Preoperative Simulation and Three-Dimensional Model for the Operative Treatment of Tibiofibular Diaphyseal Fracture: A Randomized Controlled Clinical Trial

BACKGROUND

In order to ascertain the safety and therapeutic efficacy of preoperative simulation in conjunction with three-dimensional (3D) printing modalities for the surgical management of tibiofibular diaphyseal fractures. We postulate that preoperative simulation and three-dimensional (3D) printing techniques have a significant impact on reducing the mean operative time, diminishing intraoperative blood loss, and decreasing the frequency of fluoroscopic.

MATERIAL AND METHODS

Sixty patients with tibiofibular diaphyseal fracture were divided into the conventional surgery group (n = 30) and the 3D printing group (n = 30). In the 3D printing group, preoperative equal-ratio fracture models prepared using the 3D printing technique were used to perform preoperative simulation, guide the real surgical operation, examine implant reduction and placement as well as preoperative plate/screw size. The operation time, intraoperative bleeding, frequency of fluoroscopies, Visual Analog Scale (VAS), and Johner-Wruhs Scale were recorded.

RESULTS

The operation time, blood loss, and the frequency of fluoroscopy during operation in the group with preoperative simulation and 3D printing were less than that in the conventional surgery group (p < 0.001). Meanwhile, the Visual Analog Scale (VAS) and Johner-Wruhs Scale were also improved in both groups.

CONCLUSION

The findings indicated that preoperative simulation and three-dimensional (3D) printing may facilitate the treatment of tibiofibular diaphyseal fractures, potentially enhancing preoperative planning and contributing to the precision and personalization of the surgical procedure. Thus, the application of this technology possesses considerable promise for future utilization in clinical practice.

TRIAL REGISTRY

Name of the registry: This study was registered in the Chinese Clinical Trial Registry; Trial registration number: ChiCTR2100052379.

Severe heterotopic ossification after total hip arthroplasty in male patients under 70 years of age: effectiveness of prophylactic protocol

BACKGROUND

This study aims to evaluate the incidence of clinically significant heterotopic ossification (HO) in primary total hip arthroplasty (THA), comparing outcomes with and without the adoption of an HO prophylactic protocol in male patients under 70 years of age.

METHODS

The prophylactic protocol involved the administration of 50 mg of Indomethacin twice daily for 3 weeks. HO presence was classified according to the Brooker classification system, considering "severe" clinically significant HO (Brooker grade 3 and 4).

RESULTS

Two hundred and seventy-nine patients were included in our study, and an overall HO rate of 68.2% versus a rate of 61.5% was found respectively in patients not subjected and subjected to prophylactic protocol, without significant difference (PR 0.062). However, patients not subjected to the HO prophylactic protocol exhibited a severe HO rate of 22.4% compared to 7.7% in the prophylactic group, with a statistically significant difference (P = 0.008).

CONCLUSIONS

Our study demonstrated that prophylactic protocol adoption is significantly associated with lower rate of severe HO in male patients under 70 years of age. Currently, there are no orthopedic guidelines for the prevention and management of HO after THA, but in the absence of contraindications, the adoption of a prophylactic protocol for HO should always be considered in high-risk patients.

The Burch-Schneider Reinforcement Ring : 200 cases over a 40-year period with a mean follow-up of 11 years

Aims

The Burch-Schneider Reinforcement Ring (BSRR) was developed to manage significant acetabular defects and prevent protrusion in complex primary and revision total hip arthroplasties. This study evaluates the long-term performance of the BSRR over four decades, focusing on survival, patient-reported outcomes, radiological evidence of loosening, complication rates, and factors associated with implant failure.

Methods

We conducted a retrospective analysis of 200 hips treated with the BSRR at the Cantonal Hospital of Fribourg, Fribourg, Switzerland, from January 1974 to December 2018. Clinical and radiological data were reviewed, and patients were followed through clinical visits, questionnaires, and registry data. Outcomes were assessed using standardized scoring systems and radiological evaluations. Kaplan-Meier survival analysis and Cox proportional hazards modelling were used to identify factors associated with implant failure.

Results

The cumulative survival of the BSRR was 72% (95% CI 50 to 100) at 20 years with any clinical or radiological failure as the endpoint, and 97% (95% CI 95 to 100) at 20 years for revision of the BSRR specifically. Clinical outcomes showed moderate improvements at final-follow-up, with a mean Harris Hip Score of 53.4 (SD 25.3) and a Hip disability and Osteoarthritis Outcome Score of 72.8 (SD 18.6). Radiologically at final follow-up, the BSRR demonstrated good stability, with 1.5% of cases (n = 2) showing probable loosening and low rates of osteolysis (3% acetabular (n = 4) and 14% femoral (n = 18)). The primary predictor of implant failure was the Paprosky Grade IV acetabular defect, with a hazard ratio of 4.4 (95% CI 1.2 to 15.7).

Conclusion

The BSRR remains an effective solution for acetabular revision surgery, providing consistent long-term outcomes. Its durability makes it a valuable tool in orthopaedic surgery, especially when managing significant bone loss.

Rim-point-column-oriented algorithm in cementless acetabular reconstruction in revision total hip arthroplasty : a minimum five-year follow-up study

Aims

The Paprosky acetabular defect classification and associated algorithms cannot adequately guide cementless acetabular reconstruction when using porous metal augments. We aimed to introduce a rim, points, and column (RPC)-orientated cementless acetabular reconstruction algorithm, and hypothesized that patients undergoing this treatment would demonstrate satisfactory mid-term clinical and radiological outcomes.

Methods

We enrolled 114 patients (119 hips) who underwent revision total hip arthroplasty between April 2014 and November 2017 by a single surgeon. A minimum five-year radiological follow-up was available for 90 hips (75.6%), with mean clinical and radiological follow-up durations of 6.8 years (SD 0.9) and 6.3 years (SD 1.9), respectively.

Results

Harris Hip Scores improved from 35.4 (SD 10.2) preoperatively to 86.0 (SD 10.3) postoperatively (p < 0.001). Fixation modes included rim fixation (33 hips; 27.7%), three-point fixation without point reconstruction (42 hips; 35.3%), three-point fixation with point reconstruction (40 hips; 33.6%), and three-point fixation with pelvic distraction (four hips; 3.4%). Medial wall reconstruction was performed in 20 patients (16.8%). All acetabular components were radiologically stable. Nine-year Kaplan-Meier survival rates for periprosthetic joint infection, any reoperation, and dissatisfaction were 98.28% (95% CI 88.38 to 99.76), 94.37% (95% CI 81.93 to 98.33), and 95.10% (95% CI 84.64 to 98.50), respectively.

Conclusion

Acetabular component stability in cementless acetabular reconstruction relies on rim or three-point fixation, with anterior and posterior column continuity providing essential stability. Medial wall reconstruction complements fixation in the RPC algorithm, yielding satisfactory mid-term outcomes.

Condylar-Stabilized Designs in Total Knee Arthroplasty: A Classification System and Review of Outcomes

BACKGROUND

The increasing use of condylar-stabilized (CS) bearing designs in primary total knee arthroplasty (TKA) can be attributed to bony preservation with the option for posterior cruciate ligament (PCL) resection without compromising kinematics. Although there are a variety of CS designs, there is no system of nomenclature for them, making comparisons challenging. This study proposes a comprehensive classification system of differing CS designs based on articular surface and femoral component geometries and kinematic principles. We also review the literature for functional outcomes and survivorship associated with each CS design.

MATERIALS AND METHODS

There were 31 CS designs noted from 21 manufacturers identified using a combination of literature reviews, web searches, surgeon input, and manufacturer correspondence. The designs were subsequently categorized into distinct groups based on their geometry, the location of polyethylene buildup, conformity compared to their CR counterparts, and the radius of the femoral component. A scoping review was conducted to evaluate patient-reported outcome measures (PROMs), ranges of motion (ROM), and survivorships associated with each category. After exclusion, we reviewed 91 studies in the PubMed, Ovid MEDLINE, Embase, Cochrane, Web of Science, and Scopus databases.

RESULTS

We established five distinct categories: 1) anterior-stabilized; 2) ultracongruent; 3) medial-stabilized; 4) medial-pivot; and 5) lateral-stabilized. There were 12 studies describing anterior-stabilized designs, 15 describing ultracongruent, two describing medial-stabilized, 55 describing medial-pivot, and three describing lateral-stabilized designs. All CS designs demonstrated significant improvements in PROMs and ROM postoperatively, with survivorship of at least 90% and follow-up ranging from two to 18 years in some designs.

CONCLUSIONS

The classification developed in this study will allow for appropriate grouping and comparison of distinct condylar-stabilized implants. As presented in this review, there are favorable short-term functional outcomes across all CS subcategories. Although the data associated with these designs appears promising, it is limited. Further research comparing different designs to understand how differing geometries impact kinematic function and clinical outcomes may potentially inform implant selection and future design.

