Biological response of chondrocytes cultured in three‐dimensional nanofibrous poly(ϵ‐caprolactone) scaffolds

Biodegradable PCL scaffolds with an interconnected spherical pore network for tissue engineering

A technique for producing controlled interconnected porous structures for application as a tissue engineering scaffold is presented in this article. The technique is based on the fabrication of a template of interconnected poly(ethyl methacrylate) (PEMA) microspheres, the introduction of a biodegradable polymer, poly-epsilon-caprolactone (PCL), and the elimination of the template by a selective solvent. A series of PCL scaffolds with a porosity of 70% and pore sizes up to 200 microm were produced and characterized (both thermally and mechanically). Human chondrocytes were cultured in monolayer on bulk PCL disks or seeded into porous PCL scaffolds. Cell adhesion, viability, proliferation, and proteoglycan (PG) synthesis were tested and compared with monolayer cultures on tissue-treated polystyrene or pellet cultures as reference controls. Cells cultured on PCL disks showed an adhesion similar to that of the polystyrene control (which allowed high levels of proliferation). Stained scaffold sections showed round-shaped chondrocyte aggregates embedded into porous PCL. PG production was similar to that of the pellet cultures and higher than that obtained with monolayer postconfluence cultures. This shows that the cells are capable of attaching themselves to PCL. Furthermore, in porous PCL, cells maintain the same phenotype as the chondrocytes within the native cartilage. These results suggest that PCL scaffolds may be a suitable candidate for chondrocyte culture.

Electrospun-modified nanofibrous scaffolds for the mineralization of osteoblast cells

Biocompatible polycaprolactone (PCL) and hydroxyapatite (HA) were fabricated into nanofibrous scaffolds for the mineralization of osteoblasts in bone tissue engineering. PCL and PCL/HA nanofibrous surface were modified using oxygen plasma treatment and showing 0 degrees contact angle for the adhesion and mineralization of osteoblast cells. The fiber diameter, pore size and porosity of nanofibrous scaffolds were estimated to be 220-625 nm, 3-20 microm, and 87-92% respectively. The ultimate tensile strength of PCL was about 3.37 MPa and PCL/HA was 1.07 MPa to withstand the long term culture of osteoblasts on nanofibrous scaffolds. Human fetal osteoblast cells (hFOB) were cultured on PCL and PCL/HA surface modified and unmodified nanofibrous scaffolds. The osteoblast proliferation rate was significantly (p < 0.001) increased in surface-modified nanofibrous scaffolds. FESEM showed normal phenotypic cell morphology and mineralization occurred in PCL/HA nanofibrous scaffolds, HA acting as a chelating agent for the mineralization of osteoblast to form bone like apatite for bone tissue engineering. EDX and Alizarin Red-S staining indicated mineral Ca(2+) and phosphorous deposited on the surface of osteoblast cells. The mineralization was significantly increased in PCL/HA-modified nanofibrous scaffolds and appeared as a mineral nodule synthesized by osteoblasts similar to apatite of the natural bone. The present study indicated that the PCL/HA surface-modified nanofibrous scaffolds are potential for the mineralization of osteoblast for bone tissue engineering.

A porous PCL scaffold promotes the human chondrocytes redifferentiation and hyaline-specific extracellular matrix protein synthesis

The redifferentiation, proliferation, and hyaline-specific extracellular matrix (ECM) protein synthesis of chondrocytes cultured in a polycaprolactone (PCL) scaffold were analyzed. Gene expression of the type II collagen and aggrecan was assessed by real-time PCR in cells from PCL scaffolds, monolayer, and pellet cultures. The proliferative activity was assessed using Ki-67 immunodetection, and the chondrocytic differentiation was evaluated using S-100 immunodetection. The synthesis and deposition into scaffold pores of type II collagen and glycosaminoglycan were analyzed by immunohistochemistry and Alcian blue staining, respectively. All parameters were assessed throughout 28 days of cultures maintained in either fetal bovine serum-containing medium (FCM) or Insulin-Transferrin-Selenium-containing medium (ICM). Expression of the type II collagen gene was lower in FCM cultures than in ICM cultures for all culture systems (p < 0.05). Moreover, PCL scaffolds cultured in ICM were able to induce collagen gene expression more efficiently than pellet and monolayer cultures. Aggrecan gene expression did not vary significantly between mediums and three-dimensional system cultures, but in ICM cultures, the monolayer cultures had significantly higher levels of aggrecan gene expression than did either the PCL or pellet cultures. Chondrocytes cultured in PCL scaffolds or pellets with FCM did not proliferate to a great extent but did maintain their differentiated phenotype for 28 days. Levels of cartilage ECM protein synthesis and deposition into the scaffold pores were similar among PCL and pellet cultures grown in FCM and in ICM. In conclusion, chondrocytes seeded into PCL scaffolds, cultured in ICM, efficiently maintained their differentiated phenotype and were able to synthesize cartilage-specific ECM proteins.

