Determination of Mercury by Anodic Stripping Voltammetry with a Gold Nanoparticle-Modified Glassy Carbon Electrode

Electrochemical detection of mercury using biosynthesized hydroxyapatite nanoparticles modified glassy carbon electrodes without preconcentration

An electrochemical method for the determination of trace levels of mercury(ii) ions using Aloe vera (Av) assisted hydroxyapatite (HA) nanoparticles modified glassy carbon electrode (GCE) by square wave voltammetry is described for the first time.

A highly sensitive hemicyanine-based fluorescent chemodosimeter for mercury ions in aqueous solution and living cells

A novel hemicyanine-based fluorescence turn-on chemodosimeter for Hg²⁺ by mercury triggered hydrolysis of vinyl ether group has been reported.

Graphene-based sensors for detection of heavy metals in water: a review

Graphene (G) is attracting significant attention because of its unique physical and electronic properties. The production of graphene through the reduction of graphene oxide (GO) is a low-cost method. The reduction of GO can further lead to electrically conductive reduced GO. These graphene-based nanomaterials are attractive for high-performance water sensors due to their unique properties, such as high specific surface areas, high electron mobilities, and exceptionally low electronic noise. Because of potential risks to the environment and human health arising from heavy-metal pollution in water, G-/GO-based water sensors are being developed for rapid and sensitive detection of heavy-metal ions. In this review, a general introduction to graphene and GO properties, as well as their syntheses, is provided. Recent advances in optical, electrochemical, and electrical detection of heavy-metal ions using graphene or GO are then highlighted. Finally, challenges facing G/GO-based water sensor development and outlook for future research are discussed.

Optimization of analytical procedures for the simultaneous voltammetric determination of total Hg(II) in presence of Cu(II) in environmental matrices

The present work reports the critical comparison about the employment of three different supporting electrolytes (0.1 mol L−1 HClO4, 0.01 mol L−1 EDTA-Na2 + 0.06 mol L−1 NaCl + 2.0 mol L−1 HClO4 and 0.1 mol L−1 KSCN + 0.001 mol L−1 HClO4) and their instrumental and chemical optimisation for the simultaneous voltammetric determination of total mercury(II) and copper(II) in sediments and sea water at gold electrode, especially discussing the reciprocal interference problems.

The differential pulse anodic stripping voltammetric (DPASV) measurements were carried out using a conventional three-electrode cell: a gold electrode (GE) as working electrode, a platinum wire and an Ag‖AgCl‖KClsat as auxiliary and reference electrodes, respectively.

The analytical procedure was verified by the analysis of standard reference materials: Estuarine Sediment BCR-CRM 277, River Sediment BCR-CRM 320 and Mercury in Water NIST-SRM 1641d.

Once set up on the standard reference materials, the analytical procedure was transferred and applied to sediments and sea waters sampled in a lagoon ecosystem connected with Adriatic Sea (Ravenna area, Italy).

Determination of As(III) by anodic stripping voltammetry using a lateral gold electrode: experimental conditions, electron transfer and monitoring of electrode surface

The aim of this work is to evaluate the efficiency of the determination of As(III) by anodic stripping voltammetry (ASV) using a lateral gold electrode and to study the modifications of the electrode surface during use. Potential waveforms (differential pulse and square wave), potential scan parameters, deposition time, deposition potential and surface cleaning procedure were examined for they effect on arsenic peak intensity and shape. The best responses were obtained with differential pulse potential wave form and diluted 0.25 M HCl as supporting electrolyte. The repeatability, linearity, accuracy and detection limit of the procedure and the interferences of cations and anions in solution were evaluated. The applicability of the procedure for As(III) determination in drinking waters was tested. Cyclic voltammetry (CV) was used to study the electrochemical behaviour of As(III) and for the daily monitoring of electrode surface. Also scanning electron microscopy (SEM) analysis was used to control the electron surface. Finally we evaluated the possibility to apply the equations valid for flow systems also to a stirred system, in order to calculate the number of electrons transferred per molecule during the stripping step.