The adhesive strategies of cyprids and development of barnacle-resistant marine coatings

Antifouling properties of hydrogels

Marine sessile organisms easily adhere to submerged solids such as rocks, metals and plastics, but not to seaweeds and fishes, which are covered with soft and wet 'hydrogel'. Inspired by this fact, we have studied long-term antifouling properties of hydrogels against marine sessile organisms. Hydrogels, especially those containing hydroxy group and sulfonic group, show excellent antifouling activity against barnacles both in laboratory assays and in the marine environment. The extreme low settlement on hydrogels in vitro and in vivo is mainly caused by antifouling properties against the barnacle cypris.

Effects of surface charge and Gibbs surface energy on the settlement behaviour of barnacle cyprids (Balanus amphitrite)

Gibbs surface energy has long been considered to be an important parameter in the design of fouling-resistant surfaces for marine applications. Rigorous testing of the hypothesis that settlement is related to Gibbs surface energy however has never been accomplished, due mainly to practical limitations imposed by the necessary combination of surface engineering and biological evaluation methods. In this article, the effects of surface charge and Gibbs surface energy on the settlement of cyprids of an important fouling barnacle, Balanus amphitrite, were evaluated. Settlement assays were conducted on a range of self-assembled monolayers (SAMs) (CH(3)-, OH-, COOH-, N(CH(3))(3) (+)-, NH(2)-terminated), presented in gold-coated polystyrene well plates, varying in terms of their surface charge and Gibbs surface energy. Contrary to contemporary theory, settlement was not increased by high-energy surfaces, rather the opposite was found to be the case with cyprids settling in greater numbers on a low-energy CH(3)- SAM compared to a high-energy OH- SAM. Settlement was also greater on negatively-charged SAMs, compared to neutral and positively-charged SAMs. These findings are discussed in the context of data drawn from surfaces that varied in multiple characteristics simultaneously, as have been used previously for such experiments. The finding that surface charge, rather than total surface energy, may be responsible for surface selection by cyprids, will have significant implications for the design of future fouling-resistant materials.

The development of marine biofilms on two commercial non-biocidal coatings: a comparison between silicone and fluoropolymer technologies

The antimicrobial performance of two fouling-release coating systems, Intersleek 700® (IS700; silicone technology), Intersleek 900® (IS900; fluoropolymer technology) and a tie coat (TC, control surface) was investigated in a short term (10 days) field experiment conducted at a depth of ca 0.5 m in the Marina Bandar Rawdha (Muscat, Oman). Microfouling on coated glass slides was analyzed using epifluorescence microscopy and adenosine-5'-triphosphate (ATP) luminometry. All the coatings developed biofilms composed of heterotrophic bacteria, cyanobacteria, seven species of diatoms (2 species of Navicula, Cylindrotheca sp., Nitzschia sp., Amphora sp., Diploneis sp., and Bacillaria sp.) and algal spores (Ulva sp.). IS900 had significantly thinner biofilms with fewer diatom species, no algal spores and the least number of bacteria in comparison with IS700 and the TC. The ATP readings did not correspond to the numbers of bacteria and diatoms in the biofilms. The density of diatoms was negatively correlated with the density of the bacteria in biofilms on the IS900 coating, and, conversely, diatom density was positively correlated in biofilms on the TC. The higher antifouling efficacy of IS900 over IS700 may lead to lower roughness and thus lower fuel consumption for those vessels that utilise the IS900 fouling-release coating.

Antibiofouling hybrid dendritic Boltorn/star PEG thiol-ene cross-linked networks

A series of thiol-ene generated amphiphilic cross-linked networks was prepared by reaction of alkene-modified Boltorn polyesters (Boltorn-ene) with varying weight percent of 4-armed poly(ethylene glycol) (PEG) tetrathiol (0-25 wt%) and varying equivalents of pentaerythritol tetrakis(3-mercaptopropionate) (PETMP) (0-64 wt%). These materials were designed to present complex surface topographies and morphologies, with heterogeneity of surface composition and properties and robust mechanical properties, to serve as nontoxic antibiofouling coatings that are amenable to large-scale production for application in the marine environment. Therefore, a two-dimensional matrix of materials compositions was prepared to study the physical and mechanical properties, over which the compositions spanned from 0 to 25 wt% PEG tetrathiol and 0-64 wt% PETMP (the overall thiol/alkene (SH/ene) ratios ranged from 0.00 to 1.00 equiv), with both cross-linker weight percentages calculated with respect to the weight of Boltorn-ene. The Boltorn-ene components were prepared through the esterification of commercially available Boltorn H30 with 3-butenoic acid. The subsequent cross-linking of the Boltorn-PEG-PETMP films was monitored using IR spectroscopy, where it was found that near-complete consumption of both thiol and alkene groups occurred when the stoichiometry was ca. 48 wt% PETMP (0.75 equiv SH/ene, independent of PEG amount). The thermal properties of the films showed an increase in T(g) with an increase in 4-armed PEG-tetrathiol wt%, regardless of the PETMP concentration. Investigation of the bulk mechanical properties in dry and wet states found that the Young's modulus was the greatest at 48 wt% PETMP (0.75 equiv of SH/ene). The ultimate tensile strength increased when PETMP was constant and the PEG concentration was increased. The Young's modulus was slightly lower for wet films at constant PEG or constant PETMP amounts, than for the dry samples. The nanoscopic surface features were probed using atomic force microscopy (AFM), where it was observed that the surface of the amphiphilic films became increasingly rough with increasing PEG wt%. On the basis of the physicochemical data from the diverse sample matrix, a focused compositional profile was then investigated further to determine the antifouling performance of the cross-linked Boltorn-PEG-PETMP networks. For these studies, a low, constant PETMP concentration of 16 wt% was maintained with variation in the PEG wt% (0-35 wt%). Antifouling and fouling-release activities were tested against the marine alga Ulva. Spore settlement densities were low on these films, compared to that on standards of polydimethylsiloxane and glass.

