Gene expression profile of osseointegration of a hydrophilic compared with a hydrophobic microrough implant surface

Comparison of removal torques between laser-etched and modified sandblasted acid-etched Ti implant surfaces in rabbit tibias

PURPOSE

The purpose of this study was to analyze the effects of two different implant surface treatments on initial bone connection by comparing the Removal Torque Values (RTQs) at 7 and 10 days after chemically modified, sandblasted, large-grit and acid-etched (modSLA), and Laser-etched (LE) Ti implant placements.

MATERIALS AND METHODS

Twenty modSLA and 20 LE implants were installed on the left and right tibias of 20 adult rabbits. RTQs were measured after 7 and 10 days in 10 rabbits each. Scanning electron microscope (SEM) photographs of the two implants were observed by using Quanta FEG 650 from the FEI company (Hillsboro, OR, USA). Analyses of surface elements and components were conducted using energy dispersive spectroscopy (EDS, Horiba, Kyoto, Japan).

RESULTS

The mean RTQs were 12.29 ± 0.830 and 12.19 ± 0.713 Ncm after 7 days (P=.928) and 16.47 ± 1.324 and 16.17 ± 1.165 Ncm after 10 days (P=.867) for LE and modSLA, respectively, indicating no significant inter-group differences. Pore sizes in the LE were 40 µm and consisted of numerous small pores, whereas pore sizes in the modSLA were 5 µm. In the EDS analysis, Ti, O, and C were the only three elements found in the LE surfaces. Na, Ca, Cl, and K were also observed in modSLA, in addition to Ti, O, and C.

CONCLUSION

The implants showed no significant difference in biomechanical bond strength to bone in early-stage osseointegration. LE implant can be considered an excellent surface treatment method in addition to the modSLA implant and can be applied to the early loading of the prosthesis clinically.

Protein expression during early stages of bone regeneration under hydrophobic and hydrophilic titanium domes. A pilot study

BACKGROUND AND OBJECTIVES

There is significant evidence that, during the early stages of osseointegration, moderately rough hydrophilic (SLActive) surfaces can accelerate osteogenesis and increase bone-to-implant contact in comparison to hydrophobic (SLA) surfaces. However, very little is known regarding the molecular mechanisms behind the influence that surface chemistry modifications to increase hydrophilicity determine on bone healing. The aim of this study was to describe for the first time the proteins and related signalling pathways expressed during early osseous healing stages under SLA and SLActive titanium domes for guided bone regeneration.

MATERIAL AND METHODS

One SLA and 1 SLActive dome with an internal diameter of 5.0 mm and a height of 3.0 mm were secured to the parietal bones of nine 6-month-old male New Zealand rabbits. Three animals were randomly euthanized at 4, 7 and 14 days and the newly formed tissues retrieved under the domes were analysed with liquid chromatography-mass spectrometry/mass spectrometry. STRING and KEGG databases were applied for Gene Ontology and pathway analyses.

RESULTS

A different modulation of several pathways was detected between the 2 groups at all healing times. The main differences in the osseous healing response associated to the 2 surfaces were related to pathways involved in regulating the inflammatory response, differentiation of osteoblast precursors and skeletogenesis. At day 7, the highest number of proteins and the highest cellular activity were observed in both groups, although a more complex and articulated proteome in terms of cellular metabolism and signal transduction was observed in SLActive samples.

CONCLUSION

This is the first study describing the proteome expressed during early healing stages of guided bone regeneration and osseointegration. A combination of enhanced early osteogenic response and reduced inflammatory response were suggested for the hydrophilic group. Future studies are needed to corroborate these findings and explore the molecular effects of different titanium surfaces on the cascade of events taking place during bone formation.

Surface characteristics of dental implants: A review

OBJECTIVES

During the last decades, several changes of paradigm have modified our view on how biomaterials' surface characteristics influence the bioresponse. After becoming aware of the role of a certain microroughness for improved cellular contact and osseointegration of dental titanium implants, the likewise important role of surface energy and wettability was increasingly strengthened. Very recently, synergistic effects of nanoscaled topographical features and hydrophilicity at the implant/bone interface have been reported.

METHODS

Questions arise about which surface roughness and wetting data are capable to predict the bioresponse and, ultimately, the clinical performance. Current methods and approaches applied for topographical, wetting and surface energetic analyses are highlighted. Current knowledge of possible mechanisms explaining the influence of roughness and hydrophilicity at the biological interface is presented.

RESULTS

Most marketed and experimental surfaces are based on commonly available additive or subtractive surface modifying methods such as blasting, etching or anodizing. Different height, spatial, hybrid and functional roughness parameters have been identified as possible candidates able to predict the outcome at hard and soft tissue interfaces. Likewise, hydrophilic implants have been proven to improve the initial blood contact, to support the wound healing and thereby accelerating the osseointegration.

SIGNIFICANCE

There is clear relevance for the influence of topographical and wetting characteristics on a macromolecular and cellular level at endosseous implant/biosystem interfaces. However, we are still far away from designing sophisticated implant surfaces with the best possible, selective functionality for each specific tissue or cavity interface. Firstly, because our knowledge of the respective surface related reactions is at best fragmentary. Secondly, because manufacturing of multi-scaled complex surfaces including distinct nanotopographies, wetting properties, and stable cleanliness is still a technical challenge and far away from being reproducibly transferred to implant surfaces.

Accelerated Healing Period with Hydrophilic Implant Placed in Sheep Tibia

Abstract The objective of this study was to evaluate the early osseointegration of two different implants surfaces, a sandblasted and acid-etched surface (TN) compared with same geometry and surface roughness modified to be hydrophilic/wettable by conditioning in an isotonic solution of 0.9% sodium-chloride (TA) through histological and histomorphometric analysis after sheep tibia implantation. Forty dental implants, divided in two groups (TN and TA) were placed in the left tibia of twenty healthy, skeletally mature Santa Ines sheep (n=5/experimental period). After 7, 14, 21 and 28 days post-implantation, the samples were removed and the sheep were kept alive. Analysis of resin sections (30 μm) allowed the quantification of bone area (BA) and bone-to-implant contact (BIC). TA group presented nearly 50% increase in BA at 14 days (p<0.001, ANOVA - Tukey’s post test) compared with 7 days. The TA presented higher values than the TN for BA and BIC at 14, 21, and 28 days after placement, stabilizing bone healing. TA hydrophilic surface promoted early osseointegration at 14 and 21 days compared to TN, accelerating bone healing period post-implant placement in sheep tibia.