Scaffold stiffness influences cell behavior: opportunities for skeletal tissue engineering

Skeletal defects resulting from trauma, tumors, or abnormal development frequently require surgical treatment to restore normal tissue function. To overcome the limitations associated with conventional surgical treatments, several tissue engineering approaches have been developed. In particular, the use of scaffolds enriched with stem cells appears to be a very promising strategy. A crucial issue in this approach is how to control stem cell behavior. In this respect, the effects of growth factors, scaffold surface characteristics, and external ‘active’ loading conditions on stem cell behavior have been investigated. Recently, it has become clear that the stiffness of a scaffold is a highly potent regulator of stem cell differentiation. In addition, the stiffness of a scaffold affects cell migration, which is important for the infiltration of host tissue cells. This review summarizes current knowledge on the role of the scaffold stiffness in the regulation of cell behavior. Furthermore, we discuss how this knowledge can be incorporated in scaffold design which may provide new opportunities in the context of orthopedic tissue engineering.

Cell-nanofiber-based cartilage tissue engineering using improved cell seeding, growth factor, and bioreactor technologies

Biodegradable nanofibrous scaffolds serving as an extracellular matrix substitute have been shown to be applicable for cartilage tissue engineering. However, a key challenge in using nanofibrous scaffolds for tissue engineering is that the small pore size limits the infiltration of cells, which may result in uneven cell distribution throughout the scaffold. This study describes an effective method of chondrocyte loading into nanofibrous scaffolds, which combines cell seeding, mixing, and centrifugation to form homogeneous, packed cell-nanofiber composites (CNCs). When the effects of different growth factors are compared, CNCs cultured in medium containing a combination of insulin-like growth factor-1 and transforming growth factor-beta1 express the highest mRNA levels of collagen type II and aggrecan. Radiolabeling analyses confirm the effect on collagen and sulfated-glycosaminoglycans (sGAG) production. Histology reveals chondrocytes with typical morphology embedded in lacuna-like space throughout the entire structure of the CNC. Upon culturing using a rotary wall vessel bioreactor, CNCs develop into a smooth, glossy cartilage-like tissue, compared to a rough-surface tissue when maintained in a static environment. Bioreactor-grown cartilage constructs produce more total collagen and sGAG, resulting in greater gain in net tissue weight, as well as express cartilage-associated genes, including collagen types II and IX, cartilage oligomeric matrix protein, and aggrecan. In addition, dynamic culture enhances the mechanical property of the engineered cartilage. Taken together, these results indicate the applicability of nanofibrous scaffolds, combined with efficient cell loading and bioreactor technology, for cell-based cartilage tissue engineering.

Three-dimensional electrospun ECM-based hybrid scaffolds for cardiovascular tissue engineering

Electrospinning using natural proteins or synthetic polymers is a promising technique for the fabrication of fibrous scaffolds for various tissue engineering applications. However, one limitation of scaffolds electrospun from natural proteins is the need to cross-link with glutaraldehyde for stability, which has been postulated to lead to many complications in vivo including graft failure. In this study, we determined the characteristics of hybrid scaffolds composed of natural proteins including collagen and elastin, as well as gelatin, and the synthetic polymer poly(epsilon-caprolactone) (PCL), so to avoid chemical cross-linking. Fiber size increased proportionally with increasing protein and polymer concentrations, whereas pore size decreased. Electrospun gelatin/PCL scaffolds showed a higher tensile strength when compared to collagen/elastin/PCL constructs. To determine the effects of pore size on cell attachment and migration, both hybrid scaffolds were seeded with adipose-derived stem cells. Scanning electron microscopy and nuclei staining of cell-seeded scaffolds demonstrated the complete cell attachment to the surfaces of both hybrid scaffolds, although cell migration into the scaffold was predominantly seen in the gelatin/PCL hybrid. The combination of natural proteins and synthetic polymers to create electrospun fibrous structures resulted in scaffolds with favorable mechanical and biological properties.

Engineering of fiber-reinforced tissues with anisotropic biodegradable nanofibrous scaffolds

The repair of dense fiber-reinforced tissues poses a significant challenge for the tissue engineering community. The function of these structures is largely dependent on their architectural form, and as such, scaffold organization is an important design parameter in generating tissue analogues. To address this issue, we have recently utilized electrospinning to instill controllable fiber anisotropy in nanofibrous scaffolds. This abstract details the mechanical characterization of the bulk and local properties of these scaffolds, and points to their potential application in the repair and/or generation of fiber-reinforced tissues that recapitulate the native form.

Quantitative analysis of cell adhesion on aligned micro- and nanofibers

In this study, we quantitatively analyzed the affinity of cell adhesion to aligned nanofibers composed of composites of poly(glycolic acid) (PGA) and collagen. Electrospun composite fibers were fabricated at various PGA/collagen weight mixing ratio (7, 18, 40, 67, and 86%) to generate fibers that ranged in diameter from 10 mum to 500 nm. Scanning electron microscopy (SEM) observation revealed that the PGA/collagen fibers were long and uniformly aligned, irrespective of the PGA/collagen weight mixing ratio. In addition, it was observed that a significantly higher number of NIH3T3 fibroblasts adhered to nanofibers with smaller diameters in comparison to fibers with larger diameters. The highest affinity of cell adhesion was observed in the PGA/collagen fibers with diameter of 500 nm and PGA/collagen weight mixing ratio of 40%. Furthermore, the adherent cells were more elongated on fibers with smaller diameters. Thus, based on the results here, PGA/collagen composite fibers are suitable for tissue culture studies and provide an attractive material for tissue engineering applications.