Real-time quantification of microscale bioadhesion events in situ using imaging surface plasmon resonance (iSPR)

From macro- to nanoscales, adhesion phenomena are all-pervasive in nature yet remain poorly understood. In recent years, studies of biological adhesion mechanisms, terrestrial and marine, have provided inspiration for "biomimetic" adhesion strategies and important insights for the development of fouling-resistant materials. Although the focus of most contemporary bioadhesion research is on large organisms such as marine mussels, insects and geckos, adhesion events on the micro/nanoscale are critical to our understanding of important underlying mechanisms. Observing and quantifying adhesion at this scale is particularly relevant for the development of biomedical implants and in the prevention of marine biofouling. However, such characterization has so far been restricted by insufficient quantities of material for biochemical analysis and the limitations of contemporary imaging techniques. Here, we introduce a recently developed optical method that allows precise determination of adhesive deposition by microscale organisms in situ and in real time; a capability not before demonstrated. In this extended study we used the cypris larvae of barnacles and a combination of conventional and imaging surface plasmon resonance techniques to observe and quantify adhesive deposition onto a range of model surfaces (CH(3)-, COOH-, NH(3)-, and mPEG-terminated SAMs and a PEGMA/HEMA hydrogel). We then correlated this deposition to passive adsorption of a putatively adhesive protein from barnacles. In this way, we were able to rank surfaces in order of effectiveness for preventing barnacle cyprid exploration and demonstrate the importance of observing the natural process of adhesion, rather than predicting surface effects from a model system. As well as contributing fundamentally to the knowledge on the adhesion and adhesives of barnacle larvae, a potential target for future biomimetic glues, this method also provides a versatile technique for laboratory testing of fouling-resistant chemistries.

Mechanisms of temporary adhesion in benthic animals

Adhesive systems are ubiquitous in benthic animals and play a key role in diverse functions such as locomotion, food capture, mating, burrow building, and defence. For benthic animals that release adhesives, surface and material properties and external morphology have received little attention compared to the biochemical content of the adhesives. We address temporary adhesion of benthic animals from the following three structural levels: (a) the biochemical content of the adhesive secretions, (b) the micro- and mesoscopic surface geometry and material properties of the adhesive organs, and (c) the macroscopic external morphology of the adhesive organs. We show that temporary adhesion of benthic animals is affected by three structural levels: the adhesive secretions provide binding to the substratum at a molecular scale, whereas surface geometry and external morphology increase the contact area with the irregular and unpredictable profile of the substratum from micro- to macroscales. The biochemical content of the adhesive secretions differs between abiotic and biotic substrata. The biochemistry of the adhesives suitable for biotic substrata differentiates further according to whether adhesion must be activated quickly (e.g. as a defensive mechanism) or more slowly (e.g. during adhesion of parasites). De-adhesion is controlled by additional secretions, enzymes, or mechanically. Due to deformability, the adhesive organs achieve intimate contact by adapting their surface profile to the roughness of the substratum. Surface projections, namely cilia, cuticular villi, papillae, and papulae increase the contact area or penetrate through the secreted adhesive to provide direct contact with the substratum. We expect that the same three structural levels investigated here will also affect the performance of artificial adhesive systems.

Deep sequencing of naupliar-, cyprid- and adult-specific normalised Expressed Sequence Tag (EST) libraries of the acorn barnacle Balanus amphitrite

In order to improve the genetic characterisation of the barnacle Balanus amphitrite, normalised EST libraries for the developmental stages, viz. nauplius (a mix of instars I and II), cyprid and adult, were generated. The libraries were sequenced independently using 454 technologies and 575,666 reads were generated. For adults, 4843 unique isotigs were estimated and 6754 and 7506 in the cyprid and naupliar stage, respectively. It was found that some of the previously proposed cyprid-specific bcs genes were also expressed during the naupliar and adult stage. Furthermore, as lectins have been hypothesised to influence settlement cue recognition in barnacles, the database was searched for lectin-like isotigs. Two proteins, uniquely expressed in either the cyprid or the adult stage, matched a mannose receptor, and their nucleotide sequences were 33% and 31% identical to a lectin (BRA-3) isolated from Megabalanus rosa. Further characterisation of these genes may suggest their involvement in settlement.

Isolation and physico-chemical characterisation of extracellular polymeric substances produced by the marine bacterium Vibrio parahaemolyticus

A marine bacterial strain identified as Vibrio parahaemolyticus by 16S rRNA gene (HM355955) sequencing and gas chromatography (GC) coupled with MIDI was selected from a natural biofilm by its capability to produce extracellular polymeric substances (EPS). The EPS had an average molecule size of 15.278 μm and exhibited characteristic diffraction peaks at 5.985°, 9.150° and 22.823°, with d-spacings of 14.76661, 9.29989 and 3.89650 Å, respectively. The Fourier-transform infrared spectroscopy (FTIR) spectrum revealed aliphatic methyl, primary amine, halide groups, uronic acid and saccharides. Gas chromatography mass spectrometry (GCMS) confirmed the presence of arabinose, galactose, glucose and mannose. (1)HNMR (nuclear magnetic resonance) revealed functional groups characteristic of polysaccharides. The EPS were amorphous in nature (CI(xrd) 0.092), with a 67.37% emulsifying activity, thermostable up to 250°C and displayed pseudoplastic rheology. MALDI-TOF-TOF analysis revealed a series of masses, exhibiting low-mass peaks (m/z) corresponding to oligosaccharides and higher-mass peaks for polysaccharides consisting of different ratios of pentose and hexose moieties. This is the first report of a detailed characterisation of the EPS produced by V. parahaemolyticus, which could be further explored for biotechnological and industrial use.

Antifouling coatings: recent developments in the design of surfaces that prevent fouling by proteins, bacteria, and marine organisms

The major strategies for designing surfaces that prevent fouling due to proteins, bacteria, and marine organisms are reviewed. Biofouling is of great concern in numerous applications ranging from biosensors to biomedical implants and devices, and from food packaging to industrial and marine equipment. The two major approaches to combat surface fouling are based on either preventing biofoulants from attaching or degrading them. One of the key strategies for imparting adhesion resistance involves the functionalization of surfaces with poly(ethylene glycol) (PEG) or oligo(ethylene glycol). Several alternatives to PEG-based coatings have also been designed over the past decade. While protein-resistant coatings may also resist bacterial attachment and subsequent biofilm formation, in order to overcome the fouling-mediated risk of bacterial infection it is highly desirable to design coatings that are bactericidal. Traditional techniques involve the design of coatings that release biocidal agents, including antibiotics, quaternary ammonium salts (QAS), and silver, into the surrounding aqueous environment. However, the emergence of antibiotic- and silver-resistant pathogenic strains has necessitated the development of alternative strategies. Therefore, other techniques based on the use of polycations, enzymes, nanomaterials, and photoactive agents are being investigated. With regard to marine antifouling coatings, restrictions on the use of biocide-releasing coatings have made the generation of nontoxic antifouling surfaces more important. While considerable progress has been made in the design of antifouling coatings, ongoing research in this area should result in the development of even better antifouling materials in the future.

