococcus aureus, Porphyromonas gingivalis, Porphyromonas endodontalis and Prevotella intermedia (the last two microorganisms required the same time to be eliminated). In conclusion, calcium hydroxide pastes needed more time to eliminate facultative than anaereobic microorganisms. These findings suggest that the antimicrobial property is related both to paste formulation and to microbial susceptibility.

Assessment of a gel-type chelating preparation containing 1-hydroxyethylidene-1, 1-bisphosphonate

AIM

To test an aqueous gel containing 1-hydroxyethylidene-1, 1-bisphosphonate (HEBP) regarding its interactions with sodium hypochlorite, its calcium binding capacity, and its potential in preventing the formation of a smear layer when used in conjunction with rotary root canal preparation.

METHODOLOGY

The experimental aqueous gel consisted of (w/v) 2% alginate, 3% aerosil, 10% Tween 80 and 18% HEBP. Interactions of gel components with hypochlorite were assessed using iodometric titration and monochromatic ultraviolet spectrometry. Two commercial paste-type chelators containing ethylenediaminetetraacetic acid (EDTA) and peroxide (RC-Prep and Glyde) served as controls. Calcium-binding capacities were measured in mixtures with a Ca2+ standard solution buffered at pH 10 using a calcium-selective measuring chain. Finally, root canals of 16 extracted single-rooted premolars per group were instrumented using ProFile instruments dipped in the experimental gel, RC-Prep, or nothing. Additionally, canals were rinsed with 10 mL of a 1% NaOCl solution during/after preparation. Smear scores in instrumented teeth were monitored using scanning electron microscopy.

RESULTS

None of the experimental gel components showed short-term interactions with hypochlorite, whilst EDTA, peroxide, RC-Prep and Glyde immediately reduced the hypochlorite in solution. The experimental gel chelated 30 mg Ca2+ g-1, compared with 16 mg Ca2+ g-1 and 11 mg Ca2+ g-1 chelated by RC-Prep and Glyde respectively. Smear scores obtained with the experimental gel were significantly (P<0.05) lower than with RC-Prep in coronal and middle root thirds, whilst no differences were observed in apical root thirds.

CONCLUSIONS

Under the conditions of this study, an HEBP gel appeared advantageous over currently available products.

Calcium release and pH-characteristics of calcium hydroxide plus points

AIM

To evaluate calcium ion release and pH-characteristics of calcium hydroxide plus points (CHPP), conventional calcium hydroxide points (CHP, both Coltène/Whaledent, Langenau, Germany) and aqueous calcium hydroxide suspension (CHS) (Calxyl, OCO, Dirmstein, Germany).

METHODOLOGY

Ten CHPP or CHP of size 50 were immersed into 5 mL isotonic sodium chloride solution. Conventional Ca(OH)2-free gutta-percha points served as negative control. Calcium release was measured up to 44 days by means of complexometric titration. Time dependent pH behaviour of all points in comparison with CHS was determined immersing 30 points of size 50 into 2.3 mL 0.9% wt NaCl-solution at time intervals of 0.5-72 h by a microelectrode measuring chain and a pH-meter. The surface morphologies of new and used gutta-percha points were evaluated qualitatively under a scanning electron microscope. Statistical evaluation was carried out using Kolmogorov-Smirnov-tests, Mann-Whitney-tests and multifactorial anova.

RESULTS

For CHPP, a threefold greater calcium release was measured compared with CHP. Both types of points as well as CHS showed a maximum pH of approximately 12. Differences between groups were statistically significant for calcium release and pH (multifactorial anova; P < 0.001). Both types of points showed porous surfaces after usage, with a rougher surface for CHPP.

CONCLUSIONS

CHPP and CHP increased the pH of isotonic sodium chloride >11 within 3 min. CHPP had a greater release of Ca2+ compared with CHP.

Effects of sodium ascorbate on microtensile bond strength of total-etching adhesive system to NaOCl treated dentine

OBJECTIVE

The purpose of this study was to determine the microtensile bond strengths of total etching adhesive systems to pulpal chamber wall dentine after treated with various irrigants.

