Synthesis methods for nanosized hydroxyapatite with diverse structures

Modulated Monoclinic Hydroxyapatite: The Effect of pH in the Microwave Assisted Method

Hydroxyapatite (HAp) is a natural hard tissue constituent widely used for bone and tooth replacement engineering. In the present work, synthetic HAp was obtained from calcium nitrate tetrahydrate (Ca(NO3)2·4H2O) and ammonium phosphate dibasic (NH4)2HPO4 following an optimized microwave assisted hydrothermal method. The effect of pH was evaluated by the addition of ammonium hydroxide (NH4OH). Hence, different characterization techniques were used to determine its influence on the resulted HAp powders’ size, shape, and crystallinity. By Transmission Electron Microscopy (TEM), it was observed that the reaction pH environment modifies the morphology of HAp, and a shape evolution, from sub-hedral particles at pH = 7 to rod-like nanosized HAp at pH = 10, was confirmed. Using the X-ray Diffraction (XRD) technique, the characteristic diffraction peaks of the monoclinic phase were identified. Even if the performed Rietveld analysis indicated the presence of both phases (hexagonal and monoclinic), monoclinic HAp prevails in 95% with an average crystallite size of about 23 nm. The infrared spectra (FTIR) showed absorption bands at 3468 cm−1 and 630 cm−1 associated with OH− of hydroxyapatite, and bands at 584 cm−1, 960 cm−1, and 1090 cm−1 that correspond to the PO43− and CO32− characteristic groups. In summary, this work contributes to obtaining nanosized rod-like monoclinic HAp by a simple and soft method that has not been previously reported.

A review on adsorptive removal of dyes from wastewater by hydroxyapatite nanocomposites

Dye removal from wastewater is of prominence due to its hostile effects on human health and the environment. The complex structure of the dye molecule is responsible for its difficulty in removal. Adsorption is found to be a promising technique to eliminate dye wastes due to its high removal capacity at low concentration. Among different adsorbents used, hydroxyapatite is a biocompatible adsorbent that is relatively efficient in both anionic and cationic dye removal. Recently, modification of hydroxyapatite by doping with other materials to increase its removal efficiency has gained much attention. This review summarizes compilation of recent literature on the removal of anionic and cationic dye by different hydroxyapatite nanocomposites, comparison of adsorption capacities of different hydroxyapatite nanocomposites, the possible adsorption mechanism of removal of dyes, the general isotherm, and kinetic and thermodynamic studies explaining the type of adsorption and the characteristics, advantages, and limitations of adsorbents.

Rolled-Up Metal Oxide Microscaffolds to Study Early Bone Formation at Single Cell Resolution

Titanium and its alloys are frequently used to replace structural components of the human body due to their high mechanical strength, low stiffness, and biocompatibility. In particular, the use of porous materials has improved implant stabilization and the promotion of bone. However, it remains unclear which material properties and geometrical cues are optimal for a proper osteoinduction and osseointegration. To that end, transparent tubular microscaffolds are fabricated, mimicking the typical pores of structural implants, with the aim of studying early bone formation and cell-material interactions at the single cell level. Here, a β-stabilized alloy Ti-45Nb (wt%) is used for the microscaffold's fabrication due to its elastic modulus close to that of natural bone. Human mesenchymal stem cell migration, adhesion, and osteogenic differentiation is thus investigated, paying particular attention to the CaP formation and cell-body crystallization, both analyzed via optical and electron microscopy. It is demonstrated that the developed platform is suited for the long-term study of living single cells in an appropriate microenvironment, obtaining in the process deeper insights on early bone formation and providing cues to improve the stability and biocompatibility of current structural implants.

Solid-Supported Amplification of Aggregation Emission: A Tetraphenylethylene-Cucurbit[6]uril@Hydroxyapatite-Based Supramolecular Sensing Assembly for the Detection of Spermine and Spermidine in Human Urine and Blood

The development of sensitive and selective tools for the detection and quantification of biomarkers is important in the diagnosis and treatment of clinical diseases. Spermine (SP) and spermidine (SPD) act as biomarkers for early-stage diagnosis of cancer in humans as their increased levels in urine are indicative of abnormal biological processes associated with this fatal disease. In this study, we introduced a strategy for solid-supported amplification of the effective aggregation-induced-emission (AIE) effect of a water-soluble tetraphenylethylene (TPE)-based probe in developing a supramolecular sensing platform for the rapid, sensitive, and selective detection of SP and SPD in water. The nonemissive TPE derivative (TPEHP) forms a less emissive conjugate with hydroxyl cucurbit[6]uril (CB[6]OH) in water, which undergoes several-fold enhancement of effective emission upon electrostatic interaction with the solid surface of hydroxyapatite nanoparticles (HAp NPs), dispersed in the aqueous media. The corresponding three-component supramolecular assembly disrupts by the intrusion of SP and SPD in the CB[6] portal because of the stronger binding ability with CB[6], resulting in a turn-off fluorescence sensor for SP and SPD with enhanced sensitivity. The assembly-disassembly-based sensing mechanism was thoroughly demonstrated by carrying out isothermal titration calorimetry (ITC), spectroscopic, and microscopic experiments. The sensing system showed low limits of detection (LODs) of 1.4 × 10^-8 and 3.6 × 10^-8 M for SP and SPD, respectively, which are well below the required range for the early diagnosis of cancer. Besides, a good linear relationship was obtained for both SP and SPD. Nominal interference from various metal ions, anions, common chemicals, amino acids, and other biogenic amines makes this sensing platform suitable for the real-time, low-level measurement of spermine (and spermidine) in human urinary and blood samples.