Video observation of surface exploration in cyprids of Balanus amphitrite: the movements of antennular sensory setae

Video microscopy of cyprids of Balanus amphitrite was used to monitor the action of antennular setae during the exploratory behaviour prior to attachment. In addition, SEM was used to provide a revised description of all antennular setae for that species. The videos describe if a particular seta touches the substratum and the area it can cover during surface exploration. On the fourth segment, the plumose terminal setae A and B are never in contact with the substratum, lack a terminal pore and it is argued that they sense hydrodynamic forces. The aesthetasc-like terminal seta D is likewise held free in the water at all times and it is speculated that it senses dissolved substances, but, since it contains a scolopale rod, it must also have a mechano-receptive function. All remaining antennular setae on the second, third and fourth segments have a terminal pore and it is argued that these are bimodal receptors with both chemo- and mechano-receptive modalities. These setae are also at one time or another in contact with the substratum, except perhaps for the small preaxial seta 2 and terminal seta C. The first seta to contact the surface during a tentative step is radial seta 5, which is longer than all other radial setae. All other setae on the second and third segment are only in contact after a step is completed. When the attachment disc touches the surface (=a step completed) the long and curved postaxial seta 2 (on the second segment) and postaxial seta 3 on the third segment are both flexed to either side of the antennule. This lateral displacement ensures that these two setae can touch large surface areas to either side of the appendage. The four subterminal setae on the fourth segment contact the surface both immediately before and after a step has been completed, and the constant flicking of the segment significantly increases the surface area tested by both these chemoreceptors and by terminal seta E, which can sweep up to 60 μm laterally from the attachment disc. The flicking of the fourth segment may also serve to dilute the boundary layer of chemoreceptors on the fourth segment such as the aesthetasc-like terminal seta D and thus facilitate the detection of new stimuli.

Effect of ultrasound on cyprids and juvenile barnacles

Settlement inhibition of barnacle (Amphibalanus amphitrite) cypris larvae resulting from exposure to ultrasound was measured at three frequencies (23, 63, and 102 kHz), applied at three acoustic pressure levels (9, 15, and 22 kPa) for exposure times of 30, 150, and 300 s. The lowest settlement was observed for 23 kHz, which also induced the highest cyprid mortality. Cyprid settlement following exposure to 23 kHz at 22 kPa for 30 s was reduced by a factor of two. Observing surface exploration by the cyprids revealed an altered behaviour following exposure to ultrasound: step length was increased, while step duration, walking pace, and the fraction of cyprids exploring the surface were significantly reduced with respect to control cyprids. The basal area of juvenile barnacles, metamorphosed from ultrasound-treated cyprids was initially smaller than unexposed individuals, but normalised over two weeks' growth. Thus, ultrasound exposure effectively reduced cyprid settlement, yet metamorphosed barnacles grew normally.

Engineered antifouling microtopographies: mapping preferential and inhibitory microenvironments for zoospore attachment

An algorithm was developed and implemented to map the locations of attached spores of Ulva linza on patterned surfaces. Using this mapping algorithm, spore preference among regions within a pattern can be detected and quantified. Settlement maps of spores on patterned topographies from several assays showed clear preferences in spore settlement. Over 94% of the spores attached within the depressed regions on the surfaces, including a surface containing pits instead of protruding features. The spores attached primarily at the intersections of several features, with over half and up to 96% of spores settling in these regions. The highest spore densities occurred at intersections where the features were most dissimilar. In contrast, the location of attached beads on the surfaces was nearly uniform across the surface. Identification of preferential attachment locations allows for the study of localized properties that influence cell behavior and aids in the development of new surfaces to control cell-surface interactions.

Species-specific detection and quantification of common barnacle larvae from the Japanese coast using quantitative real-time PCR

Species-specific detection and quantification methods for barnacle larvae using quantitative real-time polymerase chain reaction (qPCR) were developed. Species-specific primers for qPCR were designed for 13 barnacle species in the mitochondrial 12S ribosomal RNA gene region. Primer specificity was examined by PCR using template DNA extracted from each of the 13 barnacle species, other unidentified barnacle species, and field collected zooplankton samples. The resulting PCR products comprised single bands following agarose gel electrophoresis when the templates corresponded to primers. The amplifications were highly species-specific even for the field plankton samples. The field plankton samples were subjected to qPCR assay. The calculated DNA contents for each barnacle species were closely correlated with the number of larvae measured by microscopic examination. The method could be applied to quantify barnacle larvae in natural plankton samples.

Absence of cross-linking via trans-glutaminase in barnacle cement and redefinition of the cement

Balanomorphan barnacles attach their calcareous bases to a variety of substrata, including others of the same species, through secretion of an underwater adhesive, commonly referred to as cement. In this multi-functional process of underwater attachment, curing of the adhesive is crucial for the formation of a secure attachment. To date, there has been no direct evidence presented to suggest the involvement of cross-linking or polymerization in the cement curing process, despite the emergence of this hypothesis in the recent literature. A recently proposed mechanism for cement curing involves glutamyl-lysine cross-linking via the action of trans-glutaminase. However, in the opinion of the author, inadequate attention may have been paid to sample collection during the study and the conditions used in the analysis may not be adequate to support the conclusions of the paper. Indeed, further investigation, the results of which are presented here, did not provide any evidence to support adhesive curing via glutamyl-lysine cross-linking. Therefore, the hypothesis that the process of cement curing is similar to the clotting system of barnacle hemolymph is not compatible with the data reported so far. In order to allay any potential confusion, a new definition of the barnacle cement is proposed.

