Chemicals from lignin: an interplay of lignocellulose fractionation, depolymerisation, and upgrading

Towards efficient enzymatic saccharification of pretreated lignocellulose: Enzyme inhibition by lignin-derived phenolics and recent trends in mitigation strategies

Lignocellulosic biorefinery based on its sugar-platform has been considered as an efficient strategy to replace fossil fuel-based refinery. In the bioconversion process, pretreatment is an essential step to firstly open up lignocellulose cell wall structure and enhance the accessibility of carbohydrates to hydrolytic enzymes. However, various lignin and/or carbohydrates degradation products (e.g. phenolics, 5-hydroxymethylfurfural, furfural) also generated during pretreatment, which severely inhibit the following enzymatic hydrolysis and the downstream fermentation process. Among them, the lignin derived phenolics have been considered as the most inhibitory compounds and their inhibitory effects are highly dependent on the source of biomass and the type of pretreatment strategy. Although liquid-solid separation and subsequent washing can remove the lignin derived phenolics and other inhibitors, this is undesirable in the realistic industrial application where the whole slurry of pretreated biomass need to be directly used in the hydrolysis process. This review summarizes the phenolics formation mechanism for various commonly applied pretreatment methods and discusses the key factors that affect the inhibitory effect of phenolics on cellulose hydrolysis. In addition, the recent achievements on the rational design of inhibition mitigation strategies to boost cellulose hydrolysis for sugar-platform biorefinery are also introduced. This review also provides guidance for rational design detoxification strategies to facilitate whole slurry hydrolysis which helps to realize the industrialization of lignocellulose biorefinery.

Operando PEPICO unveils the catalytic fast pyrolysis mechanism of the three methoxyphenol isomers

The development of lignin valorization processes such as catalytic fast pyrolysis (CFP) to produce fine chemicals and fuels leads to a more sustainable future. The implementation of CFP is enabled by understanding the chemistry of lignin constituents, which, however, requires thorough mechanistic investigations by detecting reactive species. In this contribution, we investigate the CFP of the three methoxyphenol (MP) isomers over H-ZSM-5 utilizing vacuum ultraviolet synchrotron radiation and operando photoelectron photoion coincidence (PEPICO) spectroscopy. All isomers demethylate at first to yield benzenediols, from which dehydroxylation reactions proceed to produce phenol and benzene. Additional pathways to form benzene proceed over cyclopentadiene, methylcyclopentadiene, and fulvene intermediates. The detection of trace amounts of methanol in the product stream suggests a demethoxylation reaction to yield phenol. Guaiacol (2- or ortho-MP) exhibits slightly higher reactivity compared to 3-MP and 4-MP, due to the formation of the fulvenone ketene, which opens additional routes to benzene and phenol. When compared to benzenediol catalytic pyrolysis, the additional methyl group in MP leads to high conversion at lower reactor temperatures, which is mostly owed to the lower H₃C–O vs. H–O bond energy and the possibility to demethoxylate to produce phenol.

Demethylation, demethoxylation and fulvenone ketene formation determine the reactivity of methoxyphenols over H-ZSM-5 to yield phenols, benzene and toluene. Intermediates are isomer-selectively detected utilizing threshold photoelectron spectroscopy.

Structural materials with afterglow room temperature phosphorescence activated by lignin oxidation

Sustainable afterglow room temperature phosphorescence (RTP) materials, especially afterglow RTP structural materials, are crucial but remain difficult to achieve. Here, an oxidation strategy is developed to convert lignin to afterglow materials with a lifetime of ~ 408 ms. Specifically, lignin is oxidized to give aromatic chromophores and fatty acids using H₂O₂. The aromatic chromophores are locked by a fatty acid-based matrix by hydrogen bonds, triggering enhanced spin orbit coupling and long afterglow emission. More interestingly, motivated by this discovery, an auto fabrication line is built to convert wood (natural structural materials) to wood with afterglow RTP emission (RTP wood) via in situ oxidation of naturally-occurring lignin located in the wood cell walls to oxidized lignin (OL). The as-prepared RTP wood exhibits great potential for the construction of sustainable afterglow furniture. With this research we provide a new strategy to promote the sustainability of afterglow RTP materials and structural materials.

Sustainable afterglow room temperature phosphorescence (RTP) Structural materials are difficult to achieve. Here, the authors demonstrate a wood based RTP material by oxidation of lignin to realize an afterglow RTP material with a lifetime of ~ 408 ms.