The role of immediate provisional restorations on implants with a hydrophilic surface: A randomised, single-blind controlled clinical trial

OBJECTIVES

To compare the radiographic bone changes, clinical parameters and aesthetic outcomes of immediately provisionalised and conventionally restored implants at 12- and 24-months post-implant placement.

MATERIAL AND METHODS

In 24 patients, 24 bone level implants with a hydrophilic (SLActive) surface were placed in healed sites and they were either immediately provisionalised with a non-occluding temporary crown (test group) or left without a crown (control group). In both groups, the definitive restoration was placed 16 weeks after implant placement. Clinical and radiographic parameters were calculated at 12- and 24-months post-implant placement, together with implant success/survival rates according to three different sets of criteria. The aesthetic outcome was evaluated through the Papilla Fill Index and the Pink Aesthetic Score.

RESULTS

The mean marginal bone loss at 1 year was -0.73 mm (SD 0.83 mm) in the test group and -0.22 mm (SD 0.46 mm) in the control group (p > .05). Whilst 100% survival rate and positive aesthetic outcomes were recorded in both groups, three patients of the test group did not fulfil all success criteria.

CONCLUSIONS

Immediate provisionalisation may represent a viable option for the replacement of single missing teeth, with radiographic, clinical and aesthetic results comparable to those of conventionally loaded implants at 2 years of follow-up.

Clinical, radiological, and gene expression analyses in smokers and non-smokers, Part 2: RCT on the late healing phase of osseointegration

BACKGROUND

The mechanisms behind the impact of smoking on osseointegration are not fully understood.

PURPOSE

To investigate the initial clinical and molecular course of osseointegration of different implants in smokers and non-smokers in a randomized controlled trial (RCT).

MATERIALS AND METHODS

Smoking (n = 16) and non-smoking (n = 16) patients received 3 implant types: machined, oxidized, and laser-modified surfaces. Baseline bone biopsies were retrieved from the implant sites. After 60 and 90 days, the pain score, implant stability quotient (ISQ), and peri-implant crevicular fluid (PICF) gene expression were analyzed. Furthermore, radiological and clinical assessments were made at 90 days.

RESULTS

At 90 days, no pain was reported, irrespective of smoking habit. A higher ISQ was found in smokers compared with non-smokers. Marginal bone loss (MBL) was greater in smokers than in non-smokers. The comparison of implant surfaces revealed greater MBL exclusively at the machined implants in smokers. At 90 days in smokers, the PICF around machined implants revealed a higher expression of the proinflammatory cytokine, interleukin-6 (IL-6), and a lower expression of the osteogenic gene, osteocalcin (OC), compared with the PICF around modified implants. Furthermore, OC expression was lower at machined implants in smokers compared with machined implants in non-smokers. After adjustment for age and implant location (maxilla/mandible), multivariate regression revealed the following predictors of MBL: smoking, bleeding on probing at 90 days, hypoxia-inducible factor 1 alpha (HIF-1α) expression at baseline and IL-6 expression in PICF at 90 days.

CONCLUSIONS

During the early phase of osseointegration, non-smokers and smokers present a similar, high implant survival. In contrast, smokers present a greater MBL, particularly at machined implants. HIF-1α baseline expression in the recipient bone and IL-6 expression in PICF cells are important molecular determinants for MBL after 90 days. It is concluded that smoking has an early effect on osseointegration, which is dependent on the implant surface properties and the local host response.

Effect of enamel matrix derivative on the angiogenic behaviors of human umbilical vein endothelial cells on different titanium surfaces

Angiogenesis play a crucial role in the regeneration of hard and soft tissue around dental titanium (Ti) implant. Enamel matrix derivative (EMD) promotes tissue regeneration and stimulates angiogenesis but its effect on the angiogenesis on Ti surfaces was never investigated. The effect of EMD on the angiogenic activity of endothelial cells cultured on pre-treated smooth Ti (PT), acidetched (A), coarse-grit blasted and acid-etched (SLA) surfaces and tissue culture plastic (TCP) in the presence or absence of EMD was investigated. EMD inhibited the proliferation/viability of human umbilical vein endothelial cells (HUVECs) growing on A and SLA Ti surfaces. EMD induced an increase in the expression of all these genes in HUVECs grown on SLA surface but not on other surfaces. Summarizing, our data show that EMD influences proliferation and expression of angiogenesis associated gene in HUVECs grown on moderately rough SLA surfaces, suggesting that EMD might promote angiogenesis following implantation.

In vitro and in vivo characterization of anodised zirconium as a potential material for biomedical applications

In vitro studies offer the insights for the understanding of the mechanisms at the tissue-implant interface that will provide an effective functioning in vivo. The good biocompatibility of zirconium makes a good candidate for biomedical applications and the attractive in vivo performance is mainly due to the presence of a protective oxide layer. The aim of this study is to evaluate by in vitro and in vivo approach, the influence of surface modification achieved by anodisation at 30 and 60V on zirconium implants on the first steps of the osseointegration process. In this study cell attachment, proliferation and morphology of mouse myoblast C2C12-GFP and in mouse osteoprogenitor MC3T3-E1 cells was evaluated. Also, together with the immune system response, osteoclast differentiation and morphology with RAW 264.7 murine cell line were analysed. It was found that anodisation treatment at 60V enhanced cell spreading and the osteoblastic and osteoclastic cells morphology, showing a strong dependence on the surface characteristics. In vivo tests were performed in a rat femur osteotomy model. Dynamical and static histological and histomorphometric analyses were developed 15 and 30days after surgery. Newly formed bone around Zr60V implants showed a continuous newly compact and homogeneous bone just 15 after surgery, as judged by the enhanced thickness and mineralization rate. The results indicate that anodising treatment at 60V could be an effective improvement in the osseointegration of zirconium by stimulating adhesion, proliferation, morphology, new bone thickness and bone mineral apposition, making zirconium an emerging candidate material for biomedical applications.