Modulation of barnacle (Balanus amphitrite Darwin) cyprid settlement behavior by sulfobetaine and carboxybetaine methacrylate polymer coatings

Zwitterionic polymers such as poly(sulfobetaine methacrylate) (polySBMA) and poly(carboxybetaine methacrylate) (polyCBMA) have demonstrated impressive fouling-resistance against proteins and mammalian cells. In this paper, the effects of these surface chemistries on the settlement and behavior of an ubiquitous fouling organism, the cypris larva of the barnacle Balanus amphitrite (=Amphibalanus amphitrite), were studied in the laboratory. Conventional settlement assays and behavioral analysis of cyprids using Noldus Ethovision 3.1 demonstrated significant differences in settlement and behavior on different surfaces. Cyprids did not settle on the polySBMA or polyCBMA surfaces over the course of the assay, whereas settlement on glass occurred within expected limits. Individual components of cyprid behavior were shown to differ significantly between glass, polySBMA and polyCBMA. Cyprids also responded differently to the two zwitterionic surfaces. On polySBMA, cyprids were unwilling or unable to settle, whereas on polyCBMA cyprids did not attempt exploration and left the surface quickly. In neither case was toxicity observed. It is concluded that a zwitterionic approach to fouling-resistant surface development has considerable potential in marine applications.

'Flying barnacles': implications for the spread of non-indigenous species

The presence of adult barnacles of Fistulobalanus pallidus (Darwin) and Fistulobalanus albicostatus (Pilsbry) attached to field-readable plastic leg rings on the Lesser Black-backed Gull Larus fuscus in Northern Europe is reported. L. fuscus is a long-distance palaearctic migrant, breeding in temperate areas spreading widely over inland and marine habitats outside the breeding season. The species is known to perform long-distance migration to Africa and the Middle East. Combining present knowledge on the birds' migratory pattern and the home range of the barnacle species, it is concluded that the cypris larvae of F. pallidus must have settled in African waters, whereas the area where F. albicostatus settled on the bird leg rings is less certain. The barnacles were of adult size and must thus have been attached for a period of no less than 2 months. More than 30 individual barnacles could occur together on a single field-readable plastic leg ring. The barnacles could therefore, if ported alive to a new area, reproduce successfully and thus either introduce the species or genetically affect other native populations. This may pose a new and wholly unexpected transportation pathway for barnacles as invasive species.

Amphiphilic surface active triblock copolymers with mixed hydrophobic and hydrophilic side chains for tuned marine fouling-release properties

Two series of amphiphilic triblock surface active block copolymers (SABCs) were prepared through chemical modification of two polystyrene-block-poly(ethylene-ran-butylene)-block-polyisoprene ABC triblock copolymer precursors. The methyl ether of poly(ethylene glycol) [M(n) approximately 550 g/mol (PEG550)] and a semifluorinated alcohol (CF(3)(CF(2))(9)(CH(2))(10)OH) [F10H10] were attached at different molar ratios to impart both hydrophobic and hydrophilic groups to the isoprene segment. Coatings on glass slides consisting of a thin layer of the amphiphilic SABC deposited on a thicker layer of an ABA polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene thermoplastic elastomer were prepared for biofouling assays with algae. Dynamic water contact angle analysis, X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine structure (NEXAFS) measurements were utilized to characterize the surfaces. Clear differences in surface structure were realized as the composition of attached side chains was varied. In biofouling assays, the settlement (attachment) of zoospores of the green alga Ulva was higher for surfaces incorporating a large proportion of the hydrophobic F10H10 side chains, while surfaces with a large proportion of the PEG550 side chains inhibited settlement. The trend in attachment strength of sporelings (young plants) of Ulva did not show such an obvious pattern. However, amphiphilic SABCs incorporating a mixture of PEG550 and F10H10 side chains performed the best. The number of cells of the diatom Navicula attached after exposure to flow decreased as the content of PEG550 to F10H10 side chains increased.

Characterization of the adhesive plaque of the barnacle Balanus amphitrite: amyloid-like nanofibrils are a major component

The nanoscale morphology and protein secondary structure of barnacle adhesive plaques were characterized using atomic force microscopy (AFM), far-UV circular dichroism (CD) spectroscopy, transmission Fourier transform infrared (FTIR) spectroscopy, and Thioflavin T (ThT) staining. Both primary cement (original cement laid down by the barnacle) and secondary cement (cement used for reattachment) from the barnacle Balanus amphitrite (= Amphibalanus amphitrite) were analyzed. Results showed that both cements consisted largely of nanofibrillar matrices having similar composition. Of particular significance, the combined results indicate that the nanofibrillar structures are consistent with amyloid, with globular protein components also identified in the cement. Potential properties, functions, and formation mechanisms of the amyloid-like nanofibrils within the adhesive interface are discussed. Our results highlight an emerging trend in structural biology showing that amyloid, historically associated with disease, also has functional roles.

A model that predicts the attachment behavior of Ulva linza zoospores on surface topography

A predictive model for the attachment of spores of the green alga Ulva on patterned topographical surfaces was developed using a constant refinement approach. This 'attachment model' incorporated two historical data sets and a modified version of the previously-described Engineered Roughness Index. Two sets of newly-designed surfaces were used to evaluate the effect of two components of the model on spore settlement. Spores attached in fewer numbers when the area fraction of feature tops increased or when the number of distinct features in the design increased, as predicted by the model. The model correctly predicted the spore attachment density on three previously-untested surfaces relative to a smooth surface. The two historical data sets and two new data sets showed high correlation (R(2) = 0.88) with the model. This model may be useful for designing new antifouling topographies.

Atomic force microscopy of the morphology and mechanical behaviour of barnacle cyprid footprint proteins at the nanoscale

Barnacles are a major biofouler of man-made underwater structures. Prior to settlement, cypris larvae explore surfaces by reversible attachment effected by a 'temporary adhesive'. During this exploratory behaviour, cyprids deposit proteinaceous 'footprints' of a putatively adhesive material. In this study, footprints deposited by Balanus amphitrite cyprids were probed by atomic force microscopy (AFM) in artificial sea water (ASW) on silane-modified glass surfaces. AFM images obtained in air yielded better resolution than in ASW and revealed the fibrillar nature of the secretion, suggesting that the deposits were composed of single proteinaceous nanofibrils, or bundles of fibrils. The force curves generated in pull-off force experiments in sea water consisted of regions of gradually increasing force, separated by sharp drops in extension force manifesting a characteristic saw-tooth appearance. Following the relaxation of fibrils stretched to high strains, force-distance curves in reverse stretching experiments could be described by the entropic elasticity model of a polymer chain. When subjected to relaxation exceeding 500 ms, extended footprint proteins refolded, and again showed saw-tooth unfolding peaks in subsequent force cycles. Observed rupture and hysteresis behaviour were explained by the 'sacrificial bond' model. Longer durations of relaxation (>5 s) allowed more sacrificial bond reformation and contributed to enhanced energy dissipation (higher toughness). The persistence length for the protein chains (L(P)) was obtained. At high elongation, following repeated stretching up to increasing upper strain limits, footprint proteins detached at total stretched length of 10 microm.