Medial Congruent and Medial Pivot Inserts in Total Knee Arthroplasty: A Scoping Review

Background and Objectives: Total knee arthroplasty (TKA) is one of the most common medical procedures worldwide. However, 10 to 20% of patients are still dissatisfied despite implants and surgical technique advancements. Recently, several medial-stabilized TKAs have been developed in attempts to replicate the native kinematics of the knee. The aim of this scoping review on medial-stabilized TKA inserts-medial congruent (MC) and medial pivot (MP)-is to focus on their clinical outcomes and the role of the posterior cruciate ligament (PCL), aiming to systematically map the existing research and highlight current knowledge gaps. Materials and Methods: A search of the PubMed, Embase and Cochrane databases was performed to identify relevant studies on the kinematics and outcomes of medial pivot (MP) or medial congruent (MC) inserts. The following Mesh terms were used in combination with the Boolean operators "AND" and "OR": "total knee arthroplasty", "total knee replacement", "medial pivot", "medial congruence", "outcomes" and "kinematic". Original studies reporting on clinical outcomes assessed with validated patient-reported scales, surgical techniques and reoperation rates for any reason with a minimum follow-up of 18 months were included. Results: A total of 39 articles met the inclusion criteria, accounting for 6143 total knee replacements. The overall reoperation-free survivorship rate was 98.4% (6047 out of 6143 knees) at a weighted average follow-up of 6.3 years (range 1.5-15.2 years, SD 0.7). Both MP and MC inserts demonstrated good outcomes, with no differences between groups. Few studies evaluated the role of the PCL in MP and MC inserts, with no differences in terms of clinical outcomes between retaining and sacrificing the PCL. Conclusions: MS-TKA demonstrated good outcomes in the literature independently of the specific design (medial pivot or medial congruent). Different possible biases may be present when evaluating the outcomes of these inserts, including different types of alignment and soft tissue balancing philosophies.

Safety, Efficacy, and Adjacent-level Fracture Risk Following Vertebral Augmentation and Radiofrequency Ablation for the Treatment of Spine Metastases in Patients with Cancer

Purpose To evaluate the safety and efficacy of vertebral augmentation (VA) and radiofrequency ablation (RFA) for treating pathologic spinal fractures in patients with cancer and adjacent fracture risk following treatment. Materials and Methods This single-institution retrospective study, conducted from January 2017 to September 2020, included patients with cancer who underwent percutaneous VA with or without spine RFA for pathologic spine compression fractures. The primary outcome was pain reduction, assessed using the 10-point visual analog scale before the procedure, at first follow-up, and 2-4 weeks after the procedure. Logistic regression was performed to identify factors associated with epidural cement leak. Results A total of 638 spinal levels in 335 patients (median age, 65 years [IQR, 58-74 years]; 147 female, 188 male) were treated. Epidural tumor and retropulsion of bone fragments were present in 15% (93 of 638) and 13% (81 of 638) of treated levels, respectively, while posterior wall erosion was observed in 30% (190 of 638). Substantial pain improvement (greater than two-point reduction) occurred in 81% (519 of 638) of cases. Factors associated with decreased risk of epidural cement leak included RFA (42% no leak vs 38% leak, P = .03) and lumbar treatments (49% no leak vs 38% leak, P = .02). Adjacent-level fractures occurred in 10.4% of patients. The total complication rate (National Cancer Institute Common Terminology Criteria for Adverse Events grade 3 or higher) was 0.6% (four of 638). Conclusion VA and RFA are safe and efficacious treatments for spine fractures in patients with cancer. Keywords: Ablation Techniques, Kyphoplasty, Vertebroplasty © RSNA, 2025.

Hip resurfacing arthroplasty reduces dislocation and infection rates without differences in clinical outcomes compared to short and standard stems: A Network Meta-Analysis

BACKGROUND

Total hip arthroplasty (THA) and hip resurfacing arthroplasty (HRA) are established treatments for hip osteoarthritis. Recent advancements have introduced short-stem THA, which offers potential advantages in terms of bone preservation and biomechanical restauration. None of previous studies compared these three surgical interventions. The aim of this network meta-analysis (NMA) is to compare HRA, short stem and standard stem in THA in terms of: (1) complications rate (global, infection and dislocation rate), (2) clinical outcomes (WOMAC, Harris Hip Score (HHS), Oxford Hip Score (OHS), Forgotten Joint Score (FJS), Postel Merle Aubigné Score (PMA) and SF-36) at short- and mid-term, (3) procedure-related variables (operative time, pain at day one and length of stay).

METHODS

A systematic literature review was conducted using multiple electronic databases (Medline, Central and Embase) to identify comparative studies evaluating at least two of the three surgical interventions. Studies were included if they reported one of our outcomes. Data synthesis was performed using a Bayesian NMA. A total of 72 studies including, 793 593 patients (mean age 54.7 years), met the inclusion criteria. The most common comparison was standard-stem THA/ HRA (94,4% of the studies).

RESULTS

The NMA did not identify differences for the rate of global complications between short stem THA/standard-stem THA (risk ratio (RR) 1.52 [95% CI 0.41-5.96]), HRA/standard-stem THA (RR 1.17 [95% CI 0.85-1.66]) and HRA/short-stem THA (RR 0.77 [95% CI 0.20-2.95]). Regarding infection and dislocation, standard THA had a higher rate of infection (risk ratio 2.14 [95% CI 1.33-5.44]) and of dislocation (risk ratio 13.45 [95% CI 3.37-98.21]) compared to HRA. For functional outcomes at short term, no differences were observed between HRA and standard-stem THA for WOMAC (Mean Difference (MD) -0.01 [95% CI -0.51 to 0.40]), HHS (MD 0.05 [95% CI -3.26 to 3.45]), PMA (MD -0.13 [95% CI -0.94 to 0.71]) and FJS (MD -1.64 [95% CI -9.04-5.45]). For functional outcomes at mid-term, no differences were observed between HRA and standard-stem THA for WOMAC (MD -0.07 [95% CI -1.13 to 1.05]), HHS (MD -0.02 [95% CI -1.55 to 1.36]), PMA (MD -0.03 [95% CI -0.60 to 0.49]) and SF-36 (MD 0.11 [95% CI -3.37 to 3.61]). No difference was observed for comparison of short-stem THA/standard-stem THA and HRA/short-stem THA for clinical outcomes.The surgical time was shorter for HRA compared to short-stem THA (MD-34.05 [95% CI -53.25 to -13.28]) and standard-stem THA (MD -16.25 [95% CI -24.84 to -7.53]). No difference was observed between HRA and standard-stem THA for VAS at day one (MD 0.22 [95% CI -1.90 to 2.13]) and for the length of stay (MD 0.48 [95% CI -0.27 to 1.34]).

CONCLUSION

HRA demonstrated had lower infection and dislocation rate compared to standard THA. HRA also offers a shorter operative time. However, no difference was observed for functional outcome between the three technics. These findings support the notion that the choice of technique should be tailored to patient-specific characteristics, highlighting the potential shift towards personalized hip arthroplasty.

LEVEL OF EVIDENCE

III; Network meta-analysis.

Use of structural bone allograft in revision hip arthroplasty for massive acetabular defect: A systematic review and meta-analysis

Purpose

Managing substantial acetabular defects during revision total hip arthroplasty (rTHA) poses significant challenges, with a range of techniques available and ongoing discussions regarding their efficacy. This meta-analysis aimed to assess the failure rates associated with Paprosky type III and American Academy of Orthopaedic Surgeons (AAOS) types III-IV acetabular defects treated with structural allografts in conjunction with cemented cups, cementless cups, or reinforcement devices.

Methods

A systematic review was performed utilising PubMed/MEDLINE, EMBASE, and the Cochrane Database of Systematic Reviews to identify pertinent studies published from January 1980 to 1 April 2024. The search employed terms related to acetabular impaction bone grafting, rTHA, and associated techniques. The main outcome measure was the implant failure rate over an 8-year period.

Results

Twenty-eight studies met the established inclusion criteria, covering three therapeutic approaches: (1) structural allograft with a cemented cup (four studies), (2) structural allograft with a cementless cup (10 studies), and (3) structural allograft with reinforcement devices (21 studies). The overall 8-year implant failure rate was found to be 16% (95% CI, 11%-21%), with significant differences noted among the treatment modalities (p = 0.017). The failure rate was lowest for reinforcement devices (12%) and highest for cemented cups (30%). The predominant failure mechanism was aseptic loosening (68.9%), followed by infection (20.3%) and dislocation (10.8%). Rates of aseptic loosening were greater with cemented cups compared to cementless cups and reinforcement devices (19% vs. 13% and 6%, respectively; p = 0.023).

Conclusions

Structural allografts combined with reinforcement devices yield favourable outcomes for managing large acetabular defects during revision THA, demonstrating significantly lower failure rates compared to other techniques. The addition of reinforcement devices substantially reduces the risk of implant failure.

Level of Evidence

Level III.

A Modified Wagner Stem Design Increases the Primary Stability in Cementless Revision Hip Arthroplasty

Background

Primary stability is of great importance for the longevity of the implant in cementless revision total hip arthroplasty, since instability is a major cause of rerevision. The purpose of this study was to evaluate the effect of an additional set of less prominent, wider splines added to an established conical stem design with sharp splines on axial stability in a model with significant proximal bone defects.

Methods

Twenty fresh-frozen human femurs were implanted with either the established or the additional spline design, dynamically loaded and tested in a load-to-failure configuration. Cortical contact in the femoral canal after implantation was evaluated by superimposing computed tomography scans and 3-dimensional laser scans. Stem subsidence and micromotion were evaluated to assess primary stability.

Results

Stems remained stable during cyclic loading of up to 200% body weight, except in bones with cortical bone mineral density below 1000 mgHA/mL. A significant reduction of more than 85% in stem subsidence (P = .040), axial micromotion (P = .007), and rotational micromotion (P = .010) was achieved with the new spline design. Load-to-failure testing exceeded 400% body weight.

Conclusions

The new spline design increased the cortical contact which resulted in increased axial primary stability in this in vitro experiment. Bone mineral density as a measure of bone quality proved to be a decisive factor for achieving immediate postoperative stability. Further variations of the established stem designs could further improve the longevity of artificial joint replacements.