Temporal sequence of hard and soft tissue healing around titanium dental implants

The objective of the present review was to summarize the evidence available on the temporal sequence of hard and soft tissue healing around titanium dental implants in animal models and in humans. A search was undertaken to find animal and human studies reporting on the temporal dynamics of hard and soft tissue integration of titanium dental implants. Moreover, the influence of implant surface roughness and chemistry on the molecular mechanisms associated with osseointegration was also investigated. The findings indicated that the integration of titanium dental implants into hard and soft tissue represents the result of a complex cascade of biological events initiated by the surgical intervention. Implant placement into alveolar bone induces a cascade of healing events starting with clot formation and continuing with the maturation of bone in contact with the implant surface. From a genetic point of view, osseointegration is associated with a decrease in inflammation and an increase in osteogenesis-, angiogenesis- and neurogenesis-associated gene expression during the early stages of wound healing. The attachment and maturation of the soft tissue complex (i.e. epithelium and connective tissue) to implants becomes established 6-8 weeks following surgery. Based on the findings of the present review it can be concluded that improved understanding of the mechanisms associated with osseointegration will provide leads and targets for strategies aimed at enhancing the clinical performance of titanium dental implants.

The effects of implant topography on osseointegration under estrogen deficiency induced osteoporotic conditions: Histomorphometric, transcriptional and ultrastructural analysis

Compromised bone quality and/or healing in osteoporosis are recognised risk factors for impaired dental implant osseointegration. This study examined the effects of (1) experimentally induced osteoporosis on titanium implant osseointegration and (2) the effect of modified implant surface topography on osseointegration under osteoporosis-like conditions. Machined and micro-roughened surface implants were placed into the maxillary first molar root socket of 64 ovariectomised and sham-operated Sprague-Dawley rats. Subsequent histological and SEM observations showed tissue maturation on the micro-rough surfaced implants in ovariectomised animals as early as 3days post-implantation. The degree of osseointegration was also significantly higher around the micro-rough implants in ovariectomised animals after 14days of healing although by day 28, similar levels of osseointegration were found for all test groups. The micro-rough implants significantly increased the early (day 3) gene expression of alkaline phosphatase, osteocalcin, receptor activator of nuclear factor kappa-B ligand and dentin matrix protein 1 in implant adherent cells. By day 7, the expression of inflammatory genes decreased while the expression of the osteogenic markers increased further although there were few statistically significant differences between the micro-rough and machined surfaces. Osteocyte morphology was also affected by estrogen deficiency with the size of the cells being reduced in trabecular bone. In conclusion, estrogen deficiency induced osteoporotic conditions negatively influenced the early osseointegration of machined implants while micro-rough implants compensated for these deleterious effects by enhancing osteogenic cell differentiation on the implant surface.

STATEMENT OF SIGNIFICANCE

Lower bone density, poor bone quality and osseous microstructural changes are all features characteristic of osteoporosis that may impair the osseointegration of dental implants. Using a clinically relevant trabecular bone model in the rat maxilla, we demonstrated histologically that the negative effects of surgically-induced osteoporosis on osseointegration could be ameliorated by the biomaterial's surface topography. Furthermore, gene expression analysis suggests this may be a result of enhanced osteogenic cell differentiation on the implant surface.

Dental implants in patients affected by systemic diseases

Several systemic diseases (and relative medications) have been reported to impair or in some cases complicate dental implant surgery. In broader terms, when dealing with patients suffering from systemic diseases, the monitoring of the medical condition and of the related post-operative complications is of great importance in order to avoid risks which could jeopardise the health of the patient. In this review, the available evidence on implant survival/success, as well as relevant surgical recommendations in patients affected by systemic diseases, are evaluated and when possible, practical suggestions for the clinician are provided.

Microarray gene expression during early healing of GBR-treated calvarial critical size defects

OBJECTIVES

To investigate the gene expression and molecular pathways implicated in the regulation of the osseous healing process following guided bone regeneration (GBR).

MATERIAL AND METHODS

Six 6-month-old Wistar male rats were used. Standardized 5-mm critical size defects were created in the parietal bones of each animal and treated with an extracranial and intracranial ePTFE membrane, according to the GBR principle. Three animals were randomly sacrificed after 7 and 15 days of healing. Total RNA was extracted from each sample and prepared for gene expression analysis. RNA quality and quantity were assessed, followed by hybridization of the cRNA to Affymetrix GeneChip Rat Genome 230 2.0 Arrays. The Affymetrix data were processed, and first-order analysis, quality control and statistical analysis were performed. Biological interpretation was performed via pathway and Gene Ontology (GO) analysis.

RESULTS

Between the 7- and 15-day samples, 538 genes were differently regulated. At day 7, inflammatory and immune responses were clearly upregulated. In addition, GO terms related to angiogenesis and cell cycle regulation were overexpressed. At day 15, a more complex cellular activity and cell metabolism were evident. The bone formation processes were significantly overexpressed, with several genes encoding growth factors, enzyme activity, and extracellular matrix formation found as upregulated. Remarkably, a negative regulation of Wnt signalling pathway was observed at 15 days.

DISCUSSION

The gene expression profile of the cells participating in osseous formation varied depending on the healing stage. A number of candidate genes that seem differentially expressed during early stages of intramembranous bone regeneration was suggested.

The role of angiogenesis in implant dentistry part I: Review of titanium alloys, surface characteristics and treatments

Background

Angiogenesis plays an important role in osseointegration process by contributing to inflammatory and regenerative phases of surrounding alveolar bone. The present review evaluated the effect of titanium alloys and their surface characteristics including: surface topography (macro, micro, and nano), surface wettability/energy, surface hydrophilicity or hydrophobicity, surface charge, and surface treatments of dental implants on angiogenesis events, which occur during osseointegration period.