Mold-shaped, nanofiber scaffold-based cartilage engineering using human mesenchymal stem cells and bioreactor

BACKGROUND

Mesenchymal stem cell (MSC)-based tissue engineering is a promising future alternative to autologous cartilage grafting. This study evaluates the potential of using MSCs, seeded into electrospun, biodegradable polymeric nanofibrous scaffolds, to engineer cartilage with defined dimensions and shape, similar to grafts used for subcutaneous implantation in plastic and reconstructive surgery.

MATERIALS AND METHODS

Human bone marrow derived MSCs seeded onto nanofibrous scaffolds and placed in custom-designed molds were cultured for up to 42 days in bioreactors. Chondrogenesis was induced with either transforming growth factor-beta1 (TGF-beta1) alone or in combination with insulin-like growth factor-I (IGF-I).

RESULTS

Constructs exhibited hyaline cartilage histology with desired thickness and shape as well as favorable tissue integrity and shape retention, suggesting the presence of elastic tissue. Time-dependent increase in cartilage matrix gene expression was seen in both types of culture: at Day 42, TGF-beta1/IGF-I treated cultures showed higher collagen Type 2 and aggrecan expression. Both culture conditions showed significant time-dependent increase in sulfated glycosaminoglycan and hydroxyproline contents. TGF-beta1/IGF-I-treated samples were significantly stiffer; with equilibrium compressive Young's modulus values reaching 17 kPa by Day 42.

CONCLUSIONS

The successful ex vivo development of geometrically defined cartilaginous construct using customized molding suggests the potential of cell-based cartilage tissue for reconstructive surgery.

Engineering cartilage tissue

Cartilage tissue engineering is emerging as a technique for the regeneration of cartilage tissue damaged due to disease or trauma. Since cartilage lacks regenerative capabilities, it is essential to develop approaches that deliver the appropriate cells, biomaterials, and signaling factors to the defect site. The objective of this review is to discuss the approaches that have been taken in this area, with an emphasis on various cell sources, including chondrocytes, fibroblasts, and stem cells. Additionally, biomaterials and their interaction with cells and the importance of signaling factors on cellular behavior and cartilage formation will be addressed. Ultimately, the goal of investigators working on cartilage regeneration is to develop a system that promotes the production of cartilage tissue that mimics native tissue properties, accelerates restoration of tissue function, and is clinically translatable. Although this is an ambitious goal, significant progress and important advances have been made in recent years.

Biomimetic materials for tissue engineering

Tissue engineering and regenerative medicine is an exciting research area that aims at regenerative alternatives to harvested tissues for transplantation. Biomaterials play a pivotal role as scaffolds to provide three-dimensional templates and synthetic extracellular matrix environments for tissue regeneration. It is often beneficial for the scaffolds to mimic certain advantageous characteristics of the natural extracellular matrix, or developmental or wound healing programs. This article reviews current biomimetic materials approaches in tissue engineering. These include synthesis to achieve certain compositions or properties similar to those of the extracellular matrix, novel processing technologies to achieve structural features mimicking the extracellular matrix on various levels, approaches to emulate cell-extracellular matrix interactions, and biologic delivery strategies to recapitulate a signaling cascade or developmental/wound healing program. The article also provides examples of enhanced cellular/tissue functions and regenerative outcomes, demonstrating the excitement and significance of the biomimetic materials for tissue engineering and regeneration.

Tissue Engineering with Nano-Fibrous Scaffolds

Tissue Engineering is a rapidly evolving field in terms of cell source and scaffold fabrication. As the template for three dimensional tissue growth, the scaffold should emulate the native extracellular matrix, which is nano-fibrous. Currently, there are three basic techniques capable of generating nano-fibrous scaffolding: electrospinning, molecular self-assembly, and thermally induced phase separation. These scaffolds can then be further modified by various three dimensional surface modification techniques if necessary to more precisely emulate the native extracellular matrix. However, even without further modification, nano-fibrous scaffolds have been shown to have advantageous effects on cellular behavior and tissue formation when compared to more traditional types of scaffolding. This review focuses on the current state of tissue engineering with nano-fibrous scaffolding with particular emphasis on bone tissue engineering.

Fabrication of fibrous poly(butylene succinate)/wollastonite/apatite composite scaffolds by electrospinning and biomimetic process

In this paper, a novel kind of Poly(butylene succinate) (PBSU) /wollastonite/apatite composite scaffold was fabricated via electrospinning and biomimetic process. Pure PBSU scaffold and composite scaffolds with 12.5 wt% and 25 wt% wollastonite were firstly fabricated by electrospinning. SEM micrographs showed that all the electrospun scaffolds had homogeneous fibrous structures with interconnected pores and randomly oriented ultrafine fibers. The composite scaffolds were then surface modified using a biomimetic process. SEM and XRD results showed that apatite could deposit on the surfaces of the composite fibers after incubation in SBF and a novel fibrous structure with microspheres composed of worm-like apatite on composite fibers was formed. Incubation time and wollastonite content were found to influence the morphology of the scaffolds during the biomimetic process obviously. Both the amount and the size of the microspheres on the composite scaffolds increased with increased incubation time. After a certain incubation time, microspheres formed on the composite fibers with less wollastonite had a relatively larger size. Therefore, the microstructure of the composite scaffolds could be adjusted by controlling the wollastonite content and the incubation time. All of these results suggest that it is an effective approach to fabricate PBSU/wollastonite/apatite fibrous composite scaffolds with different material content and controllable microstructure for bone tissue engineering.

