Protein adsorption to poly(ethylenimine)-modified Sepharose FF: II. Effect of ionic strength

Highly efficient separation, enrichment, and recovery of peptides by silica-supported polyethylenimine

Highly efficient and charge-selective adsorption and desorption of peptides at trace level by a solid-phase adsorbent is described. The adsorbent of SiO2@PEI is synthesized by covalent immobilization of branched polyethylenimines (PEI) exclusively on the outer surface of the porous silica particles (∼300 μm). For aqueous peptides (Mw = 600-3000 Da), SiO2@PEI can capture the negatively charged ones and leave the positively charged ones intact, and by adjusting pH of the system peptides with different isoelectric points (pIs) can be well separated. Targeted peptide at low abundance (at least as low as 0.1 mol % with respect to the highest one) can be well separated. The association constants of K > 10(12) M(-1) at pH > pI and K < 10(4) M(-1) at pH < pI are found; that is, selectivity > 10(8) is generally available. Thus, a peptide even at sub-femtomolar level can be extracted and eluted for analysis, and efficient recovery (79-92%) of the peptides is found. The extraction is mainly promoted by multisite electrostatic interaction, and the hydrophilic and cationic properties of PEI at low pH play a unique role in desorption efficiency and selectivity. The unbiased nature of this method renders the adsorbent applicable to the efficient separation of a broad spectrum of peptides, including those with similar pIs.

Protein adsorption to poly(ethylenimine)-modified Sepharose FF. IV. Dynamic adsorption and elution behaviors

We have previously investigated bovine serum albumin (BSA) uptake to poly(ethylenimine) (PEI)-grafted Sepharose FF. It was found that there was a critical ionic capacity (cIC; 600mmol/L) for BSA, above which the protein adsorption capacity and uptake kinetics increased drastically. In this work, two poly(ethylenimine) (PEI)-grafted resins with IC values of 271mmol/L (FF-PEI-L270) and 683mmol/L (FF-PEI-L680), which were below and above the cIC, respectively, were chosen to investigate the breakthrough and linear gradient elution (LGE) behaviors of BSA. Commercially available anion exchanger, Q Sepharose FF, was used for comparison. The DBC values of FF-PEI-L680 were much higher in the entire residence time range (2-10min) than the other two resins due to its high static adsorption capacity and uptake kinetics. At a residence time of 5.0min, the DBC of FF-PEI-L680 (104mg/mL) was about seven times that of FF-PEI-L270 and three times that of Q Sepharose FF. A rise-fall trend of the DBCs with increasing ionic strength (IS) was found for all the three resins studied, indicating the presence of electrostatic exclusion for protein uptake at low IS. With increasing NaCl concentration from 20 to 200mmol/L, FF-PEI-L680 kept very high DBC values (64-114mg/mL). In addition, FF-PEI-L270 showed more favorable adsorption properties than Q Sepharose FF at 100-300mmol/L NaCl. These results proved that the three-dimensional grafting ion exchange layer on the PEI resins enhanced their tolerance to IS. In the study of LGE, the three resins showed similar elution behaviors and no distinct peak tailings were observed. The salt concentrations at the elution peaks (IR) were in the order of FF-PEI-L680>FF-PEI-L270>Q Sepharose FF, indicating that the elution for the PEI resins needed higher salt concentrations, which was also an appearance of the salt-tolerant feature of the PEI resins. When protein loading amount was increased to the value equivalent to the DBC at 10% breakthrough, the adsorbed BSA could be eluted at lower salt concentrations. The chromatographic study has provided new insights into the practical application of the PEI-based anion exchangers.

Characterization of cross-linked cellulosic ion-exchange adsorbents: 1. Structural properties

The structural characteristics of the HyperCel family of cellulosic ion-exchange materials (Pall Corporation) were assessed using methods to gauge the pore dimensions and the effect of ionic strength on intraparticle architecture. Inverse size exclusion chromatography (ISEC) was applied to the S and STAR AX HyperCel derivatives. The theoretical analysis yielded an average pore radius for each material of about 5nm, with a particularly narrow pore-size distribution. Electron microscopy techniques were used to visualize the particle structure and relate it to macroscopic experimental data. Microscopy of Q and STAR AX HyperCel anion exchangers presented some qualitative differences in pore structure that can be attributed to the derivatization using conventional quaternary ammonium and salt-tolerant ligands, respectively. Finally, the effect of ionic strength was studied through the use of salt breakthrough experiments to determine to what extent Donnan exclusion plays a role in restricting the accessible pore volume for small ions. It was determined that Donnan effects were prevalent at total ionic strengths (TIS) less than 150mM, suggesting the presence of a ligand-containing partitioning volume within the pore space.

Preparation and characterization of keratin-based biocomposite hydrogels prepared by electron beam irradiation

The biocompatible and highly porous keratin-based hydrogels were prepared using electron beam irradiation (EBI). The conditions for keratin-based hydrogel formation were investigated depending on several conditions, including the presence of poly(vinyl alcohol) (PVA), concentration of keratin solution, EBI dose, and poly(ethylene imine) (PEI) additives. The pure keratin (human hair and wool) aqueous solution was not gelled by EBI, while the aqueous keratin solutions blended with PVA were gelled at an EBI dose of more than 90 kGy. Furthermore, in the presence of PEI, the aqueous keratin solution blended with PVA could be gelled at a considerably lower EBI dose, even at 10 kGy. This finding suggests that the PEI additives significantly influence the rate of gelation and that PEIs function as an accelerator during gelation. The resulting keratin-based hydrogels were characterized using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), gel fraction, degree of swelling, gel strength, and kinetics of swelling analyses.