Material and Methods

An electronic search was performed in PubMed, MEDLINE, and EMBASE databases via OVID using the keywords mentioned in the PubMed and MeSH headings regarding the role of angiogenesis in implant dentistry from January 2000-April 2014.

Results

Of the 2,691 articles identified in our initial search results, only 30 met the inclusion criteria set for this review. The hydrophilicity and topography of dental implants are the most important and effective surface characteristics in angiogenesis and osteogenesis processes. The surface treatments or modifications of dental implants are mainly directed through the enhancement of biological activity and functionalization in order to promote osteogenesis and angiogenesis, and accelerate the osseointegration procedure.

Conclusions

Angiogenesis is of great importance in implant dentistry in a manner that most of the surface characteristics and treatments of dental implants are directed toward creating a more pro-angiogenic surface on dental implants. A number of studies discussed the effect of titanium alloys, dental implant surface characteristic and treatments on agiogenesis process. However, clinical trials and in-vivo studies delineating the mechanisms of dental implants, and their surface characteristics or treatments, action in angiogenesis processes are lagging.

Key words:Angiogenesis, dental implant, osseointergration.

The response of osteoblastic MC3T3-E1 cells to micro- and nano-textured, hydrophilic and bioactive titanium surfaces

The aim of the present work was to investigate the morphology and activity of the murine osteoblastic cell line MC3T3 on control smooth (Machined), commercially available rough (ZT) titanium discs, and on titanium samples obtained by modifying the ZT treatment protocol, and herein labelled as ZTF, ZTM and ZTFM. Cells were evaluated at SEM and immunofluorescence for morphology and cell-to-cell interactions and by MTT assay and real time PCR for cell growth and function. Microscopy showed that ZT modified protocols could differently affect cell shape and distribution. All the tested surfaces showed good biocompatibility by viability assay. However, cells on smoother surfaces appeared to express higher levels of transcript for Collagen 1a1, the main component of extracellular matrix, by real time PCR. Expression of the early differentiation marker Alkaline Phosphatase was higher on ZTF surfaces and ZTM enhanced the expression of later osteoblastic markers Osteoprotegerin and Osteocalcin. Noteworthy, the expression of Connexin 43, a component of cell-to-cell contacts and hemichannels, followed a similar pattern to differentiation marker genes and was higher in cells on ZTM surfaces, consistently with the microscopic observation of cell clusters. Taken together, this data showed that ZTF and ZTM treatment protocols appeared to improve the basal sand-blasting/acid-etching ZT procedure with ZTM surfaces promoting the most mature stage of differentiation.

A strontium-incorporated nanoporous titanium implant surface for rapid osseointegration

Rapid osseointegration of dental implants will shorten the period of treatment and enhance the comfort of patients. Due to the vital role of angiogenesis played during bone development and regeneration, it might be feasible to promote rapid osseointegration by modifying the implant surface to gain a combined angiogenesis/osteogenesis inducing capacity. In this study, a novel coating (MAO-Sr) with strontium-incorporated nanoporous structures on titanium implants was generated via a new micro-arc oxidation, in an attempt to induce angiogenesis and osteogenesis to enhance rapid osseointegration. In vitro, the nanoporous structure significantly enhanced the initial adhesion of canine BMSCs. More importantly, sustained release of strontium ions also displayed a stronger effect on the BMSCs in facilitating their osteogenic differentiation and promoting the angiogenic growth factor secretion to recruit endothelial cells and promote blood vessel formation. Advanced mechanism analyses indicated that MAPK/Erk and PI3K/Akt signaling pathways were involved in these effects of the MAO-Sr coating. Finally, in the canine dental implantation study, the MAO-Sr coating induced faster bone formation within the initial six weeks and the osseointegration effect was comparable to that of the commercially available ITI implants. These results suggest that the MAO-Sr coating has the potential for future use in dental implants.

New Ti-Alloys and Surface Modifications to Improve the Mechanical Properties and the Biological Response to Orthopedic and Dental Implants: A Review

Titanium implants are widely used in the orthopedic and dentistry fields for many decades, for joint arthroplasties, spinal and maxillofacial reconstructions, and dental prostheses. However, despite the quite satisfactory survival rates failures still exist. New Ti-alloys and surface treatments have been developed, in an attempt to overcome those failures. This review provides information about new Ti-alloys that provide better mechanical properties to the implants, such as superelasticity, mechanical strength, and corrosion resistance. Furthermore, in vitro and in vivo studies, which investigate the biocompatibility and cytotoxicity of these new biomaterials, are introduced. In addition, data regarding the bioactivity of new surface treatments and surface topographies on Ti-implants is provided. The aim of this paper is to discuss the current trends, advantages, and disadvantages of new titanium-based biomaterials, fabricated to enhance the quality of life of many patients around the world.

Early osseointegration driven by the surface chemistry and wettability of dental implants

Objective

The objective of this study was to investigate the impact of two different commercially available dental implants on osseointegration.

The surfaces were

sandblasting and acid etching (Group 1) and sandblasting and acid etching, then maintained in an isotonic solution of 0.9% sodium chloride (Group 2).

Material and Methods

X-ray photoelectron spectroscopy (XPS) was employed for surface chemistry analysis. Surface morphology and topography was investigated by scanning electron microscopy (SEM) and confocal microscopy (CM), respectively. Contact angle analysis (CAA) was employed for wetting evaluation. Bone-implant-contact (BIC) and bone area fraction occupied (BAFO) analysis were performed on thin sections (30 μm) 14 and 28 days after the installation of 10 implants from each group (n=20) in rabbits’ tibias. Statistical analysis was performed by ANOVA at the 95% level of significance considering implantation time and implant surface as independent variables.

Results

Group 2 showed 3-fold less carbon on the surface and a markedly enhanced hydrophilicity compared to Group 1 but a similar surface roughness (p>0.05). BIC and BAFO levels in Group 2 at 14 days were similar to those in Group 1 at 28 days. After 28 days of installation, BIC and BAFO measurements of Group 2 were approximately 1.5-fold greater than in Group 1 (p<0.05).