METHODS

Thirty extracted human third molars were cut horizontally to expose the pulp horn. The roof of the pulp chamber and pulp tissues were removed. The teeth were then divided into five groups of five specimens each to treat with various irrigants. Specimens in each group were treated as follows: group 1, with water for 10 min; group 2, with sodium hypochlorite for 10 min; group 3, with sodium hypochlorite for 10 min and water for 10 min; group 4, with sodium hypochlorite for 10 min and sodium ascorbate for 10 min; group 5, with sodium hypochlorite for 10 min, sodium ascorbate for 10 min and water 10 min. Treated specimens were dried, bonded with a total-etching adhesive system (single bond) and restored with a resin composite (Z250) then kept for 24 h before determination of the microtensile bond strengths.

RESULTS

Group 2 (20.96+/-9.23 MPa) demonstrated significantly lower bond strengths than group 1 (30.06+/-10.44 MPa). No significant differences in bond strengths were found between group 3 (23.08+/-6.94) and group 2. Group 4 (40.55+/-8.99) demonstrated higher bond strengths than group 2. However, there were no significant differences between group 5 (24.55+/-9.73 MPa) and group 2.

CONCLUSIONS

Sodium hypochlorite significantly reduced the bond strengths of the adhesive when a total-etching was applied. The application of sodium ascorbate on sodium hypochlorite treated dentine significantly improved the bond strengths.

Comparative study of the sealing ability of a polydimethylsiloxane-based root canal sealer

The purpose of this study was to compare the sealing ability of three root canal sealers, RSA (polydimethylsiloxane sealer), Endion (glass-ionomer sealer) and Topseal (epoxy resin sealer), with and without smear layer removal. Ninety extracted human teeth were selected and assigned to 6 groups (n=15), according to the following protocols: in 3 groups, the smear layer was left intact and the root canals were obturated with gutta-percha points and RSA, Endion and Topseal, respectively; in the other 3 groups, the smear layer was removed and the root canals were obturated in the same way as described above. Microleakage was measured at 7 days, 1 month and 2 months, using the fluid transport model. The results were expressed in µL/24 h. Data were analyzed statistically by Kruskall-Wallis and Mann-Whitney non-parametric tests. The results showed that the Topseal group without smear layer leaked significantly less (p<0.05) than the RSA group without smear layer, at all experimental periods. No statistically significant differences (p>0.05) were found among the other groups, at the established evaluation intervals. The findings of this study showed that the polydimethylsiloxane sealer (RSA) did not yield better sealing ability than the other sealers, either in the presence or in the absence of smear layer. Topseal had the least microleakage from the root canal sealers evaluated.

Microtensile bond strength of light- and self-cured adhesive systems to intraradicular dentin using a translucent fiber post

This study evaluated the bond strength of a light- and self-cured adhesive system to different intraradicular dentin areas (cervical, middle and apical thirds). Twenty single-rooted teeth were instrumented and their roots were prepared to receive a #2 translucent fiber post (Light Post). The root canals were irrigated with 0.5% sodium hypochlorite for one minute, rinsed with water and dried using paper tips. The teeth were divided into two groups (n=10): Single Bond [SB] (light-cured) and Scotchbond Multi-Purpose Plus [SBMP] (self-cured). To avoid polymerization of the materials through the root lateral walls, the teeth were placed in a silicone mold and the adhesives applied with a thin microbrush according to manufacturer's instructions. The resin cement, Rely X ARC, was inserted into the root canals using Lentulo burs. The post was then placed and the light-curing procedure was carried out for 40 seconds (+/-500 mW/cm2). The roots were kept in a 100% relative moisture environment for 24 hours and stored in distilled water for an additional 24 hours. Each root was perpendicularly sectioned into 1-mm thick sections, resulting in approximately four slices per region. Dumbbell-shaped slices were obtained by trimming the proximal surfaces of each slice using a diamond bur until it touched the post. The bonded area was calculated, slices were attached to a special device and submitted to microtensile testing at 1 mm/minute crosshead speed. Data were analyzed using ANOVA and Tukey's test. The mean bond strength values (MPa) were: SBMP: cervical=10.8a, middle=7.9b%, apical=7.1bc; SB: cervical=8.1b, middle=6.0c, apical=6.9b. Significant differences were found between adhesive systems only for the cervical third. The cervical region showed higher mean bond strength values than the middle and apical regions (p<0.0001).