Biomaterial-Based Nanocomposite for Osteogenic Repurposing of Doxycycline

Background

Besides its antimicrobial action, doxycycline (DX) has lately been repurposed as a small-molecule drug for osteogenic purposes. However, osteogenic DX application is impeded by its dose-dependent cytotoxicity. Further, high-dose DX impairs cell differentiation and mineralization.

Purpose

Integrating DX into a biomaterial-based delivery system that can control its release would not only ameliorate its cytotoxic actions but also augment its osteogenic activity. In this work, we managed to engineer novel composite DX–hydroxyapatite–polycaprolactone nanoparticles (DX/HAp/PCL) to modify DX osteogenic potential.

Methods

Employing a 2³-factorial design, we first optimized HApN for surface-area attributes to maximize DX loading. Composite DX/HAp/PCL were then realized using a simple emulsification technique, characterized using various in vitro methods, and evaluated for in vitro osteogenesis.

Results

The developed HApN exhibited a favorable crystalline structure, Ca:P elemental ratio (1.67), mesoporous nature, and large surface area. DX/HAp/PCL achieved the highest reported entrapment efficiency (94.77%±1.23%) of DX in PCL-based particles. The developed composite system achieved controlled release of the water-soluble DX over 24 days. Moreover, the novel composite nanosystem managed to significantly ameliorate DX cytotoxicity on bone-marrow stem cells, as well as enhance its overall proliferation potential. Alkaline phosphatase and mineralization assays revealed superior osteodifferentiation potential of the composite system. Quantification of gene expression demonstrated that while DX solution was able to drive bone-marrow stem cells down the osteogenic lineage into immature osteoblasts after 10-day culture, the innovative composite system allowed maturation of osteodifferentiated cells. To the best of our knowledge, this is the first work to elaborate the impact of DX on the expression of osteogenic genes: RUNX2, OSP, and BSP. Further, the osteogenicity of a DX-loaded particulate-delivery system has not been previously investigated.

Conclusion

Our findings indicate that repurposing low-dose DX in complementary biomaterial-based nanosystems can offer a prominent osteogenic candidate for bone-regeneration purposes.

Transition Metal Exchanged Hydroxyapatite/Fluorapatite Catalysts for C-C and C-N Bond Forming Reactions

Transition metal (Cu, Zn, Rh, Pd) exchanged hydroxyapatite (HAP)/fluorapatite (FAP) materials have been synthesized by ion-exchange method resulting in incorporation of the metal ions in the HAP/FAP structure. C-C and C-N bond forming reactions are important in synthetic organic chemistry as these organic transformations are very critical. Transition metal exchanged FAP provides an efficient catalytic system for N-arylation of haloarenes and Suzuki and Heck coupling of haloarenes. By designing such catalytic materials, our group has developed synthetic methods which allow higher product yields and easy separation with the use of a small amount of catalyst in a shorter reaction time. This account addresses the work carried out in last two decades in the area of C-C and C-N bond forming reactions using transition metal exchanged fluorapatite.

Applications of Vibrational Spectroscopy for Analysis of Connective Tissues

Advances in vibrational spectroscopy have propelled new insights into the molecular composition and structure of biological tissues. In this review, we discuss common modalities and techniques of vibrational spectroscopy, and present key examples to illustrate how they have been applied to enrich the assessment of connective tissues. In particular, we focus on applications of Fourier transform infrared (FTIR), near infrared (NIR) and Raman spectroscopy to assess cartilage and bone properties. We present strengths and limitations of each approach and discuss how the combination of spectrometers with microscopes (hyperspectral imaging) and fiber optic probes have greatly advanced their biomedical applications. We show how these modalities may be used to evaluate virtually any type of sample (ex vivo, in situ or in vivo) and how "spectral fingerprints" can be interpreted to quantify outcomes related to tissue composition and quality. We highlight the unparalleled advantage of vibrational spectroscopy as a label-free and often nondestructive approach to assess properties of the extracellular matrix (ECM) associated with normal, developing, aging, pathological and treated tissues. We believe this review will assist readers not only in better understanding applications of FTIR, NIR and Raman spectroscopy, but also in implementing these approaches for their own research projects.

Dual Stimuli-Responsive Pickering Emulsions from Novel Magnetic Hydroxyapatite Nanoparticles and Their Characterization Using a Microfluidic Platform

Stimuli-responsive emulsifiers have emerged as a class of smart agents that can permit regulated stabilization and destabilization of emulsions, which is essential for food, cosmetic, pharmaceutical, and petroleum industries. Here, we report the synthesis of novel "smart" hydroxyapatite (HaP) magnetic nanoparticles and their corresponding stimuli-responsive Pickering emulsions and explore their movement under confined spaces using a microfluidic platform. Pickering emulsions prepared with our magnetic stearic acid-functionalized Fe₂O₃@HaP nanoparticles exhibited pronounced pH-responsive behavior. We observed that the diameter of emulsion droplets decreases with an increase in pH. Swift demulsification was achieved by lowering the pH, whereas the reformation of emulsions was achieved by increasing the pH; this emulsification-demulsification cycling was successful for at least ten cycles. We used a microfluidic platform to test the stability of the emulsions under flowing conditions and their response to a magnetic field. We observed that the emulsion stability was diminished and droplet coalescence was enhanced by the application of the magnetic field. The smart nanoparticles we developed and their HaP-based emulsions present promising materials for pharmaceutical and petroleum industries, where responsive emulsions with controlled stabilities are required.