Fourth-generation Ceramic Head Fracture in Total Hip Arthroplasty: A Case Report and Literature Review

Ceramics are used in total hip arthroplasty due to inherent wettability and low wear rates, but fracture risk is a known complication. Rates as high as 13.4% were reported in the past, yet as low as 0.02% in newer generations. Howard et al. reported a fracture rate of 0.009% for fourth-generation ceramic heads. We present a case report of a 69-year-old male with a BMI of 40.01 kg/m2 who suffered a fracture of a 36-mm ceramic femoral head with pseudoacetabular involvement of the polyethylene liner. This occurred 2 years and 3 months after his primary surgery after a 4-foot fall off of a ladder. The patient underwent revision of his total hip arthroplasty with arthroplasty of the polyethylene liner and femoral head component without stem explantation.

The use of three-dimensional printing and virtual reality technologies in orthopaedics-with a focus on orthopaedic trauma

Although the use of three-dimensional printing in orthopaedics is relatively new, many benefits of this technology to both patients and providers have already been observed. Printing models of fractured bone based upon segmented CT imaging allows for improved surgical planning as surgeons are able to view and physically manipulate accurate representations of fracture patterns prior to surgery, increasing both speed and accuracy of fixation in the operating room. The use of three-dimensional models by surgeons prior to surgery has been shown to reduce blood loss, intraoperative time, and fluoroscopy use. These models also have incredible potential in orthopaedic resident and patient education. Among residents, these models significantly improve recognition of fracture patterns, while patients benefit from the use of these models through increased trust and satisfaction with their surgeon's care, as well as decreased anxiety about their injury. Currently, the imaging segmentation and model generation process are prohibitively costly both in terms of time and money; however, in the future, three-dimensional printing may become a point-of-care technology in the orthopaedic field as technology improves and costs decrease. This article aims to illustrate the value of three-dimensional printing and virtual reality technologies in preoperative planning and intraoperative precision, resident education, and patient understanding and satisfaction. The benefits and challenges of the technologies are discussed, as well as current limitations.

Management of Elderly Elbow Fractures

Background

Elbow fractures are common in elderly patients with osteoporotic bones, typically resulting from falls on the elbow. Common fracture types include distal humerus, olecranon, and radial head fractures. Occasionally, a combination of these fractures occurs, creating complex injuries such as terrible triad injuries. Accurate evaluation using X-rays and CT scans is essential for optimal treatment planning. Careful preoperative planning, including the decision between non-operative and operative treatment and selecting appropriate surgical implants, is critical for achieving successful outcomes.

Objective

This chapter focuses on common elbow fractures in elderly patients and explores the available treatment options. Given the lack of clear consensus on managing elbow fractures in osteoporotic bones, we address the associated complications and highlight various treatment approaches.

Current Knowledge

Numerous treatment methods have been proposed for osteoporotic elbow fractures, including various fixation techniques, arthroplasty, and excisions. Despite the availability of multiple treatment options, no method has emerged as superior. Each method has distinct advantages and disadvantages. This chapter aims to compile and compare these options, outlining their respective pros and cons.

Conclusions

Elbow fractures in osteoporotic bones present significant challenges for surgeons. Although elderly patients with osteoporotic bones generally have lower functional demands compared to younger individuals, they still require adequate, pain-free elbow function for daily activities. Advances in surgical techniques and implant technology have expanded treatment options for these fractures. Achieving successful outcomes requires selecting the appropriate implant, meticulous preoperative planning, and expert surgical execution tailored to the specific fracture characteristics.

Can a 1.5-Stage Revision Be an Effective Alternative for Chronic Periprosthetic Hip and Knee Infections? A Systematic Review and Meta-Analysis

BACKGROUND

A 1.5-stage revision could be an alternative to a 2-stage revision for treating hip and knee chronic periprosthetic infections, guaranteeing the maintenance of joint function and infection control and preventing infection-free patients from undergoing further surgery. Our systematic review aimed to answer several questions about the indication, the infection eradication rate, and the long-term functional outcome of 1.5-stage revisions used to treat chronic periprosthetic infections of the hip and knee.

METHODS

A systematic review of the literature was performed following the Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines, including studies dealing with the use of 1.5-stage and two-stage surgery for chronic periprosthetic joint infection following total knee arthroplasty or total hip arthroplasty The Coleman Methodology Score and the Methodological Index for Nonrandomized Studies score were used to assess the quality of the studies. A meta-analysis was performed to evaluate the infection eradication rate using either the 1.5-stage revision or the 2-stage technique. A total of 494 patients (111 hips and 385 knees) who underwent 1.5-stage with a mean age of 69 years (range, 61 to 82) were identified in the ten included studies.

RESULTS

The most common cause of reoperation was the conversion to the definitive prosthesis, followed by aseptic loosening. Infection control was reached in 84.6% of the 1.5-stage and 76.1% of the two-stage cohorts. The infection recurrence rate was higher in the two-stage cohort than the 1.5-stage group (21.8 versus 14.3%).

CONCLUSIONS

The 1.5-stage technique represents a valid treatment option in selected patients who have chronic periprosthetic joint infection who cannot undergo further surgeries, adding together the benefits of the 1- and 2-stage procedures. Furthermore, the 1.5-stage showed a better success rate in the infection resolution than the 2-stage technique.

Tranexamic Acid Led to Improved Safety of Total Knee Arthroplasty in Jehovah's Witness Patients: A Multicentered Matched Study

BACKGROUND

This study aimed to evaluate the safety of total knee arthroplasty (TKA) in Jehovah's Witness patients compared to non-Jehovah's Witness patients using standard perioperative TKA protocols and assess the role of tranexamic acid (TXA) in managing blood loss in this population.

METHODS

Patients undergoing TKA between 2011 and 2021 at 2 tertiary academic centers were retrospectively reviewed. Patient demographics, preoperative and postoperative hematologic laboratory values, intraoperative TXA use, 90-day postoperative complications, and subsequent revisions were collected. These variables were then compared between propensity score-matched cohorts at a 2:1 ratio of those who did not identify as Jehovah's Witness to those who did. Regression analysis was used to determine the effect of intraoperative TXA on hemoglobin (hgb) shift.

RESULTS

After applying exclusion criteria and matching, the TKA outcomes of 316 non-Jehovah's Witness patients and 152 Jehovah's Witness patients were analyzed. Univariate analysis suggested that non-Jehovah's Witness patients and Jehovah's Witness patients had similar preoperative and postoperative hgb, hgb shift, and hematocrit. Only 1 (0.8%) Jehovah's Witness patient reached an hgb < 8.0 mg/dL postoperatively. Multivariate logistic regression suggested that Jehovah's Witness patients did not have increased odds of reaching an hgb < 8.0 mg/dL (odds ratio = 0.99 [0.96, 1.02]; P = 0.42). Multivariate linear regression suggested that intraoperative TXA was positively correlated with hgb shift and thus a smaller decrease in hgb from pre-TKA to post-TKA (β = 0.38 [0.06, 0.69]; P = 0.02). Additionally, Jehovah's Witness patients had excellent revision-free (95% [91, 99]) and infection-free (98% [95, 100]) survival at 8 years.

CONCLUSIONS

Standard perioperative TKA protocols are safe for Jehovah's Witness patients who do not have the need for transfusion, especially with appropriate preoperative hgb levels and the use of intraoperative TXA. Furthermore, these patients have excellent survivorship at 5 and 8 years of follow-up.

LEVEL OF EVIDENCE

Level III.

Integrating finite element analysis in total hip arthroplasty for childhood hip disorders: Enhancing precision and outcomes

Total hip arthroplasty for adults with sequelae from childhood hip disorders poses significant challenges due to altered anatomy. The paper published by Oommen et al reviews the essential management strategies for these complex cases. This article explores the integration of finite element analysis (FEA) to enhance surgical precision and outcomes. FEA provides detailed biomechanical insights, aiding in preoperative planning, implant design, and surgical technique optimization. By simulating implant configurations and assessing bone quality, FEA helps in customizing implants and evaluating surgical techniques like subtrochanteric shortening osteotomy. Advanced imaging techniques, such as 3D printing, virtual reality, and augmented reality, further enhance total hip arthroplasty precision. Future research should focus on validating FEA models, developing patient-specific simulations, and promoting multidisciplinary collaboration. Integrating FEA and advanced technologies in total hip arthroplasty can improve functional outcomes, reduce complications, and enhance quality of life for patients with childhood hip disorder sequelae.

Life-threatening postoperative hemorrhage caused by lumbar artery injury in asymmetrical pedicle subtraction osteotomy for severe spinal deformity: two case reports

PURPOSE

To present two cases of life-threatening hemorrhage related to lumbar artery injury in adult spinal deformity (ASD) patients following S2‑alar‑iliac (S2AI) fixation and asymmetrical pedicle subtraction osteotomy (PSO), and discuss the possible reasons for postoperative hemorrhage in these patients.

METHODS

Patient A was a 52-year-old female with degenerative lumbar scoliosis who underwent posterior spinal fusion from T8-S2 and one-level PSO at L2. Patient B was a 24-year-old male with severe kyphoscoliosis due to non-ambulatory cerebral palsy, who underwent posterior spinal fusion from T3-S2 and one-level PSO at L1. Both patients underwent asymmetric PSO, where a larger wedge was resected from the convex side of the vertebral body rather than the concave side.

RESULTS

Both patients occurred a sudden increase in drainage within 3 h postoperatively, who were under anesthesia in AICU. Digital subtraction angiography (DSA) was emergently performed and revealed that the bleeding sites were from the lumbar artery, which was adherent to the convex side of the osteotomized vertebra in both cases. Then successful bleeding control was achieved through vascular embolization. Postoperative CT revealed spike formation at the anterior edges of the open wedge at the PSO level due to sagittal translation (ST), with noticeable derotation of the osteotomized vertebra.

