Fiber-reinforced packable resin composites in Class II cavities

Degradation, fatigue, and failure of resin dental composite materials

The intent of this article is to review the numerous factors that affect the mechanical properties of particle- or fiber-filler-containing indirect dental resin composite materials. The focus will be on the effects of degradation due to aging in different media, mainly water and water and ethanol, cyclic loading, and mixed-mode loading on flexure strength and fracture toughness. Several selected papers will be examined in detail with respect to mixed and cyclic loading, and 3D tomography with multi-axial compression specimens. The main cause of failure, for most dental resin composites, is the breakdown of the resin matrix and/or the interface between the filler and the resin matrix. In clinical studies, it appears that failure in the first 5 years is a restoration issue (technique or material selection); after that time period, failure most often results from secondary decay.

Short glass fiber reinforced restorative composite resin with semi-inter penetrating polymer network matrix

OBJECTIVES

The purpose of this study was to investigate the reinforcing effect of short E-glass fiber fillers on some mechanical properties of dental composite resin with interpenetrating polymer network (IPN)-polymer matrix.

MATERIALS AND METHODS

Experimental composite resin was prepared by mixing short fibers (3mm in length) with a fraction of 22.5 wt% and IPN-resin 22.5 wt% with silane treated silica filler 55 wt% using high speed mixing machine. Test specimens (2 mm x 2 mm x 25 mm) and (9.5 mm x 5.5 mm x 3 mm) were made from the experimental composite (FC) and conventional particulate composite resin (control, Z250, 3M-ESPE). The test specimens (n=6) were either dry stored or water stored (37 degrees C for 30 days) before the mechanical tests. Three-point bending test was carried out according to ISO 10477 and compression loading test was carried out using a steel ball (Ø3.0mm) with speed of 1.0mm/min until fracture. Degree of monomer conversion (DC%) of both composites was determined by FTIR spectrometry. Water sorption and solubility of specimens were also measured. Scanning electron microscopy was used to evaluate the microstructure of the composite.

RESULTS

ANOVA revealed that experimental fiber composite had statistically significantly higher mechanical performance of flexural strength (210 MPa) and compressive load-bearing capacity (1881 N) (p < 0.05) than control composite (111 MPa, 1031 N). Degree of conversion of the FC (59%) and conventional composite (57%) was at the same range.

SIGNIFICANCE

The use of short fiber fillers with IPN-polymer matrix yielded improved mechanical performance compared to conventional restorative composite.

Use of short fiber-reinforced composite with semi-interpenetrating polymer network matrix in fixed partial dentures

OBJECTIVES

The aim of this study was to determine the static load-bearing capacity of fixed partial dentures (FPDs) made of experimental composite resin (FC) with short fiber fillers and interpenetrating polymer network (IPN) polymer matrix.

MATERIALS AND METHODS

Experimental composite FC resin was prepared by mixing short E-glass fibers (3mm in length) of 22.5wt% and IPN-resin 22.5wt% with silane treated silica fillers 55wt%. Four groups of FPDs (3-unit) were fabricated (n=6); Group A: made from commercial composite resin (Sinfony dentin, 3M-ESPE, control), Group B: Sinfony and fiber-reinforced composite (FRC) substructure, Group C: made from FC, Group D: made from FC with 1mm surface layer of Sinfony. The bridges were polymerized with a hand-light curing unit for 40s then post-cured in vacuum curing device (Visio Beta) for 15min before they were statically loaded with speed of 1mm/min until fracture. Failure modes were visually examined. Data were analyzed using ANOVA (p=0.05).

RESULTS

ANOVA revealed that bridges made from experimental fiber composite had statistically significantly higher load-bearing capacity (2171N) (p<0.05) than the control restorations (1482N).

SIGNIFICANCE

Restorations made from short glass fiber containing composite resin with IPN-polymer matrix showed better load bearing capacity than in those made with conventional composites resin and similar with those reinforced with FRC-substructure.