Hybrid bioactive hydroxyapatite/polycaprolactone nanoparticles for enhanced osteogenesis

Hydroxyapatite nanoparticles (HApN) are largely employed as osteogenic inorganic material. Inorganic/polymeric hybrid nanostructures can provide versatile bioactivity for superior osteogenicity, particularly as nanoparticles. Herein, we present hybrid biomaterial-based hydroxyapatite/polycaprolactone nanoparticles (HAp/PCL NPs) realized using simple preparation techniques to augment HApN osteogenicity. Using wet chemical precipitation, we optimized HApN crystalline properties utilizing a 2³-factorial design. Optimized HApN exhibited typical Ca/P elemental ratio with high reaction yield. Surface area analysis revealed their mesoporous nature and high surface area. Hybrid HAp/PCL NPs prepared using direct emulsification-solvent evaporation maintained HApN crystallinity with no observed chemical interactions. To the best of our knowledge, we are the first to elaborate the biocompatibility and osteogenicity of nanoparticulate hybrid HAp/PCL. Hybrid HAp/PCL NPs outperformed HApN regarding mesenchymal cell proliferation and osteodifferentiation with reduction of possible cytotoxicity. Unlike HApN, hybrid HAp/PCL NPs presented moderate expression of early osteogenic markers, Runx-2 and osteopontin and significantly elevated expression of the late osteogenic marker, bone sialoprotein after 10-day culture. Our results indicate that hybrid bioactive HAp/PCL NPs could offer a more prominent osteogenic potential than plain HApN for bone regenerative applications as a standalone nanoplatform or as part of complex engineered systems.

Luminescent net-like inorganic scaffolds with europium-doped hydroxyapatite for enhanced bone reconstruction

Bone reconstruction is an urgent problem during clinical treatment. In the past few decades, the construction of composite scaffolds has been a hot spot in the research field of bone tissue engineering (BTE). However, the disadvantages of composite materials raise our awareness to explore the potential application of hydroxyapatite (HAp) in bone substitutes due to the closest properties of HAp to natural bone tissue. In our study, we synthesized Eu³⁺-doped HAp (HAp:Eu³⁺) ultralong nanowires, which can be transformed to hydrophilic net-like scaffolds via a thiol-ene click reaction. The property of luminescence of HAp from Eu³⁺ is beneficial for identifying the relative position of materials and bone marrow mesenchymal stem cells (BMSCs). HAp:Eu³⁺ scaffolds with excellent cell biocompatibility could promote the expression of early bone formation markers (ALP and ARS) and enhance the expression of genes and proteins associated with osteogenesis (Runx 2, OCN, and OPN). In the end, the results of the in vivo osteogenesis experiment showed that pure HAp scaffolds presented different effects of bone tissue reconstruction compared with the composite scaffolds with HAp nanorods and polymer materials. The superior osteogenic effect could be observed in net-like pure HAp scaffold groups. Furthermore, the absorption of HAp:Eu³⁺ scaffolds could be monitored due to the luminescence property of Eu³⁺. This strategy based on ultralong HAp nanowires proved to be a new method for the construction of simple reticular scaffolds for potential osteogenic applications.

Investigation of various fatty acid surfactants on the microstructure of flexible hydroxyapatite nanofibers

The synthesis of hydroxyapatite nanofibers using various fatty acids and their influences on HA crystal characteristics were systematically explored.

Investigation on [OH−]-responsive systems for construction of one-dimensional hydroxyapatite via a solvothermal method

The concentration of OH⁻ can directly influence the crystal growth of flexible hydroxyapatite nanofibers in oleic acid-assisted solvothermal reaction systems.

Synthetic Polymeric Materials for Bone Replacement

Some treatment options available to repair bone defects are the use of autogenous and allogeneic bone grafts. The drawback of the first one is the donor site’s limitation and the need for a second operation on the same patient. In the allograft method, the problems are associated with transmitted diseases and high susceptibility to rejection. As an alternative to biological grafts, polymers can be used in bone repair. Some polymers used in the orthopedic field are poly(methyl methacrylate), poly(ether-ether-ketone), and ultra-high molecular weight polyethylene (UHMWPE). UHMWPE has drawn much attention since it combines low friction coefficient and high wear and impact resistance. However, UHMWPE is a bioinert material, which means that it does not interact with the bone tissue. UHMWPE composites and nanocomposites with hydroxyapatite (HA) are widely studied in the literature to mitigate these issues. HA is the main component of the inorganic phase in the natural bone, and the addition of this bioactive filler to the polymeric matrix aims to mimic bone composition. This brief review discusses some polymers used in orthopedic applications, focusing on the UHMWPE/HA composites as a potential bone substitute.

Current Challenges and Innovative Developments in Hydroxyapatite-Based Coatings on Metallic Materials for Bone Implantation: A Review

Biomaterials are in use for the replacement and reconstruction of several tissues and organs as treatment and enhancement. Metallic, organic, and composites are some of the common materials currently in practice. Metallic materials contribute a big share of their mechanical strength and resistance to corrosion properties, while organic polymeric materials stand high due to their biocompatibility, biodegradability, and natural availability. To enhance the biocompatibility of these metals and alloys, coatings are frequently applied. Organic polymeric materials and ceramics are extensively utilized for this purpose due to their outstanding characteristics of biocompatibility and biodegradability. Hydroxyapatite (HAp) is the material from the ceramic class which is an ultimate candidate for coating on these metals for biomedical applications. HAp possesses similar chemical and structural characteristics to normal human bone. Due to the bioactivity and biocompatibility of HAp, it is used for bone implants for regenerating bone tissues. This review covers an extensive study of the development of HAp coatings specifically for the orthopaedic applications that include different coating techniques and the process parameters of these coating techniques. Additionally, the future direction and challenges have been also discussed briefly in this review, including the coating of HAp in combination with other calcium magnesium phosphates that occur naturally in human bone.