A passive apparatus for controlled-flux delivery of biocides: hydrogen peroxide as an example

A new test method has been developed to estimate the required release rate of hydrogen peroxide (H2O2) to prevent marine biofouling. The technique exploits a well-defined concentration gradient of biocide across a cellulose acetate membrane. A controlled flux of H2O2, an environmentally friendly biocide, was obtained. Larvae of the barnacle, Balanus improvisus, were subjected to known release rates of H2O2 from a surface, under laboratory conditions. It was found that the distribution of settled larvae was not significantly different from the controls when H2O2 fluxes of 5-8 microg cm(-2) day(-1) were applied. However, release rates of 40 microg cm(-2) day(-1) significantly displaced the distribution of settled larvae towards the area of the chamber farthest away from the membrane. Membrane tests in seawater (Jyllinge Harbour, Denmark) for over 16 weeks showed that release rates of H2O2 of approximately 2800 microg cm(-2) day(-1) deterred biofouling efficiently. A H2O2 release rate of about 224 microg cm(-2) day(-1) resulted in some slime formation, but it was less than that on the H2O2-free control. It appears that to obtain efficient resistance to biofouling in natural seawater requires much higher membrane release rates of H2O2 (factor of between 5 and 50) than laboratory membrane exposure assays using barnacle larvae.

Enzymatic generation of hydrogen peroxide shows promising antifouling effect

The antifouling (AF) potential of hydrogen peroxide (H(2)O(2)) produced enzymatically in a coating containing starch, glucoamylase, and hexose oxidase was evaluated in a series of laboratory tests and in-sea field trials. Dissolved H(2)O(2) inhibited bacterial biofilm formation by eight of nine marine Proteobacteria, tested in microtiter plates. However, enzymatically produced H(2)O(2) released from a coating did not impede biofilm formation by bacteria in natural seawater tested in a biofilm reactor. A field trial revealed a noticeable effect of the enzyme system: after immersion in the North Sea for 97 days, the reference coating without enzymes had 35-40 barnacles, 10% area coverage by diatoms and 15% area coverage by tunicates. The enzyme containing coating had only 6-12 barnacles, 10% area coverage by diatoms and no tunicates. The enzyme system had a performance similar to a copper-based commercial coating and thus appears to have potential as a non-persistent AF agent.

Attachment strength is a key factor in the selection of surfaces by barnacle cyprids (Balanus amphitrite) during settlement

This manuscript constitutes the first evidence of the effects of texture on the rate of removal of cyprids from surfaces and the link between settlement preferences and susceptibility to removal by force. Cyprids of Balanus amphitrite settled preferentially on sinusoidal linear textures (1:1 aspect ratio) in the range 0-32 microm, with textures on the scale of the cyprid (512 microm) treated as flat. Polycarbonate was preferred as a substratum to a polydimethylsiloxane (PDMS) elastomer. Textures of 64-256 microm were avoided and the texture of 256 microm in PDMS was the least preferred substratum tested, with no settlement of cyprids. Hydrodynamic removal was inversely correlated to settlement rate on the textures assayed, implying an adaptive response by cyprids to select surface textures to which their attachment was most tenacious. Correlation plots suggest that likelihood of removal by force is not the only factor involved when cyprids elect to settle on a given texture. Choice and no-choice assays delivered different results. This discrepancy is partially ascribed to inherent variability in the choice assay method, but also to the ability of cyprids to compare textures and exercise true choice, biasing settlement towards stimulatory textures in preference to intermediate textures that were settled on in the absence of choice. The identification of a link between settlement preference and likelihood of removal will assist practically in the development of fouling-resistant marine coatings.

The role of nano-roughness in antifouling

Nano-engineered superhydrophobic surfaces have been investigated for potential fouling resistance properties. Integrating hydrophobic materials with nanoscale roughness generates surfaces with superhydrophobicity that have water contact angles (theta) >150 degrees and concomitant low hysteresis (<10 degrees ). Three superhydrophobic coatings (SHCs) differing in their chemical composition and architecture were tested against major fouling species (Amphora sp., Ulva rigida, Polysiphonia sphaerocarpa, Bugula neritina, Amphibalanus amphitrite) in settlement assays. The SHC which had nanoscale roughness alone (SHC 3) deterred the settlement of all the tested fouling organisms, compared to selective settlement on the SHCs with nano- and micro-scale architectures. The presence of air incursions or nanobubbles at the interface of the SHCs when immersed was characterized using small angle X-ray scattering, a technique sensitive to local changes in electron density contrast resulting from partial or complete wetting of a rough interface. The coating with broad spectrum antifouling properties (SHC 3) had a noticeably larger amount of unwetted interface when immersed, likely due to the comparatively high work of adhesion (60.77 mJ m(-2) for SHC 3 compared to 5.78 mJ m(-2) for the other two SHCs) required for creating solid/liquid interface from the solid/vapour interface. This is the first example of a non-toxic, fouling resistant surface against a broad spectrum of fouling organisms ranging from plant cells and non-motile spores, to complex invertebrate larvae with highly selective sensory mechanisms. The only physical property differentiating the immersed surfaces is the nano-architectured roughness which supports longer standing air incursions providing a novel non-toxic broad spectrum mechanism for the prevention of biofouling.

Quantifying the exploratory behaviour of Amphibalanus amphitrite cyprids

The behavioural response of cypris larvae from A. amphitrite (=Balanus amphitrite) exploring three model glass surfaces is quantified by close-range microscopy. Step length and step duration measurements reveal a response to both surface properties and flow. Without flow, 2-day-old cyprids took larger steps with shorter step duration on hydrophilic glass surfaces (bare and NH2-treated) vs hydrophobic glass (CH3-treated). These parameters suggest a more detailed, local inspection of hydrophobic surfaces and a more extensive exploration for hydrophilic surfaces. Cyprids under flow took longer steps and exhibited shorter probing times on hydrophobic glass. On hydrophilic glass, cyprids increased their step duration under flow. This active response is attributed to drag and lift forces challenging the cyprids' temporary anchoring to the substratum. Seven-day-old cyprids showed almost no discrimination between the model surfaces. Microscopic-scale observation of cyprid exploration is expected to provide new insights into interactions between cyprids and surfaces.