Conclusion

The surface chemistry and wettability implants of Group 2 accelerate osseointegration and increase the area of the bone-to-implant interface when compared to those of Group 1.

Osseointegration of titanium implants with SLAffinity treatment: a histological and biomechanical study in miniature pigs

PURPOSE

Electrochemical oxidation following sandblasting and acid-etching (SLA) treatment has received interest as a surface modification procedure for titanium (Ti) implants (denoted as an SLAffinity surface); however, little information is available on its impacts on the in vivo performance of SLAffinity-Ti implants. The present study evaluated the osseointegration and biomechanical bone-tissue response to SLAffinity-Ti implants with micro- and nanoporous oxide layers.

MATERIALS AND METHODS

The interaction between blood and the tested implants was examined. In total, 144 implants with the following surfaces were used: a standard machined (M-Ti), an SLA-Ti, and an SLAffinity-Ti surface. For each animal, four implants (one M-Ti, one SLA-Ti, and two SLAffinity-Ti) were inserted into the mandibular canine-premolar area for histomorphometric observations and another four implants were inserted into the flat surface on the anteromedial aspect of the rear tibia for removal torque (RT) tests. After 2, 4, and 8 weeks of implantation, histomorphometric and RT tests were conducted.

RESULTS

Interactions between blood and implants were better for implants with the SLAffinity-Ti surface. RT tests showed a significant improvement in fixation strength for SLAffinity-Ti implants (84.5 ± 8.7 N-cm) after 8 weeks compared to M-Ti (62.95 ± 11.5 N-cm) and SLAffinity-Ti (76.1 ± 6.6 N-cm) implants. A histological evaluation showed that osseous integration had occurred with all implants after 8 weeks. SLAffinity-Ti implants exhibited 28.5 ± 6.2 % bone-to-implant contact (BIC) at 2 weeks and 84.3 ± 8.1 % at 8 weeks. M-Ti implants exhibited BIC levels of 17.0 ± 5.4 and 76.5 ± 6.3 %, whereas SLA-Ti implants exhibited BIC levels of 28.5 ± 6.2 and 81.1 ± 8.4 % at corresponding time intervals. In terms of the peri-implant bone area (BA), values for SLAffinity-Ti implants ranged from 29.5 ± 4.1 to 88.3 ± 3.0 %. For M-Ti implants, values ranged from 20.3 ± 5.5 to 81.7 ± 4.2 %. For SLA-Ti implants, values ranged from 23.0 ± 3.5 to 84.0 ± 3.6 %.

CONCLUSIONS

Electrochemical oxidation increased the oxide layers and improved the blood interaction with SLAffinity-Ti implants, resulting in significantly higher bone apposition with the SLAffinity-Ti implants after 2 and 8 weeks of healing. An increase in resistance for the RT of SLAffinity-Ti implants over the 8-week healing period was also observed.

CLINICAL RELEVANCE

The use of SLAffinity-Ti implants has potential for improvement of early osseointegration.

A Novel Investigation of the Formation of Titanium Oxide Nanotubes on Thermally Formed Oxide of Ti-6Al-4V

Traditionally, titanium oxide (TiO2) nanotubes (TNTs) are anodized on Ti-6Al-4V alloy (Ti-V) surfaces with native TiO2 (amorphous TiO2); subsequent heat treatment of anodized surfaces has been observed to enhance cellular response. As-is bulk Ti-V, however, is often subjected to heat treatment, such as thermal oxidation (TO), to improve its mechanical properties. Thermal oxidation treatment of Ti-V at temperatures greater than 200°C and 400°C initiates the formation of anatase and rutile TiO2, respectively, which can affect TNT formation. This study aims at understanding the TNT formation mechanism on Ti-V surfaces with TO-formed TiO2 compared with that on as-is Ti-V surfaces with native oxide. Thermal oxidation–formed TiO2 can affect TNT formation and surface wettability because TO-formed TiO2 is expected to be part of the TNT structure. Surface characterization was carried out with field emission scanning electron microscopy, energy dispersive x-ray spectroscopy, water contact angle measurements, and white light interferometry. The TNTs were formed on control and 300°C and 600°C TO-treated Ti-V samples, and significant differences in TNT lengths and surface morphology were observed. No difference in elemental composition was found. Thermal oxidation and TO/anodization treatments produced hydrophilic surfaces, while hydrophobic behavior was observed over time (aging) for all samples. Reduced hydrophobic behavior was observed for TO/anodized samples when compared with control, control/anodized, and TO-treated samples. A method for improved surface wettability and TNT morphology is therefore discussed for possible applications in effective osseointegration of dental and orthopedic implants.

Wound models for periodontal and bone regeneration: the role of biologic research

The ultimate goals of periodontal therapy remain the complete regeneration of those periodontal tissues lost to the destructive inflammatory-immune response, or to trauma, with tissues that possess the same structure and function, and the re-establishment of a sustainable health-promoting biofilm from one characterized by dysbiosis. This volume of Periodontology 2000 discusses the multiple facets of a transition from therapeutic empiricism during the late 1960s, toward regenerative therapies, which is founded on a clearer understanding of the biophysiology of normal structure and function. This introductory article provides an overview on the requirements of appropriate in vitro laboratory models (e.g. cell culture), of preclinical (i.e. animal) models and of human studies for periodontal wound and bone repair. Laboratory studies may provide valuable fundamental insights into basic mechanisms involved in wound repair and regeneration but also suffer from a unidimensional and simplistic approach that does not account for the complexities of the in vivo situation, in which multiple cell types and interactions all contribute to definitive outcomes. Therefore, such laboratory studies require validatory research, employing preclinical models specifically designed to demonstrate proof-of-concept efficacy, preliminary safety and adaptation to human disease scenarios. Small animal models provide the most economic and logistically feasible preliminary approaches but the outcomes do not necessarily translate to larger animal or human models. The advantages and limitations of all periodontal-regeneration models need to be carefully considered when planning investigations to ensure that the optimal design is adopted to answer the specific research question posed. Future challenges lie in the areas of stem cell research, scaffold designs, cell delivery and choice of growth factors, along with research to ensure appropriate gingival coverage in order to prevent gingival recession during the healing phase.