The influence of sodium hypochlorite and root canal sealers on post retention in different dentin regions

This study evaluated the influence of 5.25% NaOCl irrigant and root canal sealers on post retention in different dentin regions. Seventy-two human incisors were decoronated at the cemento-enamel junction and randomly divided into six groups (n=12) according to irrigant and sealer technique: G1-Distilled water (DW) without sealer; G2-DW + AH Plus (Dentsply/Maillefer); G3-DW + Endofill (Dentsply/Maillefer); G4-5.251%NaOCl without sealer; G5-5.25% NaOCl + AH Plus; G6-5.25% NaOCl + Endofill. Specimens were stored in a humid environment for 30 days at 37 degrees C and were prepared with FRC Postec's drills for post insertion. The posts were cemented with Excite DSC/Variolink II (Ivoclar/Vivadent). The specimens were sectioned through their long axis into three dental slices approximately 2.5 mm each, representing the cervical (C), middle (M) and apical (A) thirds of the root preparation. After calculating the adhered area of the specimens, they were submitted to the push-out test in a universal testing machine. The data were submitted to an analysis of variance (ANOVA) at a 5% significance level and to the Tukey test (p<0.05). The mean values (MPa) obtained for cervical, middle and apical areas of the root preparation, respectively, were: G1=8.6; 12.5 and 14.3, G2=13.5; 15.4 and 16.9; G3=6.9; 10.0 and 12.1; G4=13.0; 14.9 and 15.4; G5=11.3; 13.5 and 18.0; and G6=11.0; 11.8 and 11.5. Based on the results, the eugenol-based sealer (Endofill) resulted in significantly lower mean retention strength values compared with the resin-based sealer (AH Plus). The apical region showed the greatest retention. The lowest resistance to dislodgment was found in the cervical region, mainly in the groups that used distilled water for irrigating the root canal.

Effect of endodontic irrigation on bonding of resin cement to radicular dentin

The influence of endodontic irrigation on shear bond strengths of resin cement to radicular dentin was investigated. Human radicular dentin blocks were divided into four groups and subjected to one of four endodontic irrigations: ethylenediaminetetraacetic acid (EDTA) group, 17% EDTA for 60 s; EDTA/sodium hypochlorite (NaOCl) group, 17% EDTA for 60 s followed by 10 ml of 5% NaOCl for 15 s; NaOCl group, 10 ml of 5% NaOCl for 15 s; and control group, no treatment. Morphological changes of dentin surface after endodontic irrigation were observed by scanning electron microscopy (SEM). A resin block was bonded to the radicular dentin after irrigation using resin cement with either wet-bonding (Uni-Etch/One-Step; Bisco) or self-etching (Tyrian SPE/One-Step Plus; Bisco) adhesives. Shear bond strengths were measured and the penetration of resin tags into dentinal tubules at resin-dentin interface was observed by SEM. With the wet-bonding system, the shear bond strengths for the EDTA/NaOCl group, in which dentinal tubules openings and uniform resin tag penetration into dentinal tubules were observed, were significantly higher than the EDTA and control groups. With the self-etching system, the shear bond strengths were significantly lower in the EDTA group compared with the NaOCl and control groups. The effects of endodontic irrigation on the bonding of resin cement to radicular dentin depended on the dentin bonding system used.

Effect of pH Modified EDTA Solution to the Properties of Dentin

The purpose of this study was to evaluate the influence of smear layer removal with 3% EDTA solution (pH of 9.0) on the dentin in terms of the permeability of root canal disinfectants into the dentin, wetting by endodontic sealer, and adhesive strength of the sealer. Three types of disinfectant (formalin cresol, phenol, and calcium hydroxide) and 4 types of endodontic sealers (included eugenol, non-eugenol, polycarboxylic acid, and resin) were used. The contact angle between endodontic sealer solution and dentin decreased in the 3% EDTA group but increased in the 15% EDTA. The adhesive strength of endodontic sealer to dentin increased in the EDTA groups for all types of sealers. The permeability of root canal disinfectants increased to similar degrees in the 3% and the 15% EDTA groups. In comparing these properties, we propose that the 3% EDTA is more useful for clinical applications.