Low-Temperature Hydrothermal Treatment Surface Functionalization of the Ultrafine-Grained TiMo Alloys for Medical Applications

Hydroxyapatite (HAp) is the most widely used material for bio coating. The functional layer can be produced by many methods, however, the most perspective by its utility, easy to scale up, and simplicity aspects remains a hydrothermal treatment approach. In this work, an HAp coating was produced by low-temperature hydrothermal treatment on the ultrafine-grain beta Ti-xMo (x = 23, 27, 35 wt.%) alloys. The proposed surface treatment procedure combines acid etching, alkaline treatment (AT), and finally hydrothermal treatment (HT). The uniqueness of the approach relies on the recognition of the influence of the molar concentration of NaOH (5 M, 7 M, 10 M, 12 M) during the alkaline treatment on the growth of hydroxyapatite crystals. Obtained and modified specimens were examined structurally and microstructurally at every stage of the process. The results show that the layer after AT consist of titanium oxide and phases based on sodium with various phase relations dependent on NaOH concentration and base composition. The AT in 7 M and 10 M enables to obtain the HAp layer, which can be characterized as the most developed in terms of thickness and porosity. Finally, selected coated samples were investigated in terms of surface wettability test managed in time relation, which for the results confirm high hydrophilicity of the surfaces. Conducted research shows that the low-temperature hydrothermal processing could be considered for a possible adaptation in the drug encapsulation and delivery systems.

Nanostructured Carbonated Hydroxyapatite Associated to rhBMP-2 Improves Bone Repair in Rat Calvaria

Many biomaterials are used for Bone Morphogenetic Proteins (BMPs) delivery in bone tissue engineering. The BMP carrier system's primary function is to hold these growth factors at the wound's site for a prolonged time and provide initial support for cells to attach and elaborate the extracellular matrix for bone regeneration. This study aimed to evaluate the nanostructured carbonated hydroxyapatite microspheres (nCHA) as an rhBMP-2 carrier on rats calvaria. A total of fifteen male Wistar rats were randomly divided into three groups (n = 5): clot (control group), rhBMP-2 associated with collagen membrane (COL/rhBMP-2) or associated with the microspheres (nCHA/rhBMP-2). After 45 days, the calvaria defect samples were evaluated through histological, histomorphometric, and SR-µCT analyses to investigate new-formed bone and connective tissue volume densities. The descriptive histological analysis showed that nCHA/rhBMP-2 improved bone formation compared to other groups. These results were confirmed by histomorphometric and SR-µCT analysis that showed substantially defect area filling with a higher percentage of newly formed (36.24 ± 6.68) bone than those with the COL/rhBMP-2 (0.42 ± 0.40) and Clot (3.84 ± 4.57) (p < 0.05). The results showed that nCHA is an effective carrier for rhBMP-2 encouraging bone healing and an efficient alternative to collagen membrane for rhBMP-2 delivery.

Biphasic composite of calcium phosphate-based mesoporous silica as a novel bone drug delivery system

We reported the new biphasic composites of calcium phosphate and mesoporous silica material (CaP@MSi) in the form of powders and pellets as a potential bone drug delivery system for doxycycline hydrochloride (DOX). The CaP@MSi powders were synthesized by cationic surfactant-templating method. The effects of 10, 20, and 30% CaP content in the CaP@MSi powders on the molecular surface structure, the cytotoxicity against osteoblast cells in vitro, and the mineralization potential in simulated body fluid were investigated. The CaP@MSi characterized by the highest mineralization potential (30% CaP content) were used for DOX adsorption and pelletization process. The CaP which precipitated in the CaP@MSi composites was characterized as calcium-deficient with the Ca:P molar ratio between 1.0 and 1.2. The cytotoxicity assays demonstrated that the CaP content in MSi increases osteoblasts viability indicating the CaP@MSi (30% CaP content) as the most biocompatible. The combination of CaP and MSi was an effective strategy to improve the mineralization potential of parent material. Upon immersion in simulated body fluid, the CaP of composite converted into the bone-like apatite. The obtained pellets preserved the mineralization potential of CaP@MSi and provided the prolonged 5-day DOX release. The obtained biphasic CaP@MSi composites seem to have an application potential as bone-specific drug delivery system.

A plant-mediated synthesis of nanostructured hydroxyapatite for biomedical applications: a review

The engineering of calcium-based phosphate materials at the nanoscale gains several unique properties compared to the bulky state. The effort to scale down, e.g., from bulky state to nanoscale in order to control the morphology and improve structural properties requires the use of varying reagents that can be detrimental to the environment. A typical example of these materials is hydroxyapatite (HAp), one of the well-known calcium phosphate materials, which has a close resemblance to human bone tissue. HAp has valuable applications in catalysis, drug delivery, bone and dental implant formation, and adsorption. Hydroxyapatite-based nanomaterials synthesized through conventional routes make use of reagents that are not environmental friendly and are very costly. Since the current research trends are geared towards producing/synthesizing nanomaterials through an eco-friendly approach, there is the need to consider the techniques and reagents involved in the synthesis of HAp. This review touches on the possible replacement of such synthetic chemical reagents, synthesis routes, and toxic capping agents with plant extracts for synthesizing HAp-based nanomaterials for multi-functional applications. The influence of biomolecules from plants on synthesized HAps and the attainable mechanism during these green approaches are discussed. Viable future modifications of the methods used to obtain extracts from plants are also studied.