Oxidative C−C bond cleavage of lignin via electrocatalysis

Lignin, which is an important component of biomass in nature and is constantly produced in industry, becomes potential raw material for sustainable production of fine chemicals and biofuels. Electrocatalysis has been extensively involved in the activation of simple molecules and cleavage-recasting of complex scaffolds in an elegant environment. As such, electrocatalytic cleavage of C−C(O) in β-O-4 model molecules of lignin to value-added chemicals has received much attention in recent years. This mini-review introduces various anodes (e.g., Pb, Pt, Ni, Co., and Ir) developed for electro-oxidative lignin degradation (EOLD) under mild conditions. Attention was placed to understand the conversion pathways and involved reaction mechanisms during EOLD, with emphasis on the product distribution caused by different electrodes.

Green and stable lignin-based nanofillers reinforced poly(l-lactide) with supertough and strong performance

Lignin nanoparticles (LNPs), as a new type of green nanomaterial, initiate many promising applications in polymer composites. However, their heterogeneity, dissolution in organic solvents, and poor compatibility in the polymer matrix greatly limited the applications of LNPs fillers. Herein, we proposed an antisolvent precipitation of the fractionations by combining a hydrothermal treatment-assisted synthesis to fabricate self-crosslinked LNPs (ScLNPs), which have good stability in the organic solvent and controllable sizes. After surface grafting modification with d-lactide, ScLNPs-graft-poly(d-lactide) (ScLNPs-g-PDLA) exhibited excellent dispersion and compatibility in PLLA matrix. Using the rational design and addition of ScLNPs-g-PDLA fillers, the strength and toughness of the generated PLLA composite reached 31.6 MPa and 396 % (the highest value among the PLLA materials), respectively. Furthermore, the mechanical performance can also be well-tuned by the sizes and amounts of LNPs fillers. This strategy involving only green and recyclable materials provides an effective route to producing sustainable polymeric plastics with integrated strength and super-toughness.

Revisiting alkaline cupric oxide oxidation method for lignin structural analysis

Lignin structural analysis is important for the comprehensive utilization of lignin as well as delignification and bleaching during pulping while it is difficult to completely elucidate lignin structure due to its structural complexity and heterogeneity. Depolymerization of lignin into simple monomers via alkaline cupric oxide oxidation (OxCuO) followed by chromatographic analysis of the monomers is an effective method for lignin structural analysis. Here we revisited the OxCuO of lignin model compounds (monomers and dimers) and three representative lignocelluloses (i.e., Eucalyptus, Masson pine, and corn stover) to understand the effects of reaction conditions and lignin sub-structures on oxidation product yields and distributions. The improved OxCuO was found to be effective in oxidatively breaking the robust interunit C-C bonds in the β-β′ and β-5′ moieties of lignin other than β-O-4′ linkages at an elevated temperature (210°C). Further degradation of the monomeric oxidation products could also occur to reduce the monomer yields under a severe condition (i.e., high temperature and long reaction time). In addition, O2 inputs could reduce the monomer yields via nonselective overoxidation, thus having negative effects on accurate structural analysis of lignin. The O2 removal via ultrasonication combined with N2 flushing prior to the oxidation reaction could improve the monomer yield about 1.2 times (compared to that without O2 removal) at a low biomass loading of 5 wt%. By using the improved method of OxCuO, a monomer yield of 71.9% could be achieved from Eucalyptus (hardwood) lignin, which was much higher than conventional nitrobenzene oxidation (59.8%) and reductive depolymerization (51.9%). Considering the low cost, high availability, and low toxicity of CuO, the improved OxCuO could be a convenient and economic method for more accurate lignin structural analysis.

Catalytic Oxidation of Flax Shives into Vanillin and Pulp

This research deals with a process of catalytic oxidation of flax shives to vanillin and pulp. Catalytic oxidation of flax shives with molecular oxygen allows two main products to be obtained—vanillin with a yield of up to 12 wt.% of lignin, and pulp. Final forms of the catalyst particles (Cu2O and CuO) are agglomerates or monocrystals 0.5–5 µm in size. Acid prehydrolysis of the shives does not affect the oxidation, in contrast to pine-wood oxidation. Lignin prehydrolysis and oxidation was suggested as illustrate this difference. The dependence of the vanillin formation rate on stirring speed was studied. Minimum alkali consumption in the process was attained with a mild stirring speed of the reaction mass.