Dentinal Tubule Disinfection Using Three Calcium Hydroxide Formulations

The objective of this study was to determine the antibacterial efficacy of three calcium hydroxide (CH) formulations using an in vitro model of Enterococcus faecalis dentinal tubule infection. CH mixed with water (CH), CH mixed with iodine-potassium iodide (CH+IKI), and CH mixed with iodoform and silicone oil (Metapex) were tested. Human cylindrical dentin specimens infected with E. faecalis were filled with disinfectants and incubated for 1 week. Dentin powder samples collected with ISO 018 burs showed a statistically significant reduction in E. faecalis for all three experimental groups in comparison with untreated control specimens. Statistically significant differences were also found between the three experimental groups. Metapex was the most effective dentinal tubule disinfectant, followed by CH+IKI and then CH. Similar results were observed at greater dentin tubule depths (ISO 021 burs) with the exception that intracanal treatment with CH resulted in significantly higher numbers of E. faecalis in comparison with untreated control specimens.

Susceptibility to localized corrosion of stainless steel and NiTi endodontic instruments in irrigating solutions

AIM

To evaluate the pitting and crevice corrosion characteristics of stainless steel (SS) and NiTi endodontic files in R-EDTA and NaOCl irrigating solutions.

METHODOLOGY

The corrosion behaviour of two H-files produced from different SS alloys (Mani, AISI 303 SS, Dentsply Maillefer, AISI 304 SS) and one file produced from NiTi alloy (Maillefer) was determined in R-EDTA and NaOCl irrigating solutions by the cyclic potentiodynamic polarization method. The cutting flutes of 12 files of each material were embedded in an epoxy resin, polished, exposed to the irrigating solutions and used as an electrode. An Ag/AgCl electrode was used as a reference, a platinum plate was used as a counter electrode and polarization curves were obtained for all files in R-EDTA and NaOCl irrigating solutions in 37 degrees C with a potential scan rate of 5 mV min(-1). Corrosion potential (Ecorr), Corrosion current density (Icorr) and Pitting potential (Epit) were calculated from each curve. The results were statistically analysed with two-way anova and Student-Newman-Keuls (SNK) multiple comparison test with materials and irrigating solutions serving as discriminating variables (a = 0.05).

RESULTS

Cyclic polarization curves presented negative hysteresis implying that pitting or crevice corrosion are not likely to occur for all the materials examined in both irrigating solutions. In NaOCl all materials showed significantly higher Ecorr (P = 0.011) as well as lower Icorr compared with R-EDTA reagent. Moreover, all materials demonstrated equal Epit in NaOCl, which was to be found significantly lower (P = 0.009) than the value of Epit in R-EDTA.

CONCLUSIONS

None of the tested materials is susceptible to pitting or crevice corrosion in R-EDTA and NaOCl solutions and from this standpoint are appropriate for the production of endodontic files.

Physical and chemical properties of chlorhexidine and calcium hydroxide-containing medications

This study was performed to evaluate the physicochemical properties (pH, contact angle, working time, radio-opacity, and viscosity) of chlorhexidine (CHX) and calcium hydroxide-containing medications in gel form in different concentrations. The pH value was assessed with a pH meter. The contact angle was measured with a goniometer. The radio-opacity and working time measurements were taken in accordance with the standards of the International Organization for Standardization. The viscosity was evaluated using a Brookfield RVDV viscometer. The results showed that CHX did not affect the pH, radio-opacity, and working time of the calcium hydroxide-containing medications (p < 0.05). However, adding CHX lowered the contact angle and increased the viscosity of calcium hydroxide significantly. This research showed that CHX in different concentrations and in combination with calcium hydroxide has satisfactory physicochemical properties to be used as an intracanal medication.

FT-Raman spectroscopy of calcium hydroxide medicament in root canals

AIM

To investigate chemical changes in calcium hydroxide introduced into human root canals as a medicament using Fourier transform-(FT) Raman spectroscopy.