Synthesis and characterization of PLGA/HAP scaffolds with DNA-functionalised calcium phosphate nanoparticles for bone tissue engineering

Porous scaffolds of poly(lactide-co-glycolide) (PLGA; 85:15) and nano-hydroxyapatite (nHAP) were prepared by an emulsion-precipitation procedure from uniform PLGA-nHAP spheres (150-250 µm diameter). These spheres were then thermally sintered at 83 °C to porous scaffolds that can serve for bone tissue engineering or for bone substitution. The base materials PLGA and nHAP and the PLGA-nHAP scaffolds were extensively characterized by X-ray powder diffraction, infrared spectroscopy, thermogravimetry, differential scanning calorimetry, and scanning electron microscopy. The scaffold porosity was about 50 vol% as determined by relating mass and volume of the scaffolds, together with the computed density of the solid phase (PLGA-nHAP). The cultivation of HeLa cells demonstrated their high cytocompatibility. In combination with DNA-loaded calcium phosphate nanoparticles, they showed a good activity of gene transfection with enhanced green fluorescent protein (EGFP) as model protein. This is expected enhance bone growth around an implanted scaffold or inside a scaffold for tissue engineering.

L-histidine controls the hydroxyapatite mineralization with plate-like morphology: Effect of concentration and media

Hydroxyapatite (HA) is the main inorganic component of bone and dentin, and their non-stoichiometric compositions and plate-shaped morphology is responsible for their bioactivity and osteoconductive nature. Collagenous (CPs) and non-collagenous proteins (NCPs) facilitate mineralization and regulate structural properties of HA through their side-chains. The bioactivity of synthetic HA does not usually match with the HA found in bone and, therefore, there is a need to understand the role of biomolecules in bone mineralization in order to develop non-stoichiometric plate-shaped HA for bone grafts. Role of several amino acids has been investigated but the role of L-his has been rarely investigated under physiological conditions even though it is a part of HA inhibitor proteins, like albumin, amelogenin, and histidine-rich proteins. In this study, L-his and L-glu were used to modify the structural properties of HA in different experimental conditions and buffer systems (tris and hepes). The results showed that L-his was able to regulate the plate-shaped morphology of HA in every experimental condition, unlike the L-glu, where the crystal morphology was regulated by experimental conditions. Both amino acids behaved differently in DI water, tris, and hepes buffer, and the media used influenced the precipitation time and structural properties of HA. Hepes and tris buffers also influenced the HA precipitation process. Overall, the studies revealed that L-his may be used as an effective regulator of plate-shaped morphology of HA, instead of large NCPs/proteins, for designing biomaterials for bone regeneration applications and the choice of buffer system is important in designing and evaluating the systems for mineralization. In cell culture studies, mouse osteoblast precursor cells (MC3T3-E1) showed highest proliferation on the bone-like plate-shaped HA, among all the HA samples investigated.

Non-aqueous liquid crystals of hydroxyapatite nanorods

Hydroxyapatite (HA) nanorods in the collagen matrix of bone have a macroscopically ordered structure that has many similarities to the ordered structure of anisotropic nano-units in inorganic liquid crystals (LCs). Inspired by these similarities, we conducted the first (to our best knowledge) synthesis of HA LCs in non-polar solvents (such as cyclohexane and toluene), thus expanding the range of applicable monomers and polymers. We synthesized HA nanorods by a simple, effective, and oleic-acid-assisted hydrothermal route. The hydrothermal temperature directly modulates the aspect ratio of the HA nanorods, and indirectly modulates their LC behavior. The LC phase transition has no size limitation. Thus, our approach may be used to develop high solid content, macroscopically assembled, large-scale polymer-based bio(mimetic)-materials.

The Influence of Ozonated Olive Oil-Loaded and Copper-Doped Nanohydroxyapatites on Planktonic Forms of Microorganisms

The research has been carried out with a focus on the assessment of the antimicrobial efficacy of pure nanohydroxyapatite, Cu²⁺-doped nanohydroxyapatite, ozonated olive oil-loaded nanohydroxyapatite, and Cu²⁺-doped nanohydroxyapatite, respectively. Their potential antimicrobial activity was investigated against Streptococcus mutans, Lactobacillus rhamnosus, and Candida albicans. Among all tested materials, the highest efficacy was observed in terms of ozonated olive oil. The studies were performed using an Ultraviolet–Visible spectrophotometry (UV-Vis), electron microscopy, and statistical methods, by determining the value of Colony-Forming Units (CFU/mL) and Minimal Inhibitory Concentration (MIC).

Interplay between surface chemistry and osteogenic behaviour of sulphate substituted nano-hydroxyapatite

Surface potential and chemical compositions of the bioceramics are the core of therapeutic effect and are key factors to trigger the interfacial interactions with surrounding hard and soft tissues to repair and regeneration. Ionic substitution in hydroxyapatite (Hap) lattice significantly influences the zeta potential from -16.46 ± 0.66 mV to -6.01 ± 0.68 mV as well as an average nano-rod length from ~40 nm to ~26 nm with respect to SO₄^2- ion content. Moreover, the surface chemistry of Hap is mainly inter-related to SO₄^2- substitution rate at PO₄^2- site. Specifically, nano-sized feature with lowered negative surface potential influences the protein adsorption via their weak repulsive or attractive forces. Bovine serum albumin (BSA) and lysozyme (LSZ) adsorption studies confirmed the increased affinity to active binding sites of Hap's surface. Further, SO₄^2- ion substituted Hap (SNHA) showed improved in vitro biomineralization activity and alkaline phosphatase activity. Expression of osteogenic biomarkers such as collagen I, V, osteopontin and osteocalcin were evaluated in Saos-2 and MC3T3-E1 cells. Gene expression of these markers was influenced by SO₄^2- ion content in Hap (maximum with 10SNHA). Altogether, these data emphasizes that chemical composition and surface properties are dominant aspect in bioceramic development towards bone regeneration.

Hydroxyapatite extraction from fish scales of Tilapia

Hydroxyapatite is the inorganic component of human bones. To be used for bone replacements, hydroxyapatite can be synthesized or extracted from natural components. In this work we present the hydroxyapatite extraction from fish scales of the same Orechromis family (Tilapia) but from two different species usually consumed in Mexico and in Spain. Our results indicate, for both species, that it is possible to obtain hydroxyapatite, and moreover, that this biomaterial is enriched with magnesium for the Mexican Oreochromis hunteri, and with aluminum for the Spanish Oreochromis niloticus.