Valorization of lignocellulosic biomass for polyhydroxyalkanoate production: Status and perspectives

With the increasing concerns regarding climate, energy, and plastic crises, bio-based production of biodegradable polymers has become a dire necessity. Significant progress has been made in biotechnology for the production of biodegradable polymers from renewable resources to achieve the goal of zero plastic waste and a net-zero carbon bioeconomy. In this review, an overview of polyhydroxyalkanoate (PHA) production from lignocellulosic biomass (LCB) was presented. Having established LCB-based biorefinery with proper pretreatment techniques, various PHAs could be produced from LCB-derived sugars, hydrolysates, and/or aromatic mixtures employing microorganisms. This provides a clue for addressing the current environmental crises because "biodegradable polymers" could be produced from one of the most abundant resources that are renewable and sustainable in a "carbon-neutral process". Furthermore, the potential future of LCB-to-non-natural PHA production was discussed with particular reference to non-natural PHA biosynthesis methods and LCB-derived aromatic mixture biofunnelling systems.

Systematic review on lignin valorization in the agro-food system: From sources to applications

Lignocellulosic biomass is the most abundant renewable resource on earth and currently most of this biomass is considered a low-value waste. Specifically, lignin is an underrated bioresource that is mostly burned for energy production and few value-added products have been created. Since the agro-food industry produces large amounts of wastes that can be potential sources of high-quality lignin, scientific efforts should be directed to this industry. Thus, this review provides a systematic overview of the trends and evolution of research on agro-food system-derived lignin (from 2010 to 2020), including the extraction of lignin from various agro-food sources and emergent applications of lignin in the agro-food chain. Crops with the highest average production/year (n = 26) were selected as potential lignin sources. The extraction process efficiency (yield) and lignin purity were used as indicators of the raw material potential. Overall, it is notable that research interest on agro-food lignin has increased exponentially over the years, both as source (567%) and application (128%). Wheat, sugarcane, and maize are the most studied sources and are the ones that render the highest lignin yields. As for the extraction methods used, alkaline and organosolv methods are the most employed (∼50%). The main reported applications are related to lignin incorporation in polymers (∼55%) and as antioxidant (∼24%). Studies on agro-food system-derived lignin is of most importance since there are numerous possible sources that are yet to be fully valorized and many promising applications that need to be further developed.

The Catabolic System of Acetovanillone and Acetosyringone in Sphingobium sp. Strain SYK-6 Useful for Upgrading Aromatic Compounds Obtained through Chemical Lignin Depolymerization

Acetovanillone is a major aromatic monomer produced in oxidative/base-catalyzed lignin depolymerization. However, the production of chemical products from acetovanillone has not been explored due to the lack of information on the microbial acetovanillone catabolic system. Here, the acvABCDEF genes were identified as specifically induced genes during the growth of Sphingobium sp. strain SYK-6 cells with acetovanillone and these genes were essential for SYK-6 growth on acetovanillone and acetosyringone (a syringyl-type acetophenone derivative). AcvAB and AcvF produced in Escherichia coli phosphorylated acetovanillone/acetosyringone and dephosphorylated the phosphorylated acetovanillone/acetosyringone, respectively. AcvCDE produced in Sphingobium japonicum UT26S carboxylated the reaction products generated from acetovanillone/acetosyringone by AcvAB and AcvF into vanilloyl acetic acid/3-(4-hydroxy-3,5-dimethoxyphenyl)-3-oxopropanoic acid. To demonstrate the feasibility of producing cis,cis-muconic acid from acetovanillone, a metabolic modification on a mutant of Pseudomonas sp. strain NGC7 that accumulates cis,cis-muconic acid from catechol was performed. The resulting strain expressing vceA and vceB required for converting vanilloyl acetic acid to vanillic acid and aroY encoding protocatechuic acid decarboxylase in addition to acvABCDEF successfully converted 1.2 mM acetovanillone to approximately equimolar cis,cis-muconic acid. Our results are expected to help improve the yield and purity of value-added chemical production from lignin through biological funneling. IMPORTANCE In the alkaline oxidation of lignin, aromatic aldehydes (vanillin, syringaldehyde, and p-hydroxybenzaldehyde), aromatic acids (vanillic acid, syringic acid, and p-hydroxybenzoic acid), and acetophenone-related compounds (acetovanillone, acetosyringone, and 4'-hydroxyacetophenone) are produced as major aromatic monomers. Also, base-catalyzed depolymerization of guaiacyl lignin resulted in vanillin, vanillic acid, guaiacol, and acetovanillone as primary aromatic monomers. To date, microbial catabolic systems of vanillin, vanillic acid, and guaiacol have been well characterized, and the production of value-added chemicals from them has also been explored. However, due to the lack of information on the microbial acetovanillone and acetosyringone catabolic system, chemical production from acetovanillone and acetosyringone has not been achieved. This study elucidated the acetovanillone/acetosyringone catabolic system and demonstrates the potential of using these genes for the production of value-added chemicals from these compounds.

