Coagulation/flocculation process for dye removal using sludge from water treatment plant: optimization through response surface methodology

Degradation of Acid Red 274 using H2O2 in subcritical water: application of response surface methodology

In this research, the degradation of Acid Red 274 (AR 274) was investigated under subcritical water conditions using H(2)O(2), which led to the oxidative degradation of Acid Red 274 up to its 80% of mineralization. The Box-Behnken design matrix and response surface methodology (RSM) were applied in designing the experiments for evaluating the interactive effects of the three most important operating variables. Thus, the interactive effects of temperature (100-250°C), oxidant (H(2)O(2)) concentration (50-250 mM), and time (30-60 min.) on the degradation of AR 274 were investigated. A total of 17 experiments were conducted in this research, and the analysis of variance (ANOVA) indicated that the proposed quadratic model could be used for navigating the design space. The proposed model was essentially in accordance with the experimental case with correlation coefficient R(2)=0.9930 and Adj-R(2)=0.9839, respectively. The results confirmed that RSM based on the Box-Behnken design was a compatible method for optimizing the operating conditions of AR 274 degradation.

Biosorption of food dyes onto Spirulina platensis nanoparticles: equilibrium isotherm and thermodynamic analysis

The biosorption of food dyes FD&C red no. 40 and acid blue 9 onto Spirulina platensis nanoparticles was studied at different conditions of pH and temperature. Four isotherm models were used to evaluate the biosorption equilibrium and the thermodynamic parameters were estimated. Infra red analysis (FT-IR) and energy dispersive X-ray spectroscopy (EDS) were used to verify the biosorption behavior. The maximum biosorption capacities of FD&C red no. 40 and acid blue 9 were found at pH 4 and 298 K, and the values were 468.7 mg g(-1) and 1619.4 mg g(-1), respectively. The Sips model was more adequate to fit the equilibrium experimental data (R2>0.99 and ARE<5%). Thermodynamic study showed that the biosorption was exothermic, spontaneous and favorable. FT-IR and EDS analysis suggested that at pH 4 and 298 K, the biosorption of both dyes onto nanoparticles occurred by chemisorption.

Pretreatment of wastewater: optimal coagulant selection using Partial Order Scaling Analysis (POSA)

Jar-test is a well-known tool for chemical selection for physical-chemical wastewater treatment. Jar test results show the treatment efficiency in terms of suspended matter and organic matter removal. However, in spite of having all these results, coagulant selection is not an easy task because one coagulant can remove efficiently the suspended solids but at the same time increase the conductivity. This makes the final selection of coagulants very dependent on the relative importance assigned to each measured parameter. In this paper, the use of Partial Order Scaling Analysis (POSA) and multi-criteria decision analysis is proposed to help the selection of the coagulant and its concentration in a sequencing batch reactor (SBR). Therefore, starting from the parameters fixed by the jar-test results, these techniques will allow to weight these parameters, according to the judgments of wastewater experts, and to establish priorities among coagulants. An evaluation of two commonly used coagulation/flocculation aids (Alum and Ferric Chloride) was conducted and based on jar tests and POSA model, Ferric Chloride (100 ppm) was the best choice. The results obtained show that POSA and multi-criteria techniques are useful tools to select the optimal chemicals for the physical-technical treatment.

Response surface optimization of acid red 119 dye from simulated wastewater using Al based waterworks sludge and polyaluminium chloride as coagulant

In this research, the performance of Polyaluminium Chloride (PAC) and Polyaluminium Chloride sludge (PACS) as coagulants for acid red 119 (AR119) dye removal from aqueous solutions were compared. The sample of PACS was collected from "Baba Sheikh Ali" water treatment plant (Isfahan, Iran) where PAC is used as a coagulant in the coagulation/flocculation process. A response surface methodology was applied to evaluate the simple and combined effects of the operating variables including initial pH, coagulant dosage and initial dye concentration and to optimize the operating conditions of the treatment process. Results reveal that the optimal conditions for dye removal were initial pH 3.42, coagulant dosage of 4.55 g dried PACS/L and initial dye concentration of 140 mg/L for PACS, while the optimal initial pH, coagulant dosage and initial dye concentration for PAC were 3.8, 57 mg/L and 140 mg/L, respectively. Under these optimal values of process parameters, the dye removal efficiency of 94.1% and 95.25% was observed for PACS and PAC, respectively. Although lower amount of PAC in comparison with PACS was needed for specific dye removal, the reuse of PACS as a low-cost material can offer some advantages such as high efficiency for AR119 dye removal and economic savings on overall water and wastewater treatment plant operation costs.

Study on adsorption and desorption properties of the starch grafted p-tert-butyl-calix[n]arene for butyl Rhodamine B solution

The adsorbents of starch grafted p-tert-butyl-calix[4,6,8]arene-SGCn (SGC4, SGC6, SGC8) are prepared. The products are characterized by FTIR, elemental analysis, thermal gravimetric analysis and scanning electron microscope. Static adsorption behavior is studied by using SGC8 as adsorbent, butyl Rhodamine B (BRB) solution as simulation dye wastewater. The adsorption of BRB onto SGC8 fits the second order kinetic model and the apparent adsorption rate constant is 0.002 g mg(-1)min(-1) at 25 °C. The equilibrium adsorption data are interpreted using Langmuir and Freundlich models. The adsorption of BRB onto SGC8 is better represented by the Langmuir equation. The thermodynamic parameters for the adsorption reaction are calculated through van't Hoff analysis. The adsorbent may be easily regenerated by using ethanol solution as desorption agent to extract dye from SGC8. The rate of desorption of BRB is dependent on the concentration of ethanol and the temperature. SGC8 exhibits excellent adsorption and desorption properties toward dye molecule. The new-style adsorbent of SGC8 is regarded as a potential adsorbent to deal with dye or organic wastewater.