Chromium determination and speciation since 2000

Determination of Cr(VI) and Cr(III) species in parenteral solutions using a nanostructured material packed-microcolumn and electrothermal atomic absorption spectrometry

A sequential on-line preconcentration and separation system for Cr(VI) and Cr(III) species determination was developed in this work. For this purpose, a microcolumn filled with nanostructured alpha-alumina was used for on-line retention of Cr species in a flow-injection system. The method involves the selective elution of Cr(VI) with concentrated ammonia and Cr(III) with 1mol L(-1) nitric acid for sequential injection into an electrothermal atomic absorption spectrometer (ETAAS). Analytical parameters including pH, eluent type, flow rates of sample and eluent, interfering effects, etc., were optimized. The preconcentration factors for Cr(VI) and Cr(III) were 41 and 18, respectively. The limit of detection (LOD) was 1.9 ng L(-1) for Cr(VI) and 6.1 ng L(-1) for Cr(III). The calibration graph was linear with a correlation coefficient of 0.999. The relative standard deviation (RSD) was 8.6% for Cr(VI) and 6.1% for Cr(III) (c = 10 microg L(-1), n=10, sample volume = 25 mL). Verification of the accuracy was carried out by analysis of a standard reference material (NIST SRM 1643e "Trace elements in natural water") with a reported Cr content of 20.40+/-0.24 microg L(-1). Using the proposed methodology the total Cr content, computed as sum of Cr(III) and Cr(VI), in this SRM was 20.26+/-0.96 microg L(-1). The method was successfully applied to the determination of Cr(VI) and Cr(III) species in parenteral solutions. Concentration of Cr(III) species was found to be in the range of 0.29-3.62 microg L(-1), while Cr(VI) species was not detected in the samples under study.

Speciation of chromium in water samples with cloud point extraction separation and preconcentration and determination by graphite furnace atomic absorption spectrometry

A novel method has been developed for the speciation of chromium in natural water samples based on cloud point extraction (CPE) separation and preconcentration, and determination by graphite furnace atomic absorption spectrometry (GFAAS). In this method, Cr(III) reacts with 1-phenyl-3-methyl-4-benzoylpyrazol-5-one (PMBP) yielding a hydrophobic complex, which then is entrapped in the surfactant-rich phase, whereas Cr(VI) remained in aqueous phase. Thus, separation of Cr(III) and Cr(VI) could be realized. Total chromium was determined after the reduction of Cr(VI) to Cr(III) by using ascorbic acid as reducing reagent. PMBP was used not only as chelating reagent in CPE procedure, but also as chemical modifier in GFAAS determination of chromium. The detection limit for Cr(III) was 21 ng L(-1) with an enrichment factor of 42, and the relative standard deviation was 3.5% (n=7, c=10 ng mL(-1)). The proposed method has been applied to the speciation of chromium in natural water samples with satisfactory results.

Cr(VI) and Cr(III) speciation on Bacillus sphaericus loaded diaion SP-850 resin

A speciation procedure for chromium(III) and chromium(VI) in the environmental samples has been established in the presented work. The procedure presented based on quantitative biosorption of chromium(III) on Bacillus sphaericus loaded Diaion SP-850 at pH 5. The Cr(VI) recoveries at pH 5 were below 5% on the biosorbent. After reduction of Cr(VI) by concentrated H(2)SO(4) and ethanol, the system was applied to the total chromium. Cr(VI) was calculated as the difference between the total chromium content and the Cr(III) content. Optimal analytical conditions including pH, amounts of biosorbent, etc. for Cr(III) recoveries were investigated. The influences of the some alkaline and earth alkaline ions and some transition metals on the recoveries were also investigated. The capacity of biosorbent for chromium(III) was 6.95 mgg(-1). The detection limit (3 sigma) of the reagent blank for chromium(III) was 0.50 microgL(-1). The procedure was successfully applied to the speciation of chromium(III) and chromium(VI) in natural water samples (R.S.D. lower than 5%, recoveries greater than 95%).

Validation of a European standard for the determination of hexavalent chromium in solid material

A European standard for the determination of Cr(vi) in solid material has been elaborated in the framework of an international co-operation and finally validated in the course of an interlaboratory comparison. The procedure is based on the alkaline digestion prescribed by EPA method 3060A followed by ion chromatography and determines an operationally defined content of Cr(vi), including water-soluble and insoluble chromates. A preliminary robustness study was carried out in order to compare different extraction methodologies and to study the equivalency of different analytical methods for the determination of Cr(vi) in alkaline extracts of soil and waste materials. During an interlaboratory validation trial with 19 European laboratories a set of 4 samples (2 soil and 2 waste samples) was analysed to determine performance characteristics for different combinations of digestion and detection methods. With the procedures prescribed by the new European standard (EN 15192) acceptable results were obtained for both soil samples and one of the waste samples (sludge). However, for the second waste sample (fly ash) a large deviation in analytical results was observed. This indicates that particularly for waste materials a possible occurrence of strong matrix effects has to be considered and supplementary quality control data are needed in order to assess the validity of analytical results. The accuracy of the determination of Cr(vi) in solid matrices remains a challenging field in terms of maximum extraction efficiency and minimum species interconversion.