Biocatalytic Production of a Nylon 6 Precursor from Caprolactone in Continuous Flow

6-Aminocaproic acid (6ACA) is a key building block and an attractive precursor of caprolactam, which is used to synthesize nylon 6, one of the most common polymers manufactured nowadays. (Bio)-production of platform chemicals from renewable feedstocks is instrumental to tackle climate change and decrease fossil fuel dependence. Here, the cell-free biosynthesis of 6ACA from 6-hydroxycaproic acid was achieved using a co-immobilized multienzyme system based on horse liver alcohol dehydrogenase, Halomonas elongata transaminase, and Lactobacillus pentosus NADH oxidase for in-situ cofactor recycling, with >90 % molar conversion (m.c.) The integration of a step to synthesize hydroxy-acid from lactone by immobilized Candida antarctica lipase B resulted in >80 % m.c. of ϵ-caprolactone to 6ACA, >20 % of δ-valerolactone to 5-aminovaleric acid, and 30 % of γ-butyrolactone to γ-aminobutyric acid in one-pot batch reactions. Two serial packed-bed reactors were set up using these biocatalysts and applied to the continuous-flow synthesis of 6ACA from ϵ-caprolactone, achieving a space-time yield of up to 3.31 g_6ACA  h^-1  L^-1 with a segmented liquid/air flow for constant oxygen supply.

Thermochemical depolymerization of lignin: Process analysis with state-of-the-art soft ionization mass spectrometry

Lignin valorization via thermochemical approaches has the potential to produce renewable fuels and value-added chemicals, which are of great significance to the sustainable development of human beings. During the thermochemical depolymerization which involves acid-catalyzed, alkali-catalyzed, oxidative, reductive, pyrolytic, and other reactions, the lignin structure will undergo a series of bond cleavage, condensation, and functional group changes, while the mechanism is still unclear. To improve the efficiency, the analysis of the evolution of intermediates during depolymerization is very important, among which soft ionization mass spectrometry plays a vital role. This review aims to summarize the research progress of process analysis of lignin depolymerization in both gas-phase, typically thermal and catalytic pyrolysis, and liquid-phase via online mass spectrometry. The challenges and our insights into the future development of the lignin valorization as well as soft ionization mass spectrometry methods are also discussed.

A unified view on catalytic conversion of biomass and waste plastics

Originating from the desire to improve sustainability, producing fuels and chemicals from the conversion of biomass and waste plastic has become an important research topic in the twenty-first century. Although biomass is natural and plastic synthetic, the chemical nature of the two are not as distinct as they first appear. They share substantial structural similarities in terms of their polymeric nature and the types of bonds linking their monomeric units, resulting in close relationships between the two materials and their conversions. Previously, their transformations were mostly studied and reviewed separately in the literature. Here, we summarize the catalytic conversion of biomass and waste plastics, with a focus on bond activation chemistry and catalyst design. By tracking the historical and more recent developments, it becomes clear that biomass and plastic have not only evolved their unique conversion pathways but have also started to cross paths with each other, with each influencing the landscape of the other. As a result, this Review on the catalytic conversion of biomass and waste plastic in a unified angle offers improved insights into existing technologies, and more importantly, may enable new opportunities for future advances.

Biomass and plastic share structural similarities in their composition and types of bond linkage between their monomeric units. Reviewing their catalytic conversion technologies in a unified angle provides new insights and opportunities for future advances.

First-Generation Organic Reaction Intermediates in Zeolite Chemistry and Catalysis

Zeolite chemistry and catalysis are expected to play a decisive role in the next decade(s) to build a more decentralized renewable feedstock-dependent sustainable society owing to the increased scrutiny over carbon emissions. Therefore, the lack of fundamental and mechanistic understanding of these processes is a critical "technical bottleneck" that must be eliminated to maximize economic value and minimize waste. We have identified, considering this objective, that the chemistry related to the first-generation reaction intermediates (i.e., carbocations, radicals, carbenes, ketenes, and carbanions) in zeolite chemistry and catalysis is highly underdeveloped or undervalued compared to other catalysis streams (e.g., homogeneous catalysis). This limitation can often be attributed to the technological restrictions to detect such "short-lived and highly reactive" intermediates at the interface (gas-solid/solid-liquid); however, the recent rise of sophisticated spectroscopic/analytical techniques (including under in situ/operando conditions) and modern data analysis methods collectively compete to unravel the impact of these organic intermediates. This comprehensive review summarizes the state-of-the-art first-generation organic reaction intermediates in zeolite chemistry and catalysis and evaluates their existing challenges and future prospects, to contribute significantly to the "circular carbon economy" initiatives.