Genomic analyses of early peri-implant bone healing in humans: a systematic review

Objective

The objective of the study was to systematically review the literature for studies reporting gene expression analyses (GEA) of the biological processes involved in early human peri-implant bone healing.

Methods

Electronic databases (MEDLINE, EMBASE) were searched in duplicate. Controlled and uncontrolled studies reporting GEA of human peri-implant tissues - including ≥5 patients and ≥2 time points - during the first 4 weeks of healing were eligible for inclusion. Methodological quality and risk of bias were also assessed.

Results

Four exploratory studies were included in reporting GEA of either tissues attached to SLA or SLActive implants after 4 to 14 days or cells attached to TiOBlast or Osseospeed implants after 3 to 7 days. A total of 111 implants from 43 patients were analyzed using validated array methods; however, considerable heterogeneity and risk of bias were detected. A consistent overall pattern of gene expression was observed; genes representing an immuno-inflammatory response were overexpressed at days 3 to 4, followed by genes representing osteogenic processes at day 7. Genes representing bone remodeling, angiogenesis, and neurogenesis were expressed concomitantly with osteogenesis. Several regulators of these processes, such as cytokines, growth factors, transcription factors, and signaling pathways, were identified. Implant surface properties seemed to influence the healing processes at various stages via differential gene expression.

Conclusion

Limited evidence from gene expression studies in humans indicates that osteogenic processes commence within the first post-operative week and they appear influenced at various stages by implant surface properties.

Oxidized Titanium Implants Enhance Osseointegration via Mechanisms Involving RANK/RANKL/OPG Regulation

BACKGROUND

The role of implant surface properties for bone formation and bone remodeling, that is, the major events during osseointegration, are incompletely understood.

PURPOSE

This experimental study aimed to investigate the relation between molecular and morphological patterns at the bone interface for machined and oxidized implants.

MATERIALS AND METHODS

Machined and anodically oxidized titanium implants were inserted in rat tibiae. The implants and surrounding tissue were retrieved at 1, 3, 6, 14, or 28 days for gene expression, histology, histomorphometry, backscatter scanning electron microscopy, and transmission electron microscopy.

RESULTS

Compared with machined-surface implants, a higher degree of mineralized bone was found in contact with the oxidized-surface implants. After 3 days, cells adherent to the oxidized implants demonstrated a markedly higher expression of receptor activator of nuclear factor kappa-B (RANK), receptor activator of nuclear factor kappa-B ligand (RANKL), and osteoprotegerin (OPG). Whereas the OPG expression was higher at the machined implants at 6, 14, and 28 days, a higher RANKL/OPG ratio was detected at the oxidized implants. Between 3 and 14 days, both implants demonstrated a temporal increase in RANKL/OPG, corresponding to the remodeling phase at the bone-implant interface. For both implant types, the RANKL/OPG ratio sharply decreased to a low level after 28 days.

CONCLUSIONS

The present results show that oxidized implants rapidly promote a high degree of mineralized bone apposition to the surface. As determined by the gene expression data, the mechanisms involve an early induction of osteoclastic differentiation and subsequently more intensive bone remodeling, which accelerates the maturation of the bone-implant interface. The present study suggests that the RANKL/OPG ratio is a sensitive indicator for monitoring the remodeling process during osseointegration.

Osteoblast maturation on microtextured titanium involves paracrine regulation of bone morphogenetic protein signaling

Osteoblasts are sensitive to surface microtopography and chemistry. Osteoblast differentiation and maturation are higher in vitro and bone formation and osseointegration enhanced in vivo on microstructured titanium (Ti) compared to smooth surfaces. Cells increased BMP2 expression on microtextured Ti alloy, suggesting a paracrine role in regulating osteoblast maturation. However, recent studies show that exogenous BMP2 inhibits osteoblast production of anti-inflammatory cytokines and osteocalcin, indicating that control of BMP-signaling may be involved. This study examined whether cells modulate BMP ligands, receptors, and inhibitors during osteoblast maturation on Ti, specifically focusing on the roles of BMP2 and Noggin (NOG). mRNA and protein for BMP2, BMP4, and BMP7 and receptors BMPR1A, BMPR1B, and BMPR2, and BMP inhibitors were upregulated on microtextured surfaces in comparison to smooth surfaces. Maturation on microstructured Ti was slightly enhanced with exogenous BMP2 while NOG addition inhibited osteoblast maturation. Cells with NOG knocked down significantly increased osteoblast maturation. These results demonstrate that BMP-related molecules are controlled during osteoblast maturation on microstructured Ti surfaces and that endogenous NOG is an important regulator of the process. Modifying paracrine BMP signaling may yield more robust bone formation than application of exogenous BMPs.

Bioactive supramolecular peptide nanofibers for regenerative medicine

Recent advances in understanding of cell-matrix interactions and the role of the extracellular matrix (ECM) in regulation of cellular behavior have created new perspectives for regenerative medicine. Supramolecular peptide nanofiber systems have been used as synthetic scaffolds in regenerative medicine applications due to their tailorable properties and ability to mimic ECM proteins. Through designed bioactive epitopes, peptide nanofiber systems provide biomolecular recognition sites that can trigger specific interactions with cell surface receptors. The present Review covers structural and biochemical properties of the self-assembled peptide nanofibers for tissue regeneration, and highlights studies that investigate the ability of ECM mimetic peptides to alter cellular behavior including cell adhesion, proliferation, and/or differentiation.