CONCLUSION

For patients with severe kyphoscoliosis, asymmetrical PSO increases the risk of lumbar artery injury on the convex side, and postoperative ST may further contribute to this risk. In cases where a sudden increase in drainage is observed postoperatively, it is crucial to consider the possibility of lumbar artery injury, particularly on the convex side of the osteotomized vertebra.

Long-term results of revision total hip arthroplasties using cementless stems and allografts for paprosky type IIIB and IV femoral defects short title: Revision hip arthroplasty in type IIIB and IV femoral defects

PURPOSE

We determined long-term (1) clinical results of revision total hip arthroplasty (THA) in the presence of Paprosky type IIIB and IV femoral defects using validated scoring instrument; (2) osseointegration and bone remodeling; (3) the fate of cortical strut onlay allograft; (4) rates of revision and osteolysis; and (5) survivorship of the cementless stem.

METHODS

We reviewed the results of 240 revision THAs in 220 patients (mean age, 59 years, range, 36-67 years) performed with an extensively porous-coated femoral stem (Solution stem; DePuy, Warsaw, Indiana) combined with a cortical strut onlay allografts for Paprosky Type IIIB and IV femoral diaphyseal bone defects from February 1994 to June 2003. Demographic data, Harris hip score, WOMAC score, UCLA activity score, and radiographic data were recorded. We determined the fate of strut cortical strut allograft and component survival rates at a mean of 26.5 years using revision and aseptic loosening as end points. Minimum follow-up was 21 years (range, 21-30 years).

RESULTS

The clinical results improved significantly for the Harris hip score, WOMAC, and UCLA activity scores (p < 0.001). At the final follow-up, mean Harris hip, WOMAC, and UCLA activity scores were 83 ± 15 (34-100), 20 ± 15 (11-52) and 6.7 ± 1.3 (5-8) points, respectively. Of the 240 femoral stems, 218 (91%) had bone ingrowth, and 22 (9%) were unstable. Allografts were well incorporated in the host femur in all hips. The resorption of allografts was graded as mild in 192 hips (80%) and moderate in 48 hips (20%). A Kaplan-Meier survivorship analysis at a mean of 26.5 years follow-up showed that the survival rate of the femoral component was 91% (95% CI, 0.88-0.96) with re-revision for any reason as the endpoint for failure. The survival rate at a mean of 26.5 years for worst case scenario was 76% (95% CI, 0.71-0.88).

CONCLUSION

We found good results at a mean of 26.5 years after the revision surgery in terms of longevity and functional outcome using an extensively porous-coated stem combined with cortical strut allografts in the Paprosky Type IIIB and IV femoral diaphyseal defects. We agree that the initial quality of an uncomplicated revision of THA using supportive cortical strut allografts maintains relatively well beyond minimum 21 years of follow-up. Future studies might compare this approach with allograft-prosthesis composites, proximal femoral replacement, or modular fluted tapered stems.

What Are the Functional, Radiographic, and Survivorship Outcomes of a Modified Cup-cage Technique for Pelvic Discontinuity?

BACKGROUND

Pelvic discontinuity (PD) presents a complex challenge in revision hip arthroplasty. The traditional cup-cage construct, which involves a screw-secured porous metal cup and an overlying antiprotrusio cage, has shown promising mid- to long-term results. However, there is limited information on the outcomes of modifications to the original technique. Our study aims to evaluate a modified technique in which the cup position is determined by the placement of the overlying cage, allowing for adjustments to achieve optimal orientation.

QUESTIONS/PURPOSES

Among patients treated for PD with a cup-cage construct in which the cup position was dictated by the position of the cage: (1) What are Harris hip scores achieved at a minimum of 2 years of follow-up? (2) What is the Kaplan-Meier survivorship free from aseptic loosening or component migration? (3) What is the Kaplan-Meier survivorship free from revision for any reason? (4) What surgical complications are associated with the procedure?

METHODS

Between October 2013 and January 2022, we performed 805 acetabular revisions. Among these, 33 patients with PD confirmed intraoperatively were considered potentially eligible for a cup-cage construct; no other method of surgical management was used. We performed 64% (21 of 33) of these procedures from October 2013 to January 2018, with 6% (2 of 33) of patients lost to follow-up before the minimum study follow-up of 2 years; these 19 patients were monitored over a period ranging from 70 to 115 months. A further 12 patients underwent this procedure from January 2018 to January 2022, with one lost to follow-up before the minimum study follow-up of 2 years; the other patients met the minimum 2-year follow-up requirement. The remaining 30 patients with data analyzed here (10 men, 20 women) had a mean ± SD age of 61 ± 12 years and a median BMI of 29 kg/m 2 (range 20 to 33 kg/m 2 ) at the time of revision surgery. Twenty-one patients underwent revision due to aseptic loosening, and nine due to periprosthetic joint infection (PJI). The causes of PD in our patients were as follows: cup aseptic loosening without significant osteolysis in 20% (6 of 30), where the loose cup caused erosion of the host bone, leading to PD; PJI in 30% (9 of 30); intraoperative iatrogenic PD in 3% (1 of 30); and osteolysis in 47% (14 of 30), which also resulted in aseptic loosening. The median follow-up time was 79 months (range 25 to 115 months). The Harris hip score was used to evaluate clinical outcomes, with preoperative values compared with the most recent follow-up. Radiographs were reviewed by two experienced surgeons at each follow-up visit to assess component loosening (defined as migration > 5 mm or the presence of circumferential radiolucent lines) or clear migration. PD was considered healed if bridging callus or trabecular bone was visible across the site of the discontinuity. Complications were assessed through a comprehensive review of electronic medical records. Kaplan-Meier analysis was used to estimate implant survivorship and radiographic loosening, with aseptic loosening or component migration as the endpoint, as well as survivorship free from any reoperation.

RESULTS

The Harris hip score improved from a median of 39 (range 30 to 66) preoperatively to a median of 76 (range 30 to 90) postoperatively (median difference 33 [range 2 to 48]; p < 0.01). Within the limitations of two-dimensional (2D) radiographic imaging, successful bone graft integration and the healing of PD were noted in 83% (25 of 30) of patients. Kaplan-Meier survivorship free from radiographic signs of aseptic loosening or component migration was 100% (95% CI 100% to 100%) at 115 months. When any revision related to the acetabular component was considered the endpoint, survivorship free from acetabular component revision at 115 months after revision surgery was 100% (95% CI 100% to 100%). When the need for any reoperation was considered the endpoint, survivorship free from needing reoperation at 115 months after revision surgery was 85% for all patients (95% CI 73% to 100%). When including only patients with a follow-up time of > 4 years (20 of 30), survivorship free from needing reoperation at 115 months after revision surgery was 90% (95% CI 78% to 100%). Postoperative complications during the follow-up period included one early dislocation on the fifth day after surgery, treated with closed reduction and 6 weeks of abduction bracing. One femoral stem loosening occurred at 56 months postoperatively, although the acetabular component remained securely fixed; this patient declined revision surgery. One patient experienced a dislocation 5 months after surgery but refused treatment and opted for prolonged bed rest. Additionally, one patient underwent a debridement, antibiotics, and implant retention procedure 1 week after the revision surgery and subsequently showed no signs of infection at the latest follow-up, 38 months postoperatively.

CONCLUSION

Our study highlights the effectiveness of a modified cup-cage technique in complex hip revisions, showing promising results in terms of construct survivorship and low complication rates. Surgeons could consider delaying screw fixation until after positioning the cage within the porous cup to allow for optimal adjustment and using metal augments for severe bone defects to achieve better alignment. Surgeon experience with the cup-cage technique is crucial for achieving optimal outcomes. Future studies should focus on long-term follow-up visits to assess the durability and effectiveness of these modifications and explore the comparative effectiveness versus other methods, such as custom triflange components and jumbo cups with distraction.

LEVEL OF EVIDENCE

Level III, therapeutic study.

Porous Metal Augments Have Comparable Outcomes to Other Constructs for Severe Acetabular Bone Loss at Mid-Term Follow-up

BACKGROUND

Acetabular reconstruction options in the setting of severe bone loss remain limited, with few comparative studies published to date. The purpose of this study was to compare the outcomes of revision total hip arthroplasty (THA) for severe bone loss using porous metal augments to cup cage and triflange prostheses.

METHODS

We reviewed a consecutive series of 180 patients who had Paprosky 3A or 3B acetabular defects and underwent revision THA. Patients treated with porous augments (n = 141) were compared with those who received cup cages or triflange constructs (n = 39). Failure of the acetabular construct was defined as undergoing acetabular revision surgery or radiographic evidence of loosening.

RESULTS

There was no difference in acetabular component survivorship in patients undergoing revision THA with porous augments or a cage or triflange prosthesis (92.2 versus 87.2%, P = .470) at a mean follow-up of 6.6 ± 3.4 years. Overall, survivorship free from any revision surgery was comparable between the 2 groups (78.7 versus 79.5%, P = .720). There was also no difference in dislocation (5.7 versus 10.3%, P = .309) or periprosthetic joint infection rates (7.8 versus 10.3%, P = .623). In a subgroup analysis of patients who had pelvic discontinuity (n = 47), survivorship free from any revision surgery was comparable between the 2 groups (79.5 versus 72.2%, P = .543).