Effect of alkaline and deep eutectic solvents pretreatments on the recovery of lignin with antioxidant activity from grape stalks

Grape stalks are lignocellulosic residues that can be valorized through the extraction of lignin - an underutilized biopolymer with high potential. Two lignin extraction methods, alkaline and deep eutectic solvents (DES), were studied, and experimental designs were carried out to obtain the best extraction conditions. The defined parameters for alkaline extraction allowed the recovery of ~48 % of lignin with low purity that was further improved with an autohydrolysis pretreatment (~79 % purity; ~32 % yield). Optimum parameters of DES method rendered high purity lignin (~90 %) without the need of a pretreatment and with a better yield (50.2 % (±2.3)) than the alkaline method. Both lignin fractions presented high antioxidant activities, being close to the antioxidant capacity of BHT for DPPH scavenging. Structural analysis proved the presence of lignin in both alkaline and DES samples with similar morphology. Overall, DES method was more efficient in the extraction of lignin from grape stalks besides its greener and sustainable nature. This work is uses DES to extract lignin from this biomass while comparing it with a commonly classical method, proving that grape stalks can be used to extract lignin with a sustainable and efficient method rendering a final ingredient with value-added properties.

Discovery of lignin-transforming bacteria and enzymes in thermophilic environments using stable isotope probing

Characterizing microorganisms and enzymes involved in lignin biodegradation in thermal ecosystems can identify thermostable biocatalysts. We integrated stable isotope probing (SIP), genome-resolved metagenomics, and enzyme characterization to investigate the degradation of high-molecular weight, ¹³C-ring-labeled synthetic lignin by microbial communities from moderately thermophilic hot spring sediment (52 °C) and a woody "hog fuel" pile (53 and 62 °C zones). ¹³C-Lignin degradation was monitored using IR-GCMS of ¹³CO₂, and isotopic enrichment of DNA was measured with UHLPC-MS/MS. Assembly of 42 metagenomic libraries (72 Gb) yielded 344 contig bins, from which 125 draft genomes were produced. Fourteen genomes were significantly enriched with ¹³C from lignin, including genomes of Actinomycetes (Thermoleophilaceae, Solirubrobacteraceae, Rubrobacter sp.), Firmicutes (Kyrpidia sp., Alicyclobacillus sp.) and Gammaproteobacteria (Steroidobacteraceae). We employed multiple approaches to screen genomes for genes encoding putative ligninases and pathways for aromatic compound degradation. Our analysis identified several novel laccase-like multi-copper oxidase (LMCO) genes in ¹³C-enriched genomes. One of these LMCOs was heterologously expressed and shown to oxidize lignin model compounds and minimally transformed lignin. This study elucidated bacterial lignin depolymerization and mineralization in thermal ecosystems, establishing new possibilities for the efficient valorization of lignin at elevated temperature.

The Practical Utility of Imidazolium Hydrogen Sulfate Ionic Liquid in Fabrication of Lignin-Based Spheres: Structure Characteristic and Antibacterial Activity

In this study, lignin-based spherical particles (Lig-IL) with the use of 1-(propoxymethyl)-1H-imidazolium hydrogen sulfate were prepared in different biopolymer and ionic liquid (IL) weight ratios. The application of IL during the preparation of spherical particles is an innovative method, which may be beneficial for further applications. The particles were obtained with the use of the soft-templating method and their chemical, structural and morphological characterization was performed. The spherical shape of products and their size (91–615 nm) was confirmed with the use of scanning electron microscopy (SEM) images and the particle size distribution results. The attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectra were analyzed to identify functional groups of all precursors and produced material and it was confirmed, that all materials exhibit characteristic hydroxyl and carboxylic groups, but the presence of carbonyl group was detected. Moreover, the zeta potential analysis was performed to evaluate the electrokinetic behavior of obtained materials. It was confirmed, that all materials are colloidally stable in pH above 4. Produced lignin-based spherical particles were used for evaluation of their antibacterial properties. Particles were tested against Staphylococcus aureus (S. aureus), a gram-positive bacterium, and Escherichia coli (E. coli), a gram-negative one. It was observed, that only the material with the highest addition of IL showed the antibacterial properties against both strains. A reduction of 50% in the number of microorganisms was observed for particles with the addition of hydrogen sulfate ionic liquid in a 1:1 ratio after 1 h. However, all prepared materials exhibited the antibacterial activity against a gram-positive bacterium.