Gene expression profiling of peri-implant healing of PLGA-Li+ implants suggests an activated Wnt signaling pathway in vivo

Bone development and regeneration is associated with the Wnt signaling pathway that, according to literature, can be modulated by lithium ions (Li+). The aim of this study was to evaluate the gene expression profile during peri-implant healing of poly(lactic-co-glycolic acid) (PLGA) implants with incorporated Li+, while PLGA without Li+ was used as control, and a special attention was then paid to the Wnt signaling pathway. The implants were inserted in rat tibia for 7 or 28 days and the gene expression profile was investigated using a genome-wide microarray analysis. The results were verified by qPCR and immunohistochemistry. Histomorphometry was used to evaluate the possible effect of Li+ on bone regeneration. The microarray analysis revealed a large number of significantly differentially regulated genes over time within the two implant groups. The Wnt signaling pathway was significantly affected by Li+, with approximately 34% of all Wnt-related markers regulated over time, compared to 22% for non-Li+ containing (control; Ctrl) implants. Functional cluster analysis indicated skeletal system morphogenesis, cartilage development and condensation as related to Li+. The downstream Wnt target gene, FOSL1, and the extracellular protein-encoding gene, ASPN, were significantly upregulated by Li+ compared with Ctrl. The presence of β-catenin, FOSL1 and ASPN positive cells was confirmed around implants of both groups. Interestingly, a significantly reduced bone area was observed over time around both implant groups. The presence of periostin and calcitonin receptor-positive cells was observed at both time points. This study is to the best of the authors' knowledge the first report evaluating the effect of a local release of Li+ from PLGA at the fracture site. The present study shows that during the current time frame and with the present dose of Li+ in PLGA implants, Li+ is not an enhancer of early bone growth, although it affects the Wnt signaling pathway.

The Effect of Platelet Proteins Released in Response to Titanium Implant Surfaces on Macrophage Pro-Inflammatory Cytokine Gene Expression

BACKGROUND AND PURPOSE

Platelets are one of the earliest cell types to interact with surgically inserted titanium implants. This in vitro study investigated the effect of titanium surface-induced platelet releasate on macrophage cytokine gene expression.

MATERIALS AND METHODS

To mimic the in vivo temporal sequence of platelet arrival and protein production at the implant surface and the subsequent effect of these proteins on mediators of the immune response, the levels of platelet attachment and activation in response to culture on smooth polished, sandblasted and acid-etched (SLA), and hydrophilic-modified SLA (modSLA) titanium surfaces were first determined by microscopy and protein assay. The subsequent effect of the platelet-released proteins on human THP-1 macrophage cytokine gene expression was determined by polymerase chain reaction array after 1 and 3 days of macrophage culture on the titanium surfaces in platelet-releasate conditioned media.

RESULTS

Platelet attachment was surface dependent with decreased attachment observed on the hydrophilic (modSLA) surface. The platelet releasate, when considered independently of the surface effect, elicited an overall pro-inflammatory response in macrophage cytokine gene expression, that is, the expression of typical pro-inflammatory cytokine genes such as TNF, IL1a, IL1b, and CCL1 was significantly up-regulated whereas the expression of anti-inflammatory cytokine genes such as IL10, CxCL12, and CxCL13 was significantly down-regulated. However, following platelet exposure to different surface modifications, the platelet releasate significantly attenuated the macrophage pro-inflammatory response to microrough (SLA) titanium and hastened an anti-inflammatory response to hydrophilic (modSLA) titanium.

CONCLUSIONS

Theses results demonstrate that titanium surface topography and chemistry are able to influence the proteomic profile released by platelets, which can subsequently influence macrophage pro-inflammatory cytokine expression. This immunomodulation may be an important mechanism via which titanium surface modification influences osseointegration.

Cathodic Polarization Coats Titanium Based Implant Materials with Enamel Matrix Derivate (EMD)

The idea of a bioactive surface coating that enhances bone healing and bone growth is a strong focus of on-going research for bone implant materials. Enamel matrix derivate (EMD) is well documented to support bone regeneration and activates growth of mesenchymal tissues. Thus, it is a prime candidate for coating of existing implant surfaces. The aim of this study was to show that cathodic polarization can be used for coating commercially available implant surfaces with an immobilized but functional and bio-available surface layer of EMD. After coating, XPS revealed EMD-related bindings on the surface while SIMS showed incorporation of EMD into the surface. The hydride layer of the original surface could be activated for coating in an integrated one-step process that did not require any pre-treatment of the surface. SEM images showed nano-spheres and nano-rods on coated surfaces that were EMD-related. Moreover, the surface roughness remained unchanged after coating, as it was shown by optical profilometry. The mass peaks observed in the matrix-assisted laser desorption/ionization time-of-flight mass spectroscopy (MALDI-TOF MS) analysis confirmed the integrity of EMD after coating. Assessment of the bioavailability suggested that the modified surfaces were active for osteoblast like MC3M3-E1 cells in showing enhanced Coll-1 gene expression and ALP activity.

Mesenchymal stem cell response to UV-photofunctionalized TiO2coated CoCrMo

UV photofunctionalization of TiO₂coated implant surfaces enhanced markers of cell adhesion. This may prove to be advantageous for orthopaedic implants by supporting the colonisation and adhesion of cells capable of facilitating in bone healing.

Genetic networks in osseointegration

Osseointegration-based dental implants have become a well-accepted treatment modality for complete and partial edentulism. The success of this treatment largely depends on the stable integration and maintenance of implant fixtures in alveolar bone; however, the molecular and cellular mechanisms regulating this unique tissue reaction have not yet been fully uncovered. Radiographic and histologic observations suggest the sustained retention of peri-implant bone without an apparent susceptibility to catabolic bone remodeling; therefore, implant-induced bone formation continues to be intensively investigated. Increasing numbers of whole-genome transcriptome studies suggest complex molecular pathways that may play putative roles in osseointegration. This review highlights genetic networks related to bone quality, the transient chondrogenic phase, the vitamin D axis, and the peripheral circadian rhythm to elute the regulatory mechanisms underlying the establishment and maintenance of osseointegration.

Early bone apposition to hydrophilic and hydrophobic titanium implant surfaces: a histologic and histomorphometric study in minipigs

OBJECTIVE

The first objective of this pilot study was to evaluate the impact of the hydrophilicity on the early phases of osseointegration. The second objective was to compare two hydrophilic implant surfaces with different geometries, surface roughness, and technologies achieving hydrophilicity.