Nano-needle strontium-substituted apatite coating enhances osteoporotic osseointegration through promoting osteogenesis and inhibiting osteoclastogenesis

Implant loosening remains a major clinical challenge for osteoporotic patients. This is because osteoclastic bone resorption rate is higher than osteoblastic bone formation rate in the case of osteoporosis, which results in poor bone repair. Strontium (Sr) has been widely accepted as an anti-osteoporosis element. In this study, we fabricated a series of apatite and Sr-substituted apatite coatings via electrochemical deposition under different acidic conditions. The results showed that Ca and Sr exhibited different mineralization behaviors. The main mineralization products for Ca were CaHPO₄·2H₂O and Ca₃(PO₄)₂ with the structure changed from porous to spherical as the pH values increased. The main mineralization products for Sr were SrHPO₄ and Sr₅(PO₄)₃OH with the structure changed from flake to needle as the pH values increased. The in vitro experiment demonstrated that coatings fabricated at high pH condition with the presence of Sr were favorable to MSCs adhesion, spreading, proliferation, and osteogenic differentiation. In addition, Sr-substituted apatite coatings could evidently inhibit osteoclast differentiation and fusion. Moreover, the in vivo study indicated that nano-needle like Sr-substituted apatite coating could suppress osteoclastic activity, improve new bone formation, and enhance bone-implant integration. This study provided a new theoretical guidance for implant coating design and the fabricated Sr-substituted coating might have potential applications for osteoporotic patients.

∙

Ca²⁺ and Sr²⁺ showed different mineralization behaviors in acidic environments.

•

Apatites fabricated at high pH conditions were beneficial to MSCs growth.

•

Sr-substituted apatite exhibited superior anti-osteoclast activity ability.

•

Sr-substituted apatite facilitated osteogenesis, bone growth, and osseointegration.

Combination of nano-hydroxyapatite and curcumin in a biopolymer blend matrix: Characteristics and drug release performance of fibrous composite material systems

The design of appropriate materials is required for biomedical applications (e.g. drug delivery systems) in improving people's health care processes. This study focused on the incorporation of nanosized hydroxyapatite (n-HA) with different ratios (ranging from 0.1 wt% to 0.5 wt%) into the poly (ε-caprolactone)/ poly (ethylene oxide) (PCL/PEO) blend matrix loaded or unloaded with curcumin. Composite fibrous material systems were successfully fabricated by the electrospinning technique without the occurrence of bead defects. In addition to the morphological and physicochemical properties of the material systems obtained, the in vitro curcumin release performance was investigated. Further, anti-cancer activity against breast cancer cell line (MCF-7) was examined by MTT assay. Fourier transform infrared spectroscopy and X-ray diffraction characterizations of the fabricated fibrous materials exhibited the interaction of PCL/PEO, n-HA, and curcumin. The 0.3 wt% n-HA incorporated fibrous materials showed a much slower curcumin release manner along with the highest cytotoxicity against MCF-7 cells. The findings obtained from this research are expected to contribute to the appropriate design of nanofiber-based composite materials not only for drug delivery systems but also for the fabrication of biomaterials toward different biomedical applications.

Apatite matrix substituted with biologically essential rare earth elements as an artificial hard tissue substitute: Systematic physicochemical and biological evaluation

Hydroxyapatite (HAP) forms the main inorganic component of natural bone and hence has been widely use in implant applications. Ionic substitutions in apatite also gains enormous interest during the recent years due to the crucial role played by these elements in the biological process. In this context, the least investigated elements namely lanthanum (La³⁺ ) and praseodymium (Pr³⁺ ) have been selected as a potential substitutions in apatite. The results from the analytical techniques confirm the phase purity of the HAP and its ability holds the substitutions at its lattice. Morphological analysis unveils the presence of agglomerated spheroids notwithstanding the ion concentration of substituents. EDX spectra affirm the presence of La and Pr alongside the determined Ca/P atomic ratio of 1.67. La³⁺ and Pr³⁺ presence envisaged the good antibacterial efficiency against the tested microbes and further demonstrated the biocompatibility nature from the cytotoxicity analysis.

Mono-dispersed nano-hydroxyapatite based MRI probe with tetrahedral DNA nanostructures modification for in vitro tumor cell imaging

Taking advantage of the superior biocompatibility, good stability in a wide pH and temperature range, as well as its strong affinity with DNA of hydroxyapatite (HAp), tetrahedral DNA nanostructures (TDNs) conjugated with AS1411 aptamer (anti-nucleolin overexpressed on tumor cell membranes) were employed as affinity ligands to construct a novel mono-dispersed HAp based probe with Gd³⁺ doping (Apt-TDNs-GdHAp) for MR imaging. The adsorption of TDNs on the nano-HAp surface facilely accomplished the construction of the Apt-TDNs-GdHAp probes. Meanwhile, the use of hydrophilic TDNs not only favored the phase-transfer from the oil phase to the aqueous phase, but also enhanced the mono-dispersion of this probe due to the well-ordered distribution of TDNs on the surface of nano-HAp. Moreover, Apt-TDNs-GdHAp probe with a better mono-dispersion and crystalinity achieved twice higher longitudinal relaxivity (r₁ value) than that of GdHAp synthesized by microwave-assisted method (Microwave-GdHAp), exhibiting much more excellent T₁-weighted imaging performance. With the introduction of TDNs, the stability and the tumor-targeting accessibility were also greatly improved, showing its great potential for further bio-applications.