CONCLUSIONS

Porous metal augments in the setting of severe acetabular bone loss demonstrated excellent survivorship at intermediate-term (mean 6.6 years follow-up, even in cases of pelvic discontinuity, with comparable outcomes to cup cages and triflanges. Instability and infection remain major causes of failure in this patient population, and long-term follow-up is needed.

Elastic properties of 3D printed clavicles are closer to cadaveric bones of elderly donors than commercial synthetic bones

Synthetic bone models have increasing utility in orthopaedic research due to their low cost and low variability and have been shown to be biomechanically equivalent to human bones in a variety of ways. The rise in additive manufacturing (AM) for orthopaedic applications presents an opportunity to construct synthetic whole-bone models for biomechanical testing applications, but there is a lack of research comparing these AM models to cadaveric or commercially available bone surrogates. This study compares the mechanical properties of 3D printed clavicle models to commercially available (4th generation Sawbones) and human cadaveric clavicles via nondestructive cyclic 4-point bending, axial compression, and torsion, and a final axial compression test to failure. Commercially available synthetic clavicles had 57.8-203% higher superior-inferior bending rigidity (p < 0.0001), 80.9-198% higher axial stiffness (p < 0.001), and 314-557% higher torsional rigidity (p < 0.05) on average than AM and cadaveric clavicles. Cadaveric and AM clavicles printed from a BoneMatrix/VeroWhite composite material had similar failure mechanisms under axial compression while AM VeroWhite clavicles experienced catastrophic failure, but these groups did not have significantly different ultimate failure loads. Together, these results demonstrate that current commercially available synthetic clavicles may be too rigid to emulate the mechanical properties of elderly cadaveric clavicles, and that AM bone models can closely mimic these cadaveric bones in a variety of biomechanical loading schemes. These results show promising applications for future work using 3D printed bone surrogates for biomechanical analysis of orthopaedic implants and other surgical repair techniques.

Heterotopic ossification following total hip arthroplasty. Which is the predominant risk factor: surgical approach or post-operative prophylaxis?

PURPOSE

To investigate the impact of surgical approach and post-operative prophylaxis on heterotopic ossification (HO) development after total hip arthroplasty (THA).

METHODS

A retrospective analysis of 312 patients who underwent THA between January 2009 and April 2016. Patients were categorized by surgical approach (direct lateral or posterolateral), prosthesis type, and post-operative prophylaxis (Etoricoxib 60 mg daily for two weeks). Two orthopaedic surgeons independently assessed radiographs at serial intervals, and HO was graded as per Brooker classification. Bivariate analysis and regression modelling were performed to assess the associations and confounding effects of different variables, RESULTS: Bivariate analysis identified factors correlated with higher HO incidence: absence of prophylaxis, older age, longer symptom evolution, and lower pre-surgery physical activity. Regression modelling showed a correlation between the direct-lateral approach, post-operative prophylaxis, symptom evolution, and higher HO incidence.

CONCLUSION

Patients with longer symptom evolution before surgery and without post-operative prophylaxis are at higher risk of developing HO. While the direct lateral approach showed higher HO rates, the difference was insignificant. A two-week prophylactic regimen of Etoricoxib 60 mg daily after THA effectively reduced HO formation. Pharmacological prophylaxis should be evaluated case-by-case, considering patient characteristics and risk factors.

Extended Trochanteric Osteotomy Does Not Compromise Functional and Radiographic Outcomes of Femoral Stem Revisions with the Use of an Uncemented Modular Conical Stem

Background: Stem revisions in revision total hip arthroplasty (THA) with proximal bone stock loss may be dealt with utilizing modular, uncemented conical stems. During stem extraction, surgeons may resort to extended trochanteric osteotomy (ETO). However, ETO is associated with extensive blood loss and infections. This study compared the clinical outcomes, radiographic results and complications in THA revisions utilizing conical modular stem with and without ETO. Methods: Patients who underwent revision THA with or without ETO were assessed retrospectively. The minimal follow-up was 3 years. The functional evaluation included Harris Hip Score (HHS) and Short Form 36 (SF-36) as well as Western Ontario and McMaster Universities Arthritis Index (WOMAC) and Numerical Rating Scale for pain assessment. The radiographic evaluation comprised bone defect assessment, osteotomy healing, stem migration and position, presence of radiolucent lines and stress shielding. Results: In total, 73 patients (80 hips) were included in the final analysis. The ETO group comprised 48 hips, and the no-ETO group comprised 32 hips. In the ETO group, pre-operative WOMAC scores were lower than in the no-ETO group (p = 0.012). No significant differences were found in terms of post-operative HHS, WOMAC, and NRS scores between groups, except worse results were found in the case of claw plate implantation. Patients in the no-ETO group exhibited better results in SF-36 than in the ETO-group. Osteotomy non-union was observed in four hips (9.5%). Stam varus/valgus position was within ±1.5 degrees (85.9%). Conclusions: ETO does not adversely impact outcomes in patients undergoing femoral stem revisions with modular conical stems. The invasive nature of these procedures prompts careful consideration in each case individually.

Long-term Survival of Hip Cement Spacer: A Case Report

We present a unique case of a 56-year-old male patient who ambulated on a hip cement spacer for 11 years. After hemiarthroplasty after a motor vehicle accident, the patient developed periprosthetic joint infection (PJI) several years later, and underwent stage-1 revision. With the resolution of the infection after stage 1, the patient refused the second stage due to satisfaction with the cement spacer for nearly 11 years. To our knowledge, this is the longest reported case of a cement spacer remaining in an ambulating patient. This case demonstrates the mechanical reliability of metal-reinforced cement spacers, which can remain for long periods in selected patients.

Minimum 2-Year Outcomes of a Modern Monoblock Titanium Fluted Tapered Revision Stem for Complex Primary and Revision Total Hip Arthroplasty

BACKGROUND

Modular titanium fluted tapered (TFT) stems have demonstrated excellent clinical success for femoral revision total hip arthroplasty (THA) surgery. This study reports the short-term outcomes of a novel modern monoblock TFT stem used for revision and complex primary THA with a minimum of 2 years of follow-up.

METHODS

We identified 126 patients who received a single monoblock TFT stem: 26 patients for complex THA (failed fracture fixation) and 100 patients for revision THA. The reasons for revision THA included 40 for previous periprosthetic joint infection, 42 for aseptic loosening, 9 for trunnionosis, and 9 for periprosthetic fractures. The Paprosky grading for femoral bone loss at the time of surgery and the measured subsidence of femoral stems at 3-month follow-up were determined. We evaluated the number and indications for reoperations.

RESULTS

The mean time from surgery was 3.9 years (range, 2.0 to 6.9). A paired t-test analysis showed significant improvement from preoperative versus postoperative clinical outcome scores (P < .001) for Harris Hip Score (38.76 ± 15.24 versus 83.42 ± 15.38), Western Ontario and McMaster Universities Arthritis Index (45.6 ± 19.0 versus 69.9 ± 21.3), Veterans RAND 12 Item Health Survey Physical component (31.7 ± 8.1 versus 37.8 ± 11.3), and Veterans RAND 12 Item Health Survey Mental component (48.2 ± 12.2 versus 51.6 ± 12.5). The Paprosky grading for femoral bone loss was Grade 1 (3.9%), Grade 2 (35.7%), Grade 3A (47.6%), Grade 3B (11.1%), and Grade 4 (1.6%) cases. There were 18 reoperations (14.7%), with 13 for periprosthetic joint infection (7 treated with implant retention and 6 treated with a 2-stage revision), 4 for instability, and 1 for acetabular aseptic loosening. There were no aseptic failures of the stem.

CONCLUSIONS

This novel modern monoblock TFT stem provided reliable femoral fixation and has increasingly supplanted the use of modular TFT stems for complex primary and revision surgery in our institution.

A Consecutive Series of Vancouver B2 Periprosthetic Femur Fractures Treated With Contemporary Monoblock Versus Modular Revision Stems: Clinical and Radiographic Outcomes

BACKGROUND

Tapered fluted titanium (TFT) stems are the implant design of choice for managing Vancouver B2 periprosthetic femur fractures (PFFs), producing reliable results over the past few decades. The aim of this study was to compare the radiographic and clinical outcomes of Vancouver B2 PFFs treated with contemporary monoblock versus modular TFTs.

METHODS

A consecutive series of 113 patients (72 women, 64%, mean age 70 years [range, 26 to 96]) who had a B2 PFF were treated with either a monoblock (n = 42) or modular (n = 71) TFT stem between 2008 and 2021. The mean body mass index was 30 ± 7. The mean follow-up was 2.9 years. A radiographic review was performed to assess leg length and offset restoration, endosteal cortical contact length, and stem subsidence. Kaplan-Meier analyses were used to determine survivorship without revision, reoperation, or dislocation.

RESULTS

There was no difference in the restoration of leg length (0.3 ± 8.0 mm) or offset (2.8 ± 8.2 mm) between the monoblock and modular cohorts (P > .05). Mean endosteal cortical contact length (47.2 ± 26.6 versus 46.7 ± 2 6.4 mm, P = .89) and stem subsidence (2.7 ± 3.5 versus 2.4 ± 3.2 mm, P = .66) did not differ. No difference in patient-reported outcome measures (Hip Disability and Osteoarthritis Outcome Score-Joint Replacement; Veterans RAND 12 Item Health Survey Physical and Mental; visual analog score; and Lower Extremity Activity Scale) between the groups was observed. Survivorship at 2 years free from reoperation, revision, and dislocation was 90.4, 90.3, and 97.6%, respectively, for the monoblock cohort; and 84.0, 86.9, and 90.0%, respectively, for the modular cohort.