MATERIAL AND METHODS

Twelve weeks after extraction, all four quadrants of nine minipigs received three dental implants, alternating between hydrophilic microrough surfaces (INICELL and SLActive) and a conventional hydrophobic microrough surface. After 5, 10, and 15 days of submerged healing, ground sections were prepared and subjected to histologic and histomorphometric analysis.

RESULTS

The histologic analysis revealed a similar healing pattern among the hydrophilic and hydrophobic implant surfaces, with extensive bone formation occurring between day 5 and day 10. With BIC values of greater than 50% after 10 days, all examined surfaces indicated favorable osseointegration at this very early point in healing. At day 15, the mean new bone-to-implant contact (newBIC) of one hydrophilic surface (INICELL; 55.8 ± 14.4%) was slightly greater than that of the hydrophobic microrough surface (40.6 ± 20.2%). At day 10 and day 15, an overall of 21% of the implants had to be excluded from analysis due to inflammations primarily caused by surgical complications.

CONCLUSION

Substantial bone apposition occurs between day 5 and day 10. The data suggest that the hydrophilic surface can provoke a slight tendency toward increased bone apposition in minipigs after 15 days. A direct comparison of two hydrophilic surfaces with varying geometries is of limited relevance.

Differential response of human gingival fibroblasts to titanium- and titanium-zirconium-modified surfaces

BACKGROUND AND OBJECTIVE

Gingival fibroblasts are responsible for the constant adaptation, wound healing and regeneration of gingival connective tissue. New titanium-zirconium (TiZr) abutment surfaces have been designed to improve soft tissue integration and reduce implant failure compared with titanium (Ti). The aim of the present study was first to characterize a primary human gingival fibroblast (HGF) model and secondly to evaluate their differential response to Ti and TiZr polished (P), machined (M) and machined + acid-etched (modMA) surfaces, respectively.

MATERIAL AND METHODS

HGF were cultured on tissue culture plastic or on the different Ti and TiZr surfaces. Cell morphology was evaluated through confocal and scanning electron microscopy. A wound healing assay was performed to evaluate the capacity of HGF to close a scratch. The expression of genes was evaluated by real-time RT-PCR, addressing: (i) extracellular matrix organization and turnover; (ii) inflammation; (iii) cell adhesion and structure; and (iv) wound healing. Finally, cells on Ti/TiZr surfaces were immunostained with anti-ITGB3 antibodies to analyze integrin β3 production. Matrix metalloproteinase-1 (MMP1) and inhibitor of metallopeptidases-1 (TIMP1) production were analyzed by enzyme-linked immunosorbent assays.

RESULTS

On tissue culture plastic, HGF showed no differences between donors on cell proliferation and on the ability for wound closure; α-smooth muscle actin was overexpressed on scratched monolayers. The differentiation profile showed increased production of extracellular matrix components. Ti and TiZr showed similar biocompatibility with HGF. TiZr increased integrin-β3 mRNA and protein levels, compared with Ti. Cells on TiZr surfaces showed higher MMP1 protein than Ti surfaces, although similar TIMP1 protein production. In this in vitro experiment, P and M surfaces from both Ti and TiZr showed better HGF growth than modMA.

CONCLUSION

Taking into account the better mechanical properties and bioactivity of TiZr compared with Ti, the results of the present study show that TiZr is a potential clinical candidate for soft tissue integration and implant success.

In vivo assessment of bone healing following Piezotome® ultrasonic instrumentation

PURPOSE

This pilot study evaluated the molecular, histologic, and radiographic healing of bone to instrumentation with piezoelectric or high speed rotary (R) devices over a 3-week healing period.

MATERIAL AND METHODS

Fourteen Sprague-Dawley rats (Charles River Laboratories International, Inc., Wilmington, MA, USA) underwent bilateral tibial osteotomies prepared in a randomized split-leg design using Piezotome® (P1) (Satelec Acteon, Merignac, France), Piezotome 2® (P2) (Satelec Acteon), High-speed R instrumentation, or sham surgery (S). At 1 week, an osteogenesis array was used to evaluate differences in gene expression while quantitative analysis assessed percentage bone fill (PBF) and bone mineral density (BMD) in the defect, peripheral, and distant regions at 3 weeks. Qualitative histologic evaluation of healing osteotomies was also performed at 3 weeks.

RESULTS

At 1 week, expression of 11 and 18 genes involved in bone healing was significantly (p < .05) lower following P1 and P2 instrumentation, respectively, relative to S whereas 16 and 4 genes were lower relative to R. No differences in PBF or BMD were detected between groups within the osteotomy defect. However, significant differences in PBF (p = .020) and BMD (p = .008) were noted along the peripheral region between P2 and R groups, being R the group with the lowest values. Histologically, smooth osteotomy margins were present following instrumentation using P1 or P2 relative to R.

CONCLUSIONS

Piezoelectric instrumentation favors preservation of bone adjacent to osteotomies while variations in gene expression suggest differences in healing rates due to surgical modality. Bone instrumented by piezoelectric surgery appears less detrimental to bone healing than high-speed R device.

The Control of Mesenchymal Stromal Cell Osteogenic Differentiation through Modified Surfaces

Stem cells continue to receive widespread attention due to their potential to revolutionise treatments in the fields of both tissue engineering and regenerative medicine. Adult stem cells, specifically mesenchymal stromal cells (MSCs), play a vital role in the natural events surrounding bone healing and osseointegration through being stimulated to differentiate along their osteogenic lineage and in doing so, they form new cortical and trabecular bone tissue. Understanding how to control, manipulate, and enhance the intrinsic healing events modulated through osteogenic differentiation of MSCs by the use of modified surfaces and biomaterials could potentially advance the fields of both orthopaedics and dentistry. This could be by either using surface modification to generate greater implant stability and more rapid healing following implantation or the stimulation of MSCs ex vivo for reimplantation. This review aims to gather publications targeted at promoting, enhancing, and controlling the osteogenic differentiation of MSCs through biomaterials, nanotopographies, and modified surfaces for use in implant procedures.