Biodegradable fibrous scaffolds composed of gelatin coated poly(epsilon-caprolactone) prepared by coaxial electrospinning

A facile coaxial electrospinning technique was devised to prepare biodegradable core-shell fibrous scaffolds with poly(epsilon-caprolactone) (PCL) comprising the core structure and gelatin forming the coating of the fibers. The effect of the feed rate of the inner dope on the electrospinning process and fiber morphology was investigated. The results indicated that core-shell fibers with narrow size distribution and smooth surface morphology could be obtained when the feed rate was below 8 mL/h. An increase of the feed rate resulted in analogous increase in the diameters of both the inner PCL fiber core and the entire core-shell fibers. XPS analyses revealed that the surface of the core-shell fibers was tainted with a small amount of PCL. The outer gelatin layer in the core-shell fibers was crosslinked with glutaraldehyde. By optimizing the glutaraldehyde/gelatin feed ratio, crosslinked scaffolds with high porosity were obtained. The mechanic strength of the hydrated, crosslinked core-shell fibrous scaffolds was significantly enhanced because of the presence of hydrophobic PCL in the core region of the fibers. Results of cell culture studies suggested that the crosslinked, core-shell fibrous scaffold were nontoxic and capable of supporting fibroblast adhesion and proliferation.

Electrospun nanostructured scaffolds for tissue engineering applications

Despite being known for decades (since 1934), electrospinning has emerged recently as a very widespread technology to produce synthetic nanofibrous structures. These structures have morphologies and fiber diameters in a range comparable with those found in the extracellular matrix of human tissues. Therefore, nanofibrous scaffolds are intended to provide improved environments for cell attachment, migration, proliferation and differentiation when compared with traditional scaffolds. In addition, the process versatility and the highly specific surface area of nanofiber meshes may facilitate their use as local drug-release systems. Common electrospun nanofiber meshes are characterized by a random orientation. However, in some special cases, aligned distributions of the fibers can be obtained, with an interconnected microporous structure. The characteristic pore sizes and the inherent planar structure of the meshes can be detrimental for the desired cell infiltration into the inner regions, and eventually compromise tissue regeneration. Several strategies can be followed to overcome these limitations, and are discussed in detail here.

The effect of the alignment of electrospun fibrous scaffolds on Schwann cell maturation

Peripheral nerve regeneration can be enhanced by the stimulation of formation of bands of Büngner prior to implantation. Aligned electrospun poly(epsilon-caprolactone) (PCL) fibers were fabricated to test their potential to provide contact guidance to human Schwann cells. After 7 days of culture, cell cytoskeleton and nuclei were observed to align and elongate along the fiber axes, emulating the structure of bands of Büngner. Microarray analysis revealed a general down-regulation in expression of neurotrophin and neurotrophic receptors in aligned cells as compared to cells seeded on two-dimensional PCL film. Real-time-PCR analyses confirmed the up-regulation of early myelination marker, myelin-associated glycoprotein (MAG), and the down-regulation of NCAM-1, a marker of immature Schwann cells. Similar gene expression changes were also observed on cells cultured on randomly oriented PCL electrospun fibers. However, up-regulation of the myelin-specific gene, P0, was observed only on aligned electrospun fibers, suggesting the propensity of aligned fibers in promoting Schwann cell maturation.

Design and Characterization of Poly(Ethylene Glycol) Photopolymerizable Semi-Interpenetrating Networks for Chondrogenesis of Human Mesenchymal Stem Cells

Mesenchymal stem cells (MSCs) are used extensively in cartilage tissue engineering. We have developed a photopolymerizable poly(ethylene glycol diacrylate) (PEGDA) and poly(ethylene glycol) (PEG) semi-interpenetrating network that facilitates the in vitro chondrogenesis of human MSCs (hMSCs). Network parameters were altered and tested for their effects on subsequent matrix elaboration. The mesh size, calculated for each network based on equilibrium swelling ratios, was larger with lower PEGDA:PEG ratios and with higher PEGDA molecular weight. Changes in xi correlated with changes in extracellular matrix content and deposition in hMSC-seeded networks cultured in vitro for 6 weeks in defined chondrogenic medium. Networks constructed with PEGDA (6 kDa) and PEG (88 kDa) at 1:2 displayed intercellular deposition of proteoglycan. Furthermore, their proteoglycan contents were significantly higher than with PEGDA (6 kDa) hydrogels constructed without the PEG component and those constructed at a PEGDA:PEG ratio of 2:1, which both exhibited pericellular proteoglycan deposition. However, networks constructed with PEGDA (12 and 20 kDa) and PEG (88 kDa) exhibited intercellular deposition of proteoglycan regardless of the ratio employed. Collagen content was lower in networks constructed with PEGDA (12 and 20 kDa) and PEG (88 kDa) at a ratio of 1:2 than in those fabricated at the same PEGDA molecular weights at a ratio of 2:1. This study demonstrated that semi-interpenetrating network parameters influence not only extracellular matrix content, but also the deposition of the matrix molecules by hMSCs undergoing chondrogenesis. It is important that these parameters be considered carefully when creating scaffolds for tissue-engineered cartilage.