CONCLUSIONS

No significant differences in radiographic or clinical outcomes were observed between patients treated with monoblock or modular TFTs in this large series of B2 PFFs.

Accuracy Analysis of 3D Bone Fracture Models: Effects of Computed Tomography (CT) Imaging and Image Segmentation

The introduction of three-dimensional (3D) printed anatomical models has garnered interest in pre-operative planning, especially in orthopedic and trauma surgery. Identifying potential error sources and quantifying their effect on the model dimensional accuracy are crucial for the applicability and reliability of such models. In this study, twenty radii were extracted from anatomic forearm specimens and subjected to osteotomy to simulate a defined fracture of the distal radius (Colles' fracture). Various factors, including two different computed tomography (CT) technologies (energy-integrating detector (EID) and photon-counting detector (PCD)), four different CT scanners, two scan protocols (i.e., routine and high dosage), two different scan orientations, as well as two segmentation algorithms were considered to determine their effect on 3D model accuracy. Ground truth was established using 3D reconstructions of surface scans of the physical specimens. Results indicated that all investigated variables significantly impacted the 3D model accuracy (p < 0.001). However, the mean absolute deviation fell within the range of 0.03 ± 0.20 to 0.32 ± 0.23 mm, well below the 0.5 mm threshold necessary for pre-operative planning. Intra- and inter-operator variability demonstrated fair to excellent agreement for 3D model accuracy, with an intra-class correlation (ICC) of 0.43 to 0.92. This systematic investigation displayed dimensional deviations in the magnitude of sub-voxel imaging resolution for all variables. Major pitfalls included missed or overestimated bone regions during the segmentation process, necessitating additional manual editing of 3D models. In conclusion, this study demonstrates that 3D bone fracture models can be obtained with clinical routine scanners and scan protocols, utilizing a simple global segmentation threshold, thereby providing an accurate and reliable tool for pre-operative planning.

Partial Shoulder Arthroplasty Guided by Three-dimensional Prototyping

Three-dimensional (3D) printing technology is a reality in medicine. In Orthopedics and Traumatology, 3D printing guides a precise and tailored surgical treatment. Understanding and disseminating its applicability, use, and outcomes can foster academicism and improve patient care. This is a report of a rare case of a female young adult patient with osteonecrosis of the humeral head due to avascular necrosis developed in early childhood. The treatment was tailored and optimized with 3D printing, which helped determine the steps for partial humeral arthroplasty.

Three-dimensional printed models for surgery planning of post-traumatic stiff elbow: Current concepts

The post-traumatic stiff elbow is a challenge for the surgeon, requiring expertise for the treatment choice and accurate planning. Stiffness can result from traumatic injury involving the periarticular soft tissues and the joint articular surfaces. In this article, we want to assess the impact of three-dimensional (3D) printed models in selecting the appropriate surgical strategy for this pathology. Six cases of increasing complexity regarding post-traumatic stiff elbow were submitted to four expert elbow surgeons who had the possibility to evaluate videos and reports of clinical examination, plain radiograms and CT with 3D reconstruction for each case. After a first treatment proposition given by the experts for each patient, a three-dimensional printed model of each elbow based on the CT was provided to the surgeons, asking them to evaluate again all the cases having the possibility to assess also the 3D models. In the four most complex cases all surgeons found more beneficial the use of three-dimensional representation for treatment planning and rate the risk of complications than the sole CT imaging with 3D reconstruction and many of them changed surgical strategy after analysing the model. 3D printing technology is a useful tool in surgery planning for treating complex cases of post traumatic elbow stiffness, especially in the presence of joint deformity. LEVEL OF EVIDENCE: IV.

Management of Severe Bone Defects in Femoral Revision following Total Hip Arthroplasty

Treatment of femoral bone defects continues to be a challenge in revision total hip arthroplasty (THA); therefore, meticulous preoperative evaluation of patients and surgical planning are required. This review provides a concise synopsis of the etiology, classification, treatment strategy, and prosthesis selection in relation to femoral bone loss in revision THA. A search of literature was conducted for identification of research articles related to classification of bone loss, management of femoral revision, and comparison of different types of stems. Findings of a thorough review of the included articles were as follows: (1) the Paprosky classification system is used most often when defining femoral bone loss, (2) a primary-length fully coated monoblock femoral component is recommended for treatment of types I or II bone defects, (3) use of an extensively porouscoated stem and a modular fluted tapered stem is recommended for management of types III or IV bone defects, and (4) use of an impaction grafting technique is another option for improvement of bone stock, and allograft prosthesis composite and proximal femoral replacement can be applied by experienced surgeons, in selected cases, as a final salvage solution. Stems with a tapered design are gradually replacing components with a cylindrical design as the first choice for femoral revision; however, further confirmation regarding the advantages and disadvantages of modular and nonmodular stems will be required through conduct of higher-level comparative studies.

Ossification of Bilateral Sacrotuberous Ligaments: Two Cases Report and Literature Review

Ossification of the sacrotuberous ligament is a rare occurrence in soft tissue, with only 15 cases reported in the past few decades. We reported two cases of bilateral ossification in sacrotuberous ligaments and provided a concise review of the literature on this pathology. Clinical data, radiographic outcomes, and diagnostic and treatment details were obtained. This study aimed to summarize this disease's characteristics and investigate its pathogenesis through a review of literature from the last thirty years. This condition is often incidentally confirmed in elderly males via imagiological examination or gross anatomy and presents a low morbidity rate. Its pathogenesis may be related to stress concentration, excessive intake of element ions, injury repair, and improper operative technique. The majority of patients may not exhibit any clinical symptoms or signs and typically do not require medical interventions. It may be complicated with pudendal nerve entrapment syndrome. The long-term effects of surgical resection and the most effective treatment approach remain areas for further research.

The Novel Impact of Augmented Reality and 3D Printing in the Diagnosis of Complex Acetabular Fractures: A Comparative Randomized Study in Orthopedic Residents

Augmented reality (AR) and 3D printing (3DP) are novel technologies in the orthopedic field. Over the past decade, enthusiasm for these new digital applications has driven new perspectives in improving diagnostic accuracy and sensitivity in the field of traumatology. Currently, however, it is still difficult to quantify their value and impact in the medical-scientific field, especially in the improvement of diagnostics in complex fractures. Acetabular fractures have always been a challenge in orthopedics, due to their volumetric complexity and low diagnostic reliability. Background/Objectives: The goal of this study was to determine whether these methods could improve the learning aspect and diagnostic accuracy of complex acetabular fractures compared to gold-standard CT (computed tomography). Methods: Orthopedic residents of our department were selected and divided into Junior (JUN) and Senior (SEN) groups. Associated fractures of acetabulum were included in the study, and details of these were provided as CT scans, 3DP models, and AR models displayed on a tablet screen. In a double-blind questionnaire, each resident classified every fracture. Diagnostic accuracy (DA), response time (RT), agreement (R), and confidence (C) were measured. Results: Twenty residents (JUN = 10, SEN = 10) classified five fractures. Overall DA was 26% (CT), 18% (3DP), and 29% (AR). AR-DA was superior to 3DP-DA (p = 0.048). DA means (JUN vs. SEN, respectively): CT-DA was 20% vs. 32% (p < 0.05), 3DP-DA was 12% vs. 24% (p = 0.08), and AR-DA was 28% vs. 30% (p = 0.80). Overall RT was 61.2 s (±24.6) for CT, 35.8 s (±20.1) for 3DP, and 46.7 s (±20.8) for AR. R was fairly poor between methods and groups. Overall, 3DPs had superior C (65%). Conclusions: AR had the same overall DA as CT, independent of experience, 3DP had minor differences in DA and R, but it was the fastest method and the one in which there was the most confidence. Intra- and inter-observer R between methods remained very poor in residents.

An unusual case of traumatic injury to the first metatarsal a case report

A 44-year-old male sustained trauma to his foot leading to a 5-cm defect of the first metatarsal bone and infection of the bone by Staphylococcus aureus. Osteotomy is the most suitable method for treating large metatarsal defects complicated with osteomyelitis, however few reports have been published on this challenging approach. In this case, osteotomy and external fixation for distraction were performed. Finally, the osteomyelitis of the patient was well controlled, the bone length was restored, and the patient could carry weight completely, and the treatment effect was satisfactory.

Comparative analysis of GoPro and digital cameras in head and neck flap harvesting surgery video documentation: an innovative and efficient method for surgical education

BACKGROUND

An urgent need exists for innovative surgical video recording techniques in head and neck reconstructive surgeries, particularly in low- and middle-income countries where a surge in surgical procedures necessitates more skilled surgeons. This demand, significantly intensified by the COVID-19 pandemic, highlights the critical role of surgical videos in medical education. We aimed to identify a straightforward, high-quality approach to recording surgical videos at a low economic cost in the operating room, thereby contributing to enhanced patient care.

METHODS

The recording was comprised of six head and neck flap harvesting surgeries using GoPro or two types of digital cameras. Data were extracted from the recorded videos and their subsequent editing process. Some of the participants were subsequently interviewed.

RESULTS

Both cameras, set at 4 K resolution and 30 frames per second (fps), produced satisfactory results. The GoPro, worn on the surgeon's head, moves in sync with the surgeon, offering a unique first-person perspective of the operation without needing an additional assistant. Though cost-effective and efficient, it lacks a zoom feature essential for close-up views. In contrast, while requiring occasional repositioning, the digital camera captures finer anatomical details due to its superior image quality and zoom capabilities.

CONCLUSION

Merging these two systems could significantly advance the field of surgical video recording. This innovation holds promise for enhancing technical communication and bolstering video-based medical education, potentially addressing the global shortage of specialized surgeons.