Sustainable Production of Bioactive Molecules from C-Lignin-Derived Propenylcatechol

Catechyl lignin (C-lignin) is a naturally occurring linear homogeneous biopolymer composed solely of caffeyl alcohol subunits with cleavable benzodioxane linkages. The inherent structural features of propenylcatechol, a direct depolymerized product of castor seed coats C-lignin, render it a sustainable and promising platform for the synthesis of bioactive molecules. Herein, diversified transformations of propenylcatechol, including C=C bond difunctionalization, β-modification, β,γ-rearrangement, and γ-methyl derivatization, were reported based on known or developed methods. A series of functional molecular skeletons involved in the current synthetic routes for the preparation of pharmaceuticals and bioactive molecules were obtained. Starting from castor seed coats, annuloline (natural product) and CC-5079 (antitumor) were synthesized using facile and inexpensive reagents in only four- and five-sequence reactions, respectively, thereby demonstrating a superior step-efficiency to that of reported synthetic routes. Almost all atoms in the C-lignin biopolymer were incorporated into the final products owing to the intrinsic structures of naturally occurring C-lignin. Bioactive molecules produced from C-lignin integrate a low-carbon footprint with high-quality and economical manufacture of pharmaceuticals.

Technology Overview of Fast Pyrolysis of Lignin: Current State and Potential for Scale-Up

Lignin is an abundant natural polymer obtained from lignocellulosic biomass and rich in aromatic substructures. When efficiently depolymerized, it has great potential in the production of value-added chemicals. Fast pyrolysis is a promising depolymerization method, but current studies focus mainly on small quantities of lignin. In this Review, to determine the potential for upscaling, systems used in the most relevant unit operations of fast pyrolysis of lignin are evaluated. Fluidized-bed reactors have the most potential. It would be beneficial to combine them with the following: slug injectors for feeding, hot particle filters, cyclones, and fractional condensation for product separation and recovery. Moreover, upgrading lignin pyrolysis oil would allow the necessary quality parameters for particular applications to be reached.

5-Hydroxymethylfurfural and Furfural Chemistry Toward Biobased Surfactants

The use of 5-hydroxymethylfurfural (HMF), furfural, and furan as scaffolds for designing alternative surfactants is a rapidly developing research area. This Review gathers recent examples highlighting the variety of methods for grafting the necessary polar and non-polar appendages, exploiting the specific chemical reactivity of each of these platform molecules. While the furan (or tetrahydrofuran) backbone is maintained in some targeted amphiphiles, alternatives using rearranged HMF or furfural such as cyclopentanols or furanones have also been reported. This topic is an illustration of the diversification of the use of HMF and other biobased furanic platform molecules in the field of fine and specialty chemicals. The surfactants sector, which concerns some of the most largely consumed chemicals in everyday life, and still mostly produced from fossil resources, will benefit from such alternatives enabling increased renewable carbon content and structural innovation.

Spatio-Temporal Modification of Lignin Biosynthesis in Plants: A Promising Strategy for Lignocellulose Improvement and Lignin Valorization

Lignin is essential for plant growth, structural integrity, biotic/abiotic stress resistance, and water transport. Besides, lignin constitutes 10–30% of lignocellulosic biomass and is difficult to utilize for biofuel production. Over the past few decades, extensive research has uncovered numerous metabolic pathways and genes involved in lignin biosynthesis, several of which have been highlighted as the primary targets for genetic manipulation. However, direct manipulation of lignin biosynthesis is often associated with unexpected abnormalities in plant growth and development for unknown causes, thus limiting the usefulness of genetic engineering for biomass production and utilization. Recent advances in understanding the complex regulatory mechanisms of lignin biosynthesis have revealed new avenues for spatial and temporal modification of lignin in lignocellulosic plants that avoid growth abnormalities. This review explores recent work on utilizing specific transcriptional regulators to modify lignin biosynthesis at both tissue and cellular levels, focusing on using specific promoters paired with functional or regulatory genes to precisely control lignin synthesis and achieve biomass production with desired properties. Further advances in designing more appropriate promoters and other regulators will increase our capacity to modulate lignin content and structure in plants, thus setting the stage for high-value utilization of lignin in the future.