Biofilms of cellulose and hydroxyapatite composites: Alternative synthesis process

A new biofilm of cellulose coated with hydroxyapatite particles have been prepared using a simple, fast and low temperature process based on a microwave-assisted hydrothermal synthesis. The cellulose used as matrix of the biocomposite was extracted from banana stems residues. The hydroxyapatite coating was performed using calcium nitrate tetrahydrate, phosphoric acid, and 1,2-ethylenediamine dispersed in a cellulose/water solution, with posterior microwave-assisted hydrothermal synthesis, for 5 min at 140°C. The chemical, structural, thermal, and morphological properties of the composites were investigated by X-ray diffraction, infrared spectroscopy, thermogravimetry and field emission scanning electron microscopy. Results showed that the methodology was effective to produce high quality composites, with good thermal stability. Cell viability tests indicated that the cellulose/Hap films were not cytotoxic.

Nanostructured Biomaterials for Bone Regeneration

This review article addresses the various aspects of nano-biomaterials used in or being pursued for the purpose of promoting bone regeneration. In the last decade, significant growth in the fields of polymer sciences, nanotechnology, and biotechnology has resulted in the development of new nano-biomaterials. These are extensively explored as drug delivery carriers and as implantable devices. At the interface of nanomaterials and biological systems, the organic and synthetic worlds have merged over the past two decades, forming a new scientific field incorporating nano-material design for biological applications. For this field to evolve, there is a need to understand the dynamic forces and molecular components that shape these interactions and influence function, while also considering safety. While there is still much to learn about the bio-physicochemical interactions at the interface, we are at a point where pockets of accumulated knowledge can provide a conceptual framework to guide further exploration and inform future product development. This review is intended as a resource for academics, scientists, and physicians working in the field of orthopedics and bone repair.

Comparison of complications in cranioplasty with various materials: a systematic review and meta-analysis

Objective: Meta-analysis to evaluate complications in the use of autogenous bone and bone substitutes and to compare bone substitutes, specifically HA, polyetheretherketone (PEEK) and titanium materials.Methods: Search of PubMed, Cochrane, Embase and Google scholar to identify all citations from 2010 to 2019 reporting complications regarding materials used in cranioplasty.Results: 20 of 2266 articles met the inclusion criteria, including a total of 2913 patients. The odds of overall complication were significantly higher in the autogenous bone group (n = 214/644 procedures, 33.2%) than the bone substitute groups (n = 116/436 procedures, 26.7%, CI 1.29-2.35, p < 0.05). In bone substitutes groups, there was no significant difference in overall complication rate between HA and Ti (OR, 1.2; 95% CI, 0.47-3.14, p = 0.69). PEEK has lower overall complication rates (OR, 0.51; 95% CI, 0.30-0.87, p = 0.01) and lower implant exposure rates (OR, 0.17; 95% CI, 0.06-0.53, p = 0.002) than Ti, but there was no significant difference in infection rates and postoperative hematoma rates.Conclusions: Cranioplasty is associated with high overall complication rates with the use of autologous bone grafts compared with bone substitutes. PEEK has a relatively low overall complication rates in substitutes groups, but still high infection rates and postoperative hematoma rates. Thus, autologous bone grafts should only be used selectively, and prospective long-term studies are needed to further refine a better material in cranioplasty.

A pH-sensitive fluorescent protein sensor to follow the pathway of calcium phosphate nanoparticles into cells

Calcium phosphate nanoparticles (100 nm) were fluorescently labelled with poly(ethyleneimine) (PEI_ATTO490LS; red fluorescence). They were loaded with a Tandem fusion protein consisting of mRFP1-eGFP (red and green fluorescence in the same molecule)that acts as smart biological pH sensor to trace nanoparticles inside cells. Its fluorescence is also coupled to the structural integrity of the protein, i.e. it is also a label for a successful delivery of a functional protein into the cell. At pH 7.4, the fluorescence of both proteins (red and green) is detectable. At a pH of 4.5-5 inside the lysosomes, the green fluorescence is quenched due to the protonation of the eGFP chromophore, but the pH-independent red fluorescence of mRFP1 remains. The nanoparticles were taken up by cells (cell lines: HeLa, Caco-2 and A549) via endocytic pathways and then directed to lysosomes. Time-resolved confocal laser scanning microscopy confirmed mRFP1 and nanoparticles co-localizing with lysosomes. The fluorescence of eGFP was only detectable outside lysosomes, i.e. most likely inside early endosomes or at the cell membrane during the uptake, indicating the neutral pH at these locations. The Tandem fusion protein provides a versatile platform to follow the intracellular pathway of bioactive nanocarriers, e.g. therapeutic proteins. The transfection with a Tandem-encoding plasmid by calcium phosphate nanoparticles led to an even intracellular protein distribution in cytosol and nucleoplasm, i.e. very different from direct protein uptake. Neither dissolved protein nor dissolved plasmid DNA were taken up by the cells, underscoring the necessity for a suitable carrier like a nanoparticle. STATEMENT OF SIGNIFICANCE: A pH-sensitive protein ("tandem") was used to follow the pathway of calcium phosphate nanoparticles. This protein consists of a pH-sensitive fluorophore (eGFP; green) and a pH-independent fluorophore (mRFP1; red). This permits to follow the pathway of a nanoparticle inside a cell. At a low pH inside an endolysosome, the green fluorescence vanishes but the red fluorescence persists. This is also a very useful model for the delivery of therapeutic proteins into cells. The delivery by nanoparticles was compared with the protein expression after cell transfection with plasmid DNA encoding for the tandem protein. High-resolution image analysis gave quantitative data on the intracellular protein distribution.

