Electrical detection of spin precession in freely suspended graphene spin valves on cross-linked poly(methyl methacrylate)

Spin injection and detection is achieved in freely suspended graphene using cobalt electrodes and a nonlocal spin-valve geometry. The devices are fabricated with a single electron-beam-resist poly(methyl methacrylate) process that minimizes both the fabrication steps and the number of (aggressive) chemicals used, greatly reducing contamination and increasing the yield of high-quality, mechanically stable devices. As-grown devices can present mobilities exceeding 10(4) cm(2) V(-1) s(-1) at room temperature and, because the contacts deposited on graphene are only exposed to acetone and isopropanol, the method is compatible with almost any contacting material. Spin accumulation and spin precession are studied in these nonlocal spin valves. Fitting of Hanle spin precession data in bilayer and multilayer graphene yields a spin relaxation time of ∼125-250 ps and a spin diffusion length of 1.7-1.9 μm at room temperature.

Nanoscale interfacial friction and adhesion on supported versus suspended monolayer and multilayer graphene

Using atomic force microscopy (AFM), supported by semicontinuum numerical simulations, we determine the effect of tip-subsurface van der Waals interactions on nanoscale friction and adhesion for suspended and silicon dioxide supported graphene of varying thickness. While pull-off force measurements reveal no layer number dependence for supported graphene, suspended graphene exhibits an increase in pull-off force with thickness. Further, at low applied loads, friction increases with increasing number of layers for suspended graphene, in contrast to reported trends for supported graphene. We attribute these results to a competition between local forces that determine the deformation of the surface layer, the profile of the membrane as a whole, and van der Waals forces between the AFM tip and subsurface layers. We find that friction on supported monolayer graphene can be fit using generalized continuum mechanics models, from which we extract the work of adhesion and interfacial shear strength. In addition, we show that tip-sample adhesive forces depend on interactions with subsurface material and increase in the presence of a supporting substrate or additional graphene layers.

Fine tuning of graphene-metal adhesion by surface alloying

We show that bimetallic surface alloying provides a viable route for governing the interaction between graphene and metal through the selective choice of the elemental composition of the surface alloy. This concept is illustrated by an experimental and theoretical characterization of the properties of graphene on a model PtRu surface alloy on Ru(0001), with a concentration of Pt atoms in the first layer between 0 and 50%. The progressive increase of the Pt content determines the gradual detachment of graphene from the substrate, which results from the modification of the carbon orbital hybridization promoted by Pt. Alloying is also found to affect the morphology of graphene, which is strongly corrugated on bare Ru, but becomes flat at a Pt coverage of 50%. The method here proposed can be readily extended to several supports, thus opening the way to the conformal growth of graphene on metals and to a full tunability of the graphene-substrate interaction.

Ab initio simulation of helium-ion microscopy images: the case of suspended graphene

Helium ion microscopy (HIM), which was released in 2006 by Ward et al., provides nondestructive imaging of nanoscale objects with higher contrast than scanning electron microscopy. HIM measurement of suspended graphene under typical conditions is simulated by first-principles time-dependent density functional theory and the 30 keV He+ collision is found to induce the emission of electrons dependent on the impact point. This finding suggests the possibility of obtaining a highly accurate image of the honeycomb pattern of suspended graphene by HIM. Comparison with a simulation of He0 under the same kinetic energy shows that electron emission is governed by the impact ionization instead of Auger process initiated by neutralization of He+.

Stretchable and highly sensitive graphene-on-polymer strain sensors

The use of nanomaterials for strain sensors has attracted attention due to their unique electromechanical properties. However, nanomaterials have yet to overcome many technological obstacles and thus are not yet the preferred material for strain sensors. In this work, we investigated graphene woven fabrics (GWFs) for strain sensing. Different than graphene films, GWFs undergo significant changes in their polycrystalline structures along with high-density crack formation and propagation mechanically deformed. The electrical resistance of GWFs increases exponentially with tensile strain with gauge factors of ~10³ under 2~6% strains and ~10⁶ under higher strains that are the highest thus far reported, due to its woven mesh configuration and fracture behavior, making it an ideal structure for sensing tensile deformation by changes in strain. The main mechanism is investigated, resulting in a theoretical model that predicts very well the observed behavior.