Enhancing Hip Arthroplasty Outcomes: The Multifaceted Advantages, Limitations, and Future Directions of 3D Printing Technology

In the evolving field of orthopedic surgery, the integration of three-dimensional printing (3D printing) has emerged as a transformative technology, particularly in addressing the rising incidence of degenerative joint diseases. The integration of 3D printing technology in hip arthroplasty offers substantial advantages throughout the surgical process. In preoperative planning, 3D models enable meticulous assessments, aiding in accurate implant selection and precise surgical strategies. Intraoperatively, the technology contributes to precise prosthesis design, reducing operation duration, X-ray exposures, and blood loss. Beyond surgery, 3D printing revolutionizes medical equipment production, imaging, and implant design, showcasing benefits such as enhanced osseointegration and reduced stress shielding with titanium cups. Challenges include a higher risk of postoperative infection due to the porous surfaces of 3D-printed implants, technical complexities in the printing process, and the need for skilled manpower. Despite these challenges, the evolving nature of 3D printing technologies underscores the importance of relying on existing orthopedic surgical practices while emphasizing the need for standardized guidelines to fully harness its potential in improving patient care.

Utilizing an antibiotic-eluting articulated cemented spacer in the two-stage management of infected total hip arthroplasty: a technical note

Two-stage revision is generally preferred to eradicate chronic periprosthetic infections after total hip arthroplasty (THA) because of its good infection control and promising results. During two-stage revision, a temporary antibiotic-impregnated cement spacer was initially used for the local delivery of antibiotics, thereby reducing the risk of infection recurrence. Many researchers have reported various techniques for fabricating cemented spacers; however, there is no established standard technique. We share our cost-effective and easily reproducible technique for creating an articulated cemented spacer for managing infected THA.

Improving Patient Understanding of Femoroacetabular Impingement Syndrome With Three-Dimensional Models

INTRODUCTION

Three-dimensional (3D) printed models may help patients understand complex anatomic pathologies such as femoroacetabular impingement syndrome (FAIS). We aimed to assess patient understanding and satisfaction when using 3D printed models compared with standard imaging modalities for discussion of FAIS diagnosis and surgical plan.

METHODS

A consecutive series of 76 new patients with FAIS (37 patients in the 3D model cohort and 39 in the control cohort) from a single surgeon's clinic were educated using imaging and representative 3D printed models of FAI or imaging without models (control). Patients received a voluntary post-visit questionnaire that evaluated their understanding of the diagnosis, surgical plan, and visit satisfaction.

RESULTS

Patients in the 3D model cohort reported a significantly higher mean understanding of FAIS (90.0 ± 11.5 versus 79.8 ± 14.9 out of 100; P = 0.001) and surgery (89.5 ± 11.6 versus 81.0 ± 14.5; P = 0.01) compared with the control cohort. Both groups reported high levels of satisfaction with the visit.

CONCLUSION

In this study, the use of 3D printed models in clinic visits with patients with FAIS improved patients' perceived understanding of diagnosis and surgical treatment.

Fracture of femoral neck in modular total hip arthroplasty: a systematic review of the literature

BACKGROUND

Modular femoral stems have the advantage of anatomic hip reconstruction by restoring the femoral offset thus minimising the bearing surface wear, implant loosening and dislocation.

AIM

This study aims to investigate the existing literature on modular neck fractures, to identify predisposing factors and guide the decision-making process in the management of these difficult cases.

METHODS

A systematic literature review was conducted until July 2022. PRISMA guidelines were followed, eligibility criteria were set, and methodology assessment of included studies was conducted based on MINORS criteria, size and primary outcome. Data were extracted and analysed thoroughly.

RESULTS

5657 studies were initially screened; the full texts of 124 records were assessed and finally, 32 reports were included. There were 7 clinical studies and 25 case reports. A total of 4825 patients (5204 hips) with a mean age 62.38 years and a mean BMI 29.06 kg/m2 were analysed in the 7 clinical studies. The reported overall weighted revision rate was 0.86%, while the weighted mean modular neck fracture rate was 0.26%. The usual history was sudden experience of hip pain and instability. The average time interval to neck fracture was 4.57 (range 3-4.7) years and a long modular neck was identified in 91.17% of them. Data from case reports showed a mean age and average BMI of 55.85 and 31.63 kg/m2. 82.35% of the patients were male. Necks were fractured after an average time interval of 64.5 ± 8.8 months.

CONCLUSIONS

The incidence of modular neck fracture is significant. The profile of a male, obese patient with a long modular neck increased risk of neck fracture. Microstructural investigation of the retrieved implants demonstrated a higher incidence of fracture line in the base of the neck junction and at its anterolateral distal part. Surgeons should be aware of this complication while using or revising such protheses.

Anterior Minimally Invasive Approach (AMIS) for Total Hip Arthroplasty: Analysis of the First 1000 Consecutive Patients Operated at a High Volume Center

(1) Background: Direct anterior approach (DAA) has recently acquired popularity through improvements such as the anterior minimally invasive surgical technique (AMIS). This retrospective study examines the first 1000 consecutive THAs performed utilizing the AMIS approach in a high-volume center between 2012 and 2017. (2) Methods: 1000 consecutive THAs performed at a single institution utilizing the AMIS approach were retrospectively analyzed with a minimum five-year follow-up. Full evaluation of demographic information, clinical parameters, intraoperative complications, and radiological examinations are reported. (3) Results: Overall complication rate was 9.4% (94/1000), including 8 dislocations, 57 femoral-cutaneous nerve injuries, 12 intraoperative femoral fractures, 9 infections and 8 leg length discrepancy. Implant survival rates were 98.5% at 1 year, 97.5% at 3 years, 97% at 5 years, and 95.3% at 7 years. Causes of failure included periprosthetic fractures (0.8%), implant dislocations (0.6%), septic loosening (0.5%), aseptic mobilizations (0.2%), and symptomatic limb length discrepancies (0.2%). (4) Conclusions: Controversies persist around the direct anterior approach (DAA) for THA, primarily regarding the increased complications rate during the learning curve. However, this study advocates for widespread adoption of the DAA approach. The results demonstrate acceptable complication rates and remarkable functional outcomes, affirming its viability in the broader orthopedic patient population.

A Very Rare Form of Ceramic Head Fracture in Bipolar Hemiarthroplasty and Total Hip Arthroplasty: Unique Experience and Literature Review

Introduction

A fracture of the ceramic head in bipolar hemiarthroplasty using an inner polyliner has not been reported yet, and there seems to be no report of simultaneous breakage of the fourth-generation BIOLOX Delta ceramic head and liner in total hip arthroplasty.

Method

A 44-year-old male patient underwent bipolar hemiarthroplasty using a third-generation BIOLOX Forte ceramic head 3 years and 9 months earlier for osteonecrosis of femoral head (ONFH) and visited our hospital due to a ceramic head fracture. Conversion total hip arthroplasty was performed. A 64-year-old female patient underwent total hip arthroplasty using a fourth-generation BIOLOX Delta ceramic head and liner articulation for osteoarthritis of the hip. The ceramic head and liner were fractured during the third dislocation. Ceramic head and liner exchange revision surgery was performed.

Conclusion

When using ceramic bearings, fractures or delamination following trauma can occur, confirming the need to carefully evaluate the condition of the ceramic components in symptomatic patients.

Three-dimensional printed models can reduce costs and surgical time for complex proximal humeral fractures: preoperative planning, patient satisfaction, and improved resident skills

BACKGROUND

Proximal humeral fractures (PHFs) are still controversial with regards to treatment and are difficult to classify. The study's objective is to show that preoperative planning performed while handling a three-dimensional (3D) printed anatomical model of the fracture can ensure a better understanding of trauma for both surgeons and patients.

MATERIALS AND METHODS

Twenty patients (group A, cases) with complex PHF were evaluated preoperatively by reproducing life-size, full-touch 3D anatomical models. Intraoperative blood loss, radiographic controls, duration of surgery, and clinical outcomes of patients in group A were compared with 20 patients (group B, controls) who underwent standard preoperative evaluation. Additionally, senior surgeons and residents, as well as group A patients, answered a questionnaire to evaluate innovative preoperative planning and patient compliance. Cost analysis was evaluated.

RESULTS

Intraoperative radiography controls and length of operation were significantly shorter in group A. There were no differences in clinical outcomes or blood loss. Patients claim a better understanding of the trauma suffered and the proposed treatment. Surgeons assert that the planning of the definitive operation with 3D models has had a good impact. The development of this tool has been well received by the residents. The surgery was reduced in length by 15%, resulting in savings of about EUR 400 for each intervention.

CONCLUSIONS

Fewer intraoperative radiography checks, shorter surgeries, and better patient compliance reduce radiation exposure for patients and healthcare staff, enhance surgical outcomes while reducing expenses, and lower the risk of medicolegal claims.

LEVEL OF EVIDENCE

Level I, prospective randomized case-control study.

Ceramic fragmentation after total hip arthroplasty: two case reports and literature review

Background

Ceramic fragmentation is a rare but serious complication after total hip arthroplasty (THA). We reviewed the PubMed literature from 1990 to 2023 and found only 31 case reports of ceramic fragmentation after THA. Our case reports help to expand understanding of this rare complication. We shared our surgical experience and identified an ideal material for revision surgery, which can serve as a useful reference for other orthopedic surgeons to perform ceramic fragmentation revision surgery in the future. We also analyzed the possible causes, diagnosis, and treatment opinions of ceramic fragmentation.

