Effect of CaCl2 and KCl on Physiochemical Properties of Model Nutritional Beverages Based on Whey Protein Stabilized Oil-in-Water Emulsions

Production and characterization of oil-in-water emulsions containing droplets stabilized by beta-lactoglobulin-pectin membranes

Oil-in-water emulsions containing droplets stabilized by beta-lactoglobulin (beta-Lg)-pectin membranes were produced using a two-stage process. A primary emulsion containing small droplets (d(32) approximately 0.3 microm) was prepared by homogenizing 10 wt % corn oil with 90 wt % aqueous solution (1 wt % beta-Lg, 5 mM imidazole/acetate buffer, pH 3.0) using a high-pressure valve homogenizer. The primary emulsion was then diluted with pectin solutions to produce secondary emulsions with a range of pectin concentrations (5 wt % corn oil, 0.45 wt % beta-Lg, 5 mM imidazole/acetate buffer, 0-0.22 wt % pectin, pH 3.0). The electrical charge on the droplets in the secondary emulsions decreased from +33 +/- 3 to -19 +/- 1 mV as the pectin concentration was increased from 0 to 0.22 wt %, which indicated that pectin adsorbed to the droplet surfaces. The mean particle diameter of the secondary emulsions was small (d(32) < 1 microm) at relatively low pectin concentrations (<0.04 wt %), but increased dramatically at higher pectin concentrations (e.g., d(32) approximately 13 microm at 0.1 wt % pectin), which was attributed to charge neutralization and bridging flocculation effects. Emulsions with relatively small mean particle diameters (d(32) approximately 1.2 microm at 0.1 wt % pectin) could be produced by disrupting flocs formed in secondary emulsions containing highly negatively charged droplets, for example, by sonication, blending, or homogenization. The particles in these emulsions probably consisted of small flocs containing a number of protein-coated droplets bound together by pectin molecules. These emulsions had good stability to further particle aggregation up to relatively high ionic strengths (< or =500 mM NaCl) and low pH (pH 3). The interfacial engineering technology used in this study could lead to the creation of food emulsions with improved physicochemical properties or stability.

Influence of EDTA and citrate on physicochemical properties of whey protein-stabilized oil-in-water emulsions containing CaCl2

The influence of chelating agents (disodium ethylenediaminetetraacetate (EDTA) and sodium citrate) on the physicochemical properties of whey protein isolate (WPI)-stabilized oil-in-water emulsions containing calcium chloride was determined. The calcium-binding characteristics of EDTA and citrate at 30 degrees C were characterized in aqueous solutions (20 mM Tris buffer, pH 7.0) by isothermal titration calorimetry (ITC). EDTA and citrate both bound calcium ions in a 1:1 ratio, but EDTA had a much higher binding constant. Oil-in-water emulsions (pH 7.0) were prepared containing 6.94% (w/v) soybean oil, 0.35% (w/v) WPI, 0.02% (w/v) sodium azide, 20 mM Tris buffer, 10 mM CaCl(2), and 0-40 mM chelating agent. The particle size, apparent viscosity, creaming stability, free calcium concentration, and particle surface potential of the emulsions were measured. The chelating agents reduced or prevented droplet aggregation in the emulsions. When they were present above a certain concentration (>3.5 mM EDTA or >5 mM citrate), droplet aggregation was prevented. The reduction of aggregation was indicated by decreases in particle size, shear-thinning behavior, apparent viscosity, and creaming. Emulsions containing chelating agents had lower free calcium concentrations and more negatively charged droplets, indicating that the chelating agents improved emulsion stability by binding calcium ions. EDTA could be used at lower concentrations than citrate because of its higher calcium ion binding constant.