Charge Recombination Control for High Efficiency Quantum Dot Sensitized Solar Cells

Alloying Strategy in Cu-In-Ga-Se Quantum Dots for High Efficiency Quantum Dot Sensitized Solar Cells

I-III-VI₂ group "green" quantum dots (QDs) are attracting increasing attention in photoelectronic conversion applications. Herein, on the basis of the "simultaneous nucleation and growth" approach, Cu-In-Ga-Se (CIGSe) QDs with light harvesting range of about 1000 nm were synthesized and used as sensitizer to construct quantum dot sensitized solar cells (QDSCs). Inductively coupled plasma atomic emission spectrometry (ICP-AES), wild-angle X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) analyses demonstrate that the Ga element was alloyed in the Cu-In-Se (CISe) host. Ultraviolet photoelectron spectroscopy (UPS) and femtosecond (fs) resolution transient absorption (TA) measurement results indicate that the alloying strategy could optimize the electronic structure in the obtained CIGSe QD material, thus matching well with TiO₂ substrate and favoring the photogenerated electron extraction. Open circuit voltage decay (OCVD) and impedance spectroscopy (IS) tests indicate that the intrinsic recombination in CIGSe QDSCs was well suppressed relative to that in CISe QDSCs. As a result, CIGSe based QDSCs with use of titanium mesh supported mesoporous carbon counter electrode exhibited a champion efficiency of 11.49% (J_sc = 25.01 mA/cm², V_oc = 0.740 V, FF = 0.621) under the irradiation of full one sun in comparison with 9.46% for CISe QDSCs.

Sensitizers for Aqueous-Based Solar Cells

Aqueous dye-sensitized solar cells (DSSCs) are attractive due to their sustainability, the use of water as a safe solvent for the redox mediators, and their possible applications in photoelectrochemical water splitting. However, the higher tendency of dye leaching by water and the lower wettability of dye molecules are two major obstacles that need to be tackled for future applications of aqueous DSSCs. Sensitizers designed for aqueous DSSCs are discussed based on their functions, such as modification of the molecular skeleton and the anchoring group for better stability against dye leaching by water, and the incorporation of hydrophilic entities into the dye molecule or the addition of a surfactant to the system to increase the wettability of the dye for more facile dye regeneration. Surface treatment of the photoanode to deter dye leaching or improve the wettability of the dye molecule is also discussed. Redox mediators designed for aqueous DSSCs are also discussed. The review also includes quantum-dot-sensitized solar cells, with a focus on improvements in QD loading and suppression of interfacial charge recombination at the photoanode.

Improving Loading Amount and Performance of Quantum Dot-Sensitized Solar Cells through Metal Salt Solutions Treatment on Photoanode

Increasing QD loading amount on photoanode and suppressing charge recombination are prerequisite for high-efficiency quantum dot-sensitized solar cells (QDSCs). Herein, a facile technique for enhancing the loading amount of QDs on photoanode and therefore improving the photovoltaic performance of the resultant cell devices is developed by pipetting metal salt aqueous solutions on TiO₂ film electrode and then evaporating at elevated temperature. The effect of different metal salt solutions was investigated, and experimental results indicated that the isoelectric point (IEP) of metal ions influenced the loading amount of QDs and consequently the photovoltaic performance of the resultant cell devices. The influence of anions was also investigated, and the results indicated that anions of strong acid made no difference, while acetate anion hampered the performance of solar cells. Infrared spectroscopy confirmed the formation of oxyhydroxides, whose behavior was responsible for QD loading amount and thus solar cell performance. Suppressed charge recombination based on Mg²⁺ treatment under optimal conditions was confirmed by impedance spectroscopy as well as transient photovoltage decay measurement. Combined with high-QD loading amount and retarded charge recombination, the champion cell based on Mg²⁺ treatment exhibited an efficiency of 9.73% (J_sc = 27.28 mA/cm², V_oc = 0.609 V, FF = 0.585) under AM 1.5 G full 1 sun irradiation. The obtained efficiency was one of the best performances for liquid-junction QDSCs, which exhibited a 10% improvement over the untreated cells with the highest efficiency of 8.85%.

Aminoalkanoic Acids as Alternatives to Mercaptoalkanoic Acids for the Linker-Assisted Attachment of Quantum Dots to TiO2

Linear aminoalkanoic acids (AAAs) and mercaptoalkanoic acids (MAAs) were characterized as bifunctional ligands to tether CdSe QDs to nanocrystalline TiO2 thin films and to mediate excited-state electron transfer (ET) from the QDs to TiO2 nanoparticles. The adsorption of 12-aminododecanoic acid (ADA) and 12-mercaptododecanoic acid (ADA) to TiO2 followed the Langmuir adsorption isotherm. Surface adduct formation constants (Kad) were ∼10(4) M(-1); saturation amounts of the ligands per projected surface area of TiO2 (Γ0) were ∼10(-7) mol cm(-2). Both Kad and Γ0 differed by 20% or less for the two linkers. CdSe QDs adhered to ADA- and MDA-functionalized TiO2 films; data were well modeled by the Langmuir adsorption isotherm and Langmuir kinetics. For ADA- and MDA-mediated assembly values of Kad were (1.8 ± 0.4) × 10(6) and (2.4 ± 0.4) × 10(6) M(-1), values of Γ0 were (1.6 ± 0.3) × 10(-9) and (1.2 ± 0.1) × 10(-9) mol cm(-2), and rate constants were (14 ± 5) and (60 ± 20) M(-1) s(-1), respectively. Thus, the thermodynamics and kinetics of linker-assisted assembly were slightly more favorable for MDA than for ADA. Steady-state and time-resolved emission spectroscopy revealed that electrons were transferred from both band-edge and surface states of CdSe QDs to TiO2 with rate constants (ket) of ∼10(7) s(-1). ET was approximately twice as fast through thiol-bearing linker 4-mercaptobutyric acid (MBA) as through amine-bearing linker 4-aminobutyric acid (ABA). Photoexcited QDs transferred holes to adsorbed MBA. In contrast, ABA did not scavenge photogenerated holes from CdSe QDs, which maximized the separation of charges following ET. Additionally, ABA shifted electron-trapping surface states to higher energies, minimizing the loss of potential energy of electrons prior to ET. These trade-offs involving the kinetics and thermodynamics of linker-assisted assembly; the driving force, rate constant, and efficiency of ET; and the extent of photoinduced charge separation can inform the selection bifunctional ligands to tether QDs to surfaces.

Photoinduced electron transfer from quantum dots to TiO2: elucidating the involvement of excitonic and surface states

CdSe QDs transfer electrons from band-edge and surface states to TiO₂; core/shell CdSe/ZnS QDs transfer electrons exclusively from band-edge states.

Recombination control in high-performance quantum dot-sensitized solar cells with a novel TiO2/ZnS/CdS/ZnS heterostructure

A superior photovoltaic performance is obtained with a TiO₂/ZnS/CdS/ZnS heterostructure with controlled recombination.

Optimizing CdS intermediate layer of CdS/CdSe quantum dot-sensitized solar cells to increase light harvesting ability and improve charge separation efficiency

A modified Successive Ionic Layer Adsorption and Reaction (SILAR) technique with the addition of a triethanolamine (TEA) additive into a cationic precursor solution was utilized to optimize the CdS intermediate layer to enhance the performance.