Nanofibers and their applications in tissue engineering

Developing scaffolds that mimic the architecture of tissue at the nanoscale is one of the major challenges in the field of tissue engineering. The development of nanofibers has greatly enhanced the scope for fabricating scaffolds that can potentially meet this challenge. Currently, there are three techniques available for the synthesis of nanofibers: electrospinning, self-assembly, and phase separation. Of these techniques, electrospinning is the most widely studied technique and has also demonstrated the most promising results in terms of tissue engineering applications. The availability of a wide range of natural and synthetic biomaterials has broadened the scope for development of nanofibrous scaffolds, especially using the electrospinning technique. The three dimensional synthetic biodegradable scaffolds designed using nanofibers serve as an excellent framework for cell adhesion, proliferation, and differentiation. Therefore, nanofibers, irrespective of their method of synthesis, have been used as scaffolds for musculoskeletal tissue engineering (including bone, cartilage, ligament, and skeletal muscle), skin tissue engineering, vascular tissue engineering, neural tissue engineering, and as carriers for the controlled delivery of drugs, proteins, and DNA. This review summarizes the currently available techniques for nanofiber synthesis and discusses the use of nanofibers in tissue engineering and drug delivery applications.

Improved cellular infiltration in electrospun fiber via engineered porosity

Small pore sizes inherent to electrospun matrices can hinder efficient cellular ingrowth. To facilitate infiltration while retaining its extracellular matrix-like character, electrospinning was combined with salt leaching to produce a scaffold having deliberate, engineered delaminations. We made elegant use of a specific randomizing component of the electrospinning process, the Taylor Cone and the falling fiber beneath it, to produce a uniform, well-spread distribution of salt particles. After 3 weeks of culture, up to 4 mm of cellular infiltration was observed, along with cellular coverage of up to 70% within the delaminations. To our knowledge, this represents the first observation of extensive cellular infiltration of electrospun matrices. Infiltration appears to be driven primarily by localized proliferation rather than coordinated cellular locomotion. Cells also moved from the salt-generated porosity into the surrounding electrospun fiber matrix. Given that the details of salt deposition (amount, size, and number density) are far from optimized, the result provides a convincing illustration of the ability of mammalian cells to interact with appropriately tailored electrospun matrices. These layered structures can be precisely fabricated by varying the deposition interval and particle size conceivably to produce in vivo-like gradients in porosity such that the resulting scaffolds better resemble the desired final structure.

Tissue Engineering the Mandibular Condyle

Tissue engineering provides the revolutionary possibility for curing temporomandibular joint (TMJ) disorders. Although characterization of the mandibular condyle has been extensively studied, tissue engineering of the mandibular condyle is still in an inchoate stage. The purpose of this review is to provide a summary of advances relevant to tissue engineering of mandibular cartilage and bone, and to serve as a reference for future research in this field. A concise anatomical overview of the mandibular condyle is provided, and the structure and function of the mandibular condyle are reviewed, including the cell types, extracellular matrix (ECM) composition, and biomechanical properties. Collagens and proteoglycans are distributed heterogeneously (topographically and zonally). The complexity of collagen types (including types I, II, III, and X) and cell types (including fibroblast-like cells, mesenchymal cells, and differentiated chondrocytes) indicates that mandibular cartilage is an intermediate between fibrocartilage and hyaline cartilage. The fibrocartilaginous fibrous zone at the surface is separated from hyaline-like mature and hypertrophic zones below by a thin and highly cellular proliferative zone. Mechanically, the mandibular condylar cartilage is anisotropic under tension (stiffer anteroposteriorly) and heterogeneous under compression (anterior region stiffer than posterior). Tissue engineering of mandibular condylar cartilage and bone is reviewed, consisting of cell culture, growth factors, scaffolds, and bioreactors. Ideal engineered constructs for mandibular condyle regeneration must involve two distinct yet integrated stratified layers in a single osteochondral construct to meet the different demands for the regeneration of cartilage and bone tissues. We conclude this review with a brief discussion of tissue engineering strategies, along with future directions for tissue engineering the mandibular condyle.

Surface modification of biodegradable electrospun nanofiber scaffolds and their interaction with fibroblasts

Biodegradable polymers, such as poly(glycolic acid) (PGA), poly(L-lactic acid) (PLLA) and poly(lactic-co-glycolic acid) (PLGA), were dissolved individually in the proper solvents and then subjected to electrospinning process to make nanofibrous scaffolds. Their surfaces were then chemically modified using oxygen plasma treatment and in situ grafting of hydrophilic acrylic acid (AA). The fiber thickness, pore size and porosity were estimated to 200-800 nm, 2-30 microm and 94-96%, respectively, and these properties were insignificant in the PGA, PLLA and PLGA nanofibrous scaffolds. The ultimate tensile strength of PGA was about 2.5 MPa on average and that of PLGA and PLLA was less than 2 MPa. The elongation-at-break was 100-130% for the three nanofibrous scaffolds. When the surface properties of AA-grafted scaffolds were examined, higher ratios of oxygen to carbon, lower contact angles and the presence of carboxylic (-COOH) groups were identified. The properties were significantly different from those of the unmodified nanofibrous scaffolds. Fibroblasts once seeded on the scaffolds were spreading over large surface area on the AA-grafted surface as compared to the unmodified PGA, PLLA and PLGA nanofibrous scaffolds. Cultured for up to 6 days, the fibroblast proliferation was found to be much better on the surface-modified nanofibrous scaffolds. The present study showed that, with the use of plasma treatment and AA grafting, the hydrophilic functional groups could be successfully adapted on the surface of electrospun nanofibrous scaffolds. Those surface-modified scaffolds made significant improvement on cell attachment and proliferation in vitro.