Case presentation

This study presents two cases of ceramic fragmentation after THA. One patient had ceramic head fragmentation 10 years after the primary THA, and one patient had ceramic liner fragmentation 5 years after the primary THA. Both patients presented with pain, and one patient also reported a clicking sound in the hip. The two patients described here had BMIs of 23.7 and 23.1, respectively. Both patients' ceramic fragmentation were due to aseptic loosening, not periprosthetic joint infections, as confirmed by negative microbiological cultures. Radiographic examinations of both patients revealed radio-opaque wear debris around the hip joint prostheses and we describe the surgical protocols and intraoperative findings in both cases in detail.

Conclusion

Our cases and the literature suggest that ceramic fragmentation can occur at any time after THA. The most immediate symptoms are pain and noise, but some patients may be asymptomatic. Ceramic on polyethylene bearings is recommended for revision surgery whenever possible; metal bearings should be avoided.

Patellar Tendon Reconstruction Using Tibialis Posterior Allograft for Treatment of Patellar Tendon Rupture After Bone-Patellar Tendon-Bone Anterior Cruciate Ligament Reconstruction

Background: Bone-patellar tendon-bone (BPTB) autografts are often used to treat anterior cruciate ligament (ACL) tears in young, highly active patients. These grafts are robust and provide adequate stability, allowing for return to sport and optimal functional outcomes in athletes. Patellar tendon rupture following BPTB ACL reconstruction is rare and can be difficult to treat. Case Report: A 19-year-old collegiate wrestler injured his left knee during a match. On evaluation 7 days after the injury, he was found to have increased anterior translation of the tibia on Lachman testing and an abnormal pivot shift. Magnetic resonance imaging demonstrated a complete tear of the ACL, and he successfully underwent a BPTB ACL reconstruction without complication. He progressed appropriately in the acute postoperative period. Six weeks after his index surgery, the patient reinjured his left knee and was diagnosed with a patellar tendon rupture. The previously reconstructed ACL was intact. A posterior tibialis tendon graft was used to repair the patellar tendon via a transosseous tunnel in the tibial tuberosity. The patient's recovery was complicated by a superficial wound that resolved with treatment. He achieved full range of motion and was able to return to sport. Conclusion: No technique for treating patellar tendon rupture following BPTB ACL reconstruction has been widely accepted. The treatment of this injury is left to the preference of the surgeon. This case demonstrates that tibialis posterior allografts are a viable option for the treatment of such injuries.

The 'Holy Grail' of shoulder dislocations: a systematic review on traumatic bilateral luxatio erecta; is it in reality a once-in-a-lifetime experience for an orthopaedic surgeon?

INTRODUCTION

Even though shoulder dislocation is thought to be the most common dislocation treated in the Emergency Department, inferior ones, known as Luxatio Erecta, comprise only 0.5% of them. Taking into consideration the rareness of unilateral Luxatio Erecta, bilateral cases should be even fewer. The purpose of this paper is to identify the reported number of cases of Traumatic Bilateral Luxatio Erecta in the literature over the last 100 years and to summarize the mechanism of injury, the initial management, and the complications of these patients.

MATERIALS AND METHODS

We performed a systematic review of the literature regarding Traumatic Bilateral Luxatio Erecta. All articles published until 31st of December 2022 in PubMed and Google Scholar databases were searched using the terms "luxatio erecta", 'inferior dislocation", and "bilateral".

RESULTS

Eighty-two articles were retrieved from PubMed and Google Scholar search. Forty-four of them were initially included in our review. Six additional articles meeting the inclusion criteria were found from cross-references.

CONCLUSION

The presence of this injury is extremely rare with only 51 cases in the literature. The incidence of concomitant injuries and complications seems to be extremely high and neurological deficits were detected on 42.8% of patients with Bilateral Luxatio Erecta. To our knowledge, this is the first systematic review of the literature regarding Traumatic Bilateral Luxatio Erecta that includes articles not only in English, a fact that provides more reliability on the estimation of the real number of cases of this rare injury compared to any other review on this subject to date.

Mid-term clinical and radiographic outcome of metal-on-metal hip resurfacing through an anterolateral approach

PURPOSE

The aim of this retrospective study was to evaluate the medium-term clinical and radiographic results of current generation metal-on-metal resurfacing prostheses performed through anterolateral approach.

MATERIALS AND METHODS

Fifty-seven hips in 52 patients underwent resurfacing arthroplasty. Two patients died from unrelated causes, leaving 55 hips in 35 males (3 bilateral) and 15 females (2 bilateral), with a mean age at surgery of 56.2 years (range, 27-70 years). Clinical and radiographic assessment was carried out preoperatively and at follow-up in all the survived cases. The cumulative survival rate was determined according to the method of Kaplan-Meier.

RESULTS

At a mean follow-up of 5.2 years (range, 1.8-9.1 years), 2 HRs of the same female patient were revised because of early loosening of the acetabular component. Deep venous thrombosis and transient femoral nerve palsy occurred both in 1 case. No specific complications of HR were observed. Average Harris hip score improved significantly from 59.8 points (range, 30.4-90.6) preoperatively to 93.7 points (range, 53-100) at the latest examination. Neck narrowing showed an average of 3.27%, but it never exceeded 10%. Nonprogressive acetabular radiolucencies and osteolysis were detected both in 2 hips. A high rate of patients (32, 60.4%) developed heterotopic ossifications, although low-grade in most cases (27, 84.4%). The cumulative survival rate at 9.1 years with revision for any reason as the end point was 93.0%.

CONCLUSIONS

The early clinical and radiographic results of modern metal-on-metal hip resurfacing performed through an anterolateral approach are promising, but longer-term follow-up studies are necessary.

A new risk predictive scoring system of vasovagal reactions in patients with preoperative autologous blood donation

BACKGROUND AND OBJECTIVES

Vasovagal response (VVR) is the most common adverse reaction during blood donation and it is the main element for the safety of the patients with preoperative autologous blood donation (PABD). Accurate identification high-risk group is of great significance for PABD. Our study aimed to establish a scoring system based on the nomogram to screen the high-risk population and provide evidence for preventing the occurrence of VVRs.

MATERIALS AND METHODS

A number of 4829 patients underwent PABD between July 2017 and June 2020 in the first medical center of Chinese PLA Hospital were recruited, 3387 of whom were included in the training group (70 %; 108 VVRs patients vs 3279 Non-VVRs patients), 1442 were included in the validation group (30 %; 46 VVRs patients vs 1396 Non-VVRs patients). The data were analyzed by univariate and multivariate logistic regression. The nomogram of the scoring system was created by using the RMS tool in R software.

RESULTS

Seven variables including BMI, hematocrit, pre-phlebotomy heart rate and systolic blood pressure, history of blood donation, age group and primary disease were selected to build the nomogram, which was shown as prediction model. And the score was 0-1 for BMI, 0-2 for hematocrit, systolic blood pressure, heart rate and no blood donation history, 0-10 for age, 0-3 for primary disease. When the total cutoff score was 11, the predictive system for identifying VVRs displayed higher diagnostic accuracy. The area under the curve, specificity, and sensitivity of the training group were 0.942, 82.41 % and 97.17 %, respectively, whereas those of the validation group were 0.836, 78.26 % and 78.15 %, respectively.

CONCLUSION

A risk predictive scoring system was successfully developed to identify high-risk VVRs group form PABD patients that performed well.

Extra-capsular floating fat at the extremity: a review

Extra-capsular floating fat may present in a variety of non-articular locations at the extremity. Manifestation of floating fat or fat-fluid level(s) outside of a joint is a marker of trauma or infection. Recognizing radiologic sign(s) of extra-capsular floating fat can aid radiologists to provide an informed differential diagnosis and facilitate clinical care. This review discusses the etiology, mechanisms, and imaging appearance of extracapsular floating fat in specific anatomic and non-anatomic locations at the extremity.

Simple and cost-effective way to make mobile antibiotic cement spacer: hand-made silicone mold

BACKGROUND

Two-stage exchange arthroplasty is considered the most common approach for the management of prosthetic joint infections. There has been plentiful evidence to support the superiority of the mobile spacers over the static ones. Unfortunately, articulating options are not available in our low-resource environment, which motivated us to come up with an affordable way to create a mobile cement spacer. After experimenting with a variety of materials and producing methods, we realized that silicone is a favorable material for mold building and established a simple process of making a handmade silicone mold. We demonstrate the clinical outcomes of three prosthetic joint infections by using these spacers in the hope of spreading the idea to our colleagues who work in the circumstances of a developing country. Construction of the spacer molds: The molds, consisting of two parts, were shaped by using high viscosity addition silicone (elite HD+ putty soft, Zhermack SpA, Italy) as material, and previously removed implants as template. They were sterilized using ethylene oxide treatment before being ready for casting antibiotic-loaded bone cement spacer.

CASE REPORT

Three cases of prosthetic infection were treated with two-stage revision, using antibiotic-impregnated cement spacer cast in hand-made silicone molds. We sought to determine intraoperative complications, postoperative range of motion, and functional scores. All the patients were regularly followed up to identify fractures or dislocation of the spacer, and reinfection.

RESULTS

At the end of the follow-up, all three patients had the infection eradicated. The three patients could sit comfortably with bent knees, walk with partial weight-bearing, and achieve 75-80 degrees of knee flexion in the first week after surgery. Follow-up X-rays revealed no fractures or dislocation in any of the spacers.

CONCLUSION

Silicone molds offer a simple and cost-effective alternative to costly commercial products in producing articulating spacers. Treating infected joints arthroplasty with these spacers allows for early motion and partial weight bearing and improves patient satisfaction and life quality before reimplantation without significant complications.