An investigation into the relationship between carrier-based dry powder inhalation performance and formulation cohesive–adhesive force balances

The influence of physical properties and morphology of crystallised lactose on delivery of salbutamol sulphate from dry powder inhalers

The aim of this work was to investigate the mechanistic evaluation of physicochemical properties of new engineered lactose on aerosolisation performance of salbutamol sulphate (SS) delivered from dry powder inhaler (DPI). Different crystallised lactose particles were obtained from binary mixtures of butanol:acetone. The sieved fractions (63-90 μm) of crystallised lactose were characterised in terms of size, shape, flowability, true density and aerosolisation performance (using multiple twin stage impinger (MSLI), Aerolizer(®) inhaler device, and salbutamol sulphate as a model drug). Compared to commercial lactose, crystallised lactose particles were less elongated, covered with fine lactose particles, and had a rougher surface morphology. The crystallised lactose powders had a considerably lower bulk and tap density and poorer flow when compared to commercial lactose. Engineered carrier with better flow showed improved drug content homogeneity, reduced amounts of drug "deposited" on the inhaler device and throat, and a smaller drug aerodynamic diameter upon inhalation. Aerodynamic diameter of salbutamol sulphate increased as lactose aerodynamic diameter decreased (linear, R(2)=0.9191) and/or as fine particle lactose content increased (linear, R(2)=0.8653). Improved drug aerosolisation performance in the case of crystallised lactose particles was attributed to lower drug-carrier adhesion forces due to a rougher surface and higher fine particle content. In conclusion, this work proved that using binary combinations of solvents in crystallisation medium is vital in modification of the physicochemical and micromeritic properties of carriers to achieve a desirable aerosolisation performance from DPI formulations. Among all lactose samples, lactose particles crystallised from pure butanol generated the highest overall DPI formulations desirability.

Improved aerosolization performance of salbutamol sulfate formulated with lactose crystallized from binary mixtures of ethanol-acetone

It has been shown that dry powder inhaler (DPI) formulations typically achieve low fine particle fractions (poor performance). A commonly held theory is that this is due, at least in part, to low levels of detachment of drug from lactose during aerosolization as a result of strong adhesion of drug particles to the carrier surfaces. Therefore, the purpose of the present study is to overcome poor aerosolization performance of DPI formulation by modification of lactose particles. Lactose particles were crystallized by adding solution in water to different ratios of binary mixtures of ethanol-acetone. The results showed that modified lactose particles had exceptional aerosolization performance that makes them superior to commercial lactose particles. Morphology assessment showed that crystallized lactose particles were less elongated, more irregular in shape, and composed of smaller primary lactose particles compared with commercial lactose. Solid-state characterization showed that commercial lactose particles were α-lactose monohydrate, whereas crystallized lactose particles were a mixture of α-lactose monohydrate and β-lactose according to the ratio of ethanol-acetone used during crystallization process. The enhanced performance could be mainly due to rougher surface and/or higher amounts of fines compared with the lactose crystallized from pure ethanol or commercial lactose.

Heterogeneous particle deaggregation and its implication for therapeutic aerosol performance

Aerosolization performance of dry powder blends of drugs for the treatment of asthma or chronic obstructive pulmonary diseases have been reported in three previous articles. In vitro aerosolization was performed at defined shear stresses (0.624-13.143 N/m(2)). Formulations were characterized aerodynamically and powder aerosol deaggregation equations (PADE) and corresponding linear regression analyses for pharmaceutical aerosolization were applied. Particle deaggregation is the result of overcoming fundamental forces acting at the particle interface. A new method, PADE, describing dry powder formulation performance in a shear stress range has been developed which may allow a fundamental understanding of interparticulate and surface forces. The application of PADE predicts performance efficiency and reproducibility and supports rational design of dry powder formulations. The analogy of aerosol performance with surface molecular adsorption has important implications. Expressions describing surface adsorption were intended to allow elucidation of mechanisms involving surface heterogeneity, lateral interaction, and multilayer adsorption of a variety of materials. By using a similar expression for drug aerosolization performance, it is conceivable that an analogous mechanistic approach to the evaluation of particulate systems would be possible.

Engineering of crystalline combination inhalation particles of a long-acting beta2-agonist and a corticosteroid

PURPOSE

Engineering of inhalation particles incorporating, in each individual particle, a combination of a long-acting beta-agonist and a glucocorticosteroid in a pre-determined and constant ratio for delivery via a dry powder inhaler (DPI).

METHODS

Individual crystalline particles containing both the glucocorticosteroid fluticasone propionate (FP) and long-acting beta-agonist salmeterol (SX) were prepared, in a ratio of 10:1, using the solution atomization and crystallization by sonication (SAX) process. Combination drug particles were characterized by particle size, morphology, crystallinity and aerosolisation efficiency using inertial impaction.

RESULTS

Combination drug particles were spherical and crystalline, with a median diameter of 4.68 +/- 0.01 microm. Aerosolisation of formulations containing combination drug particles resulted in greater uniformity in delivery ratios of both actives across all stages of the impactor before and after storage.

CONCLUSIONS

Actives in a pre-determined dose ratio can be crystallised in a single particle using the SAX process.