Effect of nano-hydroxyapatite and ozone on approximal initial caries: a randomized clinical trial

The aim of the study was to assess the efficacy of three methods of enamel remineralization on initial approximal caries: (1) a nano-hydroxyapatite gel, (2) gaseous ozone therapy, (3) combination of a nano-hydroxyapatite gel and ozone. Patients (n = 92, age 20-30 years) with initial approximal enamel lesions on premolar and molar teeth (n = 546) were randomly allocated to three groups subjected to a 6-months treatment: Group I: domestic nano-hydroxyapatite remineralizing gel, group II: in-office ozone therapy, group III: both domestic remineralizing gel and ozone therapy. Caries lesions were assessed on bitewing radiographs at baseline, after 1 year and after 2 years. At one-year follow-up, the smallest rate of lesions with remineralisation (36.5%) was found in group I, and the highest (69.3%)-in group III. In group III a significant remineralisation was noticed in after 1 year and then a demineralisation after 2 years. Thus nano-hydroxyapatite gel and ozone therapy exert some capacities to remineralize approximal enamel and dentine subsurface lesions of premolar and molar teeth. Moreover, the combination of both methods produces the best effect compared to nano-hydroxyapatite or ozone therapy applied alone. However, the treatment should be continued for a long time in order to achieve nonrestorative recovery of caries.

Evaluation of the In Vivo Biocompatibility of Amorphous Calcium Phosphate-Containing Metals

Among the biomaterials based on calcium phosphate, hydroxyapatite has been widely used due to its biocompatibility and osteoconduction. The substitution of the phosphate group by the carbonate group associated with the absence of heat treatment and low synthesis temperature leads to the formation of carbonated hydroxyapatite (CHA). The association of CHA with other metals (strontium, zinc, magnesium, iron, and manganese) produces amorphous calcium phosphate-containing metals (ACPMetals), which can optimize their properties and mimic biological apatite. This study aimed to evaluate the biocompatibility and biodegradation of ACPMetals in mice subcutaneous tissue. The materials were physicochemically characterized with Fourier Transform InfraRed (FTIR), X-Ray Diffraction (XRD), and Atomic Absorption Spectrometry (AAS). Balb-C mice (n = 45) were randomly divided into three groups: carbonated hydroxyapatite, CHA (n = 15), ACPMetals (n = 15), and without implantation of material (SHAM, n = 15). The groups were subdivided into three experimental periods (1, 3, and 9 weeks). The samples were processed histologically for descriptive and semiquantitative evaluation of the biological effect of biomaterials according to ISO 10993-6:2016. The ACPMetals group was partially biodegradable; however, it presented a severe irritating reaction after 1 and 3 weeks and moderately irritating after nine weeks. Future studies with other concentrations and other metals should be carried out to mimic biological apatite.

Tailorable hierarchical structures of biomimetic hydroxyapatite micro/nano particles promoting endocytosis and osteogenic differentiation of stem cells

Hydroxyapatite (HA) micro/nano particles show great promise as artificial bone and dental substitutes, or drug carrier systems. However, the precise regulation of hydroxyapatite micro/nano particles with controllable physicochemical properties (such as hierarchical structure, particle size, potential and crystallinity) is still a challenge. Furthermore, the effects of different hierarchical structures on biological responses have been rarely reported. Herein, the HA particles with a precisely tailored micro/nano hierarchical structure have been developed using an elaborate biomimetic synthesis technology. Three representative particles, namely, micro/nano needle-like HA particles, micro/nano rod-like HA particles, and micro/nano flake-like HA particles, were featured to evaluate their biological responses to stem cells. The pore structure facilitated the adsorption of serum adhesive proteins, which together with the unique hierarchical architecture of micro/nano flake-like HA particles remarkably promoted the endocytosis efficiency in a concentration-dependent manner. The qRT-PCR together with RNA-seq and western blot analyses showed that micro/nano flake-like HA particles more significantly up-regulated the expression of genes and production of proteins related to osteogenic differentiation among the three particles through the activated ERK/MAPK signalling pathway. RNA-seq further revealed a complex mechanism of cell interface events, suggesting that the hierarchical architecture of HA particles is of crucial importance for the regulation of actin cytoskeleton involved in the modulation of cell adhesion which positively stimulated osteogenic differentiation of stem cells. Moreover, the endocytosis of particles into lysosomes resulted in an increase in the intracellular Ca²⁺ levels, which activated possible intracellular Ca²⁺-mediated signaling cascades (Ras/cAMP/Rap1/MAPK signaling pathways) related to osteogenic differentiation of stem cells. Our findings shed light on the effects of different hierarchical structures of HA particles on stem cell differentiation and contribute to the optimal design of implant materials.

Hidrogeles de colágeno acoplados con hidroxiapatita para aplicaciones en ingeniería tisular

Los hidrogeles basados en colágeno son redes tridimensionales (3D) con la capacidad de absorber agua y una alta biocompatibilidad para utilizarlos en la reparación de tejidos dañados. Estos materiales presentan pobres propiedades mecánicas y velocidades de degradación rápidas, limitando su aplicación a estrategias de ingeniería tisular y biomedicina; por ésto, la incorporación de fases inorgánicas en la matriz 3D del colágeno como la hidroxiapatita ha contribuido en la mejora de sus propiedades, incrementado la eficiencia de los hidrogeles híbridos obtenidos. Este trabajo, presenta las contribuciones más relevantes relacionadas con los sistemas de hidrogeles basados en colágeno y partículas de hidroxiapatita dispersas dentro de la matriz colagénica, lo que evidencia que la combinación de los materiales no altera la biocompatibilidad y biodegradabilidad típicas del colágeno, permitiendo la adhesión, proliferación, crecimiento celular y control del metabolismo de las células implicadas en los procesos de una reparación ósea, presentando a los hidrogeles como una estrategia para su uso potencial en la ingeniería tisular.