METHODOLOGY

Ten necrotic maxillary anterior teeth were selected in 10 patients. The teeth were divided into five treatment groups, according to the survey time. Root canal instrumentation was performed with hand instruments until the master apical file was size 40. Calcium hydroxide paste, in a 1 : 1.25 mixture by weight of powder and distilled water, was introduced directly into the root canal with a lentulo-spiral filler and then condensed with a finger plugger. The access cavity was sealed with a temporary dressing. After 2 and 4 days, then 2, 4 and 6 weeks, the calcium hydroxide paste was sampled with a K-file and then analysed using FT-Raman spectroscopy. The excitation source was an Nd : YAG laser with an excitation wavelength of 1064 nm. All spectra were taken with a laser power of 200 mW, 275-1185 scans, and 4 cm(-1) resolution. The conversion of calcium hydroxide to calcium carbonate was calculated on the basis of the spectral data obtained from the mixtures of both compounds.

RESULTS

The calcium hydroxide paste in the apical region showed weak bands at 1088 and 284 cm(-1), in addition to bands associated with calcium hydroxide. The weak bands, assigned to calcium carbonate, became stronger with time. Calcium carbonate content increased rapidly in the first 2 days and then tended to increase slowly. Approximately 11% of the calcium hydroxide at the apical portion of the canal was converted to calcium carbonate after 6 weeks. However, little alteration of the paste was noticed in the samples from the middle portion of the canal.

CONCLUSIONS

Calcium hydroxide medicament in root canals became transformed into calcium carbonate in the apical region within 2 days. Although the transformation continued with time, approximately 90% of the calcium hydroxide remained unchanged after 6 weeks.

Microorganisms growth in endodontic citric-acid solutions with and without microbiological stabilizer

The purpose of this study was to determine if citric-acid solutions for endodontic use can become contaminated and if the addition of a microbiological stabilizer to the acid would modify this situation. Five types of microorganisms were inoculated in tubes containing 10% citric-acid solutions, pH 1.8 (group A1), and 10% solution, pH 1.8, combined with 0.1% sodium benzoate (group A2). The results demonstrated that solutions of group A1 were contaminated with Candida albicans in 100% of the tubes, Escherichia coli in 80%, and Enterococcus faecalis in 50%. When stabilizer was added (group A2), C. albicans grew in only 30% of tubes and all bacterial species were neutralized.

Diffusion of calcitonin through the wall of the root canal

The aim of this study was to evaluate the in vitro diffusion of synthetic salmon calcitonin (CT), used as an intracanal medication, to the external root surface, with or without the presence of intact root cementum. Fifty-four human central incisors were used in the experiment, and were divided into two groups of 21 (test groups) and two groups of 6 teeth (control groups). After root canal preparation, 10 ml of calcitonin was inserted within the root canal chamber. The root was sealed and made externally impermeable. Specimens were then placed in tubes with saline solution buffered with phosphates and stored at 37°C. The diffusion of calcitonin was measured after 1, 4 and 7 days. To count calcitonin present at the external media (PBS), ELISA test (an antigen-antibody reaction) was used. Results showed that there was calcitonin diffusion through dentin in all of the test samples. The absence of cementum increased the diffusion of calcitonin (p=0.05). The highest counts of CT were obtained on day 7 for groups with or without cementum - showing a direct relation between time and diffusion of the medication.

Evaluation of pH levels and calcium ion release in various calcium hydroxide endodontic dressings

OBJECTIVE

The purpose of this study was to evaluate Ca(2+) release and pH of 3 calcium hydroxide-based products used routinely as intracanal dressings, as well as the new gutta-percha points with calcium hydroxide.

STUDY DESIGN

The pH and Ca(2+) release were assessed using Calen with camphorated paramonochlorophenol, saline calcium hydroxide paste, LC paste (Lopes and Costa paste-calcium hydroxide with olive oil), and calcium hydroxide containing gutta-percha points. The materials were inserted in polyethylene tubes and immersed in deionized water. The pH variation and Ca(2+) release were monitored periodically for 4 weeks.

RESULTS

After 72 hours, materials 1 and 2 raise the pH from 9.6 and 8.2 to 11.4 and 11.3, respectively, while a small change was observed for materials 3 and 4. The calcium concentration released from materials 1, 2, 3, and 4 after 72 hours was 6.54, 4.98, 1.31, and 1.74 mg/dL, respectively.

CONCLUSION

Calen plus camphorated paramonochlorophenol and saline calcium hydroxide paste exhibited the highest calcium release and pH levels.