Regional multilineage differentiation potential of meniscal fibrochondrocytes: implications for meniscus repair

The knee menisci are wedge-shaped semilunar fibrocartilaginous structures that reside between the femur and tibia and function to transmit and distribute load. These structures have characteristics of both fibrous and cartilaginous tissues. The cartilage-like inner region and the fibrous vascularized outer region each has a distinct extracellular matrix, and resident meniscal fibrochondrocytes (MFCs) with distinct morphologies dependent on their location. Damage to the meniscus is common, and disruption of tissue structure and function result in erosion of the underlying articular cartilage. It has been observed that damage in the vascular periphery undergoes spontaneous repair, whereas damage of the inner region does not heal. While vascularity of the peripheral region plays a role in healing, recent findings have also suggested that local cellular composition influences local healing capacity. This study examined the variation in multipotential characteristics of cell populations isolated from different regions of the bovine meniscus. MFCs were isolated from the outer (vascular), inner (avascular), and horn (mixed) regions and induced toward chondrogenic, adipogenic, and osteogenic lineages. The results of this study suggest that MFCs from all regions of the meniscus possess a multilineage differentiation capability, particularly toward chondrogenesis and adipogenesis. MFCs from the outer region were most plastic, differentiating along all three mesenchymal lineages. These findings may underlie the experimental observation of improved integration of meniscus grafts from the outer zone and may have implications for developing strategies of cell-based meniscus repair.

Morphology, cytoskeletal organization, and myosin dynamics of mouse embryonic fibroblasts cultured on nanofibrillar surfaces

Growth of cells in tissue culture is generally performed on two-dimensional (2D) surfaces composed of polystyrene or glass. Recent work, however, has shown that such 2D cultures are incomplete and do not adequately represent the physical characteristics of native extracellular matrix (ECM)/basement membrane (BM), namely dimensionality, compliance, fibrillarity, and porosity. In the current study, a three-dimensional (3D) nanofibrillar surface composed of electrospun polyamide nanofibers was utilized to mimic the topology and physical structure of ECM/BM. Additional chemical cues were incorporated into the nanofibrillar matrix by coating the surfaces with fibronectin, collagen I, or laminin-1. Results from the current study show an enhanced response of primary mouse embryonic fibroblasts (MEFs) to culture on nanofibrillar surfaces with more dramatic changes in cell spreading and reorganization of the cytoskeleton than previously observed for established cell lines. In addition, the cells cultured on nanofibrillar and 2D surfaces exhibited differential responses to the specific ECM/BM coatings. The localization and activity of myosin II-B for MEFs cultured on nanofibers was also compared. A dynamic redistribution of myosin II-B was observed within membrane protrusions. This was previously described for cells associated with nanofibers composed of collagen I but not for cells attached to 2D surfaces coated with monomeric collagen. These results provide further evidence that nanofibrillar surfaces offer a significantly different environment for cells than 2D substrates.

The role of electrospinning in the emerging field of nanomedicine

The fact that in vivo the extracellular matrix (ECM) or substratum with which cells interact often includes topography at the nanoscale underscores the importance of investigating cell-substrate interactions and performing cell culture at the submicron scale. An important and exciting direction of research in nanomedicine would be to gain an understanding and exploit the cellular response to nanostructures. Electrospinning is a simple and versatile technique that can produce a macroporous scaffold comprising randomly oriented or aligned nanofibers. It can also accommodate the incorporation of drug delivery function into the fibrous scaffold. Endowed with both topographical and biochemical signals such electrospun nanofibrous scaffolds may provide an optimal microenvironment for the seeded cells. This review covers the analysis and control of the electrospinning process, and describes the types of electrospun fibers fabricated for biomedical applications such as drug delivery and tissue engineering.

Substrate mineralization stimulates focal adhesion contact redistribution and cell motility of bone marrow stromal cells

Understanding the mechanisms of substrate based control of cell function is critical to the design of biomaterials. Cells interact with their extracellular matrix through cell adhesion contacts. We have previously described the self assembly of bone-like mineral onto an organic template and have shown that these biomimetic surfaces lead to an increased volume fraction of bone regenerated in vivo. In the present study, we compared the distribution of cell adhesion contacts, cell spreading, and cell motility of murine bone marrow stromal cells (BMSC) on mineralized vs. nonmineralized substrates. We developed a new approach for quantification of cell-material interactions and demonstrated that cell adhesion contacts on mineralized substrates were distributed throughout the cell surface contacting the substrate, whereas on nonmineralized substrates cell adhesion contacts were present near the cell periphery. We propose that mineralized substrates stimulate the predominant expression of fibrillar contacts, and nonmineralized substrates stimulate expression of focal adhesion contacts. Cell motility assays with colloidal gold demonstrated a statistically significant decrease in the average phagokinetic index of migrating cells on mineralized vs. nonmineralized substrates after 90 min of cell seeding. We propose that the physical-chemical properties of the substrate, altered by mineralization, cause expression of specific types of cell contacts and, as a result, modify molecular mechanisms responsible for cell spreading, motility, and possibly differentiation.