Highly selective separation of eucalyptus hemicellulose by salicylic acid treatment with both aromatic and hydroxy acids

Aromatic and hydroxyl acid treatments demonstrate their respective characteristics for the separation of lignocellulosic biomass. In this study, the effect of salicylic acid (SA-A) treatment on the separation of eucalyptus components with both aromatic and hydroxyl acid properties was analyzed. The optimal conditions were SA-A concentration 9.0%, reaction temperature 140 °C and time 75 min. The separation yield of xylose was 85.93%. The separation of cellulose and lignin was inhibited by SA-A treatment in contrast to the separation by glycolic acid and p-toluenesulfonic acid treatment. Moreover, SA-A treatment resulted in a larger fiber crystallinity index and higher thermal stability. The SA-A-treated samples contained lignin that was rich in β-O-4 and hydroxyl groups. The degradation and condensation of lignin was inhibited. The selectivity of aromatic acids for separating hemicellulose and protecting the lignin structure using hydroxy acids was demonstrated. Thus, new and efficient organic acid treatments can be developed.

The Consistency of Yields and Chemical Composition of HTL Bio-Oils from Lignins Produced by Different Preprocessing Technologies

This work evaluates the effect of feedstock type and composition on the conversion of lignin to liquid by solvolysis with formic acid as hydrogen donor (LtL), by analyzing the yields and molecular composition of the liquid products and interpreting them in terms of both the type and the preprocessing of the lignocellulosic biomass using chemometric data analysis. Lignin samples of different types and purities from softwood, hardwood, and grasses (rice straw and corn stover) have been converted to bio-oil, and the molecular composition analyzed and quantified using GC-MS. LtL solvolysis was found to be a robust method for lignin conversion in terms of converting all samples into bio-oils rich in phenolic compounds regardless of the purity of the lignin sample. The bio-oil yields ranged from 24–94 wt.% relative to lignin input and could be modelled well as a function of the elemental composition of the feedstock. On a molecular basis, the softwood-derived bio-oil contained the most guaiacol-derivatives, and syringol was correlated to hardwood. However, the connection between compounds in the bio-oil and lignin origin was less pronounced than the effects of the methods for biomass fractionation, showing that the pretreatment of the biomass dominates both the yield and molecular composition of the bio-oil and must be addressed as a primary concern when utilization of lignin in a biorefinery is planned.

Lignin-First Depolymerization of Lignocellulose into Monophenols over Carbon Nanotube-Supported Ruthenium: Impact of Lignin Sources

Lignin-first depolymerization of lignocellulosic biomass into aromatics is of great significance to sustainable biorefinery. However, it remains a challenge, owing to the variance between lignin sources and structures. In this study, ruthenium supported on carbon nanotubes (Ru/CNT) exhibits efficient catalytic activity toward lignin hydrogenolysis to exclusively afford monophenols in high yields. Catalytic tests indicate that the yields of aromatic monomers are related to lignin sources and decrease in the order: hardwoods > herbaceous plants > softwoods. Experimental results demonstrate that the scission of C-O bonds and the high selectivity to monomeric aromatic compounds over the Ru/CNT catalyst are enhanced by avoiding side condensation. Furthermore, the fabricated Ru/CNT shows good reusability and recyclability, applicability, and biomass feedstock compatibility, rendering it a promising candidate for lignin valorization. These findings pave the way for rational design of highly active and stable catalysts to potentially address challenges in lignin chemistry.

Fully lignocellulose-based PET analogues for the circular economy

Polyethylene terephthalate is one of the most abundantly used polymers, but also a significant pollutant in oceans. Due to growing environmental concerns, polyethylene terephthalate alternatives are highly sought after. Here we present readily recyclable polyethylene terephthalate analogues, made entirely from woody biomass. Central to the concept is a two-step noble metal free catalytic sequence (Cu20-PMO catalyzed reductive catalytic fractionation and Raney Ni mediated catalytic funneling) that allows for obtaining a single aliphatic diol 4-(3-hydroxypropyl) cyclohexan-1-ol in high isolated yield (11.7 wt% on lignin basis), as well as other product streams that are converted to fuels, achieving a total carbon yield of 29.5%. The diol 4-(3-hydroxypropyl) cyclohexan-1-ol is co-polymerized with methyl esters of terephthalic acid and furan dicarboxylic acid, both of which can be derived from the cellulose residues, to obtain polyesters with competitive Mw and thermal properties (T_g of 70–90 °C). The polymers show excellent chemical recyclability in methanol and are thus promising candidates for the circular economy.

‘Polyethylene terephthalate is a widely used polymer with a concerning environmental impact, and alternatives are now highly sought. In this article, the authors present a biorefinery strategy for constructing polyester analogues of polyethylene terephthalate from woody biomass, which are promising candidates for the circular economy.