The serine protease Esperase HPF inhibits the formation of multispecies biofilm

The antifouling (AF) potential of the serine protease Esperase HPF (subtilisin) was evaluated for the ability to prevent the formation of a four-species bacterial biofilm. The effects of enzyme activity, time and application of the enzyme were tested on the density and the oxidative metabolism of biofilm developed in microtiter wells. Esperase HPF did not inhibit the oxidative metabolism of the bacterial biofilm or planktonic growth, but the enzyme inhibited biofilm formation by its proteolytic activity as inactivated enzyme had no effect. The effective enzyme concentration was determined over a period of 72 h, as by then all the tested concentrations inhibited biofilm formation maximally. The effective concentrations of the enzymes in solution were the same regardless of time of application (ie before or after biofilm formation), but immobilisation of the enzymes caused a lower effective concentration. Esperase HPF is an attractive alternative to the biocidal compounds used in AF coatings today.

Amphiphilic cross-linked networks produced from the vulcanization of nanodomains within thin films of poly(N-vinylpyrrolidinone)-b-poly(isoprene)

Diblock copolymers of poly(N-vinylpyrrolidinone) (PNVP) and poly(isoprene) (PIp) were employed as building blocks for the construction of complex cross-linked networks that present surfaces having amphiphilic character, imparted by covalent trapping of compositionally heterogeneous phase-separated morphologies. The kinetics for the homopolymerization of N-vinylpyrrolidinone by reversible addition-fragmentation chain transfer (RAFT) techniques was studied, and the initially obtained PNVP-based macro-RAFT agents were then extended to PNVP-b-PIp block copolymers. Therefore, the PNVP chain length was held constant at a number-averaged degree of polymerization of 120, while the PIp chain length was varied to afford a series of three PNVP120-b-PIpx block copolymers (where x=710, 53, and 25). These materials were then cross-linked individually using sulfur monochloride, to produce complex amphiphilic networks. The nanoscopically resolved topographies of these films were analyzed using atomic force microscopy, and their compositional heterogeneities were probed by X-ray photoelectron spectroscopy and internal reflectance infrared imaging techniques. Additionally, the surfaces were analyzed to determine the extent of surface reorganization under aqueous conditions.

Development and testing of hierarchically wrinkled coatings for marine antifouling

We report on the formation and testing of novel marine coatings comprising hierarchically wrinkled surface topographies (HWTS) having wrinkles of different length scales (generations) ranging from tens of nanometers to a fraction of a millimeter. The individual wrinkle generations are arranged in nested patterns, where each larger wrinkle resides underneath and represents a scaled-up version of the smaller wrinkle. We present and discuss results from field tests in seawater and laboratory experiments. The results of our field tests reveal that while coatings with flat topographies foul after relatively short time periods (4-15 weeks), the HWST coatings with the same chemistries as flat coatings remain relatively free of biofouling even after prolonged exposure to seawater (18 months). In contrast to flat coatings, the HWST substrates are not colonized by barnacles. These observations suggest that surface topography plays a dominant role in governing the coating defense against barnacle fouling even without fine-tuning the chemical composition of the overcoat. Laboratory experiments indicate that settlement of zoospores of the green alga Ulva and the strength of attachment of sporelings (young plants) depend on the chemical composition of the coating as well as surface topography.

Remarkable convergent evolution in specialized parasitic Thecostraca (Crustacea)

BACKGROUND

The Thecostraca are arguably the most morphologically and biologically variable group within the Crustacea, including both suspension feeders (Cirripedia: Thoracica and Acrothoracica) and parasitic forms (Cirripedia: Rhizocephala, Ascothoracida and Facetotecta). Similarities between the metamorphosis found in the Facetotecta and Rhizocephala suggests a common evolutionary origin, but until now no comprehensive study has looked at the basic evolution of these thecostracan groups.

RESULTS

To this end, we collected DNA sequences from three nuclear genes [18S rRNA (2,305), 28S rRNA (2,402), Histone H3 (328)] and 41 larval characters in seven facetotectans, five ascothoracidans, three acrothoracicans, 25 rhizocephalans and 39 thoracicans (ingroup) and 12 Malacostraca and 10 Copepoda (outgroup). Maximum parsimony, maximum likelihood and Bayesian analyses showed the Facetotecta, Ascothoracida and Cirripedia each as monophyletic. The better resolved and highly supported DNA maximum likelihood and morphological-DNA Bayesian analysis trees depicted the main phylogenetic relationships within the Thecostraca as (Facetotecta, (Ascothoracida, (Acrothoracica, (Rhizocephala, Thoracica)))).

CONCLUSION

Our analyses indicate a convergent evolution of the very similar and highly reduced slug-shaped stages found during metamorphosis of both the Rhizocephala and the Facetotecta. This provides a remarkable case of convergent evolution and implies that the advanced endoparasitic mode of life known from the Rhizocephala and strongly indicated for the Facetotecta had no common origin. Future analyses are needed to determine whether the most recent common ancestor of the Thecostraca was free-living or some primitive form of ectoparasite.

The effect of surface colour on the adhesion strength of Elminius modestus Darwin on a commercial non-biocidal antifouling coating at two locations in the UK

A number of factors affect the adhesion strength of organisms to fouling-release coatings, and except for a few studies focussing on black or white surfaces none have dealt specifically with the effect of coating colour. The aim was to test the effect of colour on the adhesion strength of the barnacle Elminius modestus. Panels coated in six commercial colours of Intersleek 700 were submerged at two field sites and barnacles were pushed-off using a standard assay procedure. The strength of adhesion (SOA) varied between and within sites for colour and by barnacle basal area, SOA per unit area being higher for smaller barnacles. Higher SOA with a small basal area may be because of size-specific predation, differential hydrodynamic effects or adhesive failure with age. The complex effect of colour on barnacle adhesion may be because of physico-chemical surface characteristics varying with pigments, and their interactions with local environmental conditions, as well as interactions with the settling barnacle larvae.