Electrospun scaffold tailored for tissue-specific extracellular matrix

The natural extracellular matrix (ECM) is a complex structure that is built to meet the specific requirements of the tissue and organ. Primarily consisting of nanometer diameter fibrils, ECM may contain other vital substances such as proteoglycans, glycosaminoglycan and various minerals. Current research in tissue engineering involves trying to replicate the ECM such that it provides the environment for tissue regeneration. Electrospinning is a versatile process that results in nanofibers by applying a high voltage to electrically charge a liquid. A variety of polymers and other substances have been incorporated into the artificial nanofibrous scaffold. Surface modification and cross-linking of the nanofibers are some ways to improve the biocompatibility and stability of the scaffold. Electrospun scaffolds with oriented nanofibers and other assemblies can be constructed by modifying the electrospinning setup. Using electrospinning, researchers are able to specifically tailor the electrospun scaffold to meet the requirements of the tissue that they seek to regenerate. In vitro and in vivo experiments demonstrate that electrospun scaffolds hold great potential for tissue engineering applications.

Fibronectin and culture temperature modulate the efficacy of an avidin–biotin binding system for chondrocyte adhesion and growth on biodegradable polymers

Cell adhesion to a scaffold is a prerequisite for tissue engineering. Many studies have been focused on enhancing cell adhesion to synthetic materials that are used for scaffold fabrication. Previously, we showed that immobilization of biotin molecules to chondrocyte surfaces enhanced cell adhesion to avidin-coated biodegradable polymers such as poly-L-lactic acid, poly-D,L-lactic acid and polycaprolactone. However, the endocytosis of cell membrane biotin molecules decreases binding strength between biotinylated-chondrocytes (B-chondrocytes) and avidin-coated substrata, and therefore decreases cell spreading and discourages long-term chondrocytes culture. In this study, we proposed two strategies to solve the shortcoming of the avidin-biotin binding system. First, the avidin-biotin binding system is combined with the intrinsic integrin-dependent adhesion systems in order to enhance long-term cell culture. Second, the incubation temperature is lowered in order to slow down the endocytosis process. We found that the avidin-biotin binding system in combination with FN-integrin binding system enhanced cell adhesion, cell spreading and cell growth. Decrease of cell culture temperature to 4 degrees C enhanced the adhesion of B-chondrocytes to the avidin-coated surfaces, but decreased cell viability and proliferation, compared to culture temperature of 37 degrees C. Whether there is an optimal seeding temperature between 4 and 37 degrees C for both adhesion and proliferation of B-chondrocytes needs further investigation. Our results indicated that modulation of the adhesion conditions could further enhance the efficacy of the avidin-biotin binding system in mediating cell adhesion, and subsequent tissue culture.

Nanobiomaterial applications in orthopedics

Advancements in nanobiotechnology are revolutionizing our capability to understand biological intricacies and resolve biological and medical problems by developing subtle biomimetic techniques. Nanocomposites and nanostructured materials are believed to play a pivotal role in orthopedic research since bone itself is a typical example of a nanocomposite. This article reviews current strategies using nanobiomaterials to improve current orthopedic materials and examines their applications in bone tissue engineering. Preliminary investigations support the potential of nanobiomaterials in orthopedic applications; however, significant advancements are necessary to achieve clinical use. Overall, current trends in nanobiotechnology foreshadow a bright future through the use of nanobiomaterials in the orthopedic domain.

Encapsulated chondrocyte response in a pulsatile flow bioreactor

We have developed a bioreactor-based millifluidic technique that allows for dynamic culture conditions and measurement of the fluid flow impinging upon a three-dimensional tissue engineering scaffold. Chondrocytes in scaffolds have been shown to require mechanical stimulation to produce an extracellular matrix that resembles native cartilage. This study investigates the effect of pulsatile flow on chondrocyte response in a model poly(ethylene glycol) dimethacrylate hydrogel. Bovine chondrocytes were encapsulated in the hydrogel and cultured for 7, 14 and 21 days at pulsatile flow frequencies of 0.5 Hz (15ml/min) and 1.5Hz (17ml/min). The scaffolds cultured under dynamic conditions were compared to those cultured under static (non-flow) conditions. Quantitative real-time reverse transcription polymerase chain reaction was used to quantify collagen type I, collagen type II and aggrecan gene copy numbers as markers for chondrocyte phenotypic expression. Histological sections stained with hematoxylin & eosin, and Alcian blue confirmed chondrocyte morphology and matrix formation. Interestingly, regulation of the collagen type II gene was particularly sensitive to the flow conditions. The understanding of the cell response to encapsulation and flow could be used to identify the appropriate culture conditions necessary to design and develop hydrogel carriers to promote the formation of extracellular matrix as well as to further our knowledge of chondrocyte mechanobiology.