Titanate Nanotubes-Based Heterogeneous Catalyst for Efficient Production of Biomass Derived Chemicals

The development of efficient heterogeneous catalytic system to convert plentiful biomass to renewable bio-chemicals is urgent need. Titanate nanotubes-based materials obtained from hydrothermal treatment have been reported as low-cost and efficient catalytic materials in chemical syntheses for bio-based chemicals production with interesting catalytic performance. This mini-review expressly revealed the significance and potential of using titanate nanotubes based material as sustainable and environmentally benign solid catalysts/supports for synthesis of various bio-based chemicals, including glycerol-derived solketal, jet fuel range alkanes precursors, biomass-derived esters, aldehydes, aromatic compounds and so on. From the current knowledge on titanate nanotubes-based material via hydrothermal method here summarized, the future lines of research in the field of catalysis/supports for bio-based chemicals production are outlined.

Structural elucidation and targeted valorization of poplar lignin from the synergistic hydrothermal-deep eutectic solvent pretreatment

Elucidating the structural variations of lignin during the pretreatment is very important for lignin valorization. Herein, poplar wood was pretreated with an integrated process, which was composed of AlCl₃-catalyzed hydrothermal pretreatment (HTP, 130-150 °C, 1.0 h) and mild deep-eutectic solvents (DES, 100 °C, 10 min) delignification for recycling lignin fractions. Confocal Raman Microscopy (CRM) was developed to visually monitor the delignification process during the HTP-DES pretreatment. NMR characterizations (2D-HSQC and ³¹P NMR) and elemental analysis demonstrated that the lignin fractions had undergone the following structural changes, such as dehydration, depolymerization, condensation. Molecular weights (GPC), microstructure (SEM and TEM), and antioxidant activity (DPPH analysis) of the lignins revealed that the DES delignification resulted in homogeneous lignin fragments (1.32 < PDI < 1.58) and facilitated the rapid assemblage of lignin nanoparticles (LNPs) with controllable nanoscale sizes (30-210 nm) and excellent antioxidant activity. These findings will enhance the understanding of structural transformations of the lignin during the integrated process and maximize the lignin valorization in a current biorefinery process.

Systems biology-guided understanding of white-rot fungi for biotechnological applications: a review

Plant-derived biomass is the most abundant biogenic carbon source on Earth. Despite this, only a small clade of organisms known as white-rot fungi (WRF) can efficiently break down both the polysaccharide and lignin components of plant cell walls. This unique ability imparts a key role for WRF in global carbon cycling and highlights their potential utilization in diverse biotechnological applications. To date, research on WRF has primarily focused on their extracellular ‘digestive enzymes’ whereas knowledge of their intracellular metabolism remains underexplored. Systems biology is a powerful approach to elucidate biological processes in numerous organisms, including WRF. Thus, here we review systems biology methods applied to WRF to date, highlight observations related to their intracellular metabolism, and conduct comparative extracellular proteomic analyses to establish further correlations between WRF species, enzymes, and cultivation conditions. Lastly, we discuss biotechnological opportunities of WRF as well as challenges and future research directions.

Standard-Free Quantification of Dicarboxylic Acids: Case Studies with Salt-Rich Effluents and Serum

The present study evaluates the ionization efficiency (IE) of linear and branched C₂-C₁₄ dicarboxylic acids (DCAs) by electrospray ionization (ESI) under different conditions. The influence of the concentration of organic modifier (MeOH); mobile phase additive; and its concentration, pH, and DCA structure on IE values is studied using flow injection analysis. The IE values of DCAs increase with the increase of MeOH concentration but also decrease with an increase of pH. The former is due to the increase in solvent evaporation rates; the latter is caused by an ion-pairing between the diacid and the cation (ammonium), which is confirmed by the study with different amines. The investigation of DCA ionization in the presence of different acidic mobile phase additives showed that a significant improvement in the (-)ESI responses of analytes was achieved in the presence of weak hydrophobic carboxylic acids, such as butyric or propanoic acid. Conversely, the use of strong carboxylic acids, such as trichloroacetic acid, was found to cause signal suppression. The results of the IE studies were used to develop the liquid chromatography-high-resolution mass spectrometry (LC-HRMS) method that provided instrumental limits of detection in the range from 6 to 180 pg. Furthermore, upon applying the nonparametric Gaussian process, a model for the prediction of IE values was developed, which contains the number of carbons in the molecule and MeOH concentration as model parameters. As a case study, dicarboxylic acids are quantified in salt-rich effluent and blood serum samples using the developed LC-HRMS method.