The relative magnitude of the effects of biological and physical settlement cues for cypris larvae of the acorn barnacle, Semibalanus balanoides L

Barnacle cypris larvae respond to many cues when selecting a settlement site. The settlement of over a million larvae on tiles of different textures, orientations and densities of incumbent settlers was measured on the rocky intertidal at Great Cumbrae, Scotland. Half of the tiles were replaced every tide whereas the others simultaneously accumulated settlers. Factor effects varied on each tide, and converged in the accumulating deployment. Increasing incumbent density led to net loss of settlement, which was less probable on the textures on which fastest settlment occurred ('very fine'), and more probable on those on which settlement was slowest ('smooth'). More settlement occurred on down-facing orientations during daylight and vice versa. Cue ranks were non-linear, so a path analysis model quantified the relative influence of each factor. Gregariousness was the most influential cue measured, although unmeasured factors had greater effects, highlighting the complexity of settlement influences in this species.

Antifouling potential of Subtilisin A immobilized onto maleic anhydride copolymer thin films

The proteinaceous nature of the adhesives used by most fouling organisms to attach to surfaces suggests that coatings incorporating proteolytic enzymes may provide a technology for the control of biofouling. In the present article, the antifouling (AF) and fouling release potential of model coatings incorporating the surface-immobilized protease, Subtilisin A, have been investigated. The enzyme was covalently attached to maleic anhydride copolymer thin films; the characteristics of the bioactive coatings obtained were adjusted through variation of the type of copolymer and the concentration of the enzyme solution used for immobilization. The bioactive coatings were tested for their effect on the settlement and adhesion strength of two major fouling species: the green alga Ulva linza and the diatom Navicula perminuta. The results show that the immobilized enzyme effectively reduced the settlement and adhesion strength of zoospores of Ulva and the adhesion strength of Navicula cells. The AF efficacy of the bioactive coatings increased with increasing enzyme surface concentration and activity, and was found to be superior to the equivalent amount of enzyme in solution. The results provide a rigorous analysis of one approach to the use of immobilized proteases to reduce the adhesion of marine fouling organisms and are of interest to those investigating enzyme-containing coating technologies for practical biofouling control.

Herbal plants as a promising source of natural antifoulants: evidence from barnacle settlement inhibition

A series comprising hexane, ethyl acetate, ethanol and aqueous extracts from six common Chinese herbs (Carpesium abrotanoides, Melia toosendan, Cnidium monnieri, Vitex negundo, Stemona sp. and Sophora flavescens) was investigated for antifouling (AF) activity against cypris (cyprids) larvae of the barnacle Balanus albicostatus. All extracts tested except the aqueous extract from Stemona sp. significantly inhibited the settlement of cyprids, the most potent being the ethyl acetate extract of S. flavescens (EC(50) value 2.08 microg ml(-1)), from which an AF compound, identified as 2'-methoxykurarinone, was isolated using bioassay-guided procedures. Furthermore, the AF activity of this compound was found to be highly reversible and greater than that of the three other natural products from S. flavescens, namely matrine, oxymatrine and oxysophocarpine. These compounds have been used commercially in China for their pharmaceutical activities, but their AF activities have not previously been evaluated. Analysis of structure-activity relationships suggested that the N-1 nitrogen atom in matrine plays a crucial role in AF activity. Overall, the present findings indicate that herbal plants are a valuable source of novel AF agents.

Nanoscale structures and mechanics of barnacle cement

Polymerized barnacle glue was studied by atomic force microscopy (AFM), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and chemical staining. Nanoscale structures exhibiting rod-shaped, globular and irregularly-shaped morphologies were observed in the bulk cement of the barnacle Amphibalanus amphitrite (=Balanus amphitrite) by AFM. SEM coupled with energy dispersive X-ray (EDX) provided chemical composition information, making evident the organic nature of the rod-shaped nanoscale structures. FTIR spectroscopy gave signatures of beta-sheet and random coil conformations. The mechanical properties of these nanoscale structures were also probed using force spectroscopy and indentation with AFM. Indentation data yielded higher elastic moduli for the rod-shaped structures when compared with the other structures in the bulk cement. Single molecule AFM force-extension curves on the matrix of the bulk cement often exhibited a periodic sawtooth-like profile, observed in both the extend and retract portions of the force curve. Rod-shaped structures stained with amyloid protein-selective dyes (Congo red and thioflavin-T) revealed that about 5% of the bulk cement were amyloids. A dominant 100 kDa cement protein was found to be mechanically agile, using repeating hydrophobic structures that apparently associate within the same protein or with neighbors, creating toughness on the 1-100 nm length scale.

Fluorinated/siloxane copolymer blends for fouling release: chemical characterisation and biological evaluation with algae and barnacles

Fouling-release coatings were prepared from blends of a fluorinated/siloxane copolymer with a poly(dimethyl siloxane) (PDMS) matrix in order to couple the low modulus character of PDMS with the low surface tension typical for fluorinated polymers. The content of the surface-active copolymer was varied in the blend over a broad range (0.15-10 wt % with respect to PDMS). X-ray photoelectron spectroscopy depth profiling analyses were performed on the coatings to establish the distribution of specific chemical constituents throughout the coatings, and proved enrichment in fluorine of the outermost layers of the coating surface. Addition of the fluorinated/siloxane copolymer to the PDMS matrix resulted in a concentration-dependent decrease in settlement of barnacle, Balanus amphitrite, cyprids. The release of young plants of Ulva, a soft fouling species, and young barnacles showed that adhesion strength on the fluorinated/siloxane copolymer was significantly lower than the siloxane control. However, differences in adhesion strength were not directly correlated with the concentration of copolymer in the blends.

Oxygen-depleted surfaces: a new antifouling technology

A novel, non-toxic strategy to combat marine biofouling is presented. The technology is paint with additions of up to 43% of industrial protein. Through microbial degradation of the protein component, an oxygen-depleted layer rapidly forms in a 0.2 mm layer close to the paint surface. With the present paint formulations, a stable, O(2)-depleted layer can persist for 16 weeks. Barnacle larvae (cyprids) did not settle on panels where oxygen saturation was <20%, and cyprids were killed when exposed to O(2)-free water for more than 1 h. It is also shown that the O(2)-depleted layer will rapidly reform (within 15 min) after exposure to turbulent flow. Field exposure of panels for 16 weeks showed that paint with protein reduced fouling by barnacles and bryozoans by 80% and close to 100%, respectively. The results suggest that this novel technology may be developed into a non-toxic alternative to copper-based antifouling paints, especially for pleasure boats in sensitive environments. There is clearly potential for further development of the paint formulation, and a full-scale test on a boat-hull suggested that service-life under realistic operations needs to be improved.

Marine biofouling field tests, settlement assay and footprint micromorphology of cyprid larvae of Balanus amphitrite on model surfaces

Atomic force microscopy (AFM), laboratory settlement assays and field tests were used to correlate cyprid footprint (FP) morphology with the behaviour of cyprids on different substrata. AFM imaging under laboratory conditions revealed more porous and larger FPs on glass exposing a CH3-surface than on aminosilane functionalised (NH2-) surfaces. The secreted FP volume was found to be similar on both substrata (2.1-2.6 microm(3)). Laboratory settlement assays and marine field tests were performed on three substrata, viz. untreated clean glass, NH2-glass, and CH3-glass. The results distinguished settlement preferences for NH2-glass and untreated glass over CH3-terminated surfaces, suggesting that cyprids favour settling on hydrophilic over hydrophobic surfaces. On combining observations from different length scales, it is speculated that the confined FP size on NH2-glass may induce a higher concentration of the settlement inducing protein complex. Settlement may be further facilitated by a stronger adherence of FP adhesives to the NH2-surface via Coulombic interactions.

Antennular sensory organs in cyprids of balanomorphan cirripedes: standardizing terminology using Megabalanus rosa

Cirripedes are one of the major groups of fouling organism in the marine environment. The cyprid can, before a permanent attachment, actively explore and walk on the substratum using its antennules in a bipedal fashion without leaving the surface. Studying the structure of the cyprid antennule is therefore important for understanding the events that culminate in biofouling by barnacles. There are at present no complete, standardised accounts of the structure of the cyprid antennules in thoracican barnacles, and moreover, the existing accounts vary in their use of terminology. This article describes the cyprid antennule of the barnacle Megabalanus rosa. This barnacle species is common in E Asia, and the cyprids have previously been used in several biofouling studies. All externally visible setae on the antennules have been mapped; these comprise both chemosensors with a terminal pore, a putative aesthetasc-like seta and mechano-sensory setae. More setae were found on the attachment disc than in previous scanning electron microscope-based studies, but not all structures that can be seen with transmission electron microscopy were visible. The disc itself seems to have a variable surface area, which could assist in exploring rough surfaces. The various lengths of the antennular setae, coupled with the disposition of the segments, enable the cyprid to cover a wide swath of substratum during exploratory walking. A new terminology is proposed for cyprid antennular setae, which will form a basis for future comparative and functional studies of cirripede settlement.

Involvement of reactive oxygen species in the electrochemical inhibition of barnacle (Amphibalanus amphitrite) settlement

The role of reactive oxygen species (ROS) in electrochemical biofouling inhibition was investigated using a series of abiotic tests and settlement experiments with larvae of the barnacle Amphibalanus amphitrite, a cosmopolitan fouler. Larval settlement, a measure of biofouling potential, was reduced from 43% +/- 14% to 5% +/- 6% upon the application of pulsed electric signals. The application of ROS scavengers such as glutathione and catalase counteracted the inhibitory effects of the electric signals, allowing settlement, and thus indicating that ROS are antifouling agents. Based on the experimental evidence, the proposed mechanism for ROS-based fouling prevention with interdigitated electrodes involved the electrochemical generation of hydrogen peroxide by oxygen reduction, and its likely reduction to hydroxyl radicals. Either hydroxyl radicals or products of hydroxyl radical reactions appeared to be the main deterrents of larval settlement.

Marine antifouling laboratory bioassays: an overview of their diversity

In aquatic environments, biofouling is a natural process of colonization of submerged surfaces, either living or artificial, involving a wide range of organisms from bacteria to invertebrates. Antifouling can be defined as preventing the attachment of organisms onto surfaces. This article reviews the laboratory bioassays that have been developed for studying the control of algae and invertebrates by epibiosis (chemical ecology) and the screening of new active compounds (natural products and biocides) to inhibit settlement or adhesion, ie fouling-release coatings. The assays utilize a range of organisms (mainly marine bacteria, diatoms, algae, barnacles). The main attributes of assays for micro- and macroorganisms are described in terms of their main characteristics and depending on the biological process assessed (growth, adhesion, toxicity, behavior). The validation of bioassays is also discussed.

In situ ATR-FTIR characterization of primary cement interfaces of the barnacle Balanus amphitrite

A method is presented for characterizing primary cement interfaces of barnacles using in situ attenuated total reflection-Fourier transform infrared spectroscopy. Primary cement of the barnacle, Balanus amphitrite (Amphibalanus amphitrite), was characterized without any disruption to the original cement interface, after settling and growing barnacles directly on double sided polished germanium wafers. High-quality IR spectra were acquired of live barnacle cement interfaces, providing a spectroscopic fingerprint of cured primary cement in vivo with the barnacle adhered to the substratum. Additional spectra were also acquired of intact cement interfaces for which the upper portion of the barnacle had been removed leaving only the base plate and cement layer attached to the substratum. This allowed further characterization of primary cement interfaces that were dried or placed in D(2)O. The resulting spectra were consistent with the cement being proteinaceous, and allowed analysis of the protein secondary structure and water content in the cement layer. The estimated secondary structure composition was primarily beta-sheet, with additional alpha-helix, turn and unordered components. The cement of live barnacles, freshly removed from seawater, was estimated to have a water content of 20-50% by weight. These results provide new insights into the chemical properties of the undisturbed barnacle adhesive interface.

Mini-review: quorum sensing in the marine environment and its relationship to biofouling

Bacterial quorum sensing (QS) is a cell-cell communication and gene regulatory mechanism that allows bacteria to coordinate swarming, biofilm formation, stress resistance, and production of toxins and secondary metabolites in response to threshold concentrations of QS signals that accumulate within a diffusion-limited environment. This review focuses on the role of QS signaling and QS inhibition in marine bacteria by compounds derived from marine organisms. Since the formation of a biofilm is considered to be an initial step in the development of fouling, direct and indirect effects of QS signals and inhibitors on the process of marine biofouling are discussed. Directions for future investigations and QS-related biotechnological applications are highlighted.