Aligned Protein-Polymer Composite Fibers Enhance Nerve Regeneration: A Potential Tissue-Engineering Platform

Sustained release of proteins from aligned polymeric fibers holds great potential in tissue-engineering applications. These protein-polymer composite fibers possess high surface-area-to-volume ratios for cell attachment, and can provide biochemical and topographic cues to enhance tissue regeneration. Aligned biodegradable polymeric fibers that encapsulate human glial cell-derived neurotrophic factor (GDNF, 0.13 wt%) were fabricated via electrospinning a copolymer of caprolactone and ethyl ethylene phosphate (PCLEEP) with GDNF. The protein was randomly dispersed throughout the polymer matrix in aggregate form, and released in a sustained manner for up to two months. The efficacy of these composite fibers was tested in a rat model for peripheral nerve-injury treatment. Rats were divided into four groups, receiving either empty PCLEEP tubes (control); tubes with plain PCLEEP electrospun fibers aligned longitudinally (EF-L) or circumferentially (EF-C); or tubes with aligned GDNF-PCLEEP fibers (EF-L-GDNF). After three months, bridging of a 15 mm critical defect gap by the regenerated nerve was observed in all the rats that received nerve conduits with electrospun fibers, as opposed to 50% in the control group. Electrophysiological recovery was seen in 20%, 33%, and 44% of the rats in the EF-C, EF-L, and EF-L-GDNF groups respectively, whilst none was observed in the controls. This study has demonstrated that, without further modification, plain electrospun fibers can help in peripheral nerve regeneration; however, the synergistic effect of an encapsulated growth factor facilitated a more significant recovery. This study also demonstrated the novel use of electrospinning to incorporate biochemical and topographical cues into a single implant for in vivo tissue-engineering applications.

Interaction of cells and nanofiber scaffolds in tissue engineering

Nanofibers and nanomaterials are potentially recent additions to materials in relation to tissue engineering (TE). TE is the regeneration of biological tissues through the use of cells, with the aid of supporting structures and biomolecules. Mimicking architecture of extracellular matrix is one of the challenges for TE. Biodegradable biopolymer nanofibers with controlled surface and internal molecular structures can be electrospun into mats with specific fiber arrangement and structural integrity for drug delivery and TE applications. The polymeric materials are widely accepted because of their ease of processability and amenability to provide a large variety of cost-effective materials, which help to enhance the comfort and quality of life in modern biomedical and industrial society. Today, nanotechnology and nanoscience approaches to scaffold design and functionalization are beginning to expand the market for drug delivery and TE is forming the basis for highly profitable niche within the industry. This review describes recent advances for fabrication of nanofiber scaffolds and interaction of cells in TE.

Technology Insight: adult stem cells in cartilage regeneration and tissue engineering

Articular cartilage, the load-bearing tissue of the joint, has limited repair and regeneration potential. The scarcity of treatment modalities for large chondral defects has motivated attempts to engineer cartilage tissue constructs that can meet the functional demands of this tissue in vivo. Cartilage tissue engineering requires three components: cells, scaffold, and environment. Adult stem cells, specifically multipotent mesenchymal stem cells, are considered the cell type of choice for tissue engineering, because of the ease with which they can be isolated and expanded and their multilineage differentiation capabilities. Successful outcome of cell-based cartilage tissue engineering ultimately depends on the proper differentiation of stem cells into chondrocytes and the assembly of the appropriate cartilaginous matrix to achieve the load-bearing capabilities of the natural articular cartilage. Multiple requirements, including growth factors, signaling molecules, and physical influences, need to be met. Adult mesenchymal stem-cell-based tissue engineering is a promising technology for the development of a transplantable cartilage replacement to improve joint function.

Engineering controllable anisotropy in electrospun biodegradable nanofibrous scaffolds for musculoskeletal tissue engineering

Many musculoskeletal tissues exhibit significant anisotropic mechanical properties reflective of a highly oriented underlying extracellular matrix. For tissue engineering, recreating this organization of the native tissue remains a challenge. To address this issue, this study explored the fabrication of biodegradable nanofibrous scaffolds composed of aligned fibers via electrospinning onto a rotating target, and characterized their mechanical anisotropy as a function of the production parameters. The characterization showed that nanofiber organization was dependent on the rotation speed of the target; randomly oriented fibers (33% fiber alignment) were produced on a stationary shaft, whereas highly oriented fibers (94% fiber alignment) were produced when rotation speed was increased to 9.3m/s. Non-aligned scaffolds had an isotropic tensile modulus of 2.1+/-0.4MPa, compared to highly anisotropic scaffolds whose modulus was 11.6+/-3.1MPa in the presumed fiber direction, suggesting that fiber alignment has a profound effect on the mechanical properties of scaffolds. Mechanical anisotropy was most pronounced at higher rotation speeds, with a greater than 33-fold enhancement of the Young's modulus in the fiber direction compared to perpendicular to the fiber direction when the rotation speed reached 8m/s. In cell culture, both the organization of actin filaments of human mesenchymal stem cells and the cellular alignment of meniscal fibroblasts were dictated by the prevailing nanofiber orientation. This study demonstrates that controllable and anisotropic mechanical properties of nanofibrous scaffolds can be achieved by dictating nanofiber organization